aboutsummaryrefslogtreecommitdiffstats
path: root/include/uapi/linux/ethtool.h (follow)
AgeCommit message (Collapse)AuthorFilesLines
2022-10-03ethtool: add interface to interact with Ethernet Power EquipmentOleksij Rempel1-0/+45
Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-23net: phy: Add support for rate matchingSean Anderson1-2/+16
This adds support for rate matching (also known as rate adaptation) to the phy subsystem. The general idea is that the phy interface runs at one speed, and the MAC throttles the rate at which it sends packets to the link speed. There's a good overview of several techniques for achieving this at [1]. This patch adds support for three: pause-frame based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and 2BASE-TL), and open-loop-based (such as in 10GBASE-W). This patch makes a few assumptions and a few non assumptions about the types of rate matching available. First, it assumes that different phys may use different forms of rate matching. Second, it assumes that phys can use rate matching for any of their supported link speeds (e.g. if a phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T). Third, it does not assume that all interface modes will use the same form of rate matching. Fourth, it does not assume that all phy devices will support rate matching (even if some do). Relaxing or strengthening these (non-)assumptions could result in a different API. For example, if all interface modes were assumed to use the same form of rate matching, then a bitmask of interface modes supportting rate matching would suffice. For some better visibility into the process, the current rate matching mode is exposed as part of the ethtool ksettings. For the moment, only read access is supported. I'm not sure what userspace might want to configure yet (disable it altogether, disable just one mode, specify the mode to use, etc.). For the moment, since only pause-based rate adaptation support is added in the next few commits, rate matching can be disabled altogether by adjusting the advertisement. 802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and "rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls this feature "rate adaptation". I chose "rate matching" because it is shorter, and because Russell doesn't think "adaptation" is correct in this context. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-28treewide: uapi: Replace zero-length arrays with flexible-array membersGustavo A. R. Silva1-14/+14
There is a regular need in the kernel to provide a way to declare having a dynamically sized set of trailing elements in a structure. Kernel code should always use “flexible array members”[1] for these cases. The older style of one-element or zero-length arrays should no longer be used[2]. This code was transformed with the help of Coccinelle: (linux-5.19-rc2$ spatch --jobs $(getconf _NPROCESSORS_ONLN) --sp-file script.cocci --include-headers --dir . > output.patch) @@ identifier S, member, array; type T1, T2; @@ struct S { ... T1 member; T2 array[ - 0 ]; }; -fstrict-flex-arrays=3 is coming and we need to land these changes to prevent issues like these in the short future: ../fs/minix/dir.c:337:3: warning: 'strcpy' will always overflow; destination buffer has size 0, but the source string has length 2 (including NUL byte) [-Wfortify-source] strcpy(de3->name, "."); ^ Since these are all [0] to [] changes, the risk to UAPI is nearly zero. If this breaks anything, we can use a union with a new member name. [1] https://en.wikipedia.org/wiki/Flexible_array_member [2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays Link: https://github.com/KSPP/linux/issues/78 Build-tested-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/lkml/62b675ec.wKX6AOZ6cbE71vtF%25lkp@intel.com/ Acked-by: Dan Williams <dan.j.williams@intel.com> # For ndctl.h Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2022-05-01ethtool: Add 10base-T1L link mode entryAlexandru Tachici1-0/+1
Add entry for the 10base-T1L full duplex mode. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-22ethtool: add support to set/get tx copybreak buf size via ethtoolHao Chen1-0/+1
Add support for ethtool to set/get tx copybreak buf size. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-06ethtool: Add transceiver module extended stateIdo Schimmel1-0/+6
Add an extended state and sub-state to describe link issues related to transceiver modules. The 'ETHTOOL_LINK_EXT_SUBSTATE_MODULE_CMIS_NOT_READY' extended sub-state tells user space that port is unable to gain a carrier because the CMIS Module State Machine did not reach the ModuleReady (Fully Operational) state. For example, if the module is stuck at ModuleLowPwr or ModuleFault state. In case of the latter, user space can read the fault reason from the module's EEPROM and potentially reset it. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-06ethtool: Add ability to control transceiver modules' power modeIdo Schimmel1-0/+23
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and 'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver modules parameters and retrieve their status. The first parameter to control is the power mode of the module. It is only relevant for paged memory modules, as flat memory modules always operate in low power mode. When a paged memory module is in low power mode, its power consumption is reduced to the minimum, the management interface towards the host is available and the data path is deactivated. User space can choose to put modules that are not currently in use in low power mode and transition them to high power mode before putting the associated ports administratively up. This is useful for user space that favors reduced power consumption and lower temperatures over reduced link up times. In QSFP-DD modules the transition from low power mode to high power mode can take a few seconds and this transition is only expected to get longer with future / more complex modules. User space can control the power mode of the module via the power mode policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible values: * high: Module is always in high power mode. * auto: Module is transitioned by the host to high power mode when the first port using it is put administratively up and to low power mode when the last port using it is put administratively down. The operational power mode of the module is available to user space via the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not reported to user space when a module is not plugged-in. The user API is designed to be generic enough so that it could be used for modules with different memory maps (e.g., SFF-8636, CMIS). The only implementation of the device driver API in this series is for a MAC driver (mlxsw) where the module is controlled by the device's firmware, but it is designed to be generic enough so that it could also be used by implementations where the module is controlled by the CPU. CMIS testing ============ # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x03 (ModuleReady) LowPwrAllowRequestHW : Off LowPwrRequestSW : Off The module is not in low power mode, as it is not forced by hardware (LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off). The power mode can be queried from the kernel. In case LowPwrAllowRequestHW was on, the kernel would need to take into account the state of the LowPwrRequestHW signal, which is not visible to user space. $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy high power-mode high Change the power mode policy to 'auto': # ethtool --set-module swp11 power-mode-policy auto Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x01 (ModuleLowPwr) LowPwrAllowRequestHW : Off LowPwrRequestSW : On Put the associated port administratively up which will instruct the host to transition the module to high power mode: # ip link set dev swp11 up Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode high Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x03 (ModuleReady) LowPwrAllowRequestHW : Off LowPwrRequestSW : Off Put the associated port administratively down which will instruct the host to transition the module to low power mode: # ip link set dev swp11 down Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x01 (ModuleLowPwr) LowPwrAllowRequestHW : Off LowPwrRequestSW : On SFF-8636 testing ================ # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled Power set : Off Power override : On ... Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm The module is not in low power mode, as it is not forced by hardware (Power override is on) or by software (Power set is off). The power mode can be queried from the kernel. In case Power override was off, the kernel would need to take into account the state of the LPMode signal, which is not visible to user space. $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy high power-mode high Change the power mode policy to 'auto': # ethtool --set-module swp13 power-mode-policy auto Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled Power set : On Power override : On ... Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm Put the associated port administratively up which will instruct the host to transition the module to high power mode: # ip link set dev swp13 up Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode high Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled Power set : Off Power override : On ... Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm Put the associated port administratively down which will instruct the host to transition the module to low power mode: # ip link set dev swp13 down Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled Power set : On Power override : On ... Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-16ethtool: add two link extended substates of bad signal integrityGuangbin Huang1-0/+2
ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_REFERENCE_CLOCK_LOST means the input external clock signal for SerDes is too weak or lost. ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_ALOS means the received signal for SerDes is too weak because analog loss of signal. Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-06-17net: fix mistake path for netdev_features_stringsJian Shen1-2/+2
Th_strings arrays netdev_features_strings, tunable_strings, and phy_tunable_strings has been moved to file net/ethtool/common.c. So fixes the comment. Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-16ethtool: add interface to read RMON statsJakub Kicinski1-0/+2
Most devices maintain RMON (RFC 2819) stats - particularly the "histogram" of packets received by size. Unlike other RFCs which duplicate IEEE stats, the short/oversized frame counters in RMON don't seem to match IEEE stats 1-to-1 either, so expose those, too. Do not expose basic packet, CRC errors etc - those are already otherwise covered. Because standard defines packet ranges only up to 1518, and everything above that should theoretically be "oversized" - devices often create their own ranges. Going beyond what the RFC defines - expose the "histogram" in the Tx direction (assume for now that the ranges will be the same). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-16ethtool: add interface to read standard MAC Ctrl statsJakub Kicinski1-0/+2
Number of devices maintains the standard-based MAC control counters for control frames. Add a API for those. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-16ethtool: add interface to read standard MAC statsJakub Kicinski1-0/+2
Most of the MAC statistics are included in struct rtnl_link_stats64, but some fields are aggregated. Besides it's good to expose these clearly hardware stats separately. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-16ethtool: add a new command for reading standard statsJakub Kicinski1-0/+4
Add an interface for reading standard stats, including stats which don't have a corresponding control interface. Start with IEEE 802.3 PHY stats. There seems to be only one stat to expose there. Define API to not require user space changes when new stats or groups are added. Groups are based on bitset, stats have a string set associated. v1: wrap stats in a nest Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski1-21/+33
Conflicts: MAINTAINERS - keep Chandrasekar drivers/net/ethernet/mellanox/mlx5/core/en_main.c - simple fix + trust the code re-added to param.c in -next is fine include/linux/bpf.h - trivial include/linux/ethtool.h - trivial, fix kdoc while at it include/linux/skmsg.h - move to relevant place in tcp.c, comment re-wrapped net/core/skmsg.c - add the sk = sk // sk = NULL around calls net/tipc/crypto.c - trivial Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-04-07ethtool: fix kdoc in headersJakub Kicinski1-0/+6
Fix remaining issues with kdoc in the ethtool headers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-07ethtool: document reserved fields in the uAPIJakub Kicinski1-1/+21
Add a note on expected handling of reserved fields, and references to all kdocs. This fixes a bunch of kdoc warnings. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-07ethtool: un-kdocify extended link stateJakub Kicinski1-20/+6
Extended link state structures and enums use kdoc headers but then do not describe any of the members. Convert to normal comments. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-26ethtool: document the enum values not definesJakub Kicinski1-10/+10
kdoc does not have good support for documenting defines, and we can't abuse the enum documentation because it generates warnings. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-26ethtool: fec: add note about reuse of reservedJakub Kicinski1-0/+4
struct ethtool_fecparam::reserved can't be used in SET, because ethtool user space doesn't zero-initialize the structure. Make this clear. Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-25ethtool: clarify the ethtool FEC interfaceJakub Kicinski1-7/+30
The definition of the FEC driver interface is quite unclear. Improve the documentation. This is based on current driver and user space code, as well as the discussions about the interface: RFC v1 (24 Oct 2016): https://lore.kernel.org/netdev/1477363849-36517-1-git-send-email-vidya@cumulusnetworks.com/ - this version has the autoneg field - no active_fec field - none vs off confusion is already present RFC v2 (10 Feb 2017): https://lore.kernel.org/netdev/1486727004-11316-1-git-send-email-vidya@cumulusnetworks.com/ - autoneg removed - active_fec added v1 (10 Feb 2017): https://lore.kernel.org/netdev/1486751311-42019-1-git-send-email-vidya@cumulusnetworks.com/ - no changes in the code v1 (24 Jun 2017): https://lore.kernel.org/netdev/1498331985-8525-1-git-send-email-roopa@cumulusnetworks.com/ - include in tree user v2 (27 Jul 2017): https://lore.kernel.org/netdev/1501199248-24695-1-git-send-email-roopa@cumulusnetworks.com/ Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-25ethtool: fec: sanitize ethtool_fecparam->active_fecJakub Kicinski1-1/+1
struct ethtool_fecparam::active_fec is a GET-only field, all in-tree drivers correctly ignore it on SET. Clear the field on SET to avoid any confusion. Again, we can't reject non-zero now since ethtool user space does not zero-init the param correctly. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-25ethtool: fec: sanitize ethtool_fecparam->reservedJakub Kicinski1-1/+1
struct ethtool_fecparam::reserved is never looked at by the core. Make sure it's actually 0. Unfortunately we can't return an error because old ethtool doesn't zero-initialize the structure for SET. On GET we can be more verbose, there are no in tree (ab)users. Fix up the kdoc on the structure. Remove the mention of FEC bypass. Seems like a niche thing to configure in the first place. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-25ethtool: fec: remove long structure descriptionJakub Kicinski1-4/+0
Digging through the mailing list archive @autoneg was part of the first version of the RFC, this left over comment was pointed out twice in review but wasn't removed. The sentence is an exact copy-paste from pauseparam. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-25ethtool: fec: fix typo in kdocJakub Kicinski1-1/+1
s/porte/the port/ Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-12-15uapi: move constants from <linux/kernel.h> to <linux/const.h>Petr Vorel1-1/+1
and include <linux/const.h> in UAPI headers instead of <linux/kernel.h>. The reason is to avoid indirect <linux/sysinfo.h> include when using some network headers: <linux/netlink.h> or others -> <linux/kernel.h> -> <linux/sysinfo.h>. This indirect include causes on MUSL redefinition of struct sysinfo when included both <sys/sysinfo.h> and some of UAPI headers: In file included from x86_64-buildroot-linux-musl/sysroot/usr/include/linux/kernel.h:5, from x86_64-buildroot-linux-musl/sysroot/usr/include/linux/netlink.h:5, from ../include/tst_netlink.h:14, from tst_crypto.c:13: x86_64-buildroot-linux-musl/sysroot/usr/include/linux/sysinfo.h:8:8: error: redefinition of `struct sysinfo' struct sysinfo { ^~~~~~~ In file included from ../include/tst_safe_macros.h:15, from ../include/tst_test.h:93, from tst_crypto.c:11: x86_64-buildroot-linux-musl/sysroot/usr/include/sys/sysinfo.h:10:8: note: originally defined here Link: https://lkml.kernel.org/r/20201015190013.8901-1-petr.vorel@gmail.com Signed-off-by: Petr Vorel <petr.vorel@gmail.com> Suggested-by: Rich Felker <dalias@aerifal.cx> Acked-by: Rich Felker <dalias@libc.org> Cc: Peter Korsgaard <peter@korsgaard.com> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Florian Weimer <fweimer@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-09-19ethtool: Add 100base-FX link mode entriesDan Murphy1-0/+2
Add entries for the 100base-FX full and half duplex supported modes. $ ethtool eth0 Supported ports: [ FIBRE ] Supported link modes: 100baseFX/Half 100baseFX/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: No Supported FEC modes: Not reported Advertised link modes: 100baseFX/Half 100baseFX/Full Advertised pause frame use: No Advertised auto-negotiation: No Advertised FEC modes: Not reported Speed: 100Mb/s Duplex: Full Auto-negotiation: off Port: MII PHYAD: 1 Transceiver: external Supports Wake-on: gs Wake-on: d SecureOn password: 00:00:00:00:00:00 Current message level: 0x00000000 (0) Link detected: yes Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-10ethtool: add tunnel info interfaceJakub Kicinski1-0/+2
Add an interface to report offloaded UDP ports via ethtool netlink. Now that core takes care of tracking which UDP tunnel ports the NICs are aware of we can quite easily export this information out to user space. The responsibility of writing the netlink dumps is split between ethtool code and udp_tunnel_nic.c - since udp_tunnel module may not always be loaded, yet we should always report the capabilities of the NIC. $ ethtool --show-tunnels eth0 Tunnel information for eth0: UDP port table 0: Size: 4 Types: vxlan No entries UDP port table 1: Size: 4 Types: geneve, vxlan-gpe Entries (1): port 1230, vxlan-gpe v4: - back to v2, build fix is now directly in udp_tunnel.h v3: - don't compile ETHTOOL_MSG_TUNNEL_INFO_GET in if CONFIG_INET not set. v2: - fix string set count, - reorder enums in the uAPI, - fix type of ETHTOOL_A_TUNNEL_UDP_TABLE_TYPES to bitset in docs and comments. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-08ethtool: Add support for 100Gbps per lane link modesMeir Lichtinger1-0/+15
Define 100G, 200G and 400G link modes using 100Gbps per lane LR, ER and FR are defined as a single link mode because they are using same technology and by design are fully interoperable. EEPROM content indicates if the module is LR, ER, or FR, and the user space ethtool decoder is planned to support decoding these modes in the EEPROM. Signed-off-by: Meir Lichtinger <meirl@mellanox.com> CC: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-29ethtool: Add link extended stateAmit Cohen1-0/+70
Currently, drivers can only tell whether the link is up/down using LINKSTATE_GET, but no additional information is given. Add attributes to LINKSTATE_GET command in order to allow drivers to expose the user more information in addition to link state to ease the debug process, for example, reason for link down state. Extended state consists of two attributes - link_ext_state and link_ext_substate. The idea is to avoid 'vendor specific' states in order to prevent drivers to use specific link_ext_state that can be in the future common link_ext_state. The substates allows drivers to add more information to the common link_ext_state. For example, vendor can expose 'Autoneg' as link_ext_state and add 'No partner detected during force mode' as link_ext_substate. If a driver cannot pinpoint the extended state with the substate accuracy, it is free to expose only the extended state and omit the substate attribute. Signed-off-by: Amit Cohen <amitc@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-06ethtool: provide UAPI for PHY master/slave configuration.Oleksij Rempel1-1/+15
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of auto-negotiation support, we needed to be able to configure the MASTER-SLAVE role of the port manually or from an application in user space. The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to force MASTER or SLAVE role. See IEEE 802.3-2018: 22.2.4.3.7 MASTER-SLAVE control register (Register 9) 22.2.4.3.8 MASTER-SLAVE status register (Register 10) 40.5.2 MASTER-SLAVE configuration resolution 45.2.1.185.1 MASTER-SLAVE config value (1.2100.14) 45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32) The MASTER-SLAVE role affects the clock configuration: ------------------------------------------------------------------------------- When the PHY is configured as MASTER, the PMA Transmit function shall source TX_TCLK from a local clock source. When configured as SLAVE, the PMA Transmit function shall source TX_TCLK from the clock recovered from data stream provided by MASTER. iMX6Q KSZ9031 XXX ------\ /-----------\ /------------\ | | | | | MAC |<----RGMII----->| PHY Slave |<------>| PHY Master | |<--- 125 MHz ---+-<------/ | | \ | ------/ \-----------/ \------------/ ^ \-TX_TCLK ------------------------------------------------------------------------------- Since some clock or link related issues are only reproducible in a specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial to provide generic (not 100BASE-T1 specific) interface to the user space for configuration flexibility and trouble shooting. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29ethtool: add timestamping related string setsMichal Kubecek1-0/+6
Add three string sets related to timestamping information: ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags ETH_SS_TS_TX_TYPES: timestamping Tx types ETH_SS_TS_RX_FILTERS: timestamping Rx filters These will be used for TIMESTAMP_GET request. v2: avoid compiler warning ("enumeration value not handled in switch") in net_hwtstamp_validate() v3: omit dash in Tx type names ("one-step-*" -> "onestep-*"), suggested by Richard Cochran Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18ethtool: Add support for low latency RS FECAya Levin1-1/+3
Add support for low latency Reed Solomon FEC as LLRS. The LL-FEC is defined by the 25G/50G ethernet consortium, in the document titled "Low Latency Reed Solomon Forward Error Correction" Signed-off-by: Aya Levin <ayal@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> CC: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
2020-01-27ethtool: provide WoL settings with WOL_GET requestMichal Kubecek1-0/+4
Implement WOL_GET request to get wake-on-lan settings for a device, traditionally available via ETHTOOL_GWOL ioctl request. As part of the implementation, provide symbolic names for wake-on-line modes as ETH_SS_WOL_MODES string set. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-27ethtool: provide message mask with DEBUG_GET requestMichal Kubecek1-0/+2
Implement DEBUG_GET request to get debugging settings for a device. At the moment, only message mask corresponding to message level as reported by ETHTOOL_GMSGLVL ioctl request is provided. (It is called message level in ioctl interface but almost all drivers interpret it as a bit mask.) As part of the implementation, provide symbolic names for message mask bits as ETH_SS_MSG_CLASSES string set. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-27ethtool: provide string sets with STRSET_GET requestMichal Kubecek1-0/+3
Requests a contents of one or more string sets, i.e. indexed arrays of strings; this information is provided by ETHTOOL_GSSET_INFO and ETHTOOL_GSTRINGS commands of ioctl interface. Unlike ioctl interface, all information can be retrieved with one request and mulitple string sets can be requested at once. There are three types of requests: - no NLM_F_DUMP, no device: get "global" stringsets - no NLM_F_DUMP, with device: get string sets related to the device - NLM_F_DUMP, no device: get device related string sets for all devices Client can request either all string sets of given type (global or device related) or only specific sets. With ETHTOOL_A_STRSET_COUNTS flag set, only set sizes (numbers of strings) are returned. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-12ethtool: provide link mode names as a string setMichal Kubecek1-0/+2
Unlike e.g. netdev features, the ethtool ioctl interface requires link mode table to be in sync between kernel and userspace for userspace to be able to display and set all link modes supported by kernel. The way arbitrary length bitsets are implemented in netlink interface, this will be no longer needed. To allow userspace to access all link modes running kernel supports, add table of ethernet link mode names and make it available as a string set to userspace GET_STRSET requests. Add build time check to make sure names are defined for all modes declared in enum ethtool_link_mode_bit_indices. Once the string set is available, make it also accessible via ioctl. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-15ethtool: Add support for 400Gbps (50Gbps per lane) link modesJiri Pirko1-0/+6
Add support for 400Gbps speed, link modes of 50Gbps per lane Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-16ethtool: implement Energy Detect Powerdown support via phy-tunableAlexandru Ardelean1-0/+22
The `phy_tunable_id` has been named `ETHTOOL_PHY_EDPD` since it looks like this feature is common across other PHYs (like EEE), and defining `ETHTOOL_PHY_ENERGY_DETECT_POWER_DOWN` seems too long. The way EDPD works, is that the RX block is put to a lower power mode, except for link-pulse detection circuits. The TX block is also put to low power mode, but the PHY wakes-up periodically to send link pulses, to avoid lock-ups in case the other side is also in EDPD mode. Currently, there are 2 PHY drivers that look like they could use this new PHY tunable feature: the `adin` && `micrel` PHYs. The ADIN's datasheet mentions that TX pulses are at intervals of 1 second default each, and they can be disabled. For the Micrel KSZ9031 PHY, the datasheet does not mention whether they can be disabled, but mentions that they can modified. The way this change is structured, is similar to the PHY tunable downshift control: * a `ETHTOOL_PHY_EDPD_DFLT_TX_MSECS` value is exposed to cover a default TX interval; some PHYs could specify a certain value that makes sense * `ETHTOOL_PHY_EDPD_NO_TX` would disable TX when EDPD is enabled * `ETHTOOL_PHY_EDPD_DISABLE` will disable EDPD As noted by the `ETHTOOL_PHY_EDPD_DFLT_TX_MSECS` the interval unit is 1 millisecond, which should cover a reasonable range of intervals: - from 1 millisecond, which does not sound like much of a power-saver - to ~65 seconds which is quite a lot to wait for a link to come up when plugging a cable Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-22net: phy: Add support for 100BaseT1 and 1000BaseT1Andrew Lunn1-0/+2
Add link modes for 100Mbps and 1Gbps over a single pair. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-01ethtool: Add SFF-8436 and SFF-8636 max EEPROM length definitionsErez Alfasi1-0/+3
Added max EEPROM length defines for ethtool usage: #define ETH_MODULE_SFF_8636_MAX_LEN 640 #define ETH_MODULE_SFF_8436_MAX_LEN 640 These definitions are used to determine the EEPROM data length when reading high eeprom pages. For example, SFF-8636 EEPROM data from page 03h needs to be stored at data[512] - data[639]. Signed-off-by: Erez Alfasi <ereza@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-04-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-1/+1
2019-04-08ethtool: avoid signed-unsigned comparison in ethtool_validate_speed()Michael Zhivich1-1/+1
When building C++ userspace code that includes ethtool.h with "-Werror -Wall", g++ complains about signed-unsigned comparison in ethtool_validate_speed() due to definition of SPEED_UNKNOWN as -1. Explicitly cast SPEED_UNKNOWN to __u32 to match type of ethtool_validate_speed() argument. Signed-off-by: Michael Zhivich <mzhivich@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-27ethtool: add PHY Fast Link Down supportHeiner Kallweit1-0/+8
This adds support for Fast Link Down as new PHY tunable. Fast Link Down reduces the time until a link down event is reported for 1000BaseT. According to the standard it's 750ms what is too long for several use cases. v2: - add comment describing the constants Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: phy: improve definition of __ETHTOOL_LINK_MODE_MASK_NBITSHeiner Kallweit1-8/+9
The way to define __ETHTOOL_LINK_MODE_MASK_NBITS seems to be overly complicated, go with a standard approach instead. Whilst we're at it, move the comment to the right place. v2: - rebased Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-19ethtool: Added support for 50Gbps per lane link modesAya Levin1-1/+17
Added support for 50Gbps per lane link modes. Define various 50G, 100G and 200G link modes using it. Signed-off-by: Aya Levin <ayal@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-11-17uapi/ethtool: fix spelling errorsStephen Hemminger1-2/+2
Trivial spelling errors found by codespell. Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-29ethtool: drop get_settings and set_settings callbacksMichal Kubecek1-12/+3
Since [gs]et_settings ethtool_ops callbacks have been deprecated in February 2016, all in tree NIC drivers have been converted to provide [gs]et_link_ksettings() and out of tree drivers have had enough time to do the same. Drop get_settings() and set_settings() and implement both ETHTOOL_[GS]SET and ETHTOOL_[GS]LINKSETTINGS only using [gs]et_link_ksettings(). Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-07ethtool: Add WAKE_FILTER and RX_CLS_FLOW_WAKEFlorian Fainelli1-1/+4
Add the ability to specify through ethtool::rxnfc that a rule location is special and will be used to participate in Wake-on-LAN, by e.g: having a specific pattern be matched. When this is the case, fs->ring_cookie must be set to the special value RX_CLS_FLOW_WAKE. We also define an additional ethtool::wolinfo flag: WAKE_FILTER which can be used to configure an Ethernet adapter to allow Wake-on-LAN using previously programmed filters. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-04ethtool: Remove trailing semicolon for static inlineFlorian Fainelli1-2/+2
Android's header sanitization tool chokes on static inline functions having a trailing semicolon, leading to an incorrectly parsed header file. While the tool should obviously be fixed, also fix the header files for the two affected functions: ethtool_get_flow_spec_ring() and ethtool_get_flow_spec_ring_vf(). Fixes: 8cf6f497de40 ("ethtool: Add helper routines to pass vf to rx_flow_spec") Reporetd-by: Blair Prescott <blair.prescott@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-13net: ethtool: fix spelling mistake: "tubale" -> "tunable"Michael Heimpold1-1/+1
Signed-off-by: Michael Heimpold <mhei@heimpold.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.