| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
qeth has been supporting multiple HW Output Queues for a long time. But
rather than exposing those queues to the stack, it uses its own queue
selection logic in .ndo_start_xmit... with all the drawbacks that
entails.
Start off by switching IQD devices over to a proper mqs net_device,
and converting all the netdev_queue management code.
One oddity with IQD devices is the requirement to place all mcast
traffic on the _highest_ established HW queue. Doing so via
.ndo_select_queue seems straight-forward - but that won't work if only
some of the HW queues are active
(ie. when dev->real_num_tx_queues < dev->num_tx_queues), since
netdev_cap_txqueue() will not allow us to put skbs on the higher queues.
To make this work, we
1. let .ndo_select_queue() map all mcast traffic to netdev_queue 0, and
2. later re-map the netdev_queue and HW queue indices in
.ndo_start_xmit and the TX completion handler.
With this patch we default to a fixed set of 1 ucast and 1 mcast queue.
Support for dynamic reconfiguration is added at a later time.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The naming of several QDIO helpers doesn't match their actual
functionality, or the structures they operate on. Clean this up.
s/qeth_alloc_qdio_buffers/qeth_alloc_qdio_queues
s/qeth_free_qdio_buffers/qeth_free_qdio_queues
s/qeth_alloc_qdio_out_buf/qeth_alloc_output_queue
s/qeth_clear_outq_buffers/qeth_drain_output_queue
s/qeth_clear_qdio_buffers/qeth_drain_output_queues
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All users of the lock are running in process context now.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The inet6addr_chain is atomic. So instead of starting the cmd IO for
SETIP / DELIP straight from the notifier callback, run it from a
workqueue. This is the last step towards removal of cmd IO completion
polling.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract a little helper, so that high-level callers can manipulate the
IP table without worrying about the locking. This will make it easier
to convert the code to a different locking primitive later on.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The L2 and L3 .ndo_set_rx_mode callbacks maintain an address cache
to decide which addresses have changed since the last modeset.
When the card is set offline, qeth_l?_stop_card() drains this cache.
This happens only after 1) the net_device has been detached, and
2) any pending RX modeset has completed. Consequently we can access the
cache lock-free.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
.ndo_set_rx_mode gets called in process context, but while holding the
addr_list spinlock. Which means we currently can't sleep while
re-programming the HW, and need to poll for IO completion. That's bad,
in particular since receiving the cmd response can fail silently and
we're then polling until the timeout hits.
As a first step towards eliminating the IO completion polling, run the
RX modeset from a work element and only take the addr_list lock while
updating the RX mode address cache.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of the TX completion path, qeth_release_skbs() frees the completed
skbs with __skb_queue_purge(). This ends in kfree_skb(), reporting every
completed skb as dropped.
On the other hand when dropping an skb in .ndo_start_xmit, we end up
calling consume_skb()... where we should be using kfree_skb() so that
drop monitors get notified.
Switch the drop/consume logic around, and also don't accumulate dropped
packets in the tx_errors statistics.
Fixes: dc149e3764d8 ("s390/qeth: replace open-coded skb_queue_walk()")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ucast IP table is utilized by some of the L3-specific sysfs attributes
that qeth_l3_create_device_attributes() provides. So initialize the table
_before_ registering the attributes.
Fixes: ebccc7397e4a ("s390/qeth: add missing hash table initializations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HW trap and VNICC configuration is exposed via sysfs, and may have
already been modified when qeth_l?_probe_device() attempts to initialize
them. So (1) initialize the VNICC values a little earlier, and (2) don't
bother about the HW trap mode, it was already initialized before.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that qeth always uses dev_close() to shutdown the interface, we can
trust the locking and remove some custom state checks.
qeth_l?_stop_card() is no longer called for a card in UP state, so remove
the checks there too. This basically makes the UP state obsolete, so rip
out the whole thing (except for the sysfs-visible string).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It makes no difference whether we
1. manually disarm the HW trap and call the offline code with
recovery_mode == 1, or
2. call the offline code with recovery_mode == 0, and let it disarm the
HW trap for us.
So consolidate the two code paths in the suspend callback.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recovery code already runs in a kthread, we don't have to defer the
offlining further.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smatch complains that __qeth_l3_set_offline() first accesses card->dev,
and then later checks whether the pointer is valid.
Since commit d3d1b205e89f ("s390/qeth: allocate netdevice early"), the
pointer is _always_ valid - that patch merely missed to remove this one
check.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When resetting an interface ("recovery"), qeth currently attempts to
elide the call to dev_close(). We initially only call .ndo_close to
quiesce the data path, and then offline & online the ccwgroup device.
If the reset succeeded, a call to .ndo_open then resumes the data path
along with some internal setup (dev_addr validation, RX modeset) that
dev_open() would have usually triggered.
dev_close() only gets called (via the close_dev worker) if the reset
action fails.
It's unclear whether this was initially done due to locking concerns, or
rather to execute the reset transparently. Either way, temporarily
closing the interface without dev_close() is fragile, and means we're
susceptible to various races and unexpected behaviour. For instance:
- Bypassing dev_deactivate_many() means that the qdiscs are not set to
__QDISC_STATE_DEACTIVATED. Consequently any intermittent TX completion
can wake up the txq, resulting in calls to .ndo_start_xmit while the
data path is down. We have custom state checking to detect this case
and drop such packets.
- Because the IFF_UP flag doesn't reflect the interface's actual state
during a reset, we have custom state checking in .ndo_open and
.ndo_close to guard against invalid calls.
- Considering that the reset might take a considerable amount of time
(in particular if an IO fails and we end up waiting for its timeout), we
_do_ want NETDEV_GOING_DOWN and NETDEV_DOWN events so that components
like bonding, team, bridge, macvlan, vlan, ... can take appropriate
action.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting a L2 qeth device online, enable the HW trap as soon as the
control plane is available. This allows us to catch any error that
occurs during the very first commands.
In the same spirit, the offline code should disable the HW trap as the
very first step of its processing.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The offline code uses a specific RECOVER state to indicate that the
interface should be brought up when a qeth device is set online again.
Rather than having a specific card-state for this, just put it in an
internal flag bit and set the state to DOWN. When working with the
card's state transitions, this reduces the complexity quite a bit.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Accumulate per-TX queue statistics, and increase their size to 64 bit.
Don't bother with enabling/disabling the statistics, the overhead is
negligible.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of this is self-contained code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Counting the number of function calls and the time spent in functions
is best left to proper tracing facilities.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This calls the existing errno translation helpers from the callbacks,
adding trivial wrappers where necessary. For cmds that have no
sophisticated errno translation, default to -EIO.
For IPA cmds with no callback, fall back to a minimal default. This is
currently being used by qeth_l3_send_setrouting().
Thus having all converted all callbacks, remove the legacy path in
qeth_send_control_data_cb().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Error propagation from cmd callbacks currently works in a way where
qeth_send_control_data_cb() picks the raw HW code from the response,
and the cmd's originator later translates this into an errno.
The callback itself only returns 0 ("done") or 1 ("expect more data").
This is
1. limiting, as the only means for the callback to report an internal
error is to invent pseudo HW codes (such as IPA_RC_ENOMEM), that
the originator then needs to understand. For non-IPA callbacks, we
even provide a separate field in the IO buffer metadata (iob->rc) so
the callback can pass back a return value.
2. fragile, as the originator must take care to not translate any errno
that is returned by qeth's own IO code paths (eg -ENOMEM). Also, any
originator that forgets to translate the HW codes potentially passes
garbage back to its caller. For instance, see
commit 2aa4867198c2 ("s390/qeth: translate SETVLAN/DELVLAN errors").
Introduce a new model where all HW error translation is done within the
callback, and the callback returns
> 0, if it expects more data (as before)
== 0, on success
< 0, with an errno
Start off with converting all callbacks to the new model that either
a) pass back pseudo HW codes, or b) have a dependency on a specific
HW error code. Also convert c) the one callback that uses iob->rc, and
d) qeth_setadpparms_change_macaddr_cb() so that it can pass back an
error back to qeth_l2_request_initial_mac() even when the cmd itself
was successful.
The old model remains supported: if the callback returns 0, we still
propagate the response's HW error code back to the originator.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_l3_query_arp_cache_info() indicates a data length that's much
larger than the actual length of its request (ie. the value passed to
qeth_get_setassparms_cmd()). The confusion presumably comes from the
fact that the cmd _response_ can be quite large - but that's no concern
for the initial request IO.
Fixing this up allows us to use the generic qeth_send_ipa_cmd()
infrastructure.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Work for Bridgeport events is currently placed on a driver-wide
workqueue. If the card is removed and freed while any such work is still
active, this causes a use-after-free.
So put the events on a per-card queue, where we can control their
lifetime. As we also don't want stale events to last beyond an
offline & online cycle, flush this queue when setting the card offline.
Fixes: b4d72c08b358 ("qeth: bridgeport support - basic control")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A card's close_dev work is scheduled on a driver-wide workqueue. If the
card is removed and freed while the work is still active, this causes a
use-after-free.
So make sure that the work is completed before freeing the card.
Fixes: 0f54761d167f ("qeth: Support VEPA mode")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a qeth card is offline, it has no connection to the HW. So none of
our control callbacks can run IO against it, and we can only cache the
input (eg a new MAC address) without providing proper feedback to the
caller. In this context, it seems much more reasonable to simply detach
the netdevice and let the kernel reject any interaction with it.
This also makes all sorts of internal state checks and locking obsolete.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-order the code flow a bit so that all initial HW setup is done before
putting the netdevice into play. For a netdevice that hasn't been
registered before, we also don't need to re-enable its HW features or
check for recovery actions.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At best this is redundant, at worst it papers over a race in the
offline / online code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The L2 and L3 code for these ops is almost identical, we only need to
provide a custom ndo_validate_addr() for L2 that checks whether
programming the MAC address succeeded.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to pass extack together with NETDEV_PRE_UP notifications, it's
necessary to route the extack to __dev_open() from diverse (possibly
indirect) callers. One prominent API through which the notification is
invoked is dev_open().
Therefore extend dev_open() with and extra extack argument and update
all users. Most of the calls end up just encoding NULL, but bond and
team drivers have the extack readily available.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_l3_setup_netdev() checks if the hsuid attribute is set on the qeth
device, and propagates it to the net_device. In the past this was needed
to pick up any hsuid that was set before allocation of the net_device.
With commit d3d1b205e89f ("s390/qeth: allocate netdevice early") this
is no longer necessary, qeth_l3_dev_hsuid_store() always stores the
hsuid straight into dev->perm_addr.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the CREATE ADDR sent by qeth_l3_iqd_read_initial_mac() fails, its
callback sets a random MAC address on the net_device. The error then
propagates back, and qeth_l3_setup_netdev() bails out without
registering the net_device.
Any subsequent call to qeth_l3_setup_netdev() will then attempt a fresh
CREATE ADDR which either 1) also fails, or 2) sets a proper MAC address
on the net_device. Consequently, the net_device will never be registered
with a random MAC and we can drop the fallback code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_l3_send_ipa_arp_cmd() is merely a wrapper around
qeth_send_control_data() now. So push the length adjustment into
QETH_SETASS_BASE_LEN, and remove the wrapper. While at it, also remove
some redundant 0-initializations.
qeth_send_setassparms() requires that callers prepare their command
parameters, so that they can be copied into the parameter area in one
go. Skip the indirection, and just let callers set up the command
themselves.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call qeth_prepare_ipa_cmd() during setup of a new IPA cmd buffer, so
that it is used for all commands. Thus ARP and SNMP requests don't have
to do their own initialization.
This will now also set the proper MPC protocol version for SNMP requests
on L2 devices.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 82bf5c0867f6 ("s390/qeth: add support for IPv6 TSO"),
qeth_xmit() also knows how to build TSO packets and is practically
identical to qeth_l3_xmit().
Convert qeth_l3_xmit() into a thin wrapper that merely strips the
L2 header off a packet, and calls qeth_xmit() for the actual
TX processing.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Filling the HW header from one single function will make it easier to
rip out all the duplicated transmit code in qeth_l3_xmit(). On top, this
saves one conditional branch in the TSO path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ARP_{ADD,REMOVE}_ENTRY cmd structs contain reserved fields.
Introduce a common helper that doesn't raw-copy the user-provided data
into the cmd, but only sets those fields that are strictly needed for
the command.
This also sets the correct command length for ARP_REMOVE_ENTRY.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting the carrier 'on' for an unregistered netdevice doesn't update
its operstate. Fix this by delaying the update until the netdevice has
been registered.
Fixes: 91cc98f51e3d ("s390/qeth: remove duplicated carrier state tracking")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth only registers its netdevice when the qeth device is first set
online. Thus a device that has never been set online will trigger
a WARN ("network todo 'hsi%d' but state 0") in unregister_netdev() when
removed.
Fix this by protecting the unregister step, just like we already protect
against repeated registering of the netdevice.
Fixes: d3d1b205e89f ("s390/qeth: allocate netdevice early")
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sniffing mode for L3 HiperSockets requires that no IP addresses are
registered with the HW. The preferred way to achieve this is for
userspace to delete all the IPs on the interface. But qeth is expected
to also tolerate a configuration where that is not the case, by skipping
the IP registration when in sniffer mode.
Since commit 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
reworked the IP registration logic in the L3 subdriver, this no longer
works. When the qeth device is set online, qeth_l3_recover_ip() now
unconditionally registers all unicast addresses from our internal
IP table.
While we could fix this particular problem by skipping
qeth_l3_recover_ip() on a sniffer device, the more future-proof change
is to skip the IP address registration at the lowest level. This way we
a) catch any future code path that attempts to register an IP address
without considering the sniffer scenario, and
b) continue to build up our internal IP table, so that if sniffer mode
is switched off later we can operate just like normal.
Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Documentation/s390/s390dbf.txt states quite clearly, using any
pointer in sprinf-formatted s390dbf debug entries is dangerous.
The pointers are dereferenced whenever the trace file is read from.
So if the referenced data has a shorter life-time than the trace file,
any read operation can result in a use-after-free.
So rip out all hazardous use of indirect data, and replace any usage of
dev_name() and such by the Bus ID number.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Except for the new HW header id, this works just like TSO6 on L3 devices
and reuses all the existing data path support in qeth_xmit().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds TSO6 support for L3 qeth devices.
Just like for standard IPv6 traffic, TSO6 doesn't use IP offload and
thus runs over the normal qeth_xmit() path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netdevice is always available, apply any carrier state changes to it
without caching them.
On a STARTLAN event (ie. carrier-up), defer updating the state to
qeth_core_hardsetup_card() in the subsequent recovery action.
Also remove the carrier-state checks from the xmit routines. Stopping
transmission on carrier-down is the responsibility of upper-level code
(eg see dev_direct_xmit()).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. tracing iob->rc makes no sense when it hasn't been modified by the
callback,
2. the qeth_dbf_list is declared with LIST_HEAD, which also initializes
the list,
3. the ccwgroup core only calls the thaw/restore callbacks if the gdev
is online, so we don't have to check for it again.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch attempts to untangle the TX and RX code in qeth from
af_iucv's respective HiperTransport path:
On the TX side, pointing skb_network_header() at the IUCV header
means that qeth_l3_fill_af_iucv_hdr() no longer needs a magical offset
to access the header.
On the RX side, qeth pulls the (fake) L2 header off the skb like any
normal ethernet driver would. This makes working with the IUCV header
in af_iucv easier, since we no longer have to assume a fixed skb layout.
While at it, replace the open-coded length checks in af_iucv's RX path
with pskb_may_pull().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Device initialization code usually first loads a subdriver
(via qeth_core_load_discipline()), and then runs its setup() callback.
If this fails, it rolls back the load via qeth_core_free_discipline().
qeth_core_free_discipline() expects the options.layer attribute to be
initialized, but on error in setup() that's currently not the case.
Resulting in misbalanced symbol_put() calls.
Fix this by setting options.layer when loading the subdriver.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While the raw values are fixed due to their use in a sysfs attribute,
we can still use the proper QETH_DISCIPLINE_* enum within the driver.
Also move the initialization into qeth_set_initial_options(), along with
all other user-configurable fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling napi_schedule() from process context does not ensure that the
NET_RX softirq is run in a timely fashion. So trigger it manually.
This is no big issue with current code. A call to ndo_open() is usually
followed by a ndo_set_rx_mode() call, and for qeth this contains a
spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out
early.
Nevertheless it's best to not depend on this behaviour, and just fix
the issue at its source like all other drivers do. For instance see
commit 83a0c6e58901 ("i40e: Invoke softirqs after napi_reschedule").
Fixes: a1c3ed4c9ca0 ("qeth: NAPI support for l2 and l3 discipline")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Julian Wiedmann
David S. Miller
Petr Machata