| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In the major update of the rtlwifi-family of drivers, there was an editing
mistake. Unfortunately, this particular error leads to memory corruption that
silently leads to failure of the system. This patch is one of three needed to
fix the kernel regression reported at https://bugzilla.kernel.org/show_bug.cgi?id=88951.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Catalin Iacob <iacobcatalin@gmail.com>
Tested-by: Catalin Iacob <iacobcatalin@gmail.com>
Cc: Catalin Iacob <iacobcatalin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Adds all FH registers between FH_MEM_UPPER_BOUND and
FH_MEM_LOWER_BOUND (which should be readable to the driver)
to the dump data when it is collected.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The ucode load flow changed for B0 hardware step.
Change the code accordingly.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Not doing so would allow other possible users of the device
to take ownership and prevent normal WiFi operation.
This fixes the second part of:
https://bugzilla.kernel.org/show_bug.cgi?id=87191
Reviewed-by: Moshe Harel <moshe.harel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
7265D are new devices that should always have a new NVM
(at least 0x0c11). The firmware has issues with older
versions of the NVM which are not and will not be available
to the common mortals.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Handle NVM file header. When NVM header detected, skip
the header and reading only the sections data.
Signed-off-by: Idan Kahlon <idanx.kahlon@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add the channels on which there was a match for every match reported
by the firmware. The firmware reports the channels as indices to the
array of channels that was passed in the scheduled scan request, so we
need to save the array when entering D3 to make sure it is available
when we resume.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add SSID information to the net-detect indication to userspace. Fetch
the matched profiles from the firmware in order to find the correct
SSIDs in the profiles that matched.
Since the net-detect information is stored in cfg80211, and in theory
it could change while we are waking up and reading the matched
profiles, we need to save it when we enter D3 so it is available
during resume.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
A following patche will use trans_pcie->cmd_in_flight
for reference accounting as well. get ready for it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
IWL_MVM_REF_PROTECT_CSA is missing from the ref strings
used by debugfs.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This impacts the partition between BT and Wifi.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
All the supported firmwares have this TLV flag set.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
All the supported firmwares have this TLV flag set.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This TLV flag is set for all the supported firmwares.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This firmware is not supported anymore.
Stop loading this firmware - and remove the code that
handled older versions.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Query the firmware for scan offload matches when waking up in order to
report net detect as the reason for the wake up.
This requires a new command API to be implemented. Additionally,
remove some net detect command entries that are not valid anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The firmware file-format is described in iwl-fw-file.h, while the
internal handling structures and functions are in iwl-fw.h.
Fix the separation between the files by moving file format
definitions to iwl-fw-file.h.
Also add a missing description for a kernel-doc member, and it's
not needed to include iwl-fw-file.h again from the code (thanks
to Liad Kaufman).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Don't bother with fancy arithmetic and just
hardcode the final values.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In theory it was possible to starve the system if
a tx/rx handler could implicitly trigger more
tx/rx pci events.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Pass the eid argument via skbuff control buffer.
This will make it possible to work with queues of
HTC event buffers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This wasn't used since forever and there are no
plans on using it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The service bitmap can be used to determine
firmware capabilities.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This shouldn't really happen but take into account
the original service bitmap length when mapping
service ids.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The dump print uses sizeof() but since service_map
was a mere pointer the dump was too short.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Traces shouldn't modified passed data. This will
make it possible to pass const arguments to
traces.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Increase the rts threshold from the legacy value of 2347 to support higher
threshold limit.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.
Move the event to its own function call internally and to
its own event attribute in nl80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The number of peers isn't directly translatable to
the number of stations because ath10k needs to
reserve a few extra peers for special cases like
multi-vif concurrency.
The previous limit was 126 and 15 stations in AP
mode for 10.x and main firmware branches
respectively. The limit is now 128 and 16 which
was the original intention.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The var was supposed to be protected by data_lock
but it wasn't so in all instances. It's actually
not necessary to have a spinlock protected
num_peers so drop it.
All instances of num_peers are already within
conf_mutex sections so use that.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This prevents warning spamming if peer creation
fails during sta_state in some cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add mem_val debugfs file for dumping the firmware (target) memory and also for
writing to the memory. The firmware memory is accessed through one file which
uses position of the file as the firmware memory address. For example, with dd
use skip parameter for the address.
Beucase target memory width is 32 bits it's strongly recommended to use
blocksize divisable with 4 when using this interface. For example, when using
dd use bs=4 to set the block size to 4 and remember to divide both count and
skip values with four.
To read 4 kB chunk from address 0x400000:
dd if=mem_value bs=4 count=1024 skip=1048576 | xxd -g1
To write value 0x01020304 to address 0x400400:
echo 0x01020304 | xxd -r | dd of=mem_value bs=4 seek=1048832
To read 4 KB chunk of memory and then write back after edit:
dd if=mem_value of=tmp.bin bs=4 count=1024 skip=1048576
emacs tmp.bin
dd if=tmp.bin of=mem_value bs=4 count=1024 seek=1048576
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Debugfs files reg_addr and reg_val are used for reading and writing to the
firmware (target) registers. reg_addr contains the address to be accessed,
which also needs to be set first, and reg_value is when used for reading and
writing the actual value in ASCII.
To read a value from the firmware register 0x100000:
# echo 0x100000 > reg_addr
# cat reg_value
0x00100000:0x000002d3
To write value 0x2400 to address 0x100000:
# echo 0x100000 > reg_addr
# echo 0x2400 > reg_value
#
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
ath10k_tx_wep_key_work() acquires conf_mutex, so
cancelling it when conf_mutex is already taken
in ath10k_remove_interface() is incorrect, so
move it outside the lock.
Snippet from the lockdep report:
kernel: ======================================================
kernel: [ INFO: possible circular locking dependency detected ]
kernel: 3.18.0-rc5-wl-debug #34 Tainted: G O
kernel: -------------------------------------------------------
kernel: hostapd/451 is trying to acquire lock:
kernel: ((&arvif->wep_key_work)){+.+...}, at: [<ffffffff810872d5>] flush_work+0x5/0x290
kernel: but task is already holding lock:
kernel: (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa0b99f00>] ath10k_remove_interface+0x40/0x290 [ath10k_core]
kernel: which lock already depends on the new lock.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
peer->keys needs to be protected by data_lock
since it is also accessed from the WMI path.
Both install() and clear() routines for peer
keys modify the key contents, so use the data_lock
to avoid races.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When static keys are used in shared WEP, when a
station is associated, message 3 is sent with an
encrypted payload. But, for subsequent
authentications that are triggered without a
deauth, the auth frame is decrypted by the HW.
To handle this, check if the WEP keys have already
been set for the peer and if so, mark the
frame as decrypted. This scenario can happen
when a station changes its default TX key and initiates
a new authentication sequence.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Some firmware revisions don't seem to deilver
management frames with FCS error via WMI so narrow
down the HTT rule to not drop corrupted management
frames.
This basically increases number of frames ath10k
reports while sniffing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When mac80211 requests driver to cancel a hw roc
the driver must not call the expired() callback or
else roc will fail in some cases depending on how
things get scheduled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
With P2P concurrency requested hw roc duration
time can be very small. Some firmware revisions
refuse scan requests with too small channel dwell
time.
This prevents messages like, e.g. with connected
STA vif and performing P2P Find:
ath10k_pci 0000:00:05.0: failed to switch to channel for roc scan
ieee80211 phy3: failed to start next HW ROC (-110)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New firmware revisions don't need peer creation
when doing offchannel tx. Earlier revisions would
queue and never release frames without a peer.
This prevent new firmware revisions from stopping
replenishing wmi-htc tx credits and improves
reliability of offchannel tx which would sometimes
silently fail.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Comment was out-of-date. The headroom is no longer
necessary because HTT Tx fragment list is stored
in dma pool item associated with each sk_buff.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When re-associating a station, the nss was set back to
maximum value even if user had configured small number
of tx chains. So, pay attention to user's config in
this case as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It appears it takes more than just setting the
hardware's chainmask to make things work well. Without
this patch, a vdev would only use 1x1 rates when chainmask
was set to 0x3.
Setting the 'nss' (number of spatial streams) on the vdev
helps the firmware's rate-control algorithm work properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The existing order of steps when starting the PCI devices works for
2.4G devices, but fails to initialize the 5G section of the RTL8821AE
hardware.
This patch is needed to fix the regression reported in Bug #88811
(https://bugzilla.kernel.org/show_bug.cgi?id=88811).
Reported-by: Valerio Passini <valerio.passini@unicam.it>
Tested-by: Valerio Passini <valerio.passini@unicam.it>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Valerio Passini <valerio.passini@unicam.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The changes associated with moving this driver from staging to the regular
tree missed one section setting the allowable rates for the 5GHz band.
This patch is needed to fix the regression reported in Bug #88811
(https://bugzilla.kernel.org/show_bug.cgi?id=88811).
Reported-by: Valerio Passini <valerio.passini@unicam.it>
Tested-by: Valerio Passini <valerio.passini@unicam.it>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Valerio Passini <valerio.passini@unicam.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ACK status (0/1) for ACTION frames is informed to cfg80211. We
will extend existing logic used for EAPOL frames. The cfg80211
API is different here. Also, we need to explicitly free cloned
skb.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Firmware notifies the driver through event if EAPOL data packet
has been acked or not. We will inform this status to userspace
listening on a socket.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We had introduced delay main work logic to avoid processing
interrupts when Rx pending packet count reaches high threshold.
interrupt processing is restarted later when packet count
reduces lower threashold. This helped to reduce unnecessary
overhead and improve throughput for SD and PCIe chipsets.
As there are no interrupts for USB, we will skip this logic for
USB chipsets.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds missing endian conversion for beacon size while
processing scan response.
Reported-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Tested-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes following sparse warnings:
drivers/net/wireless/mwifiex/util.c:152:19: warning: cast from restricted __le16
drivers/net/wireless/mwifiex/util.c:152:19: warning: restricted __le16 degrades to integer
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
Larry Finger
Liad Kaufman
Eran Harary
David Spinadel
Emmanuel Grumbach
Idan Kahlon
Luciano Coelho
Eliad Peller
Johannes Berg
Michal Kazior
Vivek Natarajan
Yanbo Li
Sujith Manoharan
Ben Greear
Amitkumar Karwar