| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Except for Kconfig.HZ. That needs a separate treatment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
On architectures with sizeof(int) < sizeof (long), the
computation of mask inside apply_slack() can be undefined if the
computed bit is > 32.
E.g. with: expires = 0xffffe6f5 and slack = 25, we get:
expires_limit = 0x20000000e
bit = 33
mask = (1 << 33) - 1 /* undefined */
On x86, mask becomes 1 and and the slack is not applied properly.
On s390, mask is -1, expires is set to 0 and the timer fires immediately.
Use 1UL << bit to solve that issue.
Suggested-by: Deborah Townsend <dstownse@us.ibm.com>
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20140418152310.GA13654@midget.suse.cz
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Pull timer changes from Thomas Gleixner:
"This assorted collection provides:
- A new timer based timer broadcast feature for systems which do not
provide a global accessible timer device. That allows those
systems to put CPUs into deep idle states where the per cpu timer
device stops.
- A few NOHZ_FULL related improvements to the timer wheel
- The usual updates to timer devices found in ARM SoCs
- Small improvements and updates all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
tick: Remove code duplication in tick_handle_periodic()
tick: Fix spelling mistake in tick_handle_periodic()
x86: hpet: Use proper destructor for delayed work
workqueue: Provide destroy_delayed_work_on_stack()
clocksource: CMT, MTU2, TMU and STI should depend on GENERIC_CLOCKEVENTS
timer: Remove code redundancy while calling get_nohz_timer_target()
hrtimer: Rearrange comments in the order struct members are declared
timer: Use variable head instead of &work_list in __run_timers()
clocksource: exynos_mct: silence a static checker warning
arm: zynq: Add support for cpufreq
arm: zynq: Don't use arm_global_timer with cpufreq
clocksource/cadence_ttc: Overhaul clocksource frequency adjustment
clocksource/cadence_ttc: Call clockevents_update_freq() with IRQs enabled
clocksource: Add Kconfig entries for CMT, MTU2, TMU and STI
sh: Remove Kconfig entries for TMU, CMT and MTU2
ARM: shmobile: Remove CMT, TMU and STI Kconfig entries
clocksource: armada-370-xp: Use atomic access for shared registers
clocksource: orion: Use atomic access for shared registers
clocksource: timer-keystone: Delete unnecessary variable
clocksource: timer-keystone: introduce clocksource driver for Keystone
...
|
|
There are only two users of get_nohz_timer_target(): timer and hrtimer. Both
call it under same circumstances, i.e.
#ifdef CONFIG_NO_HZ_COMMON
if (!pinned && get_sysctl_timer_migration() && idle_cpu(this_cpu))
return get_nohz_timer_target();
#endif
So, it makes more sense to get all this as part of get_nohz_timer_target()
instead of duplicating code at two places. For this another parameter is
required to be passed to this routine, pinned.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: fweisbec@gmail.com
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/1e1b53537217d58d48c2d7a222a9c3ac47d5b64c.1395140107.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We already have a variable 'head' that points to '&work_list', and so
we should use that instead wherever possible.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/r/0d8645a6efc8360c4196c9797d59343abbfdcc5e.1395129136.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Currently we are using two lowest bit of base for internal purpose and
so they both should be zero in the allocated address. The code was
doing the right thing before this patch came in: commit c5f66e99b
(timer: Implement TIMER_IRQSAFE)
Tejun probably forgot to update this piece of code which checks if the
lowest 'n' bits are zero or not and so wasn't updated according to the
new flag. Lets use TIMER_FLAG_MASK in the calculations here.
[ tglx: Massaged changelog ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: fweisbec@gmail.com
Cc: tj@kernel.org
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/9144e10d7e854a0aa8a673332adec356d81a923c.1393576981.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
timer_cpu_notify() should return NOTIFY_OK and nothing else. Anything else would
trigger a BUG_ON(). Return value of this routine is already checked correctly
but is done after issuing a call to init_timer_stats(). The right order would be
to check the error case first and then call init_timer_stats(). Lets do it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: fweisbec@gmail.com
Cc: tj@kernel.org
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/c439f5b6bbc2047e1662f4d523350531425bcf9d.1393576981.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The internal_add_timer() function updates base->next_timer only if
timer->expires < base->next_timer. This is correct, but it also makes
sense to do the same if we add the first non-deferrable timer.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Mike Galbraith <bitbucket@online.de>
|
|
The __run_timers() function currently steps through the list one jiffy at
a time in order to update the timer wheel. However, if the timer wheel
is empty, no adjustment is needed other than updating ->timer_jiffies.
Therefore, just before we add a timer to an empty timer wheel, we should
mark the timer wheel as being up to date. This marking will reduce (and
perhaps eliminate) the jiffy-stepping that a future __run_timers() call
will need to do in response to some future timer posting or migration.
This commit therefore updates ->timer_jiffies for this case.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Mike Galbraith <bitbucket@online.de>
|
|
The __run_timers() function currently steps through the list one jiffy at
a time in order to update the timer wheel. However, if the timer wheel
is empty, no adjustment is needed other than updating ->timer_jiffies.
Therefore, if we just emptied the timer wheel, for example, by deleting
the last timer, we should mark the timer wheel as being up to date.
This marking will reduce (and perhaps eliminate) the jiffy-stepping that
a future __run_timers() call will need to do in response to some future
timer posting or migration. This commit therefore catches ->timer_jiffies
for this case.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Mike Galbraith <bitbucket@online.de>
|
|
The __run_timers() function currently steps through the list one jiffy at
a time in order to update the timer wheel. However, if the timer wheel
is empty, no adjustment is needed other than updating ->timer_jiffies.
In this case, which is likely to be common for NO_HZ_FULL kernels, the
kernel currently incurs a large latency for no good reason. This commit
therefore short-circuits this case.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Mike Galbraith <bitbucket@online.de>
|
|
Currently, the tvec_base structure's ->active_timers field tracks only
the non-deferrable timers, which means that even if ->active_timers is
zero, there might well be deferrable timers in the list. This commit
therefore adds an ->all_timers field to track all the timers, whether
deferrable or not.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Mike Galbraith <bitbucket@online.de>
|
|
When a timer is enqueued or modified on a remote target, the latter is
expected to see and handle this timer on its next tick. However if the
target is idle and CONFIG_NO_HZ_IDLE=y, the CPU may be sleeping tickless
and the timer may be ignored.
wake_up_nohz_cpu() takes care of that by setting TIF_NEED_RESCHED and
sending an IPI to idle targets so that the tick is reevaluated on the
idle loop through the tick_nohz_idle_*() APIs.
Now this is all performed regardless of the power properties of the
timer. If the timer is deferrable, idle targets don't need to be woken
up. Only the next buzy tick needs to care about it, and no IPI kick
is needed for that to happen.
So lets spare the IPI on idle targets when the timer is deferrable.
Meanwhile we keep the current behaviour on full dynticks targets. We can
spare IPIs on idle full dynticks targets as well but some tricky races
against idle_cpu() must be dealt all along to make sure that the timer
is well handled after idle exit. We can deal with that later since
NO_HZ_FULL already has more important powersaving issues.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/CAKohpomMZ0TAN2e6N76_g4ZRzxd5vZ1XfuZfxrP7GMxfTNiLVw@mail.gmail.com
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
|
Jiffies is referenced by the linker script, so it has to be visible.
Handled both the generic and the x86 version.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1391845930-28580-3-git-send-email-ak@linux.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Use the helper function instead of __GFP_ZERO.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Replace the single preempt_count() 'function' that's an lvalue with
two proper functions:
preempt_count() - returns the preempt_count value as rvalue
preempt_count_set() - Allows setting the preempt-count value
Also provide preempt_count_ptr() as a convenience wrapper to implement
all modifying operations.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-orxrbycjozopqfhb4dxdkdvb@git.kernel.org
[ Fixed build failure. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the uses of the __cpuinit macros from C files in
the core kernel directories (kernel, init, lib, mm, and include)
that don't really have a specific maintainer.
[1] https://lkml.org/lkml/2013/5/20/589
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Direct compare of jiffies related values does not work in the wrap
around case. Replace it with time_is_after_jiffies().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/519BC066.5080600@acm.org
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Pull timer fixes from Thomas Gleixner:
- Cure for not using zalloc in the first place, which leads to random
crashes with CPUMASK_OFF_STACK.
- Revert a user space visible change which broke udev
- Add a missing cpu_online early return introduced by the new full
dyntick conversions
- Plug a long standing race in the timer wheel cpu hotplug code.
Sigh...
- Cleanup NOHZ per cpu data on cpu down to prevent stale data on cpu
up.
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Revert ALWAYS_USE_PERSISTENT_CLOCK compile time optimizaitons
timer: Don't reinitialize the cpu base lock during CPU_UP_PREPARE
tick: Don't invoke tick_nohz_stop_sched_tick() if the cpu is offline
tick: Cleanup NOHZ per cpu data on cpu down
tick: Use zalloc_cpumask_var for allocating offstack cpumasks
|
|
An inactive timer's base can refer to a offline cpu's base.
In the current code, cpu_base's lock is blindly reinitialized each
time a CPU is brought up. If a CPU is brought online during the period
that another thread is trying to modify an inactive timer on that CPU
with holding its timer base lock, then the lock will be reinitialized
under its feet. This leads to following SPIN_BUG().
<0> BUG: spinlock already unlocked on CPU#3, kworker/u:3/1466
<0> lock: 0xe3ebe000, .magic: dead4ead, .owner: kworker/u:3/1466, .owner_cpu: 1
<4> [<c0013dc4>] (unwind_backtrace+0x0/0x11c) from [<c026e794>] (do_raw_spin_unlock+0x40/0xcc)
<4> [<c026e794>] (do_raw_spin_unlock+0x40/0xcc) from [<c076c160>] (_raw_spin_unlock+0x8/0x30)
<4> [<c076c160>] (_raw_spin_unlock+0x8/0x30) from [<c009b858>] (mod_timer+0x294/0x310)
<4> [<c009b858>] (mod_timer+0x294/0x310) from [<c00a5e04>] (queue_delayed_work_on+0x104/0x120)
<4> [<c00a5e04>] (queue_delayed_work_on+0x104/0x120) from [<c04eae00>] (sdhci_msm_bus_voting+0x88/0x9c)
<4> [<c04eae00>] (sdhci_msm_bus_voting+0x88/0x9c) from [<c04d8780>] (sdhci_disable+0x40/0x48)
<4> [<c04d8780>] (sdhci_disable+0x40/0x48) from [<c04bf300>] (mmc_release_host+0x4c/0xb0)
<4> [<c04bf300>] (mmc_release_host+0x4c/0xb0) from [<c04c7aac>] (mmc_sd_detect+0x90/0xfc)
<4> [<c04c7aac>] (mmc_sd_detect+0x90/0xfc) from [<c04c2504>] (mmc_rescan+0x7c/0x2c4)
<4> [<c04c2504>] (mmc_rescan+0x7c/0x2c4) from [<c00a6a7c>] (process_one_work+0x27c/0x484)
<4> [<c00a6a7c>] (process_one_work+0x27c/0x484) from [<c00a6e94>] (worker_thread+0x210/0x3b0)
<4> [<c00a6e94>] (worker_thread+0x210/0x3b0) from [<c00aad9c>] (kthread+0x80/0x8c)
<4> [<c00aad9c>] (kthread+0x80/0x8c) from [<c000ea80>] (kernel_thread_exit+0x0/0x8)
As an example, this particular crash occurred when CPU #3 is executing
mod_timer() on an inactive timer whose base is refered to offlined CPU
#2. The code locked the timer_base corresponding to CPU #2. Before it
could proceed, CPU #2 came online and reinitialized the spinlock
corresponding to its base. Thus now CPU #3 held a lock which was
reinitialized. When CPU #3 finally ended up unlocking the old cpu_base
corresponding to CPU #2, we hit the above SPIN_BUG().
CPU #0 CPU #3 CPU #2
------ ------- -------
..... ...... <Offline>
mod_timer()
lock_timer_base
spin_lock_irqsave(&base->lock)
cpu_up(2) ..... ......
init_timers_cpu()
.... ..... spin_lock_init(&base->lock)
..... spin_unlock_irqrestore(&base->lock) ......
<spin_bug>
Allocation of per_cpu timer vector bases is done only once under
"tvec_base_done[]" check. In the current code, spinlock_initialization
of base->lock isn't under this check. When a CPU is up each time the
base lock is reinitialized. Move base spinlock initialization under
the check.
Signed-off-by: Tirupathi Reddy <tirupath@codeaurora.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1368520142-4136-1-git-send-email-tirupath@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Pull 'full dynticks' support from Ingo Molnar:
"This tree from Frederic Weisbecker adds a new, (exciting! :-) core
kernel feature to the timer and scheduler subsystems: 'full dynticks',
or CONFIG_NO_HZ_FULL=y.
This feature extends the nohz variable-size timer tick feature from
idle to busy CPUs (running at most one task) as well, potentially
reducing the number of timer interrupts significantly.
This feature got motivated by real-time folks and the -rt tree, but
the general utility and motivation of full-dynticks runs wider than
that:
- HPC workloads get faster: CPUs running a single task should be able
to utilize a maximum amount of CPU power. A periodic timer tick at
HZ=1000 can cause a constant overhead of up to 1.0%. This feature
removes that overhead - and speeds up the system by 0.5%-1.0% on
typical distro configs even on modern systems.
- Real-time workload latency reduction: CPUs running critical tasks
should experience as little jitter as possible. The last remaining
source of kernel-related jitter was the periodic timer tick.
- A single task executing on a CPU is a pretty common situation,
especially with an increasing number of cores/CPUs, so this feature
helps desktop and mobile workloads as well.
The cost of the feature is mainly related to increased timer
reprogramming overhead when a CPU switches its tick period, and thus
slightly longer to-idle and from-idle latency.
Configuration-wise a third mode of operation is added to the existing
two NOHZ kconfig modes:
- CONFIG_HZ_PERIODIC: [formerly !CONFIG_NO_HZ], now explicitly named
as a config option. This is the traditional Linux periodic tick
design: there's a HZ tick going on all the time, regardless of
whether a CPU is idle or not.
- CONFIG_NO_HZ_IDLE: [formerly CONFIG_NO_HZ=y], this turns off the
periodic tick when a CPU enters idle mode.
- CONFIG_NO_HZ_FULL: this new mode, in addition to turning off the
tick when a CPU is idle, also slows the tick down to 1 Hz (one
timer interrupt per second) when only a single task is running on a
CPU.
The .config behavior is compatible: existing !CONFIG_NO_HZ and
CONFIG_NO_HZ=y settings get translated to the new values, without the
user having to configure anything. CONFIG_NO_HZ_FULL is turned off by
default.
This feature is based on a lot of infrastructure work that has been
steadily going upstream in the last 2-3 cycles: related RCU support
and non-periodic cputime support in particular is upstream already.
This tree adds the final pieces and activates the feature. The pull
request is marked RFC because:
- it's marked 64-bit only at the moment - the 32-bit support patch is
small but did not get ready in time.
- it has a number of fresh commits that came in after the merge
window. The overwhelming majority of commits are from before the
merge window, but still some aspects of the tree are fresh and so I
marked it RFC.
- it's a pretty wide-reaching feature with lots of effects - and
while the components have been in testing for some time, the full
combination is still not very widely used. That it's default-off
should reduce its regression abilities and obviously there are no
known regressions with CONFIG_NO_HZ_FULL=y enabled either.
- the feature is not completely idempotent: there is no 100%
equivalent replacement for a periodic scheduler/timer tick. In
particular there's ongoing work to map out and reduce its effects
on scheduler load-balancing and statistics. This should not impact
correctness though, there are no known regressions related to this
feature at this point.
- it's a pretty ambitious feature that with time will likely be
enabled by most Linux distros, and we'd like you to make input on
its design/implementation, if you dislike some aspect we missed.
Without flaming us to crisp! :-)
Future plans:
- there's ongoing work to reduce 1Hz to 0Hz, to essentially shut off
the periodic tick altogether when there's a single busy task on a
CPU. We'd first like 1 Hz to be exposed more widely before we go
for the 0 Hz target though.
- once we reach 0 Hz we can remove the periodic tick assumption from
nr_running>=2 as well, by essentially interrupting busy tasks only
as frequently as the sched_latency constraints require us to do -
once every 4-40 msecs, depending on nr_running.
I am personally leaning towards biting the bullet and doing this in
v3.10, like the -rt tree this effort has been going on for too long -
but the final word is up to you as usual.
More technical details can be found in Documentation/timers/NO_HZ.txt"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
sched: Keep at least 1 tick per second for active dynticks tasks
rcu: Fix full dynticks' dependency on wide RCU nocb mode
nohz: Protect smp_processor_id() in tick_nohz_task_switch()
nohz_full: Add documentation.
cputime_nsecs: use math64.h for nsec resolution conversion helpers
nohz: Select VIRT_CPU_ACCOUNTING_GEN from full dynticks config
nohz: Reduce overhead under high-freq idling patterns
nohz: Remove full dynticks' superfluous dependency on RCU tree
nohz: Fix unavailable tick_stop tracepoint in dynticks idle
nohz: Add basic tracing
nohz: Select wide RCU nocb for full dynticks
nohz: Disable the tick when irq resume in full dynticks CPU
nohz: Re-evaluate the tick for the new task after a context switch
nohz: Prepare to stop the tick on irq exit
nohz: Implement full dynticks kick
nohz: Re-evaluate the tick from the scheduler IPI
sched: New helper to prevent from stopping the tick in full dynticks
sched: Kick full dynticks CPU that have more than one task enqueued.
perf: New helper to prevent full dynticks CPUs from stopping tick
perf: Kick full dynticks CPU if events rotation is needed
...
|
|
Andrew Morton noted:
akpm3:/usr/src/25> grep SYSCALL kernel/timer.c
SYSCALL_DEFINE1(alarm, unsigned int, seconds)
SYSCALL_DEFINE0(getpid)
SYSCALL_DEFINE0(getppid)
SYSCALL_DEFINE0(getuid)
SYSCALL_DEFINE0(geteuid)
SYSCALL_DEFINE0(getgid)
SYSCALL_DEFINE0(getegid)
SYSCALL_DEFINE0(gettid)
SYSCALL_DEFINE1(sysinfo, struct sysinfo __user *, info)
COMPAT_SYSCALL_DEFINE1(sysinfo, struct compat_sysinfo __user *, info)
Only one of those should be in kernel/timer.c. Who wrote this thing?
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The only use outside of kernel/timer.c was in kernel/compat.c, so move
compat_sys_sysinfo() next to sys_sysinfo() in kernel/timer.c.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We are planning to convert the dynticks Kconfig options layout
into a choice menu. The user must be able to easily pick
any of the following implementations: constant periodic tick,
idle dynticks, full dynticks.
As this implies a mutual exclusion, the two dynticks implementions
need to converge on the selection of a common Kconfig option in order
to ease the sharing of a common infrastructure.
It would thus seem pretty natural to reuse CONFIG_NO_HZ to
that end. It already implements all the idle dynticks code
and the full dynticks depends on all that code for now.
So ideally the choice menu would propose CONFIG_NO_HZ_IDLE and
CONFIG_NO_HZ_EXTENDED then both would select CONFIG_NO_HZ.
On the other hand we want to stay backward compatible: if
CONFIG_NO_HZ is set in an older config file, we want to
enable CONFIG_NO_HZ_IDLE by default.
But we can't afford both at the same time or we run into
a circular dependency:
1) CONFIG_NO_HZ_IDLE and CONFIG_NO_HZ_EXTENDED both select
CONFIG_NO_HZ
2) If CONFIG_NO_HZ is set, we default to CONFIG_NO_HZ_IDLE
We might be able to support that from Kconfig/Kbuild but it
may not be wise to introduce such a confusing behaviour.
So to solve this, create a new CONFIG_NO_HZ_COMMON option
which gathers the common code between idle and full dynticks
(that common code for now is simply the idle dynticks code)
and select it from their referring Kconfig.
Then we'll later create CONFIG_NO_HZ_IDLE and map CONFIG_NO_HZ
to it for backward compatibility.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
Wake up a CPU when a timer list timer is enqueued there and
the target is part of the full dynticks range. Sending an IPI
to it makes it reconsidering the next timer to program on top
of recent updates.
This may later be improved by checking if the tick is really
stopped on the target. This would need some careful
synchronization though. So deal with such optimization later
and start simple.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
Pull scheduler changes from Ingo Molnar:
"Main changes:
- scheduler side full-dynticks (user-space execution is undisturbed
and receives no timer IRQs) preparation changes that convert the
cputime accounting code to be full-dynticks ready, from Frederic
Weisbecker.
- Initial sched.h split-up changes, by Clark Williams
- select_idle_sibling() performance improvement by Mike Galbraith:
" 1 tbench pair (worst case) in a 10 core + SMT package:
pre 15.22 MB/sec 1 procs
post 252.01 MB/sec 1 procs "
- sched_rr_get_interval() ABI fix/change. We think this detail is not
used by apps (so it's not an ABI in practice), but lets keep it
under observation.
- misc RT scheduling cleanups, optimizations"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched/rt: Add <linux/sched/rt.h> header to <linux/init_task.h>
cputime: Remove irqsave from seqlock readers
sched, powerpc: Fix sched.h split-up build failure
cputime: Restore CPU_ACCOUNTING config defaults for PPC64
sched/rt: Move rt specific bits into new header file
sched/rt: Add a tuning knob to allow changing SCHED_RR timeslice
sched: Move sched.h sysctl bits into separate header
sched: Fix signedness bug in yield_to()
sched: Fix select_idle_sibling() bouncing cow syndrome
sched/rt: Further simplify pick_rt_task()
sched/rt: Do not account zero delta_exec in update_curr_rt()
cputime: Safely read cputime of full dynticks CPUs
kvm: Prepare to add generic guest entry/exit callbacks
cputime: Use accessors to read task cputime stats
cputime: Allow dynamic switch between tick/virtual based cputime accounting
cputime: Generic on-demand virtual cputime accounting
cputime: Move default nsecs_to_cputime() to jiffies based cputime file
cputime: Librarize per nsecs resolution cputime definitions
cputime: Avoid multiplication overflow on utime scaling
context_tracking: Export context state for generic vtime
...
Fix up conflict in kernel/context_tracking.c due to comment additions.
|
|
Move the sysctl-related bits from include/linux/sched.h into
a new file: include/linux/sched/sysctl.h. Then update source
files requiring access to those bits by including the new
header file.
Signed-off-by: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094659.06dced96@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
klogd is woken up asynchronously from the tick in order
to do it safely.
However if printk is called when the tick is stopped, the reader
won't be woken up until the next interrupt, which might not fire
for a while. As a result, the user may miss some message.
To fix this, lets implement the printk tick using a lazy irq work.
This subsystem takes care of the timer tick state and can
fix up accordingly.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Adding two (or more) timers with large values for "expires" (they have
to reside within tv5 in the same list) leads to endless looping
between cascade() and internal_add_timer() in case CONFIG_BASE_SMALL
is one and jiffies are crossing the value 1 << 18. The bug was
introduced between 2.6.11 and 2.6.12 (and survived for quite some
time).
This patch ensures that when cascade() is called timers within tv5 are
not added endlessly to their own list again, instead they are added to
the next lower tv level tv4 (as expected).
Signed-off-by: Christian Hildner <christian.hildner@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: http://lkml.kernel.org/r/98673C87CB31274881CFFE0B65ECC87B0F5FC1963E@DEFTHW99EA4MSX.ww902.siemens.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
|
|
|
|
Timer internals are protected with irq-safe locks but timer execution
isn't, so a timer being dequeued for execution and its execution
aren't atomic against IRQs. This makes it impossible to wait for its
completion from IRQ handlers and difficult to shoot down a timer from
IRQ handlers.
This issue caused some issues for delayed_work interface. Because
there's no way to reliably shoot down delayed_work->timer from IRQ
handlers, __cancel_delayed_work() can't share the logic to steal the
target delayed_work with cancel_delayed_work_sync(), and can only
steal delayed_works which are on queued on timer. Similarly, the
pending mod_delayed_work() can't be used from IRQ handlers.
This patch adds a new timer flag TIMER_IRQSAFE, which makes the timer
to be executed without enabling IRQ after dequeueing such that its
dequeueing and execution are atomic against IRQ handlers.
This makes it safe to wait for the timer's completion from IRQ
handlers, for example, using del_timer_sync(). It can never be
executing on the local CPU and if executing on other CPUs it won't be
interrupted until done.
This will enable simplifying delayed_work cancel/mod interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: torvalds@linux-foundation.org
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/1344449428-24962-5-git-send-email-tj@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Over time, timer initializers became messy with unnecessarily
duplicated code which are inconsistently spread across timer.h and
timer.c.
This patch cleans up timer initializers.
* timer.c::__init_timer() is renamed to do_init_timer().
* __TIMER_INITIALIZER() added. It takes @flags and all initializers
are wrappers around it.
* init_timer[_on_stack]_key() now take @flags.
* __init_timer[_on_stack]() added. They take @flags and all init
macros are wrappers around them.
* __setup_timer[_on_stack]() added. It uses __init_timer() and takes
@flags. All setup macros are wrappers around the two.
Note that this patch doesn't add missing init/setup combinations -
e.g. init_timer_deferrable_on_stack(). Adding missing ones is
trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: torvalds@linux-foundation.org
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/1344449428-24962-4-git-send-email-tj@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
To prepare for addition of another flag, generalize timer->base flags
handling.
* Rename from TBASE_*_FLAG to TIMER_* and make them LU constants.
* Define and use TIMER_FLAG_MASK for flags masking so that multiple
flags can be handled correctly.
* Don't dereference timer->base directly even if
!tbase_get_deferrable(). All two such places are already passed in
@base, so use it instead.
* Make sure tvec_base's alignment is large enough for timer->base
flags using BUILD_BUG_ON().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: torvalds@linux-foundation.org
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/1344449428-24962-2-git-send-email-tj@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
New helper: current_thread_info(). Allows to do a bunch of odd syscalls
in C. While we are at it, there had never been a reason to do
osf_getpriority() in assembler. We also get "namespace"-aware (read:
consistent with getuid(2), etc.) behaviour from getx?id() syscalls now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Gilad reported at
http://lkml.kernel.org/r/1336056962-10465-2-git-send-email-gilad@benyossef.com
"Current timer code fails to correctly return a value meaning that
there is no future timer event, with the result that the timer keeps
getting re-armed in HZ one shot mode even when we could turn it off,
generating unneeded interrupts.
What is happening is that when __next_timer_interrupt() wishes
to return a value that signifies "there is no future timer
event", it returns (base->timer_jiffies + NEXT_TIMER_MAX_DELTA).
However, the code in tick_nohz_stop_sched_tick(), which called
__next_timer_interrupt() via get_next_timer_interrupt(),
compares the return value to (last_jiffies + NEXT_TIMER_MAX_DELTA)
to see if the timer needs to be re-armed.
base->timer_jiffies != last_jiffies and so tick_nohz_stop_sched_tick()
interperts the return value as indication that there is a distant
future event 12 days from now and programs the timer to fire next
after KTIME_MAX nsecs instead of avoiding to arm it. This ends up
causing a needless interrupt once every KTIME_MAX nsecs."
Fix this by using the new active timer accounting. This avoids scans
when no active timer is enqueued completely, so we don't have to rely
on base->timer_next and base->timer_jiffies anymore.
Reported-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20120525214819.317535385@linutronix.de
|
|
The code in get_next_timer_interrupt() is suboptimal as it has to run
through the cascade to find the next expiring timer. On a completely
idle core we should only do that when there is an active timer
enqueued and base->next_timer does not give us a fast answer.
Add accounting of the active timers to the now consolidated
attach/detach code. I deliberately avoided sanity checks because the
code is fully symetric and any fiddling with timers w/o using the API
functions will lead to cute explosions anyway. ulong is big enough
even on 32bit and if we really run into the situation to have more
than 1<<32 timers enqueued there, then we are definitely not in a
state to go idle and run through that code.
This allows us to fix another shortcoming of get_next_timer_interrupt().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20120525214819.236377028@linutronix.de
|
|
Another bunch of mindlessly copied code. All callers of
internal_add_timer() except the recascading code updates
base->next_timer.
Move this into internal_add_timer() and let the cascading code call
__internal_add_timer().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20120525214819.189946224@linutronix.de
|
|
Most callers of detach_timer() have the same pattern around
them. Check whether the timer is pending and eventually updating
base->next_timer.
Create detach_if_pending() and replace the duplicated code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20120525214819.131246037@linutronix.de
|
|
Pull user namespace enhancements from Eric Biederman:
"This is a course correction for the user namespace, so that we can
reach an inexpensive, maintainable, and reasonably complete
implementation.
Highlights:
- Config guards make it impossible to enable the user namespace and
code that has not been converted to be user namespace safe.
- Use of the new kuid_t type ensures the if you somehow get past the
config guards the kernel will encounter type errors if you enable
user namespaces and attempt to compile in code whose permission
checks have not been updated to be user namespace safe.
- All uids from child user namespaces are mapped into the initial
user namespace before they are processed. Removing the need to add
an additional check to see if the user namespace of the compared
uids remains the same.
- With the user namespaces compiled out the performance is as good or
better than it is today.
- For most operations absolutely nothing changes performance or
operationally with the user namespace enabled.
- The worst case performance I could come up with was timing 1
billion cache cold stat operations with the user namespace code
enabled. This went from 156s to 164s on my laptop (or 156ns to
164ns per stat operation).
- (uid_t)-1 and (gid_t)-1 are reserved as an internal error value.
Most uid/gid setting system calls treat these value specially
anyway so attempting to use -1 as a uid would likely cause
entertaining failures in userspace.
- If setuid is called with a uid that can not be mapped setuid fails.
I have looked at sendmail, login, ssh and every other program I
could think of that would call setuid and they all check for and
handle the case where setuid fails.
- If stat or a similar system call is called from a context in which
we can not map a uid we lie and return overflowuid. The LFS
experience suggests not lying and returning an error code might be
better, but the historical precedent with uids is different and I
can not think of anything that would break by lying about a uid we
can't map.
- Capabilities are localized to the current user namespace making it
safe to give the initial user in a user namespace all capabilities.
My git tree covers all of the modifications needed to convert the core
kernel and enough changes to make a system bootable to runlevel 1."
Fix up trivial conflicts due to nearby independent changes in fs/stat.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
userns: Silence silly gcc warning.
cred: use correct cred accessor with regards to rcu read lock
userns: Convert the move_pages, and migrate_pages permission checks to use uid_eq
userns: Convert cgroup permission checks to use uid_eq
userns: Convert tmpfs to use kuid and kgid where appropriate
userns: Convert sysfs to use kgid/kuid where appropriate
userns: Convert sysctl permission checks to use kuid and kgids.
userns: Convert proc to use kuid/kgid where appropriate
userns: Convert ext4 to user kuid/kgid where appropriate
userns: Convert ext3 to use kuid/kgid where appropriate
userns: Convert ext2 to use kuid/kgid where appropriate.
userns: Convert devpts to use kuid/kgid where appropriate
userns: Convert binary formats to use kuid/kgid where appropriate
userns: Add negative depends on entries to avoid building code that is userns unsafe
userns: signal remove unnecessary map_cred_ns
userns: Teach inode_capable to understand inodes whose uids map to other namespaces.
userns: Fail exec for suid and sgid binaries with ids outside our user namespace.
userns: Convert stat to return values mapped from kuids and kgids
userns: Convert user specfied uids and gids in chown into kuids and kgid
userns: Use uid_eq gid_eq helpers when comparing kuids and kgids in the vfs
...
|
|
Pull workqueue changes from Tejun Heo:
"Nothing exciting. Most are updates to debug stuff and related fixes.
Two not-too-critical bugs are fixed - WARN_ON() triggering spurious
during cpu offlining and unlikely lockdep related oops."
* 'for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
lockdep: fix oops in processing workqueue
workqueue: skip nr_running sanity check in worker_enter_idle() if trustee is active
workqueue: Catch more locking problems with flush_work()
workqueue: change BUG_ON() to WARN_ON()
trace: Remove unused workqueue tracer
|
|
Under memory load, on x86_64, with lockdep enabled, the workqueue's
process_one_work() has been seen to oops in __lock_acquire(), barfing
on a 0xffffffff00000000 pointer in the lockdep_map's class_cache[].
Because it's permissible to free a work_struct from its callout function,
the map used is an onstack copy of the map given in the work_struct: and
that copy is made without any locking.
Surprisingly, gcc (4.5.1 in Hugh's case) uses "rep movsl" rather than
"rep movsq" for that structure copy: which might race with a workqueue
user's wait_on_work() doing lock_map_acquire() on the source of the
copy, putting a pointer into the class_cache[], but only in time for
the top half of that pointer to be copied to the destination map.
Boom when process_one_work() subsequently does lock_map_acquire()
on its onstack copy of the lockdep_map.
Fix this, and a similar instance in call_timer_fn(), with a
lockdep_copy_map() function which additionally NULLs the class_cache[].
Note: this oops was actually seen on 3.4-next, where flush_work() newly
does the racing lock_map_acquire(); but Tejun points out that 3.4 and
earlier are already vulnerable to the same through wait_on_work().
* Patch orginally from Peter. Hugh modified it a bit and wrote the
description.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Reported-by: Hugh Dickins <hughd@google.com>
LKML-Reference: <alpine.LSU.2.00.1205070951170.1544@eggly.anvils>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Convert setregid, setgid, setreuid, setuid,
setresuid, getresuid, setresgid, getresgid, setfsuid, setfsgid,
getuid, geteuid, getgid, getegid,
waitpid, waitid, wait4.
Convert userspace uids and gids into kuids and kgids before
being placed on struct cred. Convert struct cred kuids and
kgids into userspace uids and gids when returning them.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
|
|
The mod_timer_pinned() header comment states that it prevents timers
from being migrated to a different CPU. This is not the case, instead,
it ensures that the timer is posted to the current CPU, but does nothing
to prevent CPU-hotplug operations from migrating the timer.
This commit therefore brings the comment header into alignment with
reality.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
|
|
* 'core-debugobjects-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timer: Use debugobjects to catch deletion of uninitialized timers
timer: Setup uninitialized timer with a stub callback
debugobjects: Extend to assert that an object is initialized
debugobjects: Be smarter about static objects
|
|
In order to safely dereference current->real_parent inside an
rcu_read_lock, we need an rcu_dereference.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
del_timer_sync() calls debug_object_assert_init() to assert that
a timer has been initialized before calling lock_timer_base().
lock_timer_base() would spin forever on a NULL(uninit-ed) base.
The check is added to del_timer() to prevent silent failure, even
though it would not get stuck in an infinite loop.
[ sboyd@codeaurora.org: Remove WARN, intialize timer function]
Signed-off-by: Christine Chan <cschan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/1320724108-20788-4-git-send-email-sboyd@codeaurora.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Remove the WARN_ON() in timer_fixup_activate() as we now get the
debugobjects printout in the debugobjects activate check.
We also assign a dummy timer callback so that if the timer is
actually set to fire we don't oops.
[ tglx@linutronix.de: Split out the debugobjects vs. the timer change ]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Christine Chan <cschan@codeaurora.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1320724108-20788-2-git-send-email-sboyd@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The changed files were only including linux/module.h for the
EXPORT_SYMBOL infrastructure, and nothing else. Revector them
onto the isolated export header for faster compile times.
Nothing to see here but a whole lot of instances of:
-#include <linux/module.h>
+#include <linux/export.h>
This commit is only changing the kernel dir; next targets
will probably be mm, fs, the arch dirs, etc.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
Thomas Gleixner
Jiri Bohac
Linus Torvalds
Viresh Kumar
Oleg Nesterov
Paul E. McKenney
Andi Kleen
Joe Perches
Peter Zijlstra
Paul Gortmaker
Bart Van Assche
Tirupathi Reddy
Stephen Rothwell
Frederic Weisbecker
Clark Williams
Hildner, Christian
Tejun Heo
Al Viro
Eric W. Biederman
Paul E. McKenney
Mandeep Singh Baines
Christine Chan
Stephen Boyd