| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This update adds new regmap to support the latest EA silicon
which will be selected based on the chip and variant
information read from the device.
Signed-off-by: Carlos de Paula <me@carlosedp.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
By default the PMIC DA9063 2-wire interface is SMBus compliant. This
means the PMIC will automatically reset the interface when the clock
signal ceases for more than the SMBus timeout of 35 ms.
If the I2C driver / device is not capable of creating atomic I2C
transactions, a context change can cause a ceasing of the clock signal.
This can happen if for example a real-time thread is scheduled. Then
the DA9063 in SMBus mode will reset the 2-wire interface. Subsequently
a write message could end up in the wrong register. This could cause
unpredictable system behavior.
The DA9063 PMIC also supports an I2C compliant mode for the 2-wire
interface. This mode does not reset the interface when the clock
signal ceases. Thus the problem depicted above does not occur.
This patch tests for the bus functionality "I2C_FUNC_I2C". It can
reasonably be assumed that the bus cannot obey SMBus timings if
this functionality is set. SMBus commands most probably are emulated
in this case which is prone to the latency issue described above.
This patch enables the I2C bus mode if I2C_FUNC_I2C is set or
otherwise keeps the default SMBus mode.
Signed-off-by: Hubert Streidl <hubert.streidl@de.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This update adds new regmap tables to support the latest DA silicon
which will automatically be selected based on the chip and variant
information read from the device.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The current implementation performs checking in the i2c_probe()
function of the variant_code but does this immediately after the
containing struct has been initialised as all zero. This means the
check for variant code will always default to using the BB tables
and will never select AD. The variant code is subsequently set
by device_init() and later used by the RTC so really it's a little
fortunate this mismatch works.
This update adds raw I2C read access functionality to read the chip
and variant/revision information (common to all revisions) so that
it can subsequently correctly choose the proper regmap tables for
real initialisation.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
All preparational patches have been applied, we can now remove the
include file for platform_data. Yiha!
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Linux 5.2-rc4
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Those definitions are only used within the driver meanwhile, so put them
there.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Mismatch between what is found in the Datasheets for DA9063 and DA9063L
provided by Dialog Semiconductor, and the register names provided in the
MFD registers file. The changes are for the OTP (one-time-programming)
control registers. The two naming errors are OPT instead of OTP, and
COUNT instead of CONT (i.e. control).
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Covnert the headers of the source and include files to SPDX.
And fix some typos in the descriptions ("interrupt" instead of "I2C").
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Commit 1c892e38ce59 ("regulator: da9063: Handle less LDOs on DA9063L")
reordered the da9063_regulator_info[] array, but not the DA9063_ID_*
regulator ids and not the da9063_matches[] array, because ids are used
as indices in the array initializer. This mismatch between regulator id
and da9063_regulator_info[] array index causes the driver probe to fail
because constraints from DT are not applied to the correct regulator:
da9063 0-0058: Device detected (chip-ID: 0x61, var-ID: 0x50)
DA9063_BMEM: Bringing 900000uV into 3300000-3300000uV
DA9063_LDO9: Bringing 3300000uV into 2500000-2500000uV
DA9063_LDO1: Bringing 900000uV into 3300000-3300000uV
DA9063_LDO1: failed to apply 3300000-3300000uV constraint(-22)
This patch reorders the DA9063_ID_* as apparently intended, and with
them the entries in the da90630_matches[] array.
Fixes: 1c892e38ce59 ("regulator: da9063: Handle less LDOs on DA9063L")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add type for DA9063L, which is a reduced variant of the DA9063
without RTC block and with less regulators.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The model number stored in the struct da9063 is the same for all
variants of the da9063 since it is the chip ID, which is always
the same. Replace that with a separate identifier instead, which
allows us to discern the DA9063 variants by setting the type
based on either DT match or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The PMIC_DA9063 is a complete misnomer, it denotes the value of the
DA9063 chip ID register, so rename it as such. It is also the value
of chip ID register of DA9063L though, so drop the enum as all the
DA9063 "models" share the same chip ID and thus the distinction will
have to be made using DT or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Replace DA9063_NUM_IRQ macro which is not used anywhere with
plain ARRAY_SIZE().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Use devm_mfd_add_devices() instead of plain mfd_add_devices(), which
removes the need for da9063_device_exit() altogether and also for the
.remove callback in da9063-i2c.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Use devm_regmap_add_irq_chip() instead of plain regmap_add_irq_chip(),
which removes the need for da9063_irq_exit() altogether and also
fixes a bug in da9063_device_init() where the da9063_irq_exit() was
not called in a failpath.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Remove incorrect e-mail addresses from the copyright header and
MODULE_AUTHOR() macro. These e-mail addresses are no longer in use.
The author names have not been changed, only the e-mail addresses have
been deleted from the source files.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Fix a missing DVC_RDY interrupt mask in struct regmap_irq definition.
The original submission of this driver did not contain all interrupt
masking definitions in the struct regmap_irq contained in the file
da9063-irq.c
The solution is to add a DA9063_IRQ_DVC_RDY entry to enum da9063_irqs
list and to add the corresponding values to compensate for the missing
mask bit in the static const struct regmap_irq da9063_irqs[] table.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Adam Ward <adam.ward.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This adds OnKey driver support for DA9063.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add device tree support for DA9063 regulators; Real-Time Clock
and Watchdog.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add register definitions for DA9063 AD (0x3) silicon variant ID
the ability to choose the silicon variant at run-time using regmap
configuration. This patch also adds RTC support for the AD silicon
changes.
It adds both BB and AD support as regmap ranges and then makes the
distinction between the two tables at run-time. This allows both AD
and BB silicon variants to be supported at the same time.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch updates the register definitions for DA9063 to support the
production silicon variant code ID (0x5). These changes are not backwards
compatible with the previous register definitions and can only be used
with the production variant of DA9063.
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add the correct silicon variant code ID (0x5) to the driver. This
new code is the 'production' variant code ID for DA9063.
This patch will remove the older variant code ID which matches the
pre-production silicon ID (0x3) for the DA9063 chip.
There is also some small amount of correction done in this patch:
it splits the revision code and correctly names it according to
the hardware specification and moves the dev_info() call before
the variant ID test.
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds a regmap irqchip for DA9063 IRQs. It depends on
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap.git tags/regmap-irq-ack-mask
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This is MFD module providing access to registers and interrupts of DA906x
series PMIC. It is used by other functional modules, registered as MFD cells.
Driver uses regmap with paging to access extended register list. Register map
is divided into two pages, where the second page is used during initialisation.
This module provides support to following functional cells:
- Regulators
- RTC
- HWMON
- OnKey (power key misc input device)
- Vibration (force-feedback input device)
- Watchdog
- LEDs
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch adds register definitions for the DA9063 PMIC. They will be used
by the following DA9063 mfd core driver and functional module drivers.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
Carlos de Paula
Hubert Streidl
Adam Thomson
Wolfram Sang
Mark Brown
Thomas Gleixner
Steve Twiss
Philipp Zabel
Marek Vasut
Krystian Garbaciak