| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
|
|
Kalle Valo says:
====================
wireless-drivers fixes for 5.4
First set of fixes for 5.4 sent during the merge window. Most are
regressions fixes but the mt7615 problem has been since it was merged.
iwlwifi
* fix a build regression related CONFIG_THERMAL
* avoid using GEO_TX_POWER_LIMIT command on certain firmware versions
rtw88
* fixes for skb leaks
zd1211rw
* fix a compiler warning on 32 bit
mt76
* fix the firmware paths for mt7615 to match with linux-firmware
wil6210
* fix use of skb after free
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The debug code dereferences "skb" to print "skb->len" so we have to
print the message before we free "skb".
Fixes: f99fe49ff372 ("wil6210: add wil_netif_rx() helper function")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The intention was to have the GEO_TX_POWER_LIMIT command in FW version
36 as well, but not all 8000 family got this feature enabled. The
8000 family is the only one using version 36, so skip this version
entirely. If we try to send this command to the firmwares that do not
support it, we get a BAD_COMMAND response from the firmware.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=204151.
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
mt7615 patch/n9/cr4 firmwares are available in mediatek folder in
linux-firmware repository. Because of this mt7615 won't work on regular
distributions like Ubuntu. Fix path definitions. Moreover remove useless
firmware name pointers and use definitions directly
Fixes: 04b8e65922f6 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Cc: stable@vger.kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
After firmware has been downloaded, driver should send
some information to it through H2C commands. Those H2C
commands are transmitted through TX path.
But before HCI has been started, the TX path is not
working completely. Such as PCI interfaces, the interrupts
are not enabled, hence TX interrupts will not be issued
after H2C skb has been DMAed to the device. And the H2C
skbs will not be released until the device is powered off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Consolidate _HPP/_HPX stuff in pci-acpi.c and simplify it
(Krzysztof Wilczynski)
- Fix incorrect PCIe device types and remove dev->has_secondary_link
to simplify code that deals with upstream/downstream ports (Mika
Westerberg)
- After suspend, restore Resizable BAR size bits correctly for 1MB
BARs (Sumit Saxena)
- Enable PCI_MSI_IRQ_DOMAIN support for RISC-V (Wesley Terpstra)
Virtualization:
- Add ACS quirks for iProc PAXB (Abhinav Ratna), Amazon Annapurna
Labs (Ali Saidi)
- Move sysfs SR-IOV functions to iov.c (Kelsey Skunberg)
- Remove group write permissions from sysfs sriov_numvfs,
sriov_drivers_autoprobe (Kelsey Skunberg)
Hotplug:
- Simplify pciehp indicator control (Denis Efremov)
Peer-to-peer DMA:
- Allow P2P DMA between root ports for whitelisted bridges (Logan
Gunthorpe)
- Whitelist some Intel host bridges for P2P DMA (Logan Gunthorpe)
- DMA map P2P DMA requests that traverse host bridge (Logan
Gunthorpe)
Amazon Annapurna Labs host bridge driver:
- Add DT binding and controller driver (Jonathan Chocron)
Hyper-V host bridge driver:
- Fix hv_pci_dev->pci_slot use-after-free (Dexuan Cui)
- Fix PCI domain number collisions (Haiyang Zhang)
- Use instance ID bytes 4 & 5 as PCI domain numbers (Haiyang Zhang)
- Fix build errors on non-SYSFS config (Randy Dunlap)
i.MX6 host bridge driver:
- Limit DBI register length (Stefan Agner)
Intel VMD host bridge driver:
- Fix config addressing issues (Jon Derrick)
Layerscape host bridge driver:
- Add bar_fixed_64bit property to endpoint driver (Xiaowei Bao)
- Add CONFIG_PCI_LAYERSCAPE_EP to build EP/RC drivers separately
(Xiaowei Bao)
Mediatek host bridge driver:
- Add MT7629 controller support (Jianjun Wang)
Mobiveil host bridge driver:
- Fix CPU base address setup (Hou Zhiqiang)
- Make "num-lanes" property optional (Hou Zhiqiang)
Tegra host bridge driver:
- Fix OF node reference leak (Nishka Dasgupta)
- Disable MSI for root ports to work around design problem (Vidya
Sagar)
- Add Tegra194 DT binding and controller support (Vidya Sagar)
- Add support for sideband pins and slot regulators (Vidya Sagar)
- Add PIPE2UPHY support (Vidya Sagar)
Misc:
- Remove unused pci_block_cfg_access() et al (Kelsey Skunberg)
- Unexport pci_bus_get(), etc (Kelsey Skunberg)
- Hide PM, VC, link speed, ATS, ECRC, PTM constants and interfaces in
the PCI core (Kelsey Skunberg)
- Clean up sysfs DEVICE_ATTR() usage (Kelsey Skunberg)
- Mark expected switch fall-through (Gustavo A. R. Silva)
- Propagate errors for optional regulators and PHYs (Thierry Reding)
- Fix kernel command line resource_alignment parameter issues (Logan
Gunthorpe)"
* tag 'pci-v5.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (112 commits)
PCI: Add pci_irq_vector() and other stubs when !CONFIG_PCI
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
PCI: vmd: Fix shadow offsets to reflect spec changes
PCI: vmd: Fix config addressing when using bus offsets
PCI: dwc: Add validation that PCIe core is set to correct mode
PCI: dwc: al: Add Amazon Annapurna Labs PCIe controller driver
dt-bindings: PCI: Add Amazon's Annapurna Labs PCIe host bridge binding
PCI: Add quirk to disable MSI-X support for Amazon's Annapurna Labs Root Port
PCI/VPD: Prevent VPD access for Amazon's Annapurna Labs Root Port
PCI: Add ACS quirk for Amazon Annapurna Labs root ports
PCI: Add Amazon's Annapurna Labs vendor ID
MAINTAINERS: Add PCI native host/endpoint controllers designated reviewer
PCI: hv: Use bytes 4 and 5 from instance ID as the PCI domain numbers
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
PCI: Get rid of dev->has_secondary_link flag
...
|
|
On 32-bit:
drivers/net/wireless/zydas/zd1211rw/zd_usb.c: In function ‘check_read_regs’:
drivers/net/wireless/zydas/zd1211rw/zd_def.h:18:25: warning: format ‘%ld’ expects argument of type ‘long int’, but argument 6 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
dev_printk(level, dev, "%s() " fmt, __func__, ##args)
^~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_def.h:22:4: note: in expansion of macro ‘dev_printk_f’
dev_printk_f(KERN_DEBUG, dev, fmt, ## args)
^~~~~~~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:1635:3: note: in expansion of macro ‘dev_dbg_f’
dev_dbg_f(zd_usb_dev(usb),
^~~~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:1636:51: note: format string is defined here
"error: actual length %d less than expected %ld\n",
~~^
%d
Fixes: 84b0b66352470e64 ("zd1211rw: zd_usb: Use struct_size() helper")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Interrupt is disabled to stop PCI, which means the skbs
queued for each TX ring will not be released via DMA
interrupt. To avoid those skbs remained being left in
the skb queue until PCI has been removed, driver needs
to release skbs by itself.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
These skbs free routines could be used when driver wants
to stop PCI bus, because some of the skbs remained in the
queue may not have been returned via DMA interrupt.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Without CONFIG_THERMAL, the driver fails to link as it calls
iwl_mvm_send_temp_report_ths_cmd() unconditionally. Fix this
by making that function available, but do almost nothing but
send the empty firmware command to enable CT-kill reporting.
While at it, also fix that function itself to not error out
when the thermal zone hasn't been initialized, but instead
just send the empty firmware command in this case as well.
Fixes: 242d9c8b9a93 ("iwlwifi: mvm: use FW thermal monitoring regardless of CONFIG_THERMAL")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Minor overlapping changes in the btusb and ixgbe drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ath.git patches for 5.4. Major changes:
wil6210
* add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11
* add debugfs file to show PCM ring content
* report boottime_ns in scan results
ath9k
* add a separate loader for AR92XX (and older) pci(e) without eeprom,
enabled with the new ATH9K_PCI_NO_EEPROM Kconfig option
|
|
Report chains and chain_signal in ieee80211_rx_status.
It is useful for program such as tcpdump to see if the
antennas are well connected/placed.
8822C is able to receive CCK rates with 2 antennas, while
8822B can only use 1 antenna path to receive CCK rates.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix the wrong RF path for CCK rx power calculation.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Function _rtl92d_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92d_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The hardware has enough buffer to receive like 8K for an MPDU.
So tell mac80211 that we can receive AMSDU in AMPDU.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This mechanism reduces the numbers of false alram in cck rate by
dynamically adjusting the value of power threshold and cs_ratio.
We determine the new value by three factors, which are rssi, false alarm
count and igi. Based on these factors, we define the current condition
into five levels. Compared to the previous level, if the level is changed,
we set the new values for power threshold and cs_ratio.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since 8822c requires to do not only IQK, but also DPK.
Move these calibrations that need to be done once the channel
is determined, into phy_calibration.
And note that the order of the calibrations matters, 8822c
should do IQK first, then DPK.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Power amplifiers are not linear components, and require DPK to
reduce its nonlinearity. DPK is called Digital Pre-distortion
Calibration, can be used to compensate the output of power.
DPK tracking is in charge of tracking the thermal changes. And
it then shifts the power curve accordingly, which makes the
power output remains linear even if the PA works in different
temperature.
To perform DPK, the parameter table should also be updated.
And the table will be applied when device is powered on.
Then DPK will reference the values to calibrate.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add support for doing IQK in firmware
Ideally the RF component's I/Q vectors should be orthogonal,
but usually they are not. So we need to calibrate for the RF
components, ex. PA/LNA, ADC/DAC.
And if the I/Q vectors are more orthogonal, the mixed signal
will have less deviation. This helps with those rates with
higher modulation (MCS8-9), because they have more strict
EVM/SNR requirement. Also the better of the quality of the
signal, the longer it can propagate, and the better throughput
performance we can get.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable 8822C Tx/Rx interrupt migration.
In some platforms, performance test may cause heavy cpu loading and get
bad results. Interrupt migration can decrease the amount of interrupts,
and lower cpu loading.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
update sequence to v13 to reduce power consumption
when MAC power off
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Update PHY hardware parameters to v38.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Each of these drivers defines some device to host macros that are never
used, thus they can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
iAs the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With the commit e86dc1ca4676 ("Libertas: cfg80211 support") we've lost
the ability to actually set the Mesh SSID from userspace.
NL80211_CMD_SET_INTERFACE with NL80211_ATTR_MESH_ID sets the mesh point
interface's ssid field. Let's use that one for the Libertas Mesh
operation
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The array channel_all can be make static const rather than populating
it on the stack, this makes the code smaller. Also, variable place
is being initialized with a value that is never read, so this assignment
is redundant and can be removed.
Before:
text data bss dec hex filename
118537 9591 0 128128 1f480 realtek/rtlwifi/rtl8821ae/phy.o
After:
text data bss dec hex filename
118331 9687 0 128018 1f412 realtek/rtlwifi/rtl8821ae/phy.o
Saves 110 bytes, (gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Providing a new wiphy on every PCIe reset was confusing and was causing
configuration problems for some users (supplicant and authenticators).
Sticking to the existing wiphy should make error recovery much simpler
and more reliable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Move code allocating/freeing wiphy out of above functions. This will
allow reinitializing the driver (e.g. on some error) without allocating
a new wiphy.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This moves "ops" pointer from "struct brcmf_cfg80211_info" to the
"struct brcmf_pub". This movement makes it possible to allocate wiphy
without attaching cfg80211 (brcmf_cfg80211_attach()). It's required for
later separation of wiphy allocation and driver initialization.
While at it fix also an unlikely memory leak in the brcmf_attach().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There are special kinds of FW such as WMI only which
are used for testing, diagnostics and other specific
scenario.
Such FW is loaded during driver probe and the driver
disallows enabling any network interface, to avoid
operational issues.
In many cases it is used to debug early versions
of FW with new features, which sometimes fail
on startup.
Currently when such FW fails to load (for example,
because of init failure), the driver probe would fail
and shutdown the device making it difficult to debug
the early failure.
To fix this, ignore load failures in WMI only FW and
allow driver probe to succeed, making it possible to
continue and debug the FW load failure.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The short frame check in wil_sring_reap_rx_edma uses
skb->len which store the maximum frame length. Fix
this to use dmalen which is the actual length of
the received frame.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
writel_relaxed can be used in wil_debugfs_iomem_x32_set
since there is a wmb call immediately after.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Call cfg80211_inform_bss_frame_data to report cfg80211 on the
boottime_ns in order to prevent the scan results filtering due to
aging.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Upon driver rmmod, cancel_work_sync() can be invoked on
p2p.discovery_expired_work before this work struct was initialized.
This causes a WARN_ON with newer kernel version.
Add initialization of discovery_expired_work inside wil_vif_init().
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
cid value is not being verified in wmi_evt_delba(),
verification is added.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Due to compiler optimization, it's possible that dr_bit (descriptor
ready) is read last from the status message.
Due to race condition between HW writing the status message and
driver reading it, other fields that were read earlier (before dr_bit)
could have invalid values.
Fix this by explicitly reading the dr_bit first and then using rmb
before reading the rest of the status message.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix a race between cfg80211 add_key call and transmitting of 4/4 EAP
packet. In case the transmit is delayed until after the add key takes
place, message 4/4 will be encrypted with the new key, and the
receiver side (AP) will drop it due to MIC error.
Wil6210 will monitor and look for the transmitted packet 4/4 eap key.
In case add_key takes place before the transmission completed, then
wil6210 will let the FW store the key and wil6210 will notify the FW
to use the PTK key only after 4/4 eap packet transmission was
completed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
Linus Torvalds
David S. Miller
Krzysztof Kozlowski
Dan Carpenter
Luca Coelho
Lorenzo Bianconi
Yan-Hsuan Chuang
Geert Uytterhoeven
Johannes Berg
Kalle Valo
Tsang-Shian Lin
Michael Straube
Tzu-En Huang
Chin-Yen Lee
Larry Finger
Lubomir Rintel
zhong jiang
Colin Ian King
Rafał Miłecki
Lior David
Maya Erez
Dedy Lansky
Alexei Avshalom Lazar
Ahmad Masri