Age | Commit message (Collapse) | Author | Files | Lines |
|
This increment of rmi_smbus in rmi_smb_read/write_block() causes
garbage to be read/written.
The first read of SMB_MAX_COUNT bytes is fine, but after that
it is nonsense. Trial-and-error showed that by dropping the
increment of rmiaddr everything is fine and the F54 function
properly works.
I tried a hack with rmi_smb_write_block() as well (writing to the
same F54 touchpad data area, then reading it back), and that
suggests that there too the rmiaddr increment has to be dropped.
It makes sense that if it has to be dropped for read, then it has
to be dropped for write as well.
It looks like the initial work with F54 was done using i2c, not smbus,
and it seems nobody ever tested F54 with smbus. The other functions
all read/write less than SMB_MAX_COUNT as far as I can tell, so this
issue was never noticed with non-F54 functions.
With this change I can read out the touchpad data correctly on my
Lenovo X1 Carbon 6th Gen laptop.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/8dd22e21-4933-8e9c-a696-d281872c8de7@xs4all.nl
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
F34 is a bit special as it reinitializes the device and related driver
structs during the firmware update. This clears the fn_irq_mask which
will then prevent F34 from receiving further interrupts, leading to
timeouts during the firmware update. Make sure to reinitialize the
IRQ enables at the appropriate times.
The issue is in F34 code, but the commit in the fixes tag exposed the
issue, as before this commit things would work by accident.
Fixes: 363c53875aef (Input: synaptics-rmi4 - avoid processing unknown IRQs)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191129133514.23224-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The touchscreen on the Teclast X89 is mounted upside down in relation to
the display orientation (the touchscreen itself is mounted upright, but the
display is mounted upside-down). Add a quirk for this so that we send
coordinates which match the display orientation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20191202085636.6650-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Always return EPOLLOUT from uinput_poll to allow polling /dev/uinput
for writable state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Link: https://lore.kernel.org/r/20191204025014.5189-1-marcel@holtmann.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Gratuitous NULL initializers rarely help and often prevent compiler
from warning about using uninitialized variable. Let's remove them.
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/20191125211407.GA97812@dtor-ws
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
mgag200- Fix hw with broken 'startadd' support (Thomas)
mst- Avoid skipping payloads in payload deletion loop (Wayne)
omap- Fix dma_addr refcounting (Tomi)
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204212255.GA256395@art_vandelay
|
|
drm/tegra: Fixes for v5.5-rc1
This is a set of small fixes, mostly for regressions introduced with the
DMA API and DisplayPort support in the main pull request for v5.5-rc1.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204124316.3534855-1-thierry.reding@gmail.com
|
|
[Why]
If the payload_state is DP_PAYLOAD_DELETE_LOCAL in series, current
code doesn't delete the payload at current index and just move the
index to next one after shuffling payloads.
[How]
Drop the i++ increasing part in for loop head and decide whether
to increase the index or not according to payload_state of current
payload.
Changes since v1:
* Refine the code to have it easy reading
* Amend the commit message to meet the way code is modified now.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Fixes: 706246c761dd ("drm/dp_mst: Refactor drm_dp_update_payload_part1()")
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Juston Li <juston.li@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.1+
[Added cc for stable]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203042423.5961-1-Wayne.Lin@amd.com
|
|
Pull additional ACPI updates from Rafael Wysocki:
"These close a nasty race condition in the ACPI memory mappings
management code and an invalid parameter check in a library routing,
allow GPE 0xFF to be masked via kernel command line, add a new lid
switch blacklist entry and clean up Kconfig.
Specifics:
- Fix locking issue in acpi_os_map_cleanup() leading to a race
condition that can be harnessed for provoking a kernel panic from
user space (Francesco Ruggeri)
- Fix parameter check in acpi_bus_get_private_data() (Vamshi K
Sthambamkadi)
- Allow GPE 0xFF to be masked via kernel command line (Yunfeng Ye)
- Add a new lid switch blacklist entry for Acer Switch 10 SW5-032 to
the ACPI button driver (Hans de Goede)
- Clean up Kconfig (Krzysztof Kozlowski)"
* tag 'acpi-5.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: bus: Fix NULL pointer check in acpi_bus_get_private_data()
ACPI: Fix Kconfig indentation
ACPI: OSL: only free map once in osl.c
ACPI: button: Add DMI quirk for Acer Switch 10 SW5-032 lid-switch
ACPI: sysfs: Change ACPI_MASKABLE_GPE_MAX to 0x100
|
|
Pull additional power management updates from Rafael Wysocki:
"These fix an ACPI EC driver bug exposed by the recent rework of the
suspend-to-idle code flow, reintroduce frequency constraints into
device PM QoS (in preparation for adding QoS support to devfreq), drop
a redundant field from struct cpuidle_state and clean up Kconfig in
some places.
Specifics:
- Avoid a race condition in the ACPI EC driver that may cause systems
to be unable to leave suspend-to-idle (Rafael Wysocki)
- Drop the "disabled" field, which is redundant, from struct
cpuidle_state (Rafael Wysocki)
- Reintroduce device PM QoS frequency constraints (temporarily
introduced and than dropped during the 5.4 cycle) in preparation
for adding QoS support to devfreq (Leonard Crestez)
- Clean up indentation (in multiple places) and the cpuidle drivers
help text in Kconfig (Krzysztof Kozlowski, Randy Dunlap)"
* tag 'pm-5.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Rework ACPI events synchronization
ACPI: EC: Rework flushing of pending work
PM / devfreq: Add missing locking while setting suspend_freq
PM / QoS: Restore DEV_PM_QOS_MIN/MAX_FREQUENCY
PM / QoS: Reorder pm_qos/freq_qos/dev_pm_qos structs
PM / QoS: Initial kunit test
PM / QoS: Redefine FREQ_QOS_MAX_DEFAULT_VALUE to S32_MAX
power: avs: Fix Kconfig indentation
cpufreq: Fix Kconfig indentation
cpuidle: minor Kconfig help text fixes
cpuidle: Drop disabled field from struct cpuidle_state
cpuidle: Fix Kconfig indentation
|
|
|
|
cec4fa7511ef7a73eb635834e9d85b25a5b47a98 ("drm/omap: use refcount API to
track the number of users of dma_addr") changed omap_gem.c to use
refcounting API to track dma_addr uses. However, the driver only tracks
the refcounts for non-contiguous buffers, and the patch didn't fully
take this in account.
After the patch, the driver always decreased refcount in omap_gem_unpin,
instead of decreasing the refcount only for non-contiguous buffers. This
leads to refcounting mismatch.
As for the contiguous cases the refcount is never increased, fix this
issue by returning from omap_gem_unpin if the buffer being unpinned is
contiguous.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191114080343.30704-1-tomi.valkeinen@ti.com
Fixes: cec4fa7511ef ("drm/omap: use refcount API to track the number of users of dma_addr")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
If BLK_DEV_ZONED isn't set, 'ret' isn't used. This makes gcc complain,
rightfully. Move ret where it is used.
Fixes: 979d54475e0b ("null_blk: cleanup null_gendisk_register")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Queue dma alignment limit requires users(fs, target, ...) of block layer
to pass aligned buffer.
So far brd doesn't support un-aligned buffer, even though it is easy
to support it.
However, given brd is often used for debug purpose, and there are other
drivers which can't support un-aligned buffer too.
So add warning so that brd users know what to fix.
Reported-by: Stephen Rust <srust@blockbridge.com>
Cc: Stephen Rust <srust@blockbridge.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Now we depend on blk_queue_split() to respect most of queue limit
(the only one exception could be dma alignment), however
blk_queue_split() isn't used for brd, so this limit isn't respected
since v4.3.
Also max_hw_sectors limit doesn't play a big role for brd, which is
added since brd is added to tree for unknown reason.
So remove it.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The call to tegra_display_hub_cleanup() that takes care of disabling the
window groups is missing from the driver's ->remove() callback. Call it
to make sure the runtime PM reference counts for the display controllers
are balanced.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The SOR supports multiple display modes, but only when driving an HDMI
monitor does it make sense to control the +5V power supply. eDP and DP
don't need this, so make it optional.
This fixes a crash observed during system suspend/resume.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Subdevices may not be hooked up to an IOMMU via device tree. Detect such
situations and avoid confusing users by not emitting an error message.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Export the module device table to ensure the VIC compatible strings are
listed in the module's aliases table. This in turn causes the driver to
be automatically loaded on boot if VIC is the only enabled subdevice of
the logical host1x DRM device.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Upon system suspend, make sure the +5V HDMI regulator is disabled. This
avoids potentially leaking current to the HDMI connector. This also
makes sure that upon resume the regulator is enabled again, which in
some cases is necessary to properly restore the state of the supply on
resume.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The IOVA address for the cursor is the result of mapping the buffer
object for the given display controller. Make sure to use the proper
IOVA address as stored in the cursor's plane state.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
All the display related blocks on Tegra require contiguous memory. Using
the DMA API, there is no knowing at import time which device will end up
using the buffer, so it's not known whether or not an IOMMU will be used
to map the buffer.
Move the check for non-contiguous buffers/mappings to the tegra_dc_pin()
function which is now the earliest point where it is known if a DMA BUF
can be used by the given device or not.
v2: add check for contiguous buffer/mapping in tegra_dc_pin()
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Buffers that are imported from a DMA-BUF don't have pages allocated with
them. At the same time an SG table for them can't be derived using the
DMA API helpers because the necessary information doesn't exist. However
there's already an SG table that was created during import, so this can
simply be duplicated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra DRM never actually took that lock, so the driver was broken
until generic locking was added in commit:
commit b962a12050a387e4bbf3a48745afe1d29d396b0d
Author: Rob Clark <robdclark@gmail.com>
Date: Mon Oct 22 14:31:22 2018 +0200
drm/atomic: integrate modeset lock with private objects
It's now no longer necessary to take that lock, so drop the check.
v2: add rationale for why it is now safe to drop the check (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a module_exit() to perform the necessary clean-up.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: "Roger Pau Monné" <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
To prevent a PV driver module being removed whilst attached to its other
end, and hence xenbus calling into potentially invalid text, take a
reference on the module before calling the probe() method (dropping it if
unsuccessful) and drop the reference after returning from the remove()
method.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
* acpi-bus:
ACPI: bus: Fix NULL pointer check in acpi_bus_get_private_data()
* acpi-button:
ACPI: button: Add DMI quirk for Acer Switch 10 SW5-032 lid-switch
* acpi-sysfs:
ACPI: sysfs: Change ACPI_MASKABLE_GPE_MAX to 0x100
* acpi-misc:
ACPI: Fix Kconfig indentation
|
|
* pm-sleep:
ACPI: PM: s2idle: Rework ACPI events synchronization
ACPI: EC: Rework flushing of pending work
* pm-cpuidle:
cpuidle: minor Kconfig help text fixes
cpuidle: Drop disabled field from struct cpuidle_state
cpuidle: Fix Kconfig indentation
* pm-cpufreq:
cpufreq: Fix Kconfig indentation
* pm-devfreq:
PM / devfreq: Add missing locking while setting suspend_freq
* pm-avs:
power: avs: Fix Kconfig indentation
|
|
This patch add documentation about the bridge parameter in several
function.
This will fix the following build warning:
drivers/char/agp/generic.c:220: warning: No description found for parameter 'bridge'
drivers/char/agp/generic.c:364: warning: No description found for parameter 'bridge'
drivers/char/agp/generic.c:1283: warning: No description found for parameter 'bridge'
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1574324085-4338-5-git-send-email-clabbe@baylibre.com
|
|
This patch fix the following build warning:
warning: variable 'num_segments' set but not used [-Wunused-but-set-variable]
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1574324085-4338-4-git-send-email-clabbe@baylibre.com
|
|
This patch fix the following warning:
drivers/char/agp/generic.c:853:6: attention : variable ‘size’ set but not used [-Wunused-but-set-variable]
by removing the unused variable size in agp_generic_create_gatt_table
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1574324085-4338-2-git-send-email-clabbe@baylibre.com
|
|
drm-next-5.5-2019-12-03:
amdgpu:
- Fix vram lost handling with BACO on VI/CI asics
- DC fixes for Navi14
- Misc gfx10 fixes
- SR-IOV fixes
- Fix driver unload
- Fix XGMI limits on Arcturus
amdkfd:
- Enable KFD on PPC
- Optimize KFD page table reservations
radeon:
- Fix register checker for r1xx/r2xx
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203204135.5437-1-alexander.deucher@amd.com
|
|
Pull chrome platform changes from Benson Leung:
"CrOS EC / MFD / IIO:
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part
of a series from Gwendal to refactor sensor code between MFD, CrOS
EC, iio and input in order to add a new sensorhub driver and FIFO
processing
Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue)"
* tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: fix use after free issue
platform/chrome: cros_ec: Add Kconfig default for cros-ec-sensorhub
Revert "Input: cros_ec_keyb: mask out extra flags in event_type"
Revert "Input: cros_ec_keyb - add back missing mask for event_type"
platform/chrome: cros_ec: handle MKBP more events flag
platform/chrome: cros_ec: Do not attempt to register a non-positive IRQ number
platform/chrome: cros-ec: Record event timestamp in the hard irq
mfd / platform / iio: cros_ec: Register sensor through sensorhub
iio / platform: cros_ec: Add cros-ec-sensorhub driver
mfd / platform: cros_ec: Add sensor_count and make check_features public
platform/chrome: cros_ec: Put docs with the code
platform/chrome: cros_usbpd_logger: add missed destroy_workqueue in remove
platform/chrome: cros_ec: Fix Kconfig indentation
platform/chrome: wilco_ec: Add keyboard backlight LED support
platform/chrome: wilco_ec: Add charging config driver
platform/chrome: wilco_ec: Add Dell's USB PowerShare Policy control
platform/chrome: wilco_ec: Add debugfs test_event file
|
|
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
|
|
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
|
|
Pull RTC updates from Alexandre Belloni:
"A lot of unnecessary code removal in here that ends up decreasing the
number of lines in the subsystem. The ds1343 and ds1347 drivers got
cleaned up. The rest are the usual fixes and new features.
Subsystem:
- fix warnings and errors with make W=1
- UIE are now disabled while setting the RTC time
- UIE are now disallowed when the RTC time is not set.
Drivers:
- remove unecessary .remove callbacks
- Set RTC range for cros-ec, ds1343, ds1347, m41t80, s35390a, vt8500
- Use devm_platform_ioremap_resource where applicable
- rv3028: add clock out support"
* tag 'rtc-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (81 commits)
rtc: Fix Kconfig indentation
rtc: xgene: Remove unused struct device in struct xgene_rtc_dev
rtc: sun6i: Remove struct device from sun6i_rtc_dev
rtc: st-lpc: Remove struct resource from struct st_rtc
rtc: pcf8523: Remove struct pcf8523
rtc: meson: remove redundant assignment to variable retries
rtc: v3020: remove set but unused variable
rtc: tegra: remove set but unused variable
rtc: pm8xxx: update kerneldoc for struct pm8xxx_rtc
rtc: m41t80: remove excess kerneldoc
rtc: ds1685: fix build error with make W=1
rtc: ds1685: remove set but unused variables
rtc: ds1374: remove unused variable
rtc: sysfs: fix hctosys_show kerneldoc
rtc: interface: fix kerneldoc comments
rtc: msm6242: Remove unneeded msm6242_set()/msm6242_clear() functions
rtc: msm6242: Fix reading of 10-hour digit
rtc: tps65910: allow using RTC without alarm interrupt
rtc: fsl-ftm-alarm: remove select FSL_RCPM and default y from Kconfig
rtc: pcf8563: Constify clkout_rates
...
|
|
On systems with STACKTRACE_SUPPORT=n, we get:
WARNING: unmet direct dependencies detected for STACKTRACE
Depends on [n]: STACKTRACE_SUPPORT
Selected by [y]:
- STACKDEPOT [=y]
and build errors such as:
m68k-linux-ld: kernel/stacktrace.o: in function `stack_trace_save':
(.text+0x11c): undefined reference to `save_stack_trace'
Add the missing deendency on STACKTRACE_SUPPORT.
Fixes: 12a280c72868 ("drm/dp_mst: Add topology ref history tracking for debugging")
Cc: Lyude Paul <lyude@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191202133650.11964-1-linux@roeck-us.net
|
|
For each I/O request, blkback first maps the foreign pages for the
request to its local pages. If an allocation of a local page for the
mapping fails, it should unmap every mapping already made for the
request.
However, blkback's handling mechanism for the allocation failure does
not mark the remaining foreign pages as unmapped. Therefore, the unmap
function merely tries to unmap every valid grant page for the request,
including the pages not mapped due to the allocation failure. On a
system that fails the allocation frequently, this problem leads to
following kernel crash.
[ 372.012538] BUG: unable to handle kernel NULL pointer dereference at 0000000000000001
[ 372.012546] IP: [<ffffffff814071ac>] gnttab_unmap_refs.part.7+0x1c/0x40
[ 372.012557] PGD 16f3e9067 PUD 16426e067 PMD 0
[ 372.012562] Oops: 0002 [#1] SMP
[ 372.012566] Modules linked in: act_police sch_ingress cls_u32
...
[ 372.012746] Call Trace:
[ 372.012752] [<ffffffff81407204>] gnttab_unmap_refs+0x34/0x40
[ 372.012759] [<ffffffffa0335ae3>] xen_blkbk_unmap+0x83/0x150 [xen_blkback]
...
[ 372.012802] [<ffffffffa0336c50>] dispatch_rw_block_io+0x970/0x980 [xen_blkback]
...
Decompressing Linux... Parsing ELF... done.
Booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
This commit fixes this problem by marking the grant pages of the given
request that didn't mapped due to the allocation failure as invalid.
Fixes: c6cc142dac52 ("xen-blkback: use balloon pages for all mappings")
Reviewed-by: David Woodhouse <dwmw@amazon.de>
Reviewed-by: Maximilian Heyne <mheyne@amazon.de>
Reviewed-by: Paul Durrant <pdurrant@amazon.co.uk>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull more s390 updates from Vasily Gorbik:
- Make stack unwinder reliable and suitable for livepatching. Add
unwinder testing module.
- Fixes for CALL_ON_STACK helper used for stack switching.
- Fix unwinding from bpf code.
- Fix getcpu and remove compat support in vdso code.
- Fix address space control registers initialization.
- Save KASLR offset for early dumps.
- Handle new FILTERED_BY_HYPERVISOR reply code in crypto code.
- Minor perf code cleanup and potential memory leak fix.
- Add couple of error messages for corner cases during PCI device
creation.
* tag 's390-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (33 commits)
s390: remove compat vdso code
s390/livepatch: Implement reliable stack tracing for the consistency model
s390/unwind: add stack pointer alignment sanity checks
s390/unwind: filter out unreliable bogus %r14
s390/unwind: start unwinding from reliable state
s390/test_unwind: add program check context tests
s390/test_unwind: add irq context tests
s390/test_unwind: print verbose unwinding results
s390/test_unwind: add CALL_ON_STACK tests
s390: fix register clobbering in CALL_ON_STACK
s390/test_unwind: require that unwinding ended successfully
s390/unwind: add a test for the internal API
s390/unwind: always inline get_stack_pointer
s390/pci: add error message on device number limit
s390/pci: add error message for UID collision
s390/cpum_sf: Check for SDBT and SDB consistency
s390/cpum_sf: Use TEAR_REG macro consistantly
s390/cpum_sf: Remove unnecessary check for pending SDBs
s390/cpum_sf: Replace function name in debug statements
s390/kaslr: store KASLR offset for early dumps
...
|
|
Pull timer updates from Ingo Molnar:
"The main changes in the timer code in this cycle were:
- Clockevent updates:
- timer-of framework cleanups. (Geert Uytterhoeven)
- Use timer-of for the renesas-ostm and the device name to prevent
name collision in case of multiple timers. (Geert Uytterhoeven)
- Check if there is an error after calling of_clk_get in asm9260
(Chuhong Yuan)
- ABI fix: Zero out high order bits of nanoseconds on compat
syscalls. This got broken a year ago, with apparently no side
effects so far.
Since the kernel would use random data otherwise I don't think we'd
have other options but to fix the bug, even if there was a side
effect to applications (Dmitry Safonov)
- Optimize ns_to_timespec64() on 32-bit systems: move away from
div_s64_rem() which can be slow, to div_u64_rem() which is faster
(Arnd Bergmann)
- Annotate KCSAN-reported false positive data races in
hrtimer_is_queued() users by moving timer->state handling over to
the READ_ONCE()/WRITE_ONCE() APIs. This documents these accesses
(Eric Dumazet)
- Misc cleanups and small fixes"
[ I undid the "ABI fix" and updated the comments instead. The reason
there were apparently no side effects is that the fix was a no-op.
The updated comment is to say _why_ it was a no-op. - Linus ]
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Zero the upper 32-bits in __kernel_timespec on 32-bit
time: Rename tsk->real_start_time to ->start_boottime
hrtimer: Remove the comment about not used HRTIMER_SOFTIRQ
time: Fix spelling mistake in comment
time: Optimize ns_to_timespec64()
hrtimer: Annotate lockless access to timer->state
clocksource/drivers/asm9260: Add a check for of_clk_get
clocksource/drivers/renesas-ostm: Use unique device name instead of ostm
clocksource/drivers/renesas-ostm: Convert to timer_of
clocksource/drivers/timer-of: Use unique device name instead of timer
clocksource/drivers/timer-of: Convert last full_name to %pOF
|
|
Shift and mask were reversed. Noticed by chance.
Tested-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Pull irq updates from Ingo Molnar:
"Most of the IRQ subsystem changes in this cycle were irq-chip driver
updates:
- Qualcomm PDC wakeup interrupt support
- Layerscape external IRQ support
- Broadcom bcm7038 PM and wakeup support
- Ingenic driver cleanup and modernization
- GICv3 ITS preparation for GICv4.1 updates
- GICv4 fixes
There's also the series from Frederic Weisbecker that fixes memory
ordering bugs for the irq-work logic, whose primary fix is to turn
work->irq_work.flags into an atomic variable and then convert the
complex (and buggy) atomic_cmpxchg() loop in irq_work_claim() into a
much simpler atomic_fetch_or() call.
There are also various smaller cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
pinctrl/sdm845: Add PDC wakeup interrupt map for GPIOs
pinctrl/msm: Setup GPIO chip in hierarchy
irqchip/qcom-pdc: Add irqchip set/get state calls
irqchip/qcom-pdc: Add irqdomain for wakeup capable GPIOs
irqchip/qcom-pdc: Do not toggle IRQ_ENABLE during mask/unmask
irqchip/qcom-pdc: Update max PDC interrupts
of/irq: Document properties for wakeup interrupt parent
genirq: Introduce irq_chip_get/set_parent_state calls
irqdomain: Add bus token DOMAIN_BUS_WAKEUP
genirq: Fix function documentation of __irq_alloc_descs()
irq_work: Fix IRQ_WORK_BUSY bit clearing
irqchip/ti-sci-inta: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
irq_work: Slightly simplify IRQ_WORK_PENDING clearing
irq_work: Fix irq_work_claim() memory ordering
irq_work: Convert flags to atomic_t
irqchip: Ingenic: Add process for more than one irq at the same time.
irqchip: ingenic: Alloc generic chips from IRQ domain
irqchip: ingenic: Get virq number from IRQ domain
irqchip: ingenic: Error out if IRQ domain creation failed
irqchip: ingenic: Drop redundant irq_suspend / irq_resume functions
...
|
|
Pull dmi updates from Jean Delvare.
* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
firmware: dmi: Add dmi_memdev_handle
firmware: dmi: Remember the memory type
|
|
The current zone revalidation code has a major problem in that it
doesn't update the zone size and q->nr_zones atomically, leading
to a short window where an out of bounds access to the zone arrays
is possible.
To fix this move the setting of the zone size into the crticial
sections blk_revalidate_disk_zones so that it gets updated together
with the zone bitmaps and q->nr_zones. This also slightly simplifies
the caller as it deducts the zone size from the report_zones.
This change also allows to check for a power of two zone size in generic
code.
Reported-by: Hans Holmberg <hans@owltronix.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
still need to init csb even for SRIOV
v2:
drop init_pg() for gfx10 at all since
PG and GFX off feature will be fully controled
by RLC and SMU fw for gfx10
v3:
drop the flush_gpu_tlb lines since we consider
it is only usefull in emulation
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
To align with the scheme from gfx9
disabling GFX ring after VM shutdown could avoid
garbage data be fetched to GFX RB which may lead
to unnecessary screw up on GFX
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
since we don't have RLCG ucode loading and no SRlist as well
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
issue:
kernel would report a warning from a double unpin
during the driver unloading on the CSB bo
why:
we unpin it during hw_fini, and there will be another
unpin in sw_fini on CSB bo.
fix:
actually we don't need to pin/unpin it during
hw_init/fini since it is created with kernel pinned,
we only need to fullfill the CSB again during hw_init
to prevent CSB/VRAM lost after S3
v2:
get_csb in init_rlc so hw_init() will make CSIB content
back even after reset or s3
v3:
use bo_create_kernel instead of bo_create_reserved for CSB
otherwise the bo_free_kernel() on CSB is not aligned and
would lead to its internal reserve pending there forever
take care of gfx7/8 as well
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
srbm_mutex is to guarantee atomicity for r/w of gfx indexed registers
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|