| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fix following static checker warning in mt76u_buf_free:
drivers/net/wireless/mediatek/mt76/usb.c:372 mt76u_buf_free()
warn: address of 'urb->sg[i]' is non-NULL
There is no need to check sg page pointer since urb->num_sgs
has been already validated in mt76u_fill_rx_sg
Fixes: cb83585e1121 ("mt76: usb: fix possible memory leak in mt76u_buf_free")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Don't need separate file just for kmalloc/kfree.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Use usb_bulk_msg for reading MCU command responses. This simplify code
a lot.
Together with 97a3005759c ("mt76usb: allow mt76u_bulk_msg be used
for reads") it also fix possible problems with rx data buffers
not being aligned and contained within single page. After doing
page_frag_alloc(1024) consecutive page_frag_alloc(PAGE_SIZE) will
alloc PAGE_SIZE buffer at PAGE_SIZE - 1024 offset.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Extend mt76u_bulk_msg() such it can be used for synchronous bulk reads.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
It needs to be always enabled for 76x2 and conditionally enabled/disabled
for 76x0. Since mt76x2_mac_stop clears this bit, ensure that it is enabled
in mt76x02_edcca_init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
They are now the same and short enough to be turned into an inline function
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
ED/CCA needs to be disable before stopping the MAC to avoid hangs from tx
being blocked. It must only be enabled again after the MAC has been started
again.
In many places this wasn't done properly, so fix this by always clearing
the relevant ED/CCA bits in mt76x2_mac_stop and set it up again after
channel change or calibration is done
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
MCU request timeout usually indicates that the device is no longer responsive,
and it usually does not recover without a reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
When the timer is already running, there is no need to reset the counter,
because the drift will remain the same.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
When mt76x0 and mt76x2 beacon code was unified, it changed the order in which
beacon enable and beacon interval are configured.
Configuring beacon enable before beacon interval can in some cases cause
problems with the beacon timer, leading to clients not waking up properly
from powersave mode.
Fix this by changing the order back to interval first, then enable.
Fixes: cc726268e4dce ("mt76: move mt76x02_bss_info_changed in mt76x02-lib module")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Check the count before incrementing it to match vendor code behavior.
This defers the adjustment by one more tick, which should improve accuracy
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
MT_BEACON_TIME_CFG_SYNC_MODE needs to be set for AP mode, according to the
documentation. For other modes it should be irrelevant in this case.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge net-next to resolve a conflict and to get the mac80211
rhashtable fixes so further patches can be applied on top.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Update element names and new fields according to D3.3 of
the HE spec.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
genlmsg_reply can fail, so propagate its return code
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a few PCI ID'S for 22000 and killer series in addition to
chainging the marketing name.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add one PCI ID for 9260 series.
CC: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Implement Rx fifos dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Implement Tx fifos dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add iwl_fw_ini_region_cfg region struct to fill_header handler of
iwl_dump_ini_mem_ops. it is needed for future support in fifos dumping.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Make fill_range handler of iwl_dump_ini_mem_ops accept a generic range
pointer. It is needed for future support in fifos dumping.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Make the get size handler of iwl_dump_ini_mem_ops include the total
size of the region. It is needed for fifos dumping.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add informative print in case the range is not available.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The driver sets ignore_consec to -1 which is 0xffffffff in u32
so when iwl_fw_ini_trigger_on is called, it will always return false
and each trigger could be used only once.
Solve this by removing the assignment to -1.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: fe1b7d6c2888 ("iwlwifi: add support for triggering ini triggers")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This helps debugging when things go wrong.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
After the FW image was loaded for the first time,
fwrt->smem_cfg.num_lmacs value will no longer be zero since we don't
clean it when we stop the device. So if we load the image once and then
we fail on a consecutive attempt, the driver will abort any dumping.
Solve this by removing the condition. It is safe to remove since
when we do the actual dumping in iwl_fw_dbg_collect_sync we check
that STATUS_DEVICE_ENABLED bit is still active.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For non-offloaded rate control, implement VHT extended NSS
support by just ignoring 160 MHz on transmit if the peer
doesn't support the full NSS (2). This is pretty unlikely
and gets us 160 MHz RX as well as TX in most cases, since
the typical case for this workaround is 4x4 AP only doing
2x2 on 160 MHz.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When hostapd sends a probe response, it does not request an
acknowledgment on the probe response. This setting is propagated
to the driver and FW from mac80211, and as a result probe responses
are transmitted only once without retries. In congested
environments, this reduces the likelihood for finding the AP.
To overcome this, enable acknowledgment and retries for probe
responses, even in case no acknowledgment is requested. In such
a case the retry limit is set to 3.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no point in this, we already do everything in a nested
fashion, and if we didn't we'd already crash in iwl_mvm_leds_exit()
etc. Just remove the bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Previously the protection flag wasn't set on multicast frames even if
the RA is unicast. Fix this by checking addr1 instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add an option to not send beacons and probe responses. This is
used for testing multiple-bssid.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Return the AID currently set when reading this debugfs entry.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Verify we do not accept new beacon templates while beacon
injection is active.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We support this, so we should advertise it. In fact, if we don't,
mac80211 will do it for us (as we advertise SUPPORTS_VHT_EXT_NSS_BW
to it), but that requires a memory reallocation which is wasteful:
ieee80211 phy0: copying sband (band 1) due to VHT EXT NSS BW flag
Set the flag here to avoid that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The IWL_MVM_INIT_STATUS_REG_HW_INIT_COMPLETE bit shouldn't be set,
and realistically we should complete all setup before we call the
ieee80211_register_hw() function. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
With CONFIG_NO_AUTO_INLINE, we run into a silly warning when
gcc fails to remember that n_profiles is constant across
the function call to iwl_mvm_sar_set_profile:
drivers/net/wireless/intel/iwlwifi/mvm/fw.c: In function 'iwl_mvm_sar_get_ewrd_table':
drivers/net/wireless/intel/iwlwifi/mvm/fw.c:746:9: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Marking that function 'inline' avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In case mac80211 was requested to perform an HW restart, but the HW
restart has not started yet, there is no need to request another one.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
AX210 devices assume that the (DRAM) addresses of the rb_stts's for
the different queues are continuous.
So allocate the rb_stts's for all the Rx queues in one place.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
ath.git patches for 5.1. Major changes:
ath10k
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having
WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
|
|
The start() callback is too late for this: NetworkManager would already
have seen the hardware, thinking 00:00:00:00:00:00 is its permanent
address.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In order to be able to get a MAC address before we register the device
with ieee80211 we'll need to load the firmware way earlier.
There seems to be one problem with this: the device seems to start
with radio enabled and starts sending in frames right after the firmware
load finishes. Disable the radio as soon as possible.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We'll need to talk to the firmware to get a hardware address before
device is registered with ieee80211 subsystem at the end of
lbtf_add_card(). Hooking the callbacks after that is too late.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
While experimenting with firmware loading I ended up in a state of
firmware reporting shared RAM address 0x04000001. It was causing:
[ 94.448015] Unable to handle kernel paging request at virtual address cd680001
due to reading out of the mapped memory.
This patch adds some basic validation to avoid kernel crashes due to the
unexpected firmware behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
Lorenzo Bianconi
Stanislaw Gruszka
Felix Fietkau
David S. Miller
Johannes Berg
Liad Kaufman
Li RongQing
Ihab Zhaika
Shahar S Matityahu
Sara Sharon
Ilan Peer
Andrei Otcheretianski
Greg Kroah-Hartman
Gustavo A. R. Silva
Arnd Bergmann
Triebitz
Kalle Valo
Lubomir Rintel
Rafał Miłecki