aboutsummaryrefslogtreecommitdiffstats
path: root/include/net/bluetooth/hci.h (follow)
AgeCommit message (Collapse)AuthorFilesLines
2020-01-15Bluetooth: Add definitions for CIS connectionsLuiz Augusto von Dentz1-1/+158
These adds the HCI definitions for handling CIS connections along with ISO data packets. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-04Bluetooth: Add support for LE PHY Update Complete eventLuiz Augusto von Dentz1-0/+8
This handles LE PHY Update Complete event and store both tx_phy and rx_phy into hci_conn. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-07-06Bluetooth: Add support for LE ping featureSpoorthi Ravishankar Koppad1-0/+20
Changes made to add HCI Write Authenticated Payload timeout command for LE Ping feature. As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94, the following code changes implements HCI Write Authenticated Payload timeout command for LE Ping feature. Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-05-05Bluetooth: Ignore CC events not matching the last HCI commandJoão Paulo Rechi Vita1-0/+1
This commit makes the kernel not send the next queued HCI command until a command complete arrives for the last HCI command sent to the controller. This change avoids a problem with some buggy controllers (seen on two SKUs of QCA9377) that send an extra command complete event for the previous command after the kernel had already sent a new HCI command to the controller. The problem was reproduced when starting an active scanning procedure, where an extra command complete event arrives for the LE_SET_RANDOM_ADDR command. When this happends the kernel ends up not processing the command complete for the following commmand, LE_SET_SCAN_PARAM, and ultimately behaving as if a passive scanning procedure was being performed, when in fact controller is performing an active scanning procedure. This makes it impossible to discover BLE devices as no device found events are sent to userspace. This problem is reproducible on 100% of the attempts on the affected controllers. The extra command complete event can be seen at timestamp 27.420131 on the btmon logs bellow. Bluetooth monitor ver 5.50 = Note: Linux version 5.0.0+ (x86_64) 0.352340 = Note: Bluetooth subsystem version 2.22 0.352343 = New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0) [hci0] 0.352344 = Open Index: 80:C5:F2:8F:87:84 [hci0] 0.352345 = Index Info: 80:C5:F2:8F:87:84 (Qualcomm) [hci0] 0.352346 @ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.352347 @ MGMT Open: btmon (privileged) version 1.14 {0x0002} 0.352366 @ MGMT Open: btmgmt (privileged) version 1.14 {0x0003} 27.302164 @ MGMT Command: Start Discovery (0x0023) plen 1 {0x0003} [hci0] 27.302310 Address type: 0x06 LE Public LE Random < HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #1 [hci0] 27.302496 Address: 15:60:F2:91:B2:24 (Non-Resolvable) > HCI Event: Command Complete (0x0e) plen 4 #2 [hci0] 27.419117 LE Set Random Address (0x08|0x0005) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #3 [hci0] 27.419244 Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) > HCI Event: Command Complete (0x0e) plen 4 #4 [hci0] 27.420131 LE Set Random Address (0x08|0x0005) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #5 [hci0] 27.420259 Scanning: Enabled (0x01) Filter duplicates: Enabled (0x01) > HCI Event: Command Complete (0x0e) plen 4 #6 [hci0] 27.420969 LE Set Scan Parameters (0x08|0x000b) ncmd 1 Status: Success (0x00) > HCI Event: Command Complete (0x0e) plen 4 #7 [hci0] 27.421983 LE Set Scan Enable (0x08|0x000c) ncmd 1 Status: Success (0x00) @ MGMT Event: Command Complete (0x0001) plen 4 {0x0003} [hci0] 27.422059 Start Discovery (0x0023) plen 1 Status: Success (0x00) Address type: 0x06 LE Public LE Random @ MGMT Event: Discovering (0x0013) plen 2 {0x0003} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) @ MGMT Event: Discovering (0x0013) plen 2 {0x0002} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) @ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-26Bluetooth: Add quirk for reading BD_ADDR from fwnode propertyMatthias Kaehlcke1-0/+12
Add HCI_QUIRK_USE_BDADDR_PROPERTY to allow controllers to retrieve the public Bluetooth address from the firmware node property 'local-bd-address'. If quirk is set and the property does not exist or is invalid the controller is marked as unconfigured. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Tested-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27Bluetooth: Add definitions and track LE resolve list modificationAnkit Navik1-0/+14
Add the definitions for adding entries to the LE resolve list and removing entries from the LE resolve list. When the LE resolve list gets changed via HCI commands make sure that the internal storage of the resolve list entries gets updated. Signed-off-by: Ankit Navik <ankit.p.navik@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-10Bluetooth: Add definitions for LE set address resolutionAnkit Navik1-0/+3
Add the definitions for LE address resolution enable HCI commands. When the LE address resolution enable gets changed via HCI commands make sure that flag gets updated. Signed-off-by: Ankit Navik <ankit.p.navik@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-06Bluetooth: btqca: Introduce HCI_EV_VENDOR and use itMarcel Holtmann1-0/+2
Using HCI_VENDOR_PKT for vendor specific events does work since it has also the value 0xff, but it is actually the packet type indicator constant and not the event constant. So introduce HCI_EV_VENDOR and use it. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2018-07-30Bluetooth: Add new quirk for non-persistent setup settingsSean Wang1-0/+9
Add a new quirk HCI_QUIRK_NON_PERSISTENT_SETUP allowing that a quirk that runs setup() after every open() and not just after the first open(). Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Implement secondary advertising on different PHYsJaganath Kanakkassery1-0/+4
This patch adds support for advertising in primary and secondary channel on different PHYs. User can add the phy preference in the flag based on which phy type will be added in extended advertising parameter would be set. @ MGMT Command: Add Advertising (0x003e) plen 11 Instance: 1 Flags: 0x00000200 Advertise in CODED on Secondary channel Duration: 0 Timeout: 0 Advertising data length: 0 Scan response length: 0 < HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2 Extended advertising: Disabled (0x00) Number of sets: Disable all sets (0x00) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2 Status: Success (0x00) < HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25 Handle: 0x00 Properties: 0x0000 Min advertising interval: 1280.000 msec (0x0800) Max advertising interval: 1280.000 msec (0x0800) Channel map: 37, 38, 39 (0x07) Own address type: Random (0x01) Peer address type: Public (0x00) Peer address: 00:00:00:00:00:00 (OUI 00-00-00) Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00) TX power: 127 dbm (0x7f) Primary PHY: LE Coded (0x03) Secondary max skip: 0x00 Secondary PHY: LE Coded (0x03) SID: 0x00 Scan request notifications: Disabled (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Handle ADv set terminated eventJaganath Kanakkassery1-0/+8
This event comes after connection complete event for incoming connections. Since we now have different random address for each instance, conn resp address is assigned from this event. As of now only connection part is handled as we are not enabling duration or max num of events while starting ext adv. Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Implement Set ADV set random addressJaganath Kanakkassery1-0/+6
This basically sets the random address for the adv instance Random address can be set only if the instance is created which is done in Set ext adv param. Random address and rpa expire timer and flags have been added to adv instance which will be used when the respective instance is scheduled. This introduces a hci_get_random_address() which returns the own address type and random address (rpa or nrpa) based on the instance flags and hdev flags. New function is required since own address type should be known before setting adv params but address can be set only after setting params. < HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7 Advertising handle: 0x00 Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56) > HCI Event: Command Complete (0x0e) plen 4 LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Implement disable and removal of adv instanceJaganath Kanakkassery1-0/+2
If ext adv is enabled then use ext adv to disable as well. Also remove the adv set during LE disable. < HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2 Extended advertising: Disabled (0x00) Number of sets: Disable all sets (0x00) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Use Set ext adv/scan rsp data if controller supportsJaganath Kanakkassery1-0/+22
This patch implements Set Ext Adv data and Set Ext Scan rsp data if controller support extended advertising. Currently the operation is set as Complete data and fragment preference is set as no fragment < HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 35 Handle: 0x00 Operation: Complete extended advertising data (0x03) Fragment preference: Minimize fragmentation (0x01) Data length: 0x15 16-bit Service UUIDs (complete): 2 entries Heart Rate (0x180d) Battery Service (0x180f) Name (complete): Test LE Company: Google (224) Data: 0102 > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Data (0x08|0x0037) ncmd 1 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Impmlement extended adv enableJaganath Kanakkassery1-0/+39
This patch basically replaces legacy adv with extended adv based on the controller support. Currently there is no design change. ie only one adv set will be enabled at a time. This also adds tx_power in instance and store whatever returns from Set_ext_parameter, use the same in adv data as well. For instance 0 tx_power is stored in hdev only. < HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25 Handle: 0x00 Properties: 0x0010 Use legacy advertising PDUs: ADV_NONCONN_IND Min advertising interval: 1280.000 msec (0x0800) Max advertising interval: 1280.000 msec (0x0800) Channel map: 37, 38, 39 (0x07) Own address type: Random (0x01) Peer address type: Public (0x00) Peer address: 00:00:00:00:00:00 (OUI 00-00-00) Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00) TX power: 127 dbm (0x7f) Primary PHY: LE 1M (0x01) Secondary max skip: 0x00 Secondary PHY: LE 1M (0x01) SID: 0x00 Scan request notifications: Disabled (0x00) > HCI Event: Command Complete (0x0e) plen 5 LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1 Status: Success (0x00) TX power (selected): 7 dbm (0x07) < HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6 Extended advertising: Enabled (0x01) Number of sets: 1 (0x01) Entry 0 Handle: 0x00 Duration: 0 ms (0x00) Max ext adv events: 0 > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Read no of adv sets during initJaganath Kanakkassery1-0/+7
This patch reads the number of advertising sets in the controller during init and save it in hdev. Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Handle extended ADV PDU typesJaganath Kanakkassery1-0/+8
This patch defines the extended ADV types and handle it in ADV report. Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Set Scan PHYs based on selected PHYs by userJaganath Kanakkassery1-1/+3
Use the PHYs selected in Set Phy Configuration management command while scanning. < HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 13 Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) PHYs: 0x05 Entry 0: LE 1M Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) Entry 1: LE Coded Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6 Extended scan: Enabled (0x01) Filter duplicates: Enabled (0x01) Duration: 0 msec (0x0000) Period: 0.00 sec (0x0000) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Add defines for BREDR pkt_type and LE PHYsJaganath Kanakkassery1-0/+14
This also add macros for checking LMP support for different pkt_types Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Define PHY flags in hdev and set 1M as defaultJaganath Kanakkassery1-0/+4
1M is mandatory to be supported by LE controllers and the same would be set in power on. This patch defines hdev flags for LE PHYs and set 1M to default. Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: Use extended LE Connection if supportedJaganath Kanakkassery1-0/+36
This implements extended LE craete connection and enhanced LE conn complete event if the controller supports. For now it is as good as legacy LE connection and event as no new features in the extended connection is handled. < HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26 Filter policy: White list is not used (0x00) Own address type: Public (0x00) Peer address type: Random (0x01) Peer address: DB:7E:2E:1D:85:E8 (Static) Initiating PHYs: 0x01 Entry 0: LE 1M Scan interval: 60.000 msec (0x0060) Scan window: 60.000 msec (0x0060) Min connection interval: 50.00 msec (0x0028) Max connection interval: 70.00 msec (0x0038) Connection latency: 0 (0x0000) Supervision timeout: 420 msec (0x002a) Min connection length: 0.000 msec (0x0000) Max connection length: 0.000 msec (0x0000) > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 2 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) Status: Success (0x00) Handle: 3585 Role: Master (0x00) Peer address type: Random (0x01) Peer address: DB:7E:2E:1D:85:E8 (Static) Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable) Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable) Connection interval: 67.50 msec (0x0036) Connection latency: 0 (0x0000) Supervision timeout: 420 msec (0x002a) Master clock accuracy: 0x00 @ MGMT Event: Device Connected (0x000b) plen 40 LE Address: DB:7E:2E:1D:85:E8 (Static) Flags: 0x00000000 Data length: 27 Name (complete): Designer Mouse Appearance: Mouse (0x03c2) Flags: 0x05 LE Limited Discoverable Mode BR/EDR Not Supported 16-bit Service UUIDs (complete): 1 entry Human Interface Device (0x1812) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: Process extended ADV report eventJaganath Kanakkassery1-0/+26
This patch enables Extended ADV report event if extended scanning is supported in the controller and process the same. The new features are not handled and for now its as good as legacy ADV report. > HCI Event: LE Meta Event (0x3e) plen 53 LE Extended Advertising Report (0x0d) Num reports: 1 Entry 0 Event type: 0x0013 Props: 0x0013 Connectable Scannable Use legacy advertising PDUs Data status: Complete Legacy PDU Type: ADV_IND (0x0013) Address type: Random (0x01) Address: DB:7E:2E:1A:85:E8 (Static) Primary PHY: LE 1M Secondary PHY: LE 1M SID: 0x00 TX power: 0 dBm RSSI: -90 dBm (0xa6) Periodic advertising invteral: 0.00 msec (0x0000) Direct address type: Public (0x00) Direct address: 00:00:00:00:00:00 (OUI 00-00-00) Data length: 0x1b 0f 09 44 65 73 69 67 6e 65 72 20 4d 6f 75 73 65 ..Designer Mouse 03 19 c2 03 02 01 05 03 03 12 18 ........... Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: Use extended scanning if controller supportsJaganath Kanakkassery1-0/+24
This implements Set extended scan param and set extended scan enable commands and use it for start LE scan based on controller support. The new features added in these commands are setting of new PHY for scanning and setting of scan duration. Both features are disabled for now, meaning only 1M PHY is set and scan duration is set to 0 which means that scanning will be done untill scan disable is called. < HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8 Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) PHYs: 0x01 Entry 0: LE 1M Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6 Extended scan: Enabled (0x01) Filter duplicates: Enabled (0x01) Duration: 0 msec (0x0000) Period: 0.00 sec (0x0000) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: Add HCI command for clear Resolv listAnkit Navik1-0/+2
Check for Resolv list supported by controller. So check the supported commmand first before issuing this command i.e.,HCI_OP_LE_CLEAR_RESOLV_LIST Before patch: < HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 13.338168 > HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 13.338842 LE Read White List Size (0x08|0x000f) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 13.339029 > HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 13.339939 LE Clear White List (0x08|0x0010) ncmd 1 Status: Success (0x00) < HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 13.340152 > HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 13.340952 LE Read Resolving List Size (0x08|0x002a) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #61 [hci0] 13.341180 > HCI Event: Command Complete (0x0e) plen 12 #62 [hci0] 13.341898 LE Read Maximum Data Length (0x08|0x002f) ncmd 1 Status: Success (0x00) Max TX octets: 251 Max TX time: 17040 Max RX octets: 251 Max RX time: 17040 After patch: < HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 28.919131 > HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 28.920016 LE Read White List Size (0x08|0x000f) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 28.920164 > HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 28.920873 LE Clear White List (0x08|0x0010) ncmd 1 Status: Success (0x00) < HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 28.921109 > HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 28.922016 LE Read Resolving List Size (0x08|0x002a) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Clear Resolving... (0x08|0x0029) plen 0 #61 [hci0] 28.922166 > HCI Event: Command Complete (0x0e) plen 4 #62 [hci0] 28.922872 LE Clear Resolving List (0x08|0x0029) ncmd 1 Status: Success (0x00) < HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #63 [hci0] 28.923117 > HCI Event: Command Complete (0x0e) plen 12 #64 [hci0] 28.924030 LE Read Maximum Data Length (0x08|0x002f) ncmd 1 Status: Success (0x00) Max TX octets: 251 Max TX time: 17040 Max RX octets: 251 Max RX time: 17040 Signed-off-by: Ankit Navik <ankit.p.navik@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: Store Resolv list sizeAnkit Navik1-0/+6
When the controller supports the Read LE Resolv List size feature, the maximum list size are read and now stored. Before patch: < HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 17.979791 > HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 17.980629 LE Read White List Size (0x08|0x000f) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 17.980786 > HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 17.981627 LE Clear White List (0x08|0x0010) ncmd 1 Status: Success (0x00) < HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #59 [hci0] 17.981786 > HCI Event: Command Complete (0x0e) plen 12 #60 [hci0] 17.982636 LE Read Maximum Data Length (0x08|0x002f) ncmd 1 Status: Success (0x00) Max TX octets: 251 Max TX time: 17040 Max RX octets: 251 Max RX time: 17040 After patch: < HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 13.338168 > HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 13.338842 LE Read White List Size (0x08|0x000f) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 13.339029 > HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 13.339939 LE Clear White List (0x08|0x0010) ncmd 1 Status: Success (0x00) < HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 13.340152 > HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 13.340952 LE Read Resolving List Size (0x08|0x002a) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #61 [hci0] 13.341180 > HCI Event: Command Complete (0x0e) plen 12 #62 [hci0] 13.341898 LE Read Maximum Data Length (0x08|0x002f) ncmd 1 Status: Success (0x00) Max TX octets: 251 Max TX time: 17040 Max RX octets: 251 Max RX time: 17040 Signed-off-by: Ankit Navik <ankit.p.navik@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-10-29Bluetooth: increase timeout for le auto connectionsKonrad Zapałowicz1-1/+1
This patch increases the connection timeout for LE connections that are triggered by the advertising report to 4 seconds. It has been observed that devices equipped with wifi+bt combo SoC fail to create a connection with BLE devices due to their coexistence issues. Increasing this timeout gives them enough time to complete the connection with success. Signed-off-by: Konrad Zapałowicz <konrad.zapalowicz@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-05-18Bluetooth: Set LE Default PHY preferencesMarcel Holtmann1-0/+7
If the LE Set Default PHY command is supported, the indicate to the controller that the host has no preferences for transmitter PHY or receiver PHY selection. Issuing this command gives the controller a clear indication that other PHY can be selected if available. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-05-18Bluetooth: Enable LE Channel Selection Algorithm eventMarcel Holtmann1-0/+1
If the Channel Selection Algorithm #2 feature is supported, then enable the new LE Channel Selection Algorithm event. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2016-09-19Bluetooth: Add framework for Extended Controller InformationMarcel Holtmann1-0/+1
This command is used to retrieve the current state and basic information of a controller. It is typically used right after getting the response to the Read Controller Index List command or an Index Added event (or its extended counterparts). When any of the values in the EIR_Data field changes, the event Extended Controller Information Changed will be used to inform clients about the updated information. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
2016-09-19Bluetooth: Use individual flags for certain management eventsMarcel Holtmann1-1/+4
Instead of hiding everything behind a general managment events flag, introduce indivdual flags that allow fine control over which events are send to a given management channel. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2016-09-19Bluetooth: Add HCI device identifier for Qualcomm SMDBjorn Andersson1-0/+1
This patch assigns the next free HCI device identifier to Bluetooth devices based on the Qualcomm Shared Memory channels. Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-07-13Bluetooth: Add Authentication Failed reason to Disconnected Mgmt eventSzymon Janc1-0/+1
If link is disconnected due to Authentication Failure (PIN or Key Missing status) userspace will be notified about this with proper error code. Many LE profiles define "PIN or Key Missing" status as indication of remote lost bond so this allows userspace to take action on this. @ Device Connected: 88:63:DF:88:0E:83 (1) flags 0x0000 02 01 1a 05 03 0a 18 0d 18 0b 09 48 65 61 72 74 ...........Heart 20 52 61 74 65 Rate > HCI Event: Command Status (0x0f) plen 4 LE Read Remote Used Features (0x08|0x0016) ncmd 1 Status: Success (0x00) > ACL Data RX: Handle 3585 flags 0x02 dlen 11 ATT: Read By Group Type Request (0x10) len 6 Handle range: 0x0001-0xffff Attribute group type: Primary Service (0x2800) > HCI Event: LE Meta Event (0x3e) plen 12 LE Read Remote Used Features (0x04) Status: Success (0x00) Handle: 3585 Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00 LE Encryption < HCI Command: LE Start Encryption (0x08|0x0019) plen 28 Handle: 3585 Random number: 0x0000000000000000 Encrypted diversifier: 0x0000 Long term key: 26201cd479a0921b6f949f0b1fa8dc82 > HCI Event: Command Status (0x0f) plen 4 LE Start Encryption (0x08|0x0019) ncmd 1 Status: Success (0x00) > HCI Event: Encryption Change (0x08) plen 4 Status: PIN or Key Missing (0x06) Handle: 3585 Encryption: Disabled (0x00) < HCI Command: Disconnect (0x01|0x0006) plen 3 Handle: 3585 Reason: Authentication Failure (0x05) > HCI Event: Command Status (0x0f) plen 4 Disconnect (0x01|0x0006) ncmd 1 Status: Success (0x00) > HCI Event: Disconnect Complete (0x05) plen 4 Status: Success (0x00) Handle: 3585 Reason: Connection Terminated By Local Host (0x16) @ Device Disconnected: 88:63:DF:88:0E:83 (1) reason 4 @ Device Connected: C4:43:8F:A3:4D:83 (0) flags 0x0000 08 09 4e 65 78 75 73 20 35 ..Nexus 5 > HCI Event: Command Status (0x0f) plen 4 Authentication Requested (0x01|0x0011) ncmd 1 Status: Success (0x00) > HCI Event: Link Key Request (0x17) plen 6 Address: C4:43:8F:A3:4D:83 (LG Electronics) < HCI Command: Link Key Request Reply (0x01|0x000b) plen 22 Address: C4:43:8F:A3:4D:83 (LG Electronics) Link key: 080812e4aa97a863d11826f71f65a933 > HCI Event: Command Complete (0x0e) plen 10 Link Key Request Reply (0x01|0x000b) ncmd 1 Status: Success (0x00) Address: C4:43:8F:A3:4D:83 (LG Electronics) > HCI Event: Auth Complete (0x06) plen 3 Status: PIN or Key Missing (0x06) Handle: 75 @ Authentication Failed: C4:43:8F:A3:4D:83 (0) status 0x05 < HCI Command: Disconnect (0x01|0x0006) plen 3 Handle: 75 Reason: Remote User Terminated Connection (0x13) > HCI Event: Command Status (0x0f) plen 4 Disconnect (0x01|0x0006) ncmd 1 Status: Success (0x00) > HCI Event: Disconnect Complete (0x05) plen 4 Status: Success (0x00) Handle: 75 Reason: Connection Terminated By Local Host (0x16) @ Device Disconnected: C4:43:8F:A3:4D:83 (0) reason 4 Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2016-07-09Bluetooth: Rename HCI_BREDR into HCI_PRIMARYMarcel Holtmann1-1/+1
The HCI_BREDR naming is confusing since it actually stands for Primary Bluetooth Controller. Which is a term that has been used in the latest standard. However from a legacy point of view there only really have been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of Bluetooth introduced Low Energy (LE) and made this terminology a little bit confused since Dual Mode Controllers include BR/EDR and LE. To simplify this the name HCI_PRIMARY stands for the Primary Controller which can be a single mode or dual mode controller. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2016-04-22Bluetooth: Add defines for SPI and I2CJohan Hedberg1-0/+2
Extend the set of possible HCI bus types with SPI and I2C. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-03-10Bluetooth: Add support for limited privacy modeJohan Hedberg1-0/+1
Introduce a limited privacy mode indicated by value 0x02 to the mgmt Set Privacy command. With value 0x02 the kernel will use privacy mode with a resolvable private address. In case the controller is bondable and discoverable the identity address will be used. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Remove unnecessary HCI_ADVERTISING_INSTANCE flagJohan Hedberg1-1/+0
This flag just tells us whether hdev->adv_instances is empty or not. We can equally well use the list_empty() function to get this information. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-11-19Bluetooth: Add HCI status return parameter to hci_req_sync()Johan Hedberg1-1/+2
In some cases it may be important to get the exact HCI status rather than the converted HCI-to-errno value. Add an optional return parameter to the hci_req_sync() API to allow for this. Since there are no good HCI translation candidates for cancelation and timeout, use the "unknown" status code for those cases. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-21Bluetooth: Add support setup stage internal notification eventMarcel Holtmann1-0/+1
Before the vendor specific setup stage is triggered call back into the core to trigger an internal notification event. That event is used to send an index update to the monitor interface. With that specific event it is possible to update userspace with manufacturer information before any HCI command has been executed. This is useful for early stage debugging of vendor specific initialization sequences. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: Add new quirk for non-persistent diagnostic settingsMarcel Holtmann1-0/+9
If the diagnostic settings are not persistent over HCI Reset, then this quirk can be used to tell the Bluetoth core about it. This will ensure that the settings are programmed correctly when the controller is powered up. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08Bluetooth: Add debugfs entry for setting vendor diagnostic modeMarcel Holtmann1-0/+1
This adds a new debugfs entry for enabling and disabling the vendor diagnostic mode. It is only exposed for drivers that provide the set_diag driver callback and actually have an option for vendor specific diagnostic information. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08Bluetooth: Add support for vendor specific diagnostic channelMarcel Holtmann1-0/+1
Introduce hci_recv_diag function for HCI drivers to allow sending vendor specific diagnostic messages into the Bluetooth core stack. The messages are not processed, but they are forwarded to the monitor channel and can be retrieved by user space diagnostic tools. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-05Bluetooth: Introduce HCI_DEV_OPEN and HCI_DEV_CLOSE eventsMarcel Holtmann1-0/+2
When opening the HCI transport via hdev->open send HCI_DEV_OPEN event and when closing the HCI transport via hdev->close send HCI_DEV_CLOSE. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-06-12Bluetooth: Read encryption key size for BR/EDR connectionsJohan Hedberg1-0/+10
Since Bluetooth 3.0 there's a HCI command available for reading the encryption key size of an BR/EDR connection. This information is essential e.g. for generating an LTK using SMP over BR/EDR, so store it as part of struct hci_conn. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-04-09Bluetooth: Read LE remote features during connection establishmentMarcel Holtmann1-0/+13
When establishing a Bluetooth LE connection, read the remote used features mask to determine which features are supported. This was not really needed with Bluetooth 4.0, but since Bluetooth 4.1 and also 4.2 have introduced new optional features, this becomes more important. This works the same as with BR/EDR where the connection enters the BT_CONFIG stage and hci_connect_cfm call is delayed until the remote features have been retrieved. Only after successfully receiving the remote features, the connection enters the BT_CONNECTED state. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-07Bluetooth: Update SSP OOB data EIR definitionsJohan Hedberg1-2/+4
Since Bluetooth 4.1 there are two additional values for SSP OOB data, namely C-256 and R-256. This patch updates the EIR definitions to take into account both the 192 and 256 bit variants of C and R. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-03-24Bluetooth: Introduce HCI_ADVERTISING_INSTANCE setting and add AD flagsArman Uguray1-0/+2
This patch introduces the HCI_ADVERTISING_INSTANCE setting, which is set when an at least one advertising instance has been added using the "Add Advertising" mgmt command. This patch also adds a macro definition for the EIR_APPEARANCE field type. Signed-off-by: Arman Uguray <armansito@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-03-17Bluetooth: Introduce HCI_QUIRK_SIMULTANEOUS_DISCOVERYJakub Pawlowski1-0/+8
Some controllers allow both LE scan and BR/EDR inquiry to run at the same time, while others allow only one, LE SCAN or BR/EDR inquiry at given time. Since this is specific to each controller, add a new quirk setting that allows drivers to tell the core wether given controller can do both LE scan and BR/EDR inquiry at same time. Signed-off-by: Jakub Pawlowski <jpawlowski@google.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-03-17Bluetooth: Add support for Local OOB Extended Data Update eventsMarcel Holtmann1-0/+1
When a different user requests a new set of local out-of-band data, then inform all previous users that the data has been updated. To limit the scope of users, the updates are limited to previous users. If a user has never requested out-of-band data, it will also not see the update. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-03-16Bluetooth: Add constants for LE SC Confirmation and Random valuesMarcel Holtmann1-0/+2
The LE Secure Connections Confirmation Value and LE Secure Connections Random Value contants are required for the out-of-band data and so just define them. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-03-15Bluetooth: Add defines for LE Bluetooth Device Address and LE RoleMarcel Holtmann1-0/+2
The OOB data requires to include LE Bluetooth Device Address and LE Role and so add the type constants for these fields. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>