| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This reverts commit 6301566e0b2dafa7d6779598621bca867962a0a2. Oleksij Rempel
noticed that the randomness doesn't look to be good enough and Stephan Mueller
commented:
"I would say that the discussed RNG does not seem fit for hooking it up with the
hwrandom framework."
http://lkml.kernel.org/g/3945775.m5HblJPgiO@tauon.atsec.com
So let's the revert the patch until we are sure that we can trust this random
generator.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In commit 33511b157bbcebaef853cc1811992b664a2e5862 ("rtlwifi: add support to
send beacon frame"), the mechanism for sending beacons was established. That
patch works correctly for rtl8192cu, but there is a possibility of getting
the following warnings in the PCI drivers:
WARNING: CPU: 1 PID: 2439 at net/mac80211/driver-ops.h:12
ieee80211_bss_info_change_notify+0x179/0x1d0 [mac80211]()
wlp5s0: Failed check-sdata-in-driver check, flags: 0x0
The warning is followed by a NULL pointer dereference as follows:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000006
IP: [<ffffffffc073998e>] rtl_get_tcb_desc+0x5e/0x760 [rtlwifi]
This problem was reported at http://thread.gmane.org/gmane.linux.kernel.wireless.general/138645,
but no solution was found at that time.
The problem was also reported at https://bugzilla.kernel.org/show_bug.cgi?id=9744
and this solution was developed and tested there.
The USB driver works with a NULL final argument in the adapter_tx() callback;
however, the PCI drivers need a struct rtl_tcb_desc in that position.
Fixes: 33511b157bbc ("rtlwifi: add support to send beacon frame.")
Signed-off-by: Luis Felipe Dominguez Vega <lfdominguez@nauta.cu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.19+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
On the 2GHz and and on the 5GHZ band only the extpa_gain setting from
the 5GHz band was checked. this patch makes it check the property from
the correct band.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes commit eae79b4f3e82 ("rsi: fix memory leak in rsi_load_ta_instructions()")
which stopped the driver from functioning.
Firmware data has been allocated using vmalloc(), resulting in memory
that cannot be used for DMA. Hence the firmware was first copied to a
buffer allocated with kmalloc() in the original code. This patch reverts
the commit and only calls "kfree()" to release the buffer after sending
the data. This fixes the memory leak without breaking the driver.
Add a comment to the kmemdup() calls to explain why this is done, and abort
if memory allocation fails.
Tested on a Topic Miami-Florida board which contains the rsi SDIO chip.
Also added the same kfree() call to the USB glue driver. This was not
tested on actual hardware though, as I only have the SDIO version.
Fixes: eae79b4f3e82 ("rsi: fix memory leak in rsi_load_ta_instructions()")
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
* a fix for the stuck TFD queue mechanism - it was producing
noisy false alarms.
* a fix for the NIC prepare flow that prevented the driver
from being able to access the device on certain systems.
* a fix for the scan prority handling which allows the
regular scan to run even if a scheduled scan is already
running.
|
|
The stuck queue detection mechanism allows to detect queues
that are stuck. For sleeping clients, a queue may rightfully
be stuck: if a poor client implementation stays asleep for
more than 10s, then we don't want to trigger recovery flows
because of that client.
In order to cope with this, I added a mechanism that
monitors the state of the client: when a client goes to
sleep, the timer of his queues is frozen. When he wakes up,
the timer is reset to the right value so that if a client
was awake for more than 10s and the queues are stuck, only
then, the recovery flow will kick in.
This is valid only on non-shared queues: A-MPDU queues.
There was a bug in case we Tx to a sleeping client that has
an empty A-MPDU queue: the timer was armed to now + 10s.
This is bad, but pretty harmless.
The problem is that when the client wakes up, the timer is
modified to be now + remainder. But remainder is 0 since the
queue was empty when that client went to sleep...
Fix this by checking the state of the client before playing
with the timer when we add a packet to an empty queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Initial QCA99X0 support has a known issue with TCP Tx throughput.
All other path such as UDP Tx/Rx and TCP Rx meet their expectation
(> 900Mbps), but TCP Tx marked as low as 5Mbps when single pair is
used on iperf.
The root cause is turned out because TSO flag is not initialized
properly so that firmware configures TSO in wrong way.
TSO flags in msdu extension descriptor is required to be reset
to indicate firmware there is no TSO is enabled, otherwise it
could act as TSO is enabled which causes huge throughput drop.
In fact, it's enough by resetting TSO flags only to prevent the
unexpected behavior, but initializing whole msdu ext. descriptor
will help to clear uncertainty of firmware could bring on as it
constantly updated.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add vendor/device id of QCA99X0 V2.0 to pci id table and
QCA99X0_HW_2_0_CHIP_ID_REV to ath10k_pci_supp_chips[] for
QCA99X0 to get detected by the driver.
kvalo: now QCA99X0 family of chipsets is supported by ath10k.
Tested client, AP and monitor mode with QCA9990.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When max client was set to 512 in qca99x0, there was host memory
alloc failure during wmi service ready event handling. This issue
got resolved now, increasing max client limit from 256 to 512.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Host memory required for firmware is allocated while handling
wmi service ready event. Right now, wmi service ready is handled
in tasklet context and it calls dma_alloc_coherent() with atomic
flag (GFP_ATOMIC) to allocate memory in host needed for firmware.
The problem is, dma_alloc_coherent() with GFP_ATOMIC fails in
the platform (at least in AP platform) where it has less atomic
pool memory (< 2mb). QCA99X0 requires around 2 MB of host memory
for one card, having additional QCA99X0 card in the same platform
will require similarly amount of memory. So, it's not guaranteed that
all the platform will have enough atomic memory pool.
Fix this issue, by handling wmi service ready event in workqueue
context and calling dma_alloc_coherent() with GFP_KERNEL. mac80211 work
queue will not be ready at the time of handling wmi service ready.
So, it can't be used to handle wmi service ready. Also, register work
gets scheduled during insmod in existing ath10k_wq and waits for
wmi service ready to completed. Both workqueue can't be used for
this purpose. New auxiliary workqueue is added to handle wmi service
ready.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This patch enables raw Rx/Tx encap mode to support software based
crypto engine. This patch introduces a new module param 'cryptmode'.
cryptmode:
0: Use hardware crypto engine globally with native Wi-Fi mode TX/RX
encapsulation to the firmware. This is the default mode.
1: Use sofware crypto engine globally with raw mode TX/RX
encapsulation to the firmware.
Known limitation:
A-MSDU must be disabled for RAW Tx encap mode to perform well when
heavy traffic is applied.
Testing: (by Michal Kazior <michal.kazior@tieto.com>)
a) Performance Testing
cryptmode=1
ap=qca988x sta=killer1525
killer1525 -> qca988x 194.496 mbps [tcp1 ip4]
killer1525 -> qca988x 238.309 mbps [tcp5 ip4]
killer1525 -> qca988x 266.958 mbps [udp1 ip4]
killer1525 -> qca988x 477.468 mbps [udp5 ip4]
qca988x -> killer1525 301.378 mbps [tcp1 ip4]
qca988x -> killer1525 297.949 mbps [tcp5 ip4]
qca988x -> killer1525 331.351 mbps [udp1 ip4]
qca988x -> killer1525 371.528 mbps [udp5 ip4]
ap=killer1525 sta=qca988x
qca988x -> killer1525 331.447 mbps [tcp1 ip4]
qca988x -> killer1525 328.783 mbps [tcp5 ip4]
qca988x -> killer1525 375.309 mbps [udp1 ip4]
qca988x -> killer1525 403.379 mbps [udp5 ip4]
killer1525 -> qca988x 203.689 mbps [tcp1 ip4]
killer1525 -> qca988x 222.339 mbps [tcp5 ip4]
killer1525 -> qca988x 264.199 mbps [udp1 ip4]
killer1525 -> qca988x 479.371 mbps [udp5 ip4]
Note:
- only open network tested for RAW vs nwifi performance comparison
- killer1525 (qca6174 hw2.2) is 2x2 device (hence max 866mbps)
- used iperf
- OTA, devices a few cm apart from each other, no shielding
- tcpX/udpX, X - means number of threads used
Overview:
- relative Tx performance drop is seen but is within reasonable and
expected threshold (A-MSDU must be disabled with RAW Tx)
b) Connectivity Testing
cryptmode=1
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
Note:
- each test takes all possible endpoint pairs and pings
- each pair-ping flushes arp table
- ip6 is used
c) Testbed Topology:
1ap1sta:
[ap] ---- [sta]
endpoints: ap, sta
1ap1sta2br:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
endpoints: veth0, veth2, br0, br1
note: STA works in 4addr mode, AP has wds_sta=1
1ap1sta2br1vlan:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
| |
[vlan0_id2] [vlan1_id2]
endpoints: vlan0_id2, vlan1_id2
note: STA works in 4addr mode, AP has wds_sta=1
Credits:
Thanks to Michal Kazior <michal.kazior@tieto.com> who helped find the
amsdu issue, contributed a workaround (already squashed into this
patch), and contributed the throughput and connectivity tests results.
Signed-off-by: David Liu <cfliu.tw@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Tested-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
During tx completion, tx_lock is held for longer than required, preventing
efficient refill of htt->pending_tx. Refactor the code so that only MSDU
related operations are protected by the lock.
Improves downstream performance on a dual-core ARM Freescale LS1024A
(f.k.a. Mindspeed Comcerto 2000) AP with a 3x3 client from 495 to 580 Mbps.
Other CPU bound multicore systems may also benefit.
Signed-off-by: Denton Gentry <dgentry@google.com>
Signed-off-by: Avery Pennarun <apenwarr@google.com>
[mfaltesek@google.com: removed conflicting code for tracking msdu_ids.]
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When using DFS channels on Ath10k, kernel log has repeated warning message
'failed to process fft: -22' typically under medium/heavy traffic.
This patch switches the warnings to driver debug (WMI events) mode only
thus reducing log file noise.
DFS and spectral scan share underlying HW mechanisms and enabling one
(DFS) enables the other (spectral scan) as far as event reporting from
firmware to driver is concerned. Spectral scan events take no part in
processing of DFS radar pulses which are delivered as distinct events,
so the fft (spectral event) warning is harmless and DFS interference
detection/protection still occurs.
Symptoms seen & fix tested in both debug & non-debug modes on TP-Link
Archer C7 v2 platform.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This fixes two misspellings of "distribution" in a comment.
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The code checks the total number of iterations to differentiate
between regular scan and scheduled scan. However, regular scan has
a total of one iteration, not zero. As a result, regular scan will
have lower priority than it should have, and in case scheduled
scan is already running when regular scan is requested, regular scan
will be delayed until scheduled scan is aborted.
Fix that by checking for total iterations number of one as an
identifier for regular scan.
Fixes: 133c8259f885 ("iwlwifi: mvm: rename generic_scan_cmd functions to dwell")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When the card is not owned by the PCIe bus, we need to
acquire ownership first. This flow is implemented in
iwl_pcie_prepare_card_hw. Because of a hardware bug, we
need to disable link power management before we can
request ownership otherwise the other user of the device
won't get notified that we are requesting the device which
will prevent us from acquire ownership.
Same holds for the down flow where we need to make sure
that any other potential user is notified that the driver
is going down.
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
HTT_H2T_MSG_TYPE_MGMT_TX msg in 10.4 firmware carries additional
4 byte in htt_mgmt_tx_desc where it tells to firmware that at what
rate mgmt frame has to go out in the air. It's an optional parameter,
setting this field to zero will force firmware to choose auto rate
and send the frame out.
Those 4 byte info is missed out in the current code and 10.4 firmware
ended up reading some junk in those 4 byte and sometime malfunctioning.
Fix it by adding 4 byte in struct htt_mgmt_tx_desc. Non 10.4 firmware
will not process those four byte. So, adding 4 byte at the end of
struct htt_mgmt_tx_desc will not create any impact on other chipset.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The patch adds support to offload TCP/UDP checksum
calculations for QCA99x0.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
chandef is initialized with NULL and on the very next line, we are using it to
get channel, which is not correct. Channel should be initialized after
obtaining chandef.
Found by cppcheck:
ath/ath10k/mac.c:839]: (error) Possible null pointer dereference: chandef
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
QCA99X0 chip has an extra 4 bytes in rx_msdu_start,
20 bytes in rx_msdu_end and 20 bytes in rx_ppdu_end structure
which are used in htt_rx_desc and HTT Rx ring offset setup.
This is necessary for correct Rx for QCA99X0 or Rx descriptors
will be overwritten and corrupted.
With this patch QCA988X and QCA6174 will have extra 44 bytes
padding in Rx descriptor layout which is harmless.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
rx_ppdu_end_common structure is valid for both of qca998x and
qca6174, but not for qca99x0 since it has new additional members.
Hence update the common structure to cover qca99x0 as well.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Since QCA99X0 uses fragmentation descriptor differently from
other ones on tx path, we need to handle it separately.
QCA99X0 is using 48 bits for address and 16 bits for length
out of 2 dword and each values have to be programmed by frag
desc base addr + msdu id, so that hardware can retrieve
corresponding frag data.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It is observed that during cold reset pcie access right
after a write operation to SOC_GLOBAL_RESET_ADDRESS causes
Data Bus Error and system hard lockup. The reason
for bus error is that pcie needs some time to get
back to stable state for any transaction during cold reset. Add
delay of 20 msecs after write of SOC_GLOBAL_RESET_ADDRESS
to fix this issue. This patch is tested on QCA988X. This is
also tested on QCA99X0 which is WIP.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
While changing interface type from p2p client or p2p go to
station, we should update counters for p2p interface and
station interface. Also calling mwifiex_cfg80211_deinit_p2p
method instead of mwifiex_cfg80211_init_p2p_client method to
deinit p2p interface.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
0xfe is basically a magic number used to ask firmware match
provided string in a SSID. In this case, firmware will
return scan results containing"DIRECT-" string.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We are setting BSS mode as ANY so that firmware will provide
all types of scan entries.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There is no need to use hex_dump_to_buffer() in the cases like this:
hexdump_to_buffer(buf, len, 16, 1, outbuf, outlen, false); /* len <= 16 */
sprintf("%s\n", outbuf);
since it maybe easily converted to simple:
sprintf("%*ph\n", len, buf);
Note: it seems in the case the output is groupped by 2 bytes and looks like a
typo. Thus, patch changes that to plain byte stream.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
update the rssi reading on rx_status
to read both RSSI level (7 bits) and
antenna diversity (msb)
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We measured the FFT-based entropy in 3 ways, Shannon entropy,
collision entropy, and directly measured min-entropy. Just to
be conservative, we recommend the estimated min-Entropy to be
10 bits per 16-bit value.
Analysis was done by Jacobson,David(djacobso@qti.qualcomm.com).
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Broadcom's firmware requires every BSS to use MAC address with unique
last few bits. The amount of bits may depend on a particular firmware,
it was verified to be 2 for BCM43602 one.
If this condition won't be fulfilled firmware will reject such MAC:
brcmfmac: _brcmf_set_mac_address: Setting cur_etheraddr failed, -52
We don't want to simply set addr_mask as it would also disallow using
locally administrated bit. Instead let's build a list of addresses
manually enabling 0x2 bit for extra interfaces.
Signed-off-by: Rafa? Mi?ecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
While compiling ath9k with some extra flags I've
found that:
ath9k/xmit.c +2473 ## 16: warning: restricted __le16 degrades to integer
ath9k/xmit.c +2474 ## 36: warning: invalid assignment: &=
ath9k/xmit.c +2474 ## 36: left side has type restricted __le16
ath9k/xmit.c +2474 ## 36: right side has type int
There's no way for frame ftype/stype to be
mistreated as the offending 'moredata' flag when
considering cab queue.
This could've however theoretically led sometimes
to increased power consumption on connected
stations as they would keep their Rx active
waiting for frames that would never come.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Replace a kmalloc+strcpy by an equivalent kstrdup in order to improve
readability.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In routine _rtl8821ae_set_media_status(), an incorrect mask results in a test
for AP status to always be false. Similar bugs were fixed in rtl8192cu and
rtl8192de, but this instance was missed at that time.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch fixes following issues in p2p code paths.
1) bss role, bss type and connection type was not set correctly
for p2p GO and p2p client at couple of places.
2) Driver appends a proprietary header to management frames
which will be parsed by our firmware. Later while informing
TX status to cfg80211, modified frame buffer was passed to
cfg80211_mgmt_tx_status() instead of original one.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
A long time ago, ath9k had issues during reset where the DMA engine
would stay active and could potentially corrupt memory.
To debug those issues, the driver would print warnings whenever they
occur.
Nowadays, these issues are gone and the primary cause of these messages
is if the MAC is stuck during reset or busy processing a long
transmission. This is fairly harmless, yet these messages continue to
worry users.
To reduce the number of bogus bug reports, turn these messages into
debug messages and count their occurence in the "reset" debugfs file.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When wlcore_probe_of failed, return the correct error code instead of ENOMEM
Signed-off-by: Raphaël Poggi <poggi.raph@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This fixes a typo in the "b43_lo_g_maintenance_work" function
name.
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This fixes a typo in two comments: "paht" -> "path".
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There is an error that can occur where the driver adds the same URB to USB submission list twice.
This happens since mwifiex_usb_submit_rem_rx can submit packets at same time as an rx urb complete callback.
This causes list corruption and is fixed by not setting the skb to NULL when submitting an rx packet.
[ 84.461242] WARNING: CPU: 1 PID: 748 at lib/list_debug.c:36 __list_add+0xcb/0xd0()
[ 84.461245] list_add double add: new=ffff8800c92b0c50, prev=ffff8800c92b0c50, next=ffff8800ced6c430.
[ 84.461247] Modules linked in: rfcomm fuse cmac nf_conntrack_netbios_ns nf_conntrack_broadcast ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack bnep iptable_mangle iptable_security iptable_raw btusb btintel bluetooth mwifiex_usb mwifiex x86_pkg_temp_thermal cfg80211 coretemp r8712u(C) kvm_intel kvm hid_sensor_als hid_sensor_incl_3d hid_sensor_rotation hid_sensor_magn_3d hid_sensor_accel_3d hid_sensor_gyro_3d hid_sensor_trigger hid_sensor_iio_common industrialio_triggered_buffer kfifo_buf rfkill iTCO_wdt industrialio iTCO_vendor_support
[ 84.461316] crc32_pclmul crc32c_intel ghash_clmulni_intel microcode snd_hda_codec_realtek vfat snd_hda_codec_generic fat snd_hda_codec_hdmi snd_hda_intel snd_hda_controller uvcvideo snd_hda_codec videobuf2_vmalloc videobuf2_memops snd_hwdep videobuf2_core snd_hda_core joydev v4l2_common videodev hid_sensor_hub snd_seq hid_multitouch media snd_seq_device snd_pcm snd_timer mei_me snd i2c_i801 lpc_ich mei soundcore tpm_infineon tpm_tis tpm i2c_hid i2c_designware_platform i2c_designware_core nfsd auth_rpcgss nfs_acl lockd grace sunrpc sch_fq_codel i915 i2c_algo_bit drm_kms_helper drm xhci_pci xhci_hcd ehci_pci sd_mod ehci_hcd video
[ 84.461383] CPU: 1 PID: 748 Comm: kworker/u9:0 Tainted: G C 4.1.0-rc5+ #163
[ 84.461386] Hardware name: Microsoft Corporation Surface Pro 2/Surface Pro 2, BIOS 2.05.0250 04/10/2015
[ 84.461396] Workqueue: MWIFIEX_RX_WORK_QUEUE mwifiex_rx_work_queue [mwifiex]
[ 84.461399] ffffffff81a8150e ffff8801174cf8e8 ffffffff817df830 0000000000000000
[ 84.461405] ffff8801174cf938 ffff8801174cf928 ffffffff810a54ba ffff8800c86bd750
[ 84.461410] ffff8800c92b0c50 ffff8800c92b0c50 ffff8800ced6c430 ffff88010c057178
[ 84.461416] Call Trace:
[ 84.461421] [<ffffffff817df830>] dump_stack+0x4f/0x7b
[ 84.461428] [<ffffffff810a54ba>] warn_slowpath_common+0x8a/0xc0
[ 84.461432] [<ffffffff810a5536>] warn_slowpath_fmt+0x46/0x50
[ 84.461436] [<ffffffff814109fb>] __list_add+0xcb/0xd0
[ 84.461442] [<ffffffff815c551a>] ? usb_hcd_link_urb_to_ep+0x2a/0xa0
[ 84.461446] [<ffffffff815c5570>] usb_hcd_link_urb_to_ep+0x80/0xa0
[ 84.461459] [<ffffffffa004318a>] prepare_transfer+0xaa/0x130 [xhci_hcd]
[ 84.461470] [<ffffffffa0044cf7>] xhci_queue_bulk_tx+0xb7/0x7a0 [xhci_hcd]
[ 84.461480] [<ffffffffa003b67f>] ? xhci_urb_enqueue+0x50f/0x660 [xhci_hcd]
[ 84.461489] [<ffffffffa003b67f>] ? xhci_urb_enqueue+0x50f/0x660 [xhci_hcd]
[ 84.461498] [<ffffffffa003b735>] xhci_urb_enqueue+0x5c5/0x660 [xhci_hcd]
[ 84.461503] [<ffffffff815c7ad3>] usb_hcd_submit_urb+0x93/0xa70
[ 84.461507] [<ffffffff8168dde8>] ? __alloc_skb+0x78/0x1f0
[ 84.461511] [<ffffffff8168d301>] ? __kmalloc_reserve.isra.26+0x31/0x90
[ 84.461515] [<ffffffff8168ddbc>] ? __alloc_skb+0x4c/0x1f0
[ 84.461519] [<ffffffff8168ddfc>] ? __alloc_skb+0x8c/0x1f0
[ 84.461523] [<ffffffff8168badd>] ? skb_dequeue+0x5d/0x80
[ 84.461527] [<ffffffff815c987e>] usb_submit_urb+0x42e/0x5f0
[ 84.461531] [<ffffffff816931d9>] ? __alloc_rx_skb+0x39/0x100
[ 84.461536] [<ffffffffa05aa372>] mwifiex_usb_submit_rx_urb+0xb2/0x170 [mwifiex_usb]
[ 84.461542] [<ffffffffa05aa5f5>] mwifiex_usb_submit_rem_rx_urbs+0x45/0x50 [mwifiex_usb]
[ 84.461550] [<ffffffffa07094be>] mwifiex_rx_work_queue+0x10e/0x140 [mwifiex]
[ 84.461556] [<ffffffff810c4429>] process_one_work+0x229/0x890
[ 84.461559] [<ffffffff810c438c>] ? process_one_work+0x18c/0x890
[ 84.461565] [<ffffffff810c4ae3>] worker_thread+0x53/0x470
[ 84.461569] [<ffffffff810c4a90>] ? process_one_work+0x890/0x890
[ 84.461572] [<ffffffff810cb162>] kthread+0xf2/0x110
[ 84.461577] [<ffffffff811031ad>] ? trace_hardirqs_on+0xd/0x10
[ 84.461581] [<ffffffff810cb070>] ? kthread_create_on_node+0x230/0x230
[ 84.461586] [<ffffffff817e9662>] ret_from_fork+0x42/0x70
[ 84.461590] [<ffffffff810cb070>] ? kthread_create_on_node+0x230/0x230
[ 84.461593] ---[ end trace 65103af5e6fb3444 ]---
Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Storage pointed to by gen_ie is allocated with kmalloc, but was
never freed.
Coverity CID #1271251
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Without this change, the code simply exits after calling
mwifiex_uap_set_head_tail_ies, leving the call to
mwifiex_set_mgmt_beacon_data_ies as dead code.
Coverity CID #1271292
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
mwifiex_set_wowlan_mef_entry attempts to free a passed-in pointer in
case of an error. The only caller (mwifiex_set_mef_filter) passes that
pointer as an offset into allocated memory, so any attempt to free that
will not be the actual allocated pointer.
Address this by changing mwifiex_set_wowlan_mef_entry to not do any
free, and to cause mwifiex_set_mef_filter to do the appropriate free if
the call to mwifiex_set_wowlan_mef_entry fails.
Coverity CID #1295879
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In ancient times it was necessary to manually initialize the bus
field of an spi_driver to spi_bus_type. These days this is done in
spi_register_driver(), so we can drop the manual assignment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Solomon Peachy <pizza@shaftnet.org>
To: Kalle Valo <kvalo@codeaurora.org>
To: linux-wireless@vger.kernel.org
To: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds support to handle multichannel event from FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Multichannel and DFS cannot be supported at same time. So when multichannel
operation is enabled by module parameter, we enable number of channel as 2
while registering wiphy. For all other cases we advertise DFS support to
cfg80211. Patch also adds support for radar detect widths parameter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds support to advetise mwifiex multichannel support to
cfg80211. If module parameter drcs is enabled and FW supports multichannel
operation we advertise this support to cfg80211. As of now 2 simultaneous
channels are supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds support for setting multichannel policy as module parameter
to FW. Value of 1 indicates Multichannel support is enabled
and value of 0 disables it.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds support to extend TX Data pause for AP intefaces.
Also for station role, support for pausing/unpausing all traffic
when mac address parameter is BSSID is added.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds support to enable data traffic only when port is open.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
Kalle Valo
Luis Felipe Dominguez Vega
Hauke Mehrtens
Mike Looijmans
Emmanuel Grumbach
Peter Oh
Vasanthakumar Thiagarajan
Raja Mani
David Liu
Qi Zhou
Kevin Darbyshire-Bryant
Nik Nyby
Avraham Stern
Manikanta Pubbisetty
Maninder Singh
Aniket Nagarnaik
Andy Shevchenko
Guy Mishol
Miaoqing Pan
Rafa? Mi?ecki
Michal Kazior
Christophe Jaillet
Larry Finger
Felix Fietkau
Raphaël Poggi
Reyad Attiyat
John Linville
Antonio Borneo
Avinash Patil