| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Instead of hard coding the scale target in the test, dynamically set it
based on the maximum number of flow counters and their current
occupancy.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This tests creates as many RIFs as possible, ideally more than there can be
RIF counters (though that is currently only possible on Spectrum-1). It
then tries to enable L3 HW stats on each of the RIFs. It also contains the
traffic test, which tries to run traffic through a log2 of those counters
and checks that the traffic is shown in the counter values.
Like with tc_flower traffic test, take a log2 subset of rules. The logic
behind picking log2 rules is that then every bit of the instantiated item's
number is exercised. This should catch issues whether they happen at the
high end, low end, or somewhere in between.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scale tests are verifying behavior of mlxsw when number of instances of
some resource reaches the ASIC capacity. The number of instances is
referred to as "target" number.
No scale tests so far needed to know this target number to clean up. E.g.
the tc_flower simply removes the clsact qdisc that all the tested filters
are hooked onto, and that takes care of collecting all the filters.
However, for the RIF counter test, which is being added in a future patch,
VLAN netdevices are created. These are created as part of the test, but of
course the cleanup needs to undo them again. For that it needs to know how
many there were. To support this usage, pass the target number to the
cleanup callback.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scale tests are currently testing two things: that some number of
instances of a given resource can actually be created; and that when an
attempt is made to create more than the supported amount, the failures are
noted and handled gracefully.
Sometimes the scale test depends on more than one resource. In particular,
a following patch will add a RIF counter scale test, which depends on the
number of RIF counters that can be bound, and also on the number of RIFs
that can be created.
When the test is limited by the auxiliary resource and not by the primary
one, there's no point trying to run the overflow test, because it would be
testing exhaustion of the wrong resource.
To support this use case, when the $test_get_target yields 0, skip the test
instead.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scale tests are currently testing two things: that some number of
instances of a given resource can actually be created; and that when an
attempt is made to create more than the supported amount, the failures are
noted and handled gracefully.
However the ability to allocate the resource does not mean that the
resource actually works when passing traffic. For that, make it possible
for a given scale to also test traffic.
Traffic test is only run on the positive leg of the scale test (no point
trying to pass traffic when the expected outcome is that the resource will
not be allocated). Traffic tests are opt-in, if a given test does not
expose it, it is not run.
To this end, delay the test cleanup until after the traffic test is run.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scale of each resource is tested in the following manner:
1. The scale target is queried.
2. The test setup is prepared.
3. The test is invoked.
In some cases, the occupancy of a resource changes as part of the second
step, requiring the test to return a scale target that takes this change
into account.
Make this more robust by re-querying the scale target after the second
step.
Another possible solution is to swap the first and second steps, but
when a test needs to be skipped (i.e., scale target is zero), the setup
would have been in vain.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The test verifies that packets are correctly flooded by the bridge and
the VXLAN device by matching on the encapsulated packets at the other
end. However, if packets other than those generated by the test also
ingress the bridge (e.g., MLD packets), they will be flooded as well and
interfere with the expected count.
Make the test more robust by making sure that only the packets generated
by the test can ingress the bridge. Drop all the rest using tc filters
on the egress of 'br0' and 'h1'.
In the software data path, the problem can be solved by matching on the
inner destination MAC or dropping unwanted packets at the egress of the
VXLAN device, but this is not currently supported by mlxsw.
Fixes: d01724dd2a66 ("selftests: mlxsw: spectrum-2: Add a test for VxLAN flooding with IPv6")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.
The number of records is changed according to ASIC type and address
family.
Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-2 and above, which support up to four
IPv6 addresses in one record.
The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Query the maximum number of supported RIF MAC profiles using
devlink-resource and verify that all available MAC profiles can be utilized
and that an error is generated when user space tries to exceed this number.
Output example in Spectrum-2:
$ TESTS='rif_mac_profile' ./resource_scale.sh
TEST: 'rif_mac_profile' 4 [ OK ]
TEST: 'rif_mac_profile' overflow 5 [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of mlxsw-specific selftests currently detect whether they are run
on a compatible machine, and bail out silently when not. These tests are
however done in a somewhat impenetrable manner by directly comparing PCI
IDs against a blacklist or a whitelist, and bailing out silently if the
machine is not compatible.
Instead, add a helper, mlxsw_only_on_spectrum(), which allows specifying
the supported machines in a human-readable manner. If the current machine
is incompatible, the helper emits a SKIP message and returns an error code,
based on which the caller can gracefully bail out in a suitable way. This
allows a more readable conditions such as:
mlxsw_only_on_spectrum 2+ || return
Convert all existing open-coded guards to the new helper. Also add two new
guards to do_mark_test() and do_drop_test(), which are supported only on
Spectrum-2+, but the corresponding check was not there.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 underlay support was added, add test to check that "decap_error" trap
is triggered under the right conditions and that devlink counters increase.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the resource scale test checks a few cases, when the error code
resets between the cases. So for example, if one case fails and the
consecutive case passes, the error code eventually will fit the last test
and will be 0.
Save a new return code that will hold the 'or' return codes of all the
cases, so the final return code will consider all the cases.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
q_in_vni_veto.sh is not needed anymore because VxLAN with an 802.1ad
bridge and VxLAN with an 802.1d bridge can coexist.
Remove the test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Query the maximum number of supported physical ports using devlink-resource
and test that this number can be reached by splitting each of the
splittable ports to its width. Test that an error is returned in case
the maximum number is exceeded.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add tests to ensure that the forbidden and unsupported cases are indeed
vetoed by mlxsw driver.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Query the maximum number of supported policers using devlink-resource
and test that this number can be reached by configuring tc filters with
police action. Test that an error is returned in case the maximum number
is exceeded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With the change that made the code to query counter bank size from device
instead of using hard-coded value, the number of available counters
changed for Spectrum-2. Adjust the limit in the selftests.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scale test for Spectrum-2 should be invoked for Spectrum-2 and
Spectrum-3. Add the appropriate device ID.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scale test for Spectrum-2 should only be invoked for Spectrum-2.
Skip the test otherwise.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Same as for Spectrum-1, test the ability to add the maximum number of
routes possible to the switch.
Invoke the test from the 'resource_scale' wrapper script.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return the maximum number of tc flower filters that can be offloaded.
Currently, this value corresponds to the number of counters supported by
the driver.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add resource_scale test suitable for Spectrum-2.
Invoke the mirror_gre test and check that the advertised scale numbers
are indeed supported.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like in Spectrum, use the number of analyzers taken from the devlink
command.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't source lib.sh twice and make the script work with ifnames passed
on the command line.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do insertions and removal of filters during rehash in higher volumes.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add checking of newly added trace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Track the basic codepaths of delta rehash handling,
using mlxsw tracepoints. Use IPv6 addresses.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Track the basic codepaths of delta rehash handling,
using mlxsw tracepoints.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that the bug is fixed and we no longer have C-TCAM spill for two
keys that differ only in delta.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With recent fix in C-TCAM spillage for delta masks, the test stops to be
falsely positive. So fix it not to use delta by adding src_ip bits to the
masks. Alongside with that, use C-TCAM spill trace to see when the
spillage actually happens.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow to specify number of trace hits and move helpers
to the beginning of the file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The eRP table is active when there is more than a single rule
pattern. It may be that the patterns are close enough and use delta
mechanism. Bloom filter index computation is based on the values of
{rule & mask, mask ID, region ID} where the rule delta bits must be
cleared.
Add a test that exercises Bloom filter with delta mechanism.
Configure rules within delta range and pass a packet which is
supposed to hit the correct rule.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bloom filter index computation is based on the values of
{rule & mask, mask ID, region ID} and the computation also varies
according to the region key size.
Add a test that exercises the possible combinations by creating
multiple chains using different key sizes and then pass a frame that
is supposed to to produce a hit on all of the regions.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test that exercises Bloom filter code.
Activate eRP table in the region by adding multiple rule patterns which
with very high probability use different entries in the Bloom filter.
Then send packets in order to check lookup hits on all relevant rules.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Track the basic codepaths of delta handling, using objagg tracepoints.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for this to behave as required with delta bits, change the mask
for rule with handle 103.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for this to behave as required with delta bits, change the mask
for rule with handle 103.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Ido Schimmel
Petr Machata
Amit Cohen
Danielle Ratson
Ido Schimmel
Jiri Pirko
Amit Cohen
Danielle Ratson
Petr Machata
Nir Dotan