aboutsummaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
blob: 9802d5d911aa677d656bda23e4b4f4cafd89ea84 (plain) (blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
STMicroelectronics STi MIPHY365x PHY binding
============================================

This binding describes a miphy device that is used to control PHY hardware
for SATA and PCIe.

Required properties (controller (parent) node):
- compatible    : Should be "st,miphy365x-phy"
- st,syscfg     : Phandle / integer array property. Phandle of sysconfig group
		  containing the miphy registers and integer array should contain
		  an entry for each port sub-node, specifying the control
		  register offset inside the sysconfig group.

Required nodes	:  A sub-node is required for each channel the controller
		   provides. Address range information including the usual
		   'reg' and 'reg-names' properties are used inside these
		   nodes to describe the controller's topology. These nodes
		   are translated by the driver's .xlate() function.

Required properties (port (child) node):
- #phy-cells 	: Should be 1 (See second example)
		  Cell after port phandle is device type from:
			- MIPHY_TYPE_SATA
			- MIPHY_TYPE_PCI
- reg        	: Address and length of register sets for each device in
		  "reg-names"
- reg-names     : The names of the register addresses corresponding to the
		  registers filled in "reg":
			- sata:   For SATA devices
			- pcie:   For PCIe devices

Optional properties (port (child) node):
- st,sata-gen	     :	Generation of locally attached SATA IP. Expected values
			are {1,2,3). If not supplied generation 1 hardware will
			be expected
- st,pcie-tx-pol-inv :	Bool property to invert the polarity PCIe Tx (Txn/Txp)
- st,sata-tx-pol-inv :	Bool property to invert the polarity SATA Tx (Txn/Txp)

Example:

	miphy365x_phy: miphy365x@fe382000 {
		compatible      = "st,miphy365x-phy";
		st,syscfg  	= <&syscfg_rear 0x824 0x828>;
		#address-cells	= <1>;
		#size-cells	= <1>;
		ranges;

		phy_port0: port@fe382000 {
			reg = <0xfe382000 0x100>, <0xfe394000 0x100>;
			reg-names = "sata", "pcie";
			#phy-cells = <1>;
			st,sata-gen = <3>;
		};

		phy_port1: port@fe38a000 {
			reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;;
			reg-names = "sata", "pcie", "syscfg";
			#phy-cells = <1>;
			st,pcie-tx-pol-inv;
		};
	};

Specifying phy control of devices
=================================

Device nodes should specify the configuration required in their "phys"
property, containing a phandle to the phy port node and a device type.

Example:

#include <dt-bindings/phy/phy-miphy365x.h>

	sata0: sata@fe380000 {
		...
		phys	  = <&phy_port0 MIPHY_TYPE_SATA>;
		...
	};