aboutsummaryrefslogtreecommitdiffstats
path: root/include/linux/mtd (follow)
AgeCommit message (Collapse)AuthorFilesLines
2012-12-03mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus widthMatthieu CASTET1-0/+7
The driver call nand_scan_ident in 8 bit mode, then readid or onfi detection are done (and detect bus width). The driver should update its bus width before calling nand_scan_tail. This work because readid and onfi are read work 8 byte mode. Note that nand_scan_ident send command (NAND_CMD_RESET, NAND_CMD_READID, NAND_CMD_PARAM), address and read data The ONFI specificication is not very clear for x16 device if high byte of address should be driven to 0, but according to [1] it should be ok to not drive it during autodetection. [1] 3.3.2. Target Initialization [...] The Read ID and Read Parameter Page commands only use the lower 8-bits of the data bus. The host shall not issue commands that use a word data width on x16 devices until the host determines the device supports a 16-bit data bus width in the parameter page. Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-21mtd: mtd_blkdevs: Replace request handler kthread with a workqueueEzequiel Garcia1-1/+3
By replacing a kthread with a workqueue, the code is now a bit clearer. There's also a slight reduction of code size (numbers apply for x86): Before: text data bss dec hex filename 3248 36 0 3284 cd4 drivers/mtd/mtd_blkdevs.o After: text data bss dec hex filename 3150 36 0 3186 c72 drivers/mtd/mtd_blkdevs.o Due to lack of real hardware, tests have been performed on an emulated environment with mtdswap and mtdblock over nandsim devices. Some real testing should be done, before merging this patch. Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-16mtd: uninitialized variable warning in map.hArnd Bergmann1-1/+1
The map_word_load() function initializes exactly as many words in the buffer as required, but gcc cannot figure this out and gives a misleading warning. Marking the local variable as uninitialized_var shuts up that warning. Without this patch, building acs5k_defconfig results in: drivers/mtd/chips/cfi_cmdset_0002.c: In function 'cfi_amdstd_panic_write': include/linux/mtd/map.h:331:11: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized] drivers/mtd/chips/cfi_cmdset_0002.c: In function 'cfi_amdstd_write_words': include/linux/mtd/map.h:331:11: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized] drivers/mtd/chips/cfi_cmdset_0001.c: In function 'cfi_intelext_write_words': include/linux/mtd/map.h:331:11: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized] Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-16mtd: diskonchip: use inline functions for DocRead/DocWriteArnd Bergmann1-4/+18
The diskonchip drivers traditionally use home-grown macros for doing MMIO accesses, which cause a lot of warnings, at least on ARM machines: drivers/mtd/devices/doc2000.c: In function 'doc_write': drivers/mtd/devices/doc2000.c:854:5: warning: value computed is not used [-Wunused-value] drivers/mtd/devices/doc2000.c: In function 'doc_erase': drivers/mtd/devices/doc2000.c:1123:5: warning: value computed is not used [-Wunused-value drivers/mtd/nand/diskonchip.c: In function 'doc2000_read_byte': drivers/mtd/nand/diskonchip.c:318:3: warning: value computed is not used [-Wunused-value] A nicer solution is to use the architecture-defined I/O accessors. Here, we use the __raw_readl/__raw_writel style, instead of the proper readl/writel ones, in order to preserve the odd semantics of the existing macros that have their own barrier implementation and no byte swap. It would be nice to fix this properly and use the correct accessors as well as make the word size independent from the architecture, but I guess the hardware is obsolete enough that we should better not mess the driver an more than necessary. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-15mtd: map: Fix compilation warningViresh Kumar1-1/+1
This patch is an attempt to fix following compilation warning. In file included from drivers/mtd/chips/cfi_cmdset_0001.c:35:0: drivers/mtd/chips/cfi_cmdset_0001.c: In function 'cfi_intelext_write_words': include/linux/mtd/map.h:331:11: warning: 'r.x[0]' may be used uninitialized in this function [-Wmaybe-uninitialized] I could have used uninitialized_var() too, but didn't used it as the final else part of map_word_load() is missing. So there is a chance that it might be passed uninitialized. Better initialize to zero. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-15mtd: Fix kernel-doc content to avoid warning.Robert P. J. Day1-2/+2
Add missing colons to fix kernel-doc generation warnings. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-15mtd: sh_flctl: Add DMA capabiltyBastian Hecht1-0/+12
The code probes if DMA channels can get allocated and tears them down at removal/failure if needed. If available it uses them to transfer the data part (not ECC). On failure we fall back to PIO mode. Based on Guennadi Liakhovetski's code from the sh_mmcif driver. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-15mtd: sh_flctl: Minor cleanupsBastian Hecht1-1/+1
Some small fixes to avoid sparse and smatch complain. Other cosmetic fixes as well. - Change of the type of the member index in struct sh_flctl from signed to unsigned. We use index by addressing array members, so unsigned is more concise here. Adapt functions relying on sh_flctl::index. - Remove a blurring cast in write_fiforeg(). - Apply consistent naming scheme when refering to the data buffer. - Shorten some unnecessarily verbose functions. - Remove spaces at start of lines. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-15mtd: gpmi: remove unneccessary headerHuang Shijie1-68/+0
The whole gpmi-nand driver has turned to pure devicetree supported. So the linux/mtd/gpmi-nand.h is not neccessary now. Just remove it, and move some macros to the gpmi-nand driver itself. Signed-off-by: Huang Shijie <shijie8@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-15mtd: nand: Increase the ecc placement locations to 640Vipin Kumar1-1/+1
Few devices like H27UBG8T2CTR have a writesize/oobsize of 8KB/640B. This means that the maximum oobsize has gone up to 640 bytes and consequently the maximum ecc placement locations have also gone up to 640. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-15mtd: fsmc_nand: pass the ale and cmd resource via resourceJean-Christophe PLAGNIOL-VILLARD1-3/+0
Do not use the platform_data to pass resource and be smart in the drivers. Just pass it via resource Switch to devm_request_and_ioremap at the sametime Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-By: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-10-09Merge tag 'disintegrate-mtd-20121009' of git://git.infradead.org/users/dhowells/linux-headersDavid Woodhouse1-1/+2
UAPI Disintegration 2012-10-09 Conflicts: MAINTAINERS arch/arm/configs/bcmring_defconfig arch/arm/mach-imx/clk-imx51-imx53.c drivers/mtd/nand/Kconfig drivers/mtd/nand/bcm_umi_nand.c drivers/mtd/nand/nand_bcm_umi.h drivers/mtd/nand/orion_nand.c
2012-09-29mtd: nand: increase max OOB size to 640Brian Norris1-1/+1
Some Hynix and Samsung MLC NAND have 640B OOB size. Sooner or later, we should dynamically allocate the buffers that use these macros. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-09-29mtd: add helpers to get the supportted ONFI timing modeHuang Shijie1-0/+25
add onfi_get_async_timing_mode() to get the supportted asynchronous timing mode. add onfi_get_sync_timing_mode() to get the supportted synchronous timing mode. Also add the neccessary macros : the timing modes. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-09-29mtd: add helpers to set/get features for ONFI nandHuang Shijie1-0/+14
Add the set-features(0xef)/get-features(0xee) helpers for ONFI nand. Also add the necessary macros. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-09-29mtd: nand: expand description of read_page method in comment headerMike Dunn1-2/+4
In the absence of any formal documentation of the nand interface, I thought this patch to the header file might be helpful. Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-09-29mtd: nand: Added a device flag for subpage read supportJeff Westfahl1-3/+4
Added a NAND device flag for subpage read support. Previously this was hard coded based on large page and soft ECC. Updated base NAND driver to use the new subpage read flag if the NAND is large page and soft ECC. Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com> Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-09-29mtd: fix kernel-doc warning in include/linux/mtd/nand.hRandy Dunlap1-0/+1
Fix kernel-doc warning in <linux/mtd/nand.h>: Warning(include/linux/mtd/nand.h:659): No description found for parameter 'read_byte' Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-09-29mtd: kill MTD_NAND_VERIFY_WRITEHuang Shijie1-3/+0
Just as Artem suggested: "Both UBI and JFFS2 are able to read verify what they wrote already. There are also MTD tests which do this verification. So I think there is no reason to keep this in the NAND layer, let alone wasting RAM in the driver to support this feature. Besides, it does not work for sub-pages and many drivers have it broken. It hurts more than it provides benefits." So kill MTD_NAND_VERIFY_WRITE entirely. Signed-off-by: Huang Shijie <shijie8@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-09-29mtd: nand: allow NAND_NO_SUBPAGE_WRITE to be set from driverBrian Norris1-3/+0
The NAND_CHIPOPTIONS_MSK has limited utility and is causing real bugs. It silently masks off at least one flag that might be set by the driver (NAND_NO_SUBPAGE_WRITE). This breaks the GPMI NAND driver and possibly others. Really, as long as driver writers exercise a small amount of care with NAND_* options, this mask is not necessary at all; it was only here to prevent certain options from accidentally being set by the driver. But the original thought turns out to be a bad idea occasionally. Thus, kill it. Note, this patch fixes some major gpmi-nand breakage. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Tested-by: Huang Shijie <shijie8@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-09-29mtd: lpc32xx_mlc: Make driver independent of AMBA DMA engine driverRoland Stigge1-0/+20
This patch makes the MLC NAND driver independent of the single AMBA DMA engine driver by using the platform data provided dma_filter callback. Signed-off-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-09-29mtd: lpc32xx_slc: Make driver independent of AMBA DMA engine driverRoland Stigge1-0/+20
This patch makes the SLC NAND driver independent of the single AMBA DMA engine driver by using the platform data provided dma_filter callback. Signed-off-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-09-04mtd: mtdparts: introduce mtd_get_device_sizeRichard Genoud1-0/+1
'mtd_get_device_size()' returns the size of the whole MTD device, that is the mtd_info master size. This will be used by UBI to calculate the maximum number of bad blocks (MBB) on a MTD device. Artem: amended the patch a bit. Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-09-04mtd: mark mtd_is_partition argument as constantRichard Genoud1-1/+1
'struct mtd_info' is not modified by 'mtd_is_partition()' so it can be marked as "const". Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-07-06mtd: Better comment NAND_BBT_NO_OOBShmulik Ladkani1-1/+4
Amend the comment to reflect the fact NAND_BBT_NO_OOB refers to the location of the bad block table marker. Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06mtd: nand: teach write_page and write_page_raw return an error codeJosh Wu1-2/+2
There is an implemention of hardware ECC write page function which may return an error indication. For instance, using Atmel HW PMECC to write one page into a nand flash, the hardware engine will compute the BCH ecc code for this page. so we need read a the status register to theck whether the ecc code is generated. But we cannot assume the status register always can be ready, for example, incorrect hardware configuration or hardware issue, in such case we need write_page() to return a error code. Since the definition of 'write_page' function in struct nand_ecc_ctrl is 'void'. So this patch will: 1. add return 'int' value for 'write_page' function. 2. to be consitent, add return 'int' value for 'write_page_raw' fuctions too. 3. add code to test the return value, and if negative, indicate an error happend when write page with ECC. 4. fix the compile warning in all impacted nand flash driver. Note: I couldn't compile-test all of these easily, as some had ARCH dependencies. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06mtd: nand: kill NAND_NO_READRDYBrian Norris1-6/+0
According to its documentation, the NAND_NO_READRDY option is always used when autoincrement is not supported. Autoincrement support was recently dropped, so we can drop this options as well (defaulting to "no read ready check"). Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06mtd: nand: remove NAND_BBT_SEARCH optionBrian Norris1-2/+0
This option was never used and isn't currently used. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06mtd: nand: add Eon Silicon Solutions manufacturer IDBrian Norris1-0/+1
Eon's new NAND flash: EN27LN1G08. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06mtd: sh_flctl: Restructure the hardware ECC handlingBastian Hecht1-3/+7
There are multiple reasons for a rewrite: - a race exists: when _4ECCEND is set, _4ECCFA may become true too meanwhile, which is lost and a non-correctable error is treated as correctable. - the ECC statistics don't get properly propagated to the base code. - empty pages would get marked as corrupted The rewrite resolves the issues and I hope it gives a more explicit code flow structure. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06mtd: sh_flctl: Use different OOB layoutBastian Hecht1-4/+0
The flctl hardware has changed and a new OOB layout must be adapted for 2KiB page size NAND chips when using hardware ECC. The related bit fields ECCPOS[0-2] are gone — the bits are marked as reserved now in the datasheet. As there are no official users of the hardware ECC so far, they are completely removed. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06mtd: sh_flctl: Add support for error IRQBastian Hecht1-0/+9
When the data transfer between the controller and the NAND chip fails, we now get notified. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06mtd: move mtd_read_oob() definition out of mtd.hBrian Norris1-8/+1
mtd_read_oob() will be expanded a little, so don't leave it in the header as a static inline function. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-06-01Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtdLinus Torvalds3-17/+27
Pull mtd update from David Woodhouse: - More robust parsing especially of xattr data in JFFS2 - Updates to mxc_nand and gpmi drivers to support new boards and device tree - Improve consistency of information about ECC strength in NAND devices - Clean up partition handling of plat_nand - Support NAND drivers without dedicated access to OOB area - BCH hardware ECC support for OMAP - Other fixes and cleanups, and a few new device IDs Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to added include files next to each other. * tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits) mtd: mxc_nand: move ecc strengh setup before nand_scan_tail mtd: block2mtd: fix recursive call of mtd_writev mtd: gpmi-nand: define ecc.strength mtd: of_parts: fix breakage in Kconfig mtd: nand: fix scan_read_raw_oob mtd: docg3 fix in-middle of blocks reads mtd: cfi_cmdset_0002: Slight cleanup of fixup messages mtd: add fixup for S29NS512P NOR flash. jffs2: allow to complete xattr integrity check on first GC scan jffs2: allow to discriminate between recoverable and non-recoverable errors mtd: nand: omap: add support for hardware BCH ecc ARM: OMAP3: gpmc: add BCH ecc api and modes mtd: nand: check the return code of 'read_oob/read_oob_raw' mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw' mtd: m25p80: Add support for Winbond W25Q80BW jffs2: get rid of jffs2_sync_super jffs2: remove unnecessary GC pass on sync jffs2: remove unnecessary GC pass on umount jffs2: remove lock_super mtd: gpmi: add gpmi support for mx6q ...
2012-05-21UBI: modify ubi_wl_flush function to clear work queue for a lnumJoel Reardon1-0/+1
This patch modifies ubi_wl_flush to force the erasure of particular volume id / logical eraseblock number pairs. Previous functionality is preserved when passing UBI_ALL for both values. The locations where ubi_wl_flush were called are appropriately changed: ubi_leb_erase only flushes for the erased LEB, and ubi_create_volume forces only flushing for its volume id. External code can call this new feature via the new function ubi_flush() added to kapi.c, which simply passes through to ubi_wl_flush(). This was tested by disabling the call to do_work in ubi thread, which results in the work queue remaining unless explicitly called to remove. UBIFS was changed to call ubifs_leb_change 50 times for four different LEBs. Then the new function was called to clear the queue: passing wrong volume ids / lnum, correct ones, and finally UBI_ALL for both to ensure it was finally all cleard. The work queue was dumped each time and the selective removal of the particular LEB numbers was observed. Extra checks were enabled and ubifs's integck was also run. Finally, the drive was repeatedly filled and emptied to ensure that the queue was cleared normally. Artem: amended the patch. Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-05-21UBI: introduce UBI_ALL constantArtem Bityutskiy1-0/+3
Joel will use it in his 'ubi_flush()' extention to specify all eraseblocks. Also amend the comment for UBI_UNKNOWN - it is used beyond attaching info structure now. Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-05-20UBI: Kill data type hintRichard Weinberger1-24/+3
We do not need this feature and to our shame it even was not working and there was a bug found very recently. -- Artem Bityutskiy Without the data type hint UBI2 (fastmap) will be easier to implement. Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-05-13mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'Shmulik Ladkani1-3/+2
As of [mtd: nand: remove autoincrement 'sndcmd' code], the NAND_CMD_READ0 command is issued unconditionally. Thus, read_oob/read_oob_raw's 'sndcmd' argument is no longer needed, as well as their return code. Remove the 'sndcmd' parameter, and set the return code to 0. Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13mtd: gpmi: add device tree support to gpmi-nandHuang Shijie1-4/+4
This patch just adds the DT support to gpmi-nand. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Huang Shijie <shijie8@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13mtd: nand: add 'oob_required' argument to NAND {read,write}_page interfacesBrian Norris1-5/+6
New NAND controllers can perform read/write via HW engines which don't expose OOB data in their DMA mode. To reflect this, we should rework the nand_chip / nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB data in the nand_chip.oob_poi buffer. A better interface includes a boolean argument that explicitly tells the callee when OOB data is requested by the calling layer (for reading/writing to/from nand_chip.oob_poi). This patch adds the 'oob_required' parameter to each relevant {read,write}_page interface; all 'oob_required' parameters are left unused for now. The next patch will set the parameter properly in the nand_base.c callers, and follow-up patches will make use of 'oob_required' in some of the callee functions. Note that currently, there is no harm in ignoring the 'oob_required' parameter and *always* utilizing nand_chip.oob_poi, but there can be performance/complexity/design benefits from avoiding filling oob_poi in the common case. I will try to implement this for some drivers which can be ported easily. Note: I couldn't compile-test all of these easily, as some had ARCH dependencies. [dwmw2: Merge later 1/0 vs. true/false cleanup] Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by: Jiandong Zheng <jdzheng@broadcom.com> Acked-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13mtd: add read_byte support to plat_nandJohn Crispin1-0/+1
Lantiq SoCs have a External Bus Unit (EBU) that is used to attach MTD media. As we need to co-exist with PCI on the same bus, certain swapping settings must be applied. Similar to the NOR map driver we need to apply a fix to make NAND work. The easiest way is to use byte reads. Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13mtd: nand: kill NAND_NO_AUTOINCR optionBrian Norris1-4/+1
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13mtd: driver _read() returns max_bitflips; mtd_read() returns -EUCLEANMike Dunn1-0/+3
The drivers' _read() method, absent an error, returns a non-negative integer indicating the maximum number of bit errors that were corrected in any one region comprising an ecc step. MTD returns -EUCLEAN if this is >= bitflip_threshold, 0 otherwise. If bitflip_threshold is zero, the comparison is not made since these devices lack ECC and always return zero in the non-error case (thanks Brian)¹. Note that this is a subtle change to the driver interface. This and the preceding patches in this set were tested with ubi on top of the nandsim and docg4 devices, running the ubi test io_basic from mtd-utils. ¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040468.html Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Brian Norris <computersforpeace@gmail.com> Ivan Djelic <ivan.djelic@parrot.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13mtd: bitflip_threshold added to mtd_info and sysfsMike Dunn1-0/+9
An element 'bitflip_threshold' is added to struct mtd_info, and also exposed as a read/write variable in sysfs. This will be used to determine whether or not mtd_read() returns -EUCLEAN or 0 (absent a hard error). If the driver leaves it as zero, mtd will set it to a default value of ecc_strength. This v2 adds the line that propagates bitflip_threshold from the master to the partitions - thanks Ivan¹. ¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040900.html Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13mtd: ecc_strength is at ecc step granularityMike Dunn1-1/+1
ecc_strength element of mtd_info will be the strength of one ecc step, not of the entire writesize, as was previously planned. This is the appropriate way because, as was pointed out¹, bit errors in excess of the strength of one step can cause a hard error if they all occur within the same ecc region. ¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040313.html Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-30Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6Linus Torvalds8-378/+291
Pull MTD changes from David Woodhouse: - Artem's cleanup of the MTD API continues apace. - Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others. - More work on DiskOnChip G3, new driver for DiskOnChip G4. - Clean up debug/warning printks in JFFS2 to use pr_<level>. Fix up various trivial conflicts, largely due to changes in calling conventions for things like dmaengine_prep_slave_sg() (new inline wrapper to hide new parameter, clashing with rewrite of previously last parameter that used to be an 'append' flag, and is now a bitmap of 'unsigned long flags'). (Also some header file fallout - like so many merges this merge window - and silly conflicts with sparse fixes) * tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits) mtd: docg3 add protection against concurrency mtd: docg3 refactor cascade floors structure mtd: docg3 increase write/erase timeout mtd: docg3 fix inbound calculations mtd: nand: gpmi: fix function annotations mtd: phram: fix section mismatch for phram_setup mtd: unify initialization of erase_info->fail_addr mtd: support ONFI multi lun NAND mtd: sm_ftl: fix typo in major number. mtd: add device-tree support to spear_smi mtd: spear_smi: Remove default partition information from driver mtd: Add device-tree support to fsmc_nand mtd: fix section mismatch for doc_probe_device mtd: nand/fsmc: Remove sparse warnings and errors mtd: nand/fsmc: Add DMA support mtd: nand/fsmc: Access the NAND device word by word whenever possible mtd: nand/fsmc: Use dev_err to report error scenario mtd: nand/fsmc: Use devm routines mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform mtd: fsmc_nand: add pm callbacks to support hibernation ...
2012-03-28Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_systemLinus Torvalds1-1/+1
Pull "Disintegrate and delete asm/system.h" from David Howells: "Here are a bunch of patches to disintegrate asm/system.h into a set of separate bits to relieve the problem of circular inclusion dependencies. I've built all the working defconfigs from all the arches that I can and made sure that they don't break. The reason for these patches is that I recently encountered a circular dependency problem that came about when I produced some patches to optimise get_order() by rewriting it to use ilog2(). This uses bitops - and on the SH arch asm/bitops.h drags in asm-generic/get_order.h by a circuituous route involving asm/system.h. The main difficulty seems to be asm/system.h. It holds a number of low level bits with no/few dependencies that are commonly used (eg. memory barriers) and a number of bits with more dependencies that aren't used in many places (eg. switch_to()). These patches break asm/system.h up into the following core pieces: (1) asm/barrier.h Move memory barriers here. This already done for MIPS and Alpha. (2) asm/switch_to.h Move switch_to() and related stuff here. (3) asm/exec.h Move arch_align_stack() here. Other process execution related bits could perhaps go here from asm/processor.h. (4) asm/cmpxchg.h Move xchg() and cmpxchg() here as they're full word atomic ops and frequently used by atomic_xchg() and atomic_cmpxchg(). (5) asm/bug.h Move die() and related bits. (6) asm/auxvec.h Move AT_VECTOR_SIZE_ARCH here. Other arch headers are created as needed on a per-arch basis." Fixed up some conflicts from other header file cleanups and moving code around that has happened in the meantime, so David's testing is somewhat weakened by that. We'll find out anything that got broken and fix it.. * tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits) Delete all instances of asm/system.h Remove all #inclusions of asm/system.h Add #includes needed to permit the removal of asm/system.h Move all declarations of free_initmem() to linux/mm.h Disintegrate asm/system.h for OpenRISC Split arch_align_stack() out from asm-generic/system.h Split the switch_to() wrapper out of asm-generic/system.h Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h Create asm-generic/barrier.h Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h Disintegrate asm/system.h for Xtensa Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt] Disintegrate asm/system.h for Tile Disintegrate asm/system.h for Sparc Disintegrate asm/system.h for SH Disintegrate asm/system.h for Score Disintegrate asm/system.h for S390 Disintegrate asm/system.h for PowerPC Disintegrate asm/system.h for PA-RISC Disintegrate asm/system.h for MN10300 ...
2012-03-28Remove all #inclusions of asm/system.hDavid Howells1-1/+0
Remove all #inclusions of asm/system.h preparatory to splitting and killing it. Performed with the following command: perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *` Signed-off-by: David Howells <dhowells@redhat.com>
2012-03-28Add #includes needed to permit the removal of asm/system.hDavid Howells1-0/+1
asm/system.h is a cause of circular dependency problems because it contains commonly used primitive stuff like barrier definitions and uncommonly used stuff like switch_to() that might require MMU definitions. asm/system.h has been disintegrated by this point on all arches into the following common segments: (1) asm/barrier.h Moved memory barrier definitions here. (2) asm/cmpxchg.h Moved xchg() and cmpxchg() here. #included in asm/atomic.h. (3) asm/bug.h Moved die() and similar here. (4) asm/exec.h Moved arch_align_stack() here. (5) asm/elf.h Moved AT_VECTOR_SIZE_ARCH here. (6) asm/switch_to.h Moved switch_to() here. Signed-off-by: David Howells <dhowells@redhat.com>
2012-03-27mtd: add device-tree support to spear_smiStefan Roese1-0/+5
This patch adds support to configure the SPEAr SMI driver via device-tree instead of platform_data. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.