Age | Commit message (Collapse) | Author | Files | Lines |
|
Add the upcoming ConnectX-6 LX device ID.
Fixes: 85327a9c4150 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Shani Shapp <shanish@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Once all the large flow groups (defined by the user when the flow table
is created - max_num_groups) were created, then all the following new
flow groups will have only one flow table entry, even though the flow table
has place to larger groups.
Fix the condition to prefer large flow group.
Fixes: f0d22d187473 ("net/mlx5_core: Introduce flow steering autogrouped flow table")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Device that doesn't support IP-in-IP offloads has to filter csum and gso
offload support, otherwise kernel will conclude that device is capable of
offloading csum and gso for IP-in-IP tunnels and that might result in
IP-in-IP tunnel not functioning.
Fixes: 25948b87dda2 ("net/mlx5e: Support TSO and TX checksum offloads for IP-in-IP")
Signed-off-by: Marina Varshaver <marinav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
On some old Firmwares, connector type value was not supported, and value
read from FW was 0. For those, driver used link mode in order to set
connector type in link_ksetting.
After FW exposed the connector type, driver translated the value to ethtool
definitions. However, as 0 is a valid value, before returning PORT_OTHER,
driver run the check of link mode in order to maintain backward
compatibility.
Cited patch added support to EXT mode. With both features (connector type
and EXT link modes) ,if connector_type read from FW is 0 and EXT mode is
set, driver mistakenly compare EXT link modes to non-EXT link mode.
Fixed that by skipping this comparison if we are in EXT mode, as connector
type value is valid in this scenario.
Fixes: 6a897372417e ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Before this commit the ndo always returned success.
Fix that.
Fixes: 1ab2068a4c66 ("net/mlx5: Implement vports admin state backup/restore")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When an ste hash table has too many collision we enlarge it
to a bigger hash table (rehash). Rehashing collision improvement
depends on the bytemask value. The more 1 bits we have in bytemask
means better spreading in the table.
Without this fix tables can grow in size without providing any
improvement which can lead to memory depletion and failures.
This patch will limit table rehash to reduce memory and improve
the performance.
Fixes: 41d07074154c ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The byte mask fields affect on the hash index distribution,
when the byte mask is zero, the hash calculation will always
be equal to the same index.
To avoid unneeded rehash of hash tables mark the table to skip
rehash.
This is needed by the next patch which will limit table rehash
to reduce memory consumption.
Fixes: 41d07074154c ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When creating a CQ, the CPU id is used for the vector value.
This would fail in-case the CPU id was higher than the maximum
vector value.
Fixes: 297cccebdc5a ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Mirred action parsing code in parse_tc_fdb_actions() first checks if
out_dev has same parent id, and only verifies that there is a pending encap
action that was parsed before. Recent change in vxlan module made function
netdev_port_same_parent_id() to return true when called for mlx5 eswitch
representor and vxlan device created explicitly on mlx5 representor
device (vxlan devices created with "external" flag without explicitly
specifying parent interface are not affected). With call to
netdev_port_same_parent_id() returning true, incorrect code path is chosen
and encap rules fail to offload because vxlan dev is not a valid eswitch
forwarding dev. Dmesg log of error:
[ 1784.389797] devices ens1f0_0 vxlan1 not on same switch HW, can't offload forwarding
In order to fix the issue, rearrange conditional in parse_tc_fdb_actions()
to check for pending encap action before checking if out_dev has the same
parent id.
Fixes: 0ce1822c2a08 ("vxlan: add adjacent link to limit depth level")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Current code uses the old method of prio encoding in
flow_cls_common_offload. Fix to follow the changes introduced in
commit ef01adae0e43 ("net: sched: use major priority number as hardware priority").
Fixes: fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Be sure to release the neighbour in case of failures after successful
route lookup.
Fixes: 101f4de9dd52 ("net/mlx5e: Move TC tunnel offloading code to separate source file")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When propagating IO errors back to userspace, one error path in
qeth_irq() currently returns '1' instead of a proper errno.
Fixes: 54daaca7024d ("s390/qeth: cancel cmd on early error")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The L2 bridgeport code uses the coarse 'conf_mutex' for guarding access
to its configuration state.
This can result in a deadlock when qeth_l2_stop_card() - called under the
conf_mutex - blocks on flush_workqueue() to wait for the completion of
pending bridgeport workers. Such workers would also need to aquire
the conf_mutex, stalling indefinitely.
Introduce a lock that specifically guards the bridgeport configuration,
so that the workers no longer need the conf_mutex.
Wrapping qeth_l2_promisc_to_bridge() in this fine-grained lock then also
fixes a theoretical race against a concurrent qeth_bridge_port_role_store()
operation.
Fixes: c0a2e4d10d93 ("s390/qeth: conclude all event processing before offlining a card")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add TC-MATCHALL classifier ingress offload support. The same actions
supported by existing TC-FLOWER offload can be applied to all incoming
traffic on the underlying interface.
Ensure the rule priority doesn't conflict with existing rules in the
TCAM. Only 1 ingress matchall rule can be active at a time on the
underlying interface.
v5:
- No change.
v4:
- Added check to ensure the matchall rule's prio doesn't conflict with
other rules in TCAM.
- Added logic to fill default mask for VIID, if none has been
provided, to prevent conflict with duplicate VIID rules.
- Used existing variables in private structure to fill VIID info,
instead of extracting the info manually.
v3:
- No change.
v2:
- Removed logic to fetch free index from end of TCAM. Must maintain
same ordering as in kernel.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only offload rule if it satisfies both of the following conditions:
1. The immediate previous rule has priority <= current rule's priority.
2. The immediate next rule has priority >= current rule's priority.
Also rework free entry fetch logic to search from end of TCAM, instead
of beginning, because higher indices have lower priority than lower
indices. This is similar to how TC auto generates priority values.
v5:
- Fixed commit message and comment to include comparison for equal
priority.
v4:
- Patch added in this version.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add TC-MATCHALL classifier offload with TC-POLICE action applied for
all outgoing traffic on the underlying interface. Split flow block
offload to support both egress and ingress classification.
For example, to rate limit all outgoing traffic to 1 Gbps:
$ tc qdisc add dev enp2s0f4 clsact
$ tc filter add dev enp2s0f4 egress matchall skip_sw \
action police rate 1Gbit burst 8Kbit
Note that skip_sw is important. Otherwise, both stack and hardware
will end up doing policing. Policing can't be shared across flow
blocks. Only 1 egress matchall rule can be active at a time on the
underlying interface.
v5:
- No change.
v4:
- Removed check to reject police offload if prio is not 1.
- Moved TC_SETUP_BLOCK code to separate function.
v3:
- Added check to reject police offload if prio is not 1.
- Assign block_shared variable only for TC_SETUP_BLOCK.
v2:
- Added check to reject flow block sharing for policers.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once every napi poll cycle, check if numa node is different than
the page pool's numa id, and update it using page_pool_update_nid().
Alternatively, we could have registered an irq affinity change handler,
but page_pool_update_nid() must be called from napi context anyways, so
the handler won't actually help.
Performance testing:
XDP drop/tx rate and TCP single/multi stream, on mlx5 driver
while migrating rx ring irq from close to far numa:
mlx5 internal page cache was locally disabled to get pure page pool
results.
CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz
NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G)
XDP Drop/TX single core:
NUMA | XDP | Before | After
---------------------------------------
Close | Drop | 11 Mpps | 10.9 Mpps
Far | Drop | 4.4 Mpps | 5.8 Mpps
Close | TX | 6.5 Mpps | 6.5 Mpps
Far | TX | 3.5 Mpps | 4 Mpps
Improvement is about 30% drop packet rate, 15% tx packet rate for numa
far test.
No degradation for numa close tests.
TCP single/multi cpu/stream:
NUMA | #cpu | Before | After
--------------------------------------
Close | 1 | 18 Gbps | 18 Gbps
Far | 1 | 15 Gbps | 18 Gbps
Close | 12 | 80 Gbps | 80 Gbps
Far | 12 | 68 Gbps | 80 Gbps
In all test cases we see improvement for the far numa case, and no
impact on the close numa case.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add dependency from TI_CPSW_SWITCHDEV.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPSW switchdev based driver which is operating in dual-emac mode by
default, thus working as 2 individual network interfaces. The Switch mode
can be enabled by configuring devlink driver parameter "switch_mode" to 1:
devlink dev param set platform/48484000.switch \
name switch_mode value 1 cmode runtime
This can be done regardless of the state of Port's netdevs - UP/DOWN, but
Port's netdev devices have to be UP before joining the bridge to avoid
overwriting of bridge configuration as CPSW switch driver completely
reloads its configuration when first Port changes its state to UP.
When the both interfaces joined the bridge - CPSW switch driver will start
marking packets with offload_fwd_mark flag unless "ale_bypass=0".
All configuration is implemented via switchdev API and notifiers.
Supported:
- SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS: BR_MCAST_FLOOD
- SWITCHDEV_ATTR_ID_PORT_STP_STATE
- SWITCHDEV_OBJ_ID_PORT_VLAN
- SWITCHDEV_OBJ_ID_PORT_MDB
- SWITCHDEV_OBJ_ID_HOST_MDB
Hence CPSW switchdev driver supports:
- FDB offloading
- MDB offloading
- VLAN filtering and offloading
- STP
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Part 1:
Introduce basic CPSW dual_mac driver (cpsw_new.c) which is operating in
dual-emac mode by default, thus working as 2 individual network interfaces.
Main differences from legacy CPSW driver are:
- optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in
addition to ALLMULTI (current port) instead of ALE_BYPASS. So, Ports in
promiscuous mode will keep possibility of mcast and vlan filtering, which
is provides significant benefits when ports are joined to the same bridge,
but without enabling "switch" mode, or to different bridges.
- learning disabled on ports as it make not too much sense for
segregated ports - no forwarding in HW.
- enabled basic support for devlink.
devlink dev show
platform/48484000.switch
devlink dev param show
platform/48484000.switch:
name ale_bypass type driver-specific
values:
cmode runtime value false
- "ale_bypass" devlink driver parameter allows to enable
ALE_CONTROL(4).BYPASS mode for debug purposes.
- updated DT bindings.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparatory patch to add support for a switchdev based cpsw driver,
move common functions to cpsw-priv.c so that they can be used across both
drivers.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A following patches introduce new CPSW switchdev driver which uses common
code with legacy CPSW driver. This will introduce build dependency between
CPSW switchdev and CPSW legacy drivers related to for_each_slave() and
cpsw_slave_index() - they can be compiled both, but only one of them will
be not functional depending in Kconfig settings due to duffrences in Slave
Ports indexes calculation.
To fix this make for_each_slave() local (it's used now only by legacy CPSW
driver) and convert cpsw_slave_index() to be a function pointer which is
assigned in probe. Driver to probe is defined by DT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A following patch introduces switchdev functionality, so modify
ALE engine VLANs/MDBs API:
- cpsw_ale_del_mcast(): update so it will remove only selected ports from
mcast port_mask or delete whole mcast record if !port_mask
- cpsw_ale_del_vlan(): update so it will remove only selected ports from
all VLAN record's masks or delete whole VLAN record if !port_mask
- add cpsw_ale_vlan_add_modify() to add or modify existing VLAN record's
masks
- add cpsw_ale_set_unreg_mcast() for enabling unreg mcast on port VLANs
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now untagged vlan traffic is not support on Host P0 port. This patch adds
in ALE context bitmap of VLANs for which Host P0 port bit set in Force
Untagged Packet Egress bitmask in VLANs ALE entries, and adds corresponding
check in VLAN incapsulation header parsing function cpsw_rx_vlan_encap().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clean CPSW ALE on init and intf restart (up/down) to avoid reading obsolete
or garbage entries from ALE table.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization
to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS,
causing failures if reset controller support is not enabled. E.g. on
r7s72100/rskrza1:
sh-eth e8203000.ethernet: MDIO init failed: -524
sh-eth: probe of e8203000.ethernet failed with error -524
Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb.
Fixes: 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization to constant")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 075e238d12c21c8bde700d21fb48be7a3aa80194.
Going to go with Geert's fix instead, which also has a
correct Fixes tag.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to hardware user manual, bits5~7 in register
HCLGE_MISC_VECTOR_INT_STS means reset interrupts status,
but HCLGE_RESET_INT_M is defined as bits0~2 now. So it
will make hclge_reset_err_handle() read the wrong reset
interrupt status.
This patch fixes this wrong bit mask.
Fixes: 2336f19d7892 ("net: hns3: check reset interrupt status when reset fails")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pm_runtime_put_autosuspend in probe will call runtime suspend to
disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM
is not defined, its implementation will be empty, then runtime
suspend will not be called.)
Therefore, we can call pm_runtime_get_sync to runtime resume it
first to enable clks, which matches the runtime suspend. (Only when
CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be
empty, then runtime resume will not be called.)
Then it is fine to disable clks without causing clock count mis-match.
Fixes: c43eab3eddb4 ("net: fec: add missed clk_disable_unprepare in remove")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modifying the link settings via phylink_ethtool_ksettings_set() and
phylink_ethtool_set_pauseparam() didn't always work as intended for
PHY based setups, as calling phylink_mac_config() would result in the
unresolved configuration being committed to the MAC, rather than the
configuration with the speed and duplex setting.
This would work fine if the update caused the link to renegotiate,
but if no settings have changed, phylib won't trigger a renegotiation
cycle, and the MAC will be left incorrectly configured.
Avoid calling phylink_mac_config() unless we are using an inband mode
in phylink_ethtool_ksettings_set(), and use phy_set_asym_pause() as
introduced in 4.20 to set the PHY settings in
phylink_ethtool_set_pauseparam().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the documentation on phylink's create and destroy functions to
explicitly state that the rtnl lock must not be held while calling
these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During performance testing, I found that one of my r8169 NICs suffered
a major performance loss, a 8168c model.
Running netperf's TCP_STREAM test didn't return the expected
throughput of > 900 Mb/s, but rather only about 22 Mb/s. Strange
enough, running the TCP_MAERTS and UDP_STREAM tests all returned with
throughput > 900 Mb/s, as did TCP_STREAM with the other r8169 NICs I can
test (either one of 8169s, 8168e, 8168f).
Bisecting turned up commit 93681cd7d94f83903cb3f0f95433d10c28a7e9a5,
"r8169: enable HW csum and TSO" as the culprit.
I added my 8168c version, RTL_GIGA_MAC_VER_22, to the code
special-casing the 8168evl as per the patch below. This fixed the
performance problem for me.
Fixes: 93681cd7d94f ("r8169: enable HW csum and TSO")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Semicolon is not required at the end of switch block. So, remove it.
Addresses coccinelle warning:
drivers/net/ethernet/chelsio/cxgb4/sge.c:2260:2-3: Unneeded semicolon
Fixes: 4846d5330daf ("cxgb4: add Tx and Rx path for ETHOFLD traffic")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the NXP LS1028A, there are 2 Ethernet links between the Felix switch
and the ENETC:
- eno2 <-> swp4, at 2.5G
- eno3 <-> swp5, at 1G
Only one of the above Ethernet port pairs can act as a DSA link for
tagging.
When adding initial support for the driver, it was tested only on the 1G
eno3 <-> swp5 interface, due to the necessity of using PHYLIB initially
(which treats fixed-link interfaces as emulated C22 PHYs, so it doesn't
support fixed-link speeds higher than 1G).
After making PHYLINK work, it appears that swp4 still can't act as CPU
port. So it looks like ocelot_set_cpu_port was being called for swp4,
but then it was called again for swp5, overwriting the CPU port assigned
in the DT.
It appears that when you call dsa_upstream_port for a port that is not
defined in the device tree (such as swp5 when using swp4 as CPU port),
its dp->cpu_dp pointer is not initialized by dsa_tree_setup_default_cpu,
and this trips up the following condition in dsa_upstream_port:
if (!cpu_dp)
return port;
So the moral of the story is: don't call dsa_upstream_port for a port
that is not defined in the device tree, and therefore its dsa_port
structure is not completely initialized (ds->num_ports is still 6).
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous commit had a bug where the last page in the memory range
could not be synced. This change fixes the behavior so that all the
required pages are synced.
Fixes: 9cfeeb576d49 ("gve: Fixes DMA synchronization")
Signed-off-by: Adi Suresh <adisuresh@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For our current users we don't expect pool objects to be writable from
the gpu.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 4f7af1948abc ("drm/i915: Support ro ppgtt mapped cmdparser shadow buffers")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191119150154.18249-1-matthew.auld@intel.com
(cherry picked from commit d18580b08b92ec4105eb0ede2d676e8b1f5a66c3)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Commit 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization
to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS,
causing failures if reset controller support is not enabled. E.g. on
r7s72100/rskrza1:
sh-eth e8203000.ethernet: MDIO init failed: -524
sh-eth: probe of e8203000.ethernet failed with error -524
Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb.
Fixes: 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization to constant")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Before returning NULL, put the sock first.
Cc: stable@vger.kernel.org
Fixes: cf1b2326b734 ("nbd: verify socket is supported during setup")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Sun Ke <sunke32@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When CONFIG_RESET_CONTROLLER is disabled, the
devm_reset_control_get_exclusive function returns -ENOTSUPP. This is not
handled in subsequent check and then the mdio device fails to probe.
When CONFIG_RESET_CONTROLLER is enabled, its code checks in OF for reset
device, and since it is not present, returns -ENOENT. -ENOENT is handled.
Add -ENOTSUPP also.
This happened to me when upgrading kernel on Turris Omnia. You either
have to enable CONFIG_RESET_CONTROLLER or use this patch.
Signed-off-by: Marek BehĂșn <marek.behun@nic.cz>
Fixes: 71dd6c0dff51b ("net: phy: add support for reset-controller")
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case where the call to phy_interface_is_rgmii returns zero
the variable ret is left uninitialized and this is returned at
the end of the function dp83869_configure_rgmii. Fix this by
returning 0 instead of the uninitialized value in ret.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 01db923e8377 ("net: phy: dp83869: Add TI dp83869 phy")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver forgets to disable the regulator in remove like what is done
in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
XDP_TX rings should not be limited by max_num_tx_rings_p_up.
To make sure total number of TX rings never exceed MAX_TX_RINGS,
add similar check in mlx4_en_alloc_tx_queue_per_tc(), where
a new value is assigned for num_up.
Fixes: 7e1dc5e926d5 ("net/mlx4_en: Limit the number of TX rings")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is especially beneficial during the NVRAM related firmware
commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND
flag gets set while waiting for firmware response, abort and return
error.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During loss of heartbeat, log this warning message.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For NVM params that are not supported in the current NVM
configuration, return the error as -EOPNOTSUPP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report health status update to devlink health reporter, once
reset is completed.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Linux driver is capable of being the master function to handle
resets, so we set the flag to let firmware know. Some other
drivers, such as DPDK, is not capable and will not set the flag.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If firmware supports hot reset, extend ETHTOOL_RESET to support
hot reset driver which does not require a driver reload after
ETHTOOL_RESET. The driver will go through the same coordinated
reset sequence as a firmware initiated fatal/non-fatal reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|