| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As explained in the following commit a9a1a4833613 ("pinctrl:
armada-37xx: Fix gpio interrupt setup") the armada_37xx_irq_set_type()
function can be called before the initialization of the mask field.
That means that we can't use this field in this function and need to
workaround it using hwirq.
Fixes: 30ac0d3b0702 ("pinctrl: armada-37xx: Add edge both type gpio irq support")
Cc: stable@vger.kernel.org
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191115155752.2562-1-gregory.clement@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Intel Lightning Mountain SoC has a pinmux controller & GPIO controller IP which
controls pin multiplexing & configuration including GPIO functions selection &
GPIO attributes configuration.
This IP is not based on & does not have anything in common with Chassis
specification. The pinctrl drivers under pinctrl/intel/* are all based upon
Chassis spec compliant pinctrl IPs. So this driver doesn't fit & can not use
pinctrl framework under pinctrl/intel/* and it requires a separate new driver.
Add a new GPIO & pin control framework based driver for this IP.
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Link: https://lore.kernel.org/r/33e649758b70490f01724a887c490d5008c7656d.1573797249.git.rahul.tanwar@linux.intel.com
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Having static inline oneliner does not benefit too much when it is
only called from another oneliner function. Remove some of the
'onion'. This simplifies also the coming usage of the gpiolib
defines. We can do conversion from chip bits to gpiolib direction
defines as last step in the get_direction callback. Drivers can
use chip specific values in driver internal functions and do
conversion only once.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191113071045.GA22110@localhost.localdomain
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Meson A1 SoC share the same register layout of pinmux with previous
Meson-G12A, however there is difference for gpio and pin config register
in A1. The main difference is that registers before A1 are grouped by
function while those of A1 are by bank. The new register layout is as
below:
/* first bank */ /* addr */
- P_PADCTRL_GPIOP_I base + 0x00 << 2
- P_PADCTRL_GPIOP_O base + 0x01 << 2
- P_PADCTRL_GPIOP_OEN base + 0x02 << 2
- P_PADCTRL_GPIOP_PULL_EN base + 0x03 << 2
- P_PADCTRL_GPIOP_PULL_UP base + 0x04 << 2
- P_PADCTRL_GPIOP_DS base + 0x05 << 2
/* second bank */
- P_PADCTRL_GPIOB_I base + 0x10 << 2
- P_PADCTRL_GPIOB_O base + 0x11 << 2
- P_PADCTRL_GPIOB_OEN base + 0x12 << 2
- P_PADCTRL_GPIOB_PULL_EN base + 0x13 << 2
- P_PADCTRL_GPIOB_PULL_UP base + 0x14 << 2
- P_PADCTRL_GPIOB_DS base + 0x15 << 2
Each bank contains at least 6 registers to be configured, if one bank
has more than 16 gpios, an extra P_PADCTRL_GPIO[X]_DS_EXT is included.
Between two adjacent P_PADCTRL_GPIO[X]_I, there is an offset 0x10, that
is to say, for third bank, the offsets will be 0x20,0x21,0x22,0x23,0x24
,0x25 according to above register layout. For previous chips, registers
are grouped according to their functions while registers of A1 are
according to bank.Also note that there is no AO bank any more in A1.
Current Meson pinctrl driver can cover such change by using base address
of GPIO as that of drive-strength. While simply giving reg_ds = reg_pullen
make wrong value to reg_ds for Socs that do not support drive-strength
like AXG.To make things simple, add an extra dt parser function for
a1 and remain the old dt parser function for only reg parsing.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/1573819429-6937-3-git-send-email-qianggui.song@amlogic.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In meson_pinctrl_parse_dt, it contains two parts: reg parsing and
SoC relative fixup for AO. Several fixups in the same code make it hard
to maintain, so move all fixups to each SoC's callback and make
meson_pinctrl_parse_dt just do the reg parsing, separate these two
parts.Overview of all current Meson SoCs fixup is as below:
+------+--------------------------------------+--------------------------+
| | | |
| SoC | EE domain | AO domain |
+------+--------------------------------------+--------------------------+
|m8 | parse regs: | parse regs: |
|m8b | gpio,mux,pull,pull-enable(skip ds) | gpio,mux,pull(skip ds)|
|gxl | fixup: | fixup: |
|gxbb | no | pull-enable = pull; |
|axg | | |
+------+--------------------------------------+--------------------------+
|g12a | parse regs: | parse regs: |
|sm1 | gpio,mux,pull,pull-enable,ds | gpio,mux,ds |
| | fixup: | fixup: |
| | no | pull = gpio; |
| | | pull-enable = gpio; |
+------+--------------------------------------+--------------------------+
|a1 or | parse regs: |
|later | gpio/mux (without ao domain) |
|SoCs | fixup: |
| | pull = gpio; pull-enable = gpio; ds = gpio; |
+------+-----------------------------------------------------------------+
Since m8-axg share the same ao fixup, make a common function
meson8_aobus_parse_dt_extra to do the job.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/1573819429-6937-2-git-send-email-qianggui.song@amlogic.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some devices do not make use of the CMD0/DAT0/DAT2 direction control
pins of the MMC/SD card 0 interface. In this case we should leave
those pins unconfigured.
A similar case already exists for "mc1_a_1" vs "mc1_a_2"
when the MC1_FBCLK pin is not used.
Add a new "mc0_a_2" pin group which is equal to "mc0_a_1" except
with the MC0_CMDDIR, MC0_DAT0DIR and MC0_DAT2DIR pins removed.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191117205439.239211-1-stephan@gerhold.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
intel-pinctrl for v5.5-1
* Intel Tigerlake pin controller support has been added.
* Miscellaneous fixes to the main and Cherryview drivers.
* Refactoring of the context restoring in the main driver.
The following is an automated git shortlog grouped by driver:
cherryview:
- Missed type change to unsigned int
- Allocate IRQ chip dynamic
- Fix spelling mistake in the comment
- Fix irq_valid_mask calculation
intel:
- Missed type change to unsigned int
- Add Intel Tiger Lake pin controller support
- Use helper to restore register values on ->resume()
- Drop level from warning to debug in intel_restore_hostown()
- Introduce intel_restore_intmask() helper
- Introduce intel_restore_hostown() helper
- Introduce intel_restore_padcfg() helper
- Avoid potential glitches if pin is in GPIO mode
|
|
Linux 5.4-rc5
|
|
We converted 'unsigned' type to be 'unsigned int' in the driver,
but there are couple of leftovers. So, finish the task now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
We converted 'unsigned' type to be 'unsigned int' in the driver,
but there are couple of leftovers. So, finish the task now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Samsung pinctrl drivers changes for v5.5
Fix several device node refcnt leaks (missing of_node_put()) in several
drivers.
|
|
devm_platform_ioremap_resource() internally have platform_get_resource()
and devm_ioremap_resource() in it. So instead of calling them separately
use devm_platform_ioremap_resource() directly.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20191104142654.39256-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If there is a problem with a pinctrl node of a device,
for example, config child node do not have prop specified in
dt_params, num_maps maybe 0. On this condition, no need remember
this map.
Signed-off-by: lijiazi <lijiazi@xiaomi.com>
Link: https://lore.kernel.org/r/29421e7720443a2454830963186f00583c76ce1e.1572588550.git.lijiazi@xiaomi.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
PM8950 and PMI8950 have four MPPs and this driver is compatible.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20191031103507.30678-4-kholk11@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PM8950 features 8 GPIOs with hole in 3 and PMI8950 has
only two; these PMICs are totally compatible with this driver.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20191031103507.30678-2-kholk11@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The get_direction api is strongly recommended to be implemented. In fact
if it is not implemented gpio-hogs will not get the correct direction.
Add an implementation of get_direction for the nsp-gpio driver.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20191104001819.2300-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use more of the gpiolib infrastructure for handling interrupts. The
root interrupt still needs to be handled manually as it is shared with
other peripherals on the SoC.
This will allow multiple instances of this driver to be supported and
will clean up gracefully on failure thanks to the device managed APIs.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20191104001819.2300-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The regs pointer in amd_gpio_irq_handler() should have __iomem
on it, so add that to fix the following sparse warnings:
drivers/pinctrl/pinctrl-amd.c:555:14: warning: incorrect type in assignment (different address spaces)
drivers/pinctrl/pinctrl-amd.c:555:14: expected unsigned int [usertype] *regs
drivers/pinctrl/pinctrl-amd.c:555:14: got void [noderef] <asn:2> *base
drivers/pinctrl/pinctrl-amd.c:563:34: warning: incorrect type in argument 1 (different address spaces)
drivers/pinctrl/pinctrl-amd.c:563:34: expected void const volatile [noderef] <asn:2> *addr
drivers/pinctrl/pinctrl-amd.c:563:34: got unsigned int [usertype] *
drivers/pinctrl/pinctrl-amd.c:580:34: warning: incorrect type in argument 1 (different address spaces)
drivers/pinctrl/pinctrl-amd.c:580:34: expected void const volatile [noderef] <asn:2> *addr
drivers/pinctrl/pinctrl-amd.c:580:34: got unsigned int [usertype] *
drivers/pinctrl/pinctrl-amd.c:587:25: warning: incorrect type in argument 2 (different address spaces)
drivers/pinctrl/pinctrl-amd.c:587:25: expected void volatile [noderef] <asn:2> *addr
drivers/pinctrl/pinctrl-amd.c:587:25: got unsigned int [usertype] *
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20191022151154.5986-1-ben.dooks@codethink.co.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The SDC_QDSD_PINGROUP/UFS_RESET macros are missing the .tile info needed to
calculate the right register offsets. Adding them here and also
adjusting the offsets accordingly.
Fixes: f2ae04c45b1a ("pinctrl: qcom: Add SC7180 pinctrl driver")
Reported-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/20191021141507.24066-1-rnayak@codeaurora.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On SAM9X60, slewrate should be enabled on pins with a switching frequency
below 50Mhz. Since most of our pins do not exceed this value, we enable
slewrate by default. Pins with a switching value that exceeds 50Mhz will
have to explicitly disable slewrate.
This patch changes the ABI. However, the slewrate macros are only used
by SAM9X60 and, at this moment, there are no device-tree files available
for this platform.
Suggested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20191101092031.24896-1-codrin.ciubotariu@microchip.com
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pinctrl: sh-pfc: Updates for v5.5 (take two)
- Add support for the new R-Car M3-W+ (r8a77961) SoC,
- Small fixes and cleanups.
|
|
The definitions for bit field [19:18] of the Peripheral Function Select
Register 3 were accidentally copied from bit field [20], leading to
duplicates for the TCLK1_B function, and missing TCLK0, CAN_CLK_B, and
ET0_ETXD4 functions.
Fix this by adding the missing GPIO_FN_CAN_CLK_B and GPIO_FN_ET0_ETXD4
enum values, and correcting the functions.
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191024131308.16659-1-geert+renesas@glider.be
|
|
Add support for the Pin Function Controller in the R-Car M3-W+
(R8A77961) SoC.
R-Car M3-W+ is pin compatible with R-Car M3-W (R8A77960), which allows
for both SoCs to share a driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023122955.12420-4-geert+renesas@glider.be
|
|
Rename CONFIG_PINCTRL_PFC_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_PINCTRL_PFC_R8A77960, to avoid confusion with R-Car M3-W+
(R8A77961), which will use CONFIG_PINCTRL_PFC_R8A77961.
Extend the dependency of CONFIG_PINCTRL_PFC_R8A77960 from
CONFIG_ARCH_R8A7796 to CONFIG_ARCH_R8A77960, to relax dependencies for a
future rename of the SoC configuration symbol.
Rename r8a7796_pinmux_info to r8a77960_pinmux_info, as it contains an
r8a77960-based name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023122955.12420-3-geert+renesas@glider.be
|
|
As platform_get_irq() now prints an error when the interrupt does not
exist, counting interrupts by looping until failure causes the printing
of scary messages like:
sh-pfc e6060000.pin-controller: IRQ index 0 not found
Fix this by using the platform_irq_count() helper instead.
Fixes: 7723f4c5ecdb8d83 ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191016142601.28255-1-geert+renesas@glider.be
|
|
This driver adds pinctrl/GPIO support for Intel Tiger Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
We can restore only values that had been changed and do not spam kernel log
with unnecessary messages. Convert intel_gpio_update_pad_mode() to a helper
function that will be used across few callers.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we didn't get any new reports from users about wrong settings
of pad ownership, there is no point to spam kernel log with it. Thus,
drop level from warning to debug.
Also, modify format to be in align with the rest restore helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Refactor restoring GPI_IE registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Refactor restoring HOSTSW_OWN registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Deduplicate restoring PADCFGx registers by using a common helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
This patch is heavily based on the attachment to the bug by Christoph Marz.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202543
Fixes: 6e08d6bbebeb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Depends-on: 83b9dc11312f ("pinctrl: cherryview: Associate IRQ descriptors to irqdomain")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
One spelling mistake is being fixed: benerate -> generate.
It is a complimentary fix to the commit 505485a83c55 ("pinctrl:
cherryview fixed typo in comment").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Commit 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux
GPIO translation") has made the cherryview gpio numbers sparse, to get
a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux.
This has greatly simplified things, but the code setting the
irq_valid_mask was not updated for this, so the valid mask is still in
the old "compressed" numbering with the gaps in the pin numbers skipped,
which is wrong as irq_valid_mask needs to be expressed in gpio numbers.
This results in the following error on devices using pin 24 (0x0018) on
the north GPIO controller as an ACPI event source:
[ 0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ
This has been reported (by email) to be happening on a Caterpillar CAT T20
tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1.
This commit uses the pin number instead of the compressed index into
community->pins to clear the correct bits in irq_valid_mask for GPIOs
using GPEs for interrupts, fixing these errors and in case of the
Medion Akoya e2215t also fixing the LID switch not working.
Cc: stable@vger.kernel.org
Fixes: 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.
However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf0162 ("pinctrl: intel: Initialize GPIO properly when used through irqchip")
Cc: stable@vger.kernel.org
Cc: fei.yang@intel.com
Reported-by: Oliver Barta <oliver.barta@aptiv.com>
Reported-by: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
pinctrl: sh-pfc: Updates for v5.5
- Add support for the new RZ/G2N (r8a774b1) SoC,
- Small fixes and cleanups.
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20191016141217.21520-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20191016141053.23740-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For the new Spreadtrum pin controller, it expands 6bits to describe the
pin sleep mode with adding one CM4_SLEEP mode, which means the pin sleep
related configuration will be loaded automatically by hardware when the
CM4 system goes into deep sleep mode.
Signed-off-by: Bruce Chen <bruce.chen@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/8ae52263b0625c416461821c457e6789b67170b6.1571228451.git.baolin.wang@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
AST2600 EMMC support 3 types DAT bus sizes (1, 4 and 8-bit),
corresponding to 3 groups: EMMCG1, EMMCG4 and EMMCG8
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-8-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When UART13G1 is set the pinmux configuration in SCU4B8 for UART13G0
should be cleared.
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-7-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signal descriptors can represent multi-bit bitfields and so have
explicit "enable" and "disable" states. However many descriptor
instances only describe a single bit, and so the SIG_DESC_SET() macro is
provides an abstraction for the single-bit cases: Its expansion
configures the "enable" state to set the bit and "disable" to clear.
SIG_DESC_CLEAR() was introduced to provide a similar single-bit
abstraction for for descriptors to clear the bit of interest. However
its behaviour was defined as the literal inverse of SIG_DESC_SET() - the
impact is the bit of interest is set in the disable path. This behaviour
isn't intuitive and doesn't align with how we want to use the macro in
practice, so make it clear the bit for both the enable and disable
paths.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-6-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The documentation to configure I3C3/FSI1 and I3C4/FSI2 was initially
unclear.
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message, resolve rebase conflicts]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-5-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The I2C function the pin participated in was incorrectly named SDA14
which lead to a failure to mux:
[ 6.884344] No function I2C14 found on pin 7 (7). Found signal(s) MACLINK4, SDA14, GPIOA7 for function(s) MACLINK4, SDA14, GPIOA7
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-4-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some pins crept in that weren't ordered in the list.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-3-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The inner interrupt handler was for the latent IRQ handling,
and that will never be used, inline the unnecessary function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191014111154.9731-3-linus.walleij@linaro.org
|
|
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191014111154.9731-2-linus.walleij@linaro.org
|
|
The latent IRQs are IRQs that have occurred when the system
was down in deep sleep and the GPIO block was powered off.
The PRCMU (power reset and control unit) knows which GPIO
line offset fired an IRQ to wake the system up (if so
desired) and this second IRQ was used to replay the action
when the system came back online after suspend().
This is now known to be the wrong approach to solve this
problem: in a patch series Lina Iyer has suggested to
instead make it possible to model the IRQs as hierarchical
with double parents.
Also the current device trees do not contain the right
information to make this code work, the latent IRQ is not
specified nowadays giving noise like this in the console:
[ 0.612168] gpio 8012e000.gpio: IRQ index 1 not found
[ 0.622523] gpio 8012e080.gpio: IRQ index 1 not found
Let's delete the latent IRQ code and reimplement it properly
when we need it.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191014111154.9731-1-linus.walleij@linaro.org
|
|
This patch do support pinctrl for RK3308 SoCs.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20191015091708.7934-3-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add PIN_CONFIG_BIAS_DISABLE configuration support for Spreadtrum pin
controller.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/66d373ddee61e8be2fcef49aac5e80bd58f14915.1570596606.git.baolin.wang@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
Gregory CLEMENT
Rahul Tanwar
Matti Vaittinen
Qianggui Song
Stephan Gerhold
Linus Walleij
Andy Shevchenko
YueHaibing
lijiazi
AngeloGioacchino Del Regno
Chris Packham
Ben Dooks (Codethink)
Rajendra Nayak
Codrin Ciubotariu
Geert Uytterhoeven
Hans de Goede
Bruce Chen
Johnny Huang
Andrew Jeffery
Jianqun Xu
Baolin Wang