aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/ata/pata_bf54x.c
blob: 1e65842e2ca719a0916bc371c676e68f27c096e2 (plain) (blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394
1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
1444
1445
1446
1447
1448
1449
1450
1451
1452
1453
1454
1455
1456
1457
1458
1459
1460
1461
1462
1463
1464
1465
1466
1467
1468
1469
1470
1471
1472
1473
1474
1475
1476
1477
1478
1479
1480
1481
1482
1483
1484
1485
1486
1487
1488
1489
1490
1491
1492
1493
1494
1495
1496
1497
1498
1499
1500
1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515
1516
1517
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538
1539
1540
1541
1542
1543
1544
1545
1546
1547
1548
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
1566
1567
1568
1569
1570
1571
1572
1573
1574
1575
1576
1577
1578
1579
1580
1581
1582
1583
1584
1585
1586
1587
1588
1589
1590
1591
1592
1593
1594
1595
1596
1597
1598
1599
1600
1601
1602
1603
1604
1605
1606
1607
1608
1609
1610
1611
1612
1613
1614
1615
1616
1617
1618
1619
1620
1621
1622
1623
1624
1625
1626
1627
1628
1629
1630
1631
1632
1633
1634
1635
1636
1637
1638
1639
1640
1641
1642
1643
1644
1645
1646
1647
1648
1649
1650
1651
1652
1653
1654
1655
1656
1657
1658
1659
1660
1661
1662
1663
1664
1665
1666
1667
1668
1669
1670
1671
1672
1673
1674
1675
1676
1677
1678
1679
1680
1681
1682
1683
1684
1685
1686
1687
1688
1689
1690
1691
1692
1693
1694
1695
1696
1697
1698
1699
1700
1701
1702
1703
1704
1705
1706
1707
/*
 * File:         drivers/ata/pata_bf54x.c
 * Author:       Sonic Zhang <sonic.zhang@analog.com>
 *
 * Created:
 * Description:  PATA Driver for blackfin 54x
 *
 * Modified:
 *               Copyright 2007 Analog Devices Inc.
 *
 * Bugs:         Enter bugs at http://blackfin.uclinux.org/
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, see the file COPYING, or write
 * to the Free Software Foundation, Inc.,
 * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <linux/platform_device.h>
#include <asm/dma.h>
#include <asm/gpio.h>
#include <asm/portmux.h>

#define DRV_NAME		"pata-bf54x"
#define DRV_VERSION		"0.9"

#define ATA_REG_CTRL		0x0E
#define ATA_REG_ALTSTATUS	ATA_REG_CTRL

/* These are the offset of the controller's registers */
#define ATAPI_OFFSET_CONTROL		0x00
#define ATAPI_OFFSET_STATUS		0x04
#define ATAPI_OFFSET_DEV_ADDR		0x08
#define ATAPI_OFFSET_DEV_TXBUF		0x0c
#define ATAPI_OFFSET_DEV_RXBUF		0x10
#define ATAPI_OFFSET_INT_MASK		0x14
#define ATAPI_OFFSET_INT_STATUS		0x18
#define ATAPI_OFFSET_XFER_LEN		0x1c
#define ATAPI_OFFSET_LINE_STATUS	0x20
#define ATAPI_OFFSET_SM_STATE		0x24
#define ATAPI_OFFSET_TERMINATE		0x28
#define ATAPI_OFFSET_PIO_TFRCNT		0x2c
#define ATAPI_OFFSET_DMA_TFRCNT		0x30
#define ATAPI_OFFSET_UMAIN_TFRCNT	0x34
#define ATAPI_OFFSET_UDMAOUT_TFRCNT	0x38
#define ATAPI_OFFSET_REG_TIM_0		0x40
#define ATAPI_OFFSET_PIO_TIM_0		0x44
#define ATAPI_OFFSET_PIO_TIM_1		0x48
#define ATAPI_OFFSET_MULTI_TIM_0	0x50
#define ATAPI_OFFSET_MULTI_TIM_1	0x54
#define ATAPI_OFFSET_MULTI_TIM_2	0x58
#define ATAPI_OFFSET_ULTRA_TIM_0	0x60
#define ATAPI_OFFSET_ULTRA_TIM_1	0x64
#define ATAPI_OFFSET_ULTRA_TIM_2	0x68
#define ATAPI_OFFSET_ULTRA_TIM_3	0x6c


#define ATAPI_GET_CONTROL(base)\
	bfin_read16(base + ATAPI_OFFSET_CONTROL)
#define ATAPI_SET_CONTROL(base, val)\
	bfin_write16(base + ATAPI_OFFSET_CONTROL, val)
#define ATAPI_GET_STATUS(base)\
	bfin_read16(base + ATAPI_OFFSET_STATUS)
#define ATAPI_GET_DEV_ADDR(base)\
	bfin_read16(base + ATAPI_OFFSET_DEV_ADDR)
#define ATAPI_SET_DEV_ADDR(base, val)\
	bfin_write16(base + ATAPI_OFFSET_DEV_ADDR, val)
#define ATAPI_GET_DEV_TXBUF(base)\
	bfin_read16(base + ATAPI_OFFSET_DEV_TXBUF)
#define ATAPI_SET_DEV_TXBUF(base, val)\
	bfin_write16(base + ATAPI_OFFSET_DEV_TXBUF, val)
#define ATAPI_GET_DEV_RXBUF(base)\
	bfin_read16(base + ATAPI_OFFSET_DEV_RXBUF)
#define ATAPI_SET_DEV_RXBUF(base, val)\
	bfin_write16(base + ATAPI_OFFSET_DEV_RXBUF, val)
#define ATAPI_GET_INT_MASK(base)\
	bfin_read16(base + ATAPI_OFFSET_INT_MASK)
#define ATAPI_SET_INT_MASK(base, val)\
	bfin_write16(base + ATAPI_OFFSET_INT_MASK, val)
#define ATAPI_GET_INT_STATUS(base)\
	bfin_read16(base + ATAPI_OFFSET_INT_STATUS)
#define ATAPI_SET_INT_STATUS(base, val)\
	bfin_write16(base + ATAPI_OFFSET_INT_STATUS, val)
#define ATAPI_GET_XFER_LEN(base)\
	bfin_read16(base + ATAPI_OFFSET_XFER_LEN)
#define ATAPI_SET_XFER_LEN(base, val)\
	bfin_write16(base + ATAPI_OFFSET_XFER_LEN, val)
#define ATAPI_GET_LINE_STATUS(base)\
	bfin_read16(base + ATAPI_OFFSET_LINE_STATUS)
#define ATAPI_GET_SM_STATE(base)\
	bfin_read16(base + ATAPI_OFFSET_SM_STATE)
#define ATAPI_GET_TERMINATE(base)\
	bfin_read16(base + ATAPI_OFFSET_TERMINATE)
#define ATAPI_SET_TERMINATE(base, val)\
	bfin_write16(base + ATAPI_OFFSET_TERMINATE, val)
#define ATAPI_GET_PIO_TFRCNT(base)\
	bfin_read16(base + ATAPI_OFFSET_PIO_TFRCNT)
#define ATAPI_GET_DMA_TFRCNT(base)\
	bfin_read16(base + ATAPI_OFFSET_DMA_TFRCNT)
#define ATAPI_GET_UMAIN_TFRCNT(base)\
	bfin_read16(base + ATAPI_OFFSET_UMAIN_TFRCNT)
#define ATAPI_GET_UDMAOUT_TFRCNT(base)\
	bfin_read16(base + ATAPI_OFFSET_UDMAOUT_TFRCNT)
#define ATAPI_GET_REG_TIM_0(base)\
	bfin_read16(base + ATAPI_OFFSET_REG_TIM_0)
#define ATAPI_SET_REG_TIM_0(base, val)\
	bfin_write16(base + ATAPI_OFFSET_REG_TIM_0, val)
#define ATAPI_GET_PIO_TIM_0(base)\
	bfin_read16(base + ATAPI_OFFSET_PIO_TIM_0)
#define ATAPI_SET_PIO_TIM_0(base, val)\
	bfin_write16(base + ATAPI_OFFSET_PIO_TIM_0, val)
#define ATAPI_GET_PIO_TIM_1(base)\
	bfin_read16(base + ATAPI_OFFSET_PIO_TIM_1)
#define ATAPI_SET_PIO_TIM_1(base, val)\
	bfin_write16(base + ATAPI_OFFSET_PIO_TIM_1, val)
#define ATAPI_GET_MULTI_TIM_0(base)\
	bfin_read16(base + ATAPI_OFFSET_MULTI_TIM_0)
#define ATAPI_SET_MULTI_TIM_0(base, val)\
	bfin_write16(base + ATAPI_OFFSET_MULTI_TIM_0, val)
#define ATAPI_GET_MULTI_TIM_1(base)\
	bfin_read16(base + ATAPI_OFFSET_MULTI_TIM_1)
#define ATAPI_SET_MULTI_TIM_1(base, val)\
	bfin_write16(base + ATAPI_OFFSET_MULTI_TIM_1, val)
#define ATAPI_GET_MULTI_TIM_2(base)\
	bfin_read16(base + ATAPI_OFFSET_MULTI_TIM_2)
#define ATAPI_SET_MULTI_TIM_2(base, val)\
	bfin_write16(base + ATAPI_OFFSET_MULTI_TIM_2, val)
#define ATAPI_GET_ULTRA_TIM_0(base)\
	bfin_read16(base + ATAPI_OFFSET_ULTRA_TIM_0)
#define ATAPI_SET_ULTRA_TIM_0(base, val)\
	bfin_write16(base + ATAPI_OFFSET_ULTRA_TIM_0, val)
#define ATAPI_GET_ULTRA_TIM_1(base)\
	bfin_read16(base + ATAPI_OFFSET_ULTRA_TIM_1)
#define ATAPI_SET_ULTRA_TIM_1(base, val)\
	bfin_write16(base + ATAPI_OFFSET_ULTRA_TIM_1, val)
#define ATAPI_GET_ULTRA_TIM_2(base)\
	bfin_read16(base + ATAPI_OFFSET_ULTRA_TIM_2)
#define ATAPI_SET_ULTRA_TIM_2(base, val)\
	bfin_write16(base + ATAPI_OFFSET_ULTRA_TIM_2, val)
#define ATAPI_GET_ULTRA_TIM_3(base)\
	bfin_read16(base + ATAPI_OFFSET_ULTRA_TIM_3)
#define ATAPI_SET_ULTRA_TIM_3(base, val)\
	bfin_write16(base + ATAPI_OFFSET_ULTRA_TIM_3, val)

/**
 * PIO Mode - Frequency compatibility
 */
/* mode: 0         1         2         3         4 */
static const u32 pio_fsclk[] =
{ 33333333, 33333333, 33333333, 33333333, 33333333 };

/**
 * MDMA Mode - Frequency compatibility
 */
/*               mode:      0         1         2        */
static const u32 mdma_fsclk[] = { 33333333, 33333333, 33333333 };

/**
 * UDMA Mode - Frequency compatibility
 *
 * UDMA5 - 100 MB/s   - SCLK  = 133 MHz
 * UDMA4 - 66 MB/s    - SCLK >=  80 MHz
 * UDMA3 - 44.4 MB/s  - SCLK >=  50 MHz
 * UDMA2 - 33 MB/s    - SCLK >=  40 MHz
 */
/* mode: 0         1         2         3         4          5 */
static const u32 udma_fsclk[] =
{ 33333333, 33333333, 40000000, 50000000, 80000000, 133333333 };

/**
 * Register transfer timing table
 */
/*               mode:       0    1    2    3    4    */
/* Cycle Time                     */
static const u32 reg_t0min[]   = { 600, 383, 330, 180, 120 };
/* DIOR/DIOW to end cycle         */
static const u32 reg_t2min[]   = { 290, 290, 290, 70,  25  };
/* DIOR/DIOW asserted pulse width */
static const u32 reg_teocmin[] = { 290, 290, 290, 80,  70  };

/**
 * PIO timing table
 */
/*               mode:       0    1    2    3    4    */
/* Cycle Time                     */
static const u32 pio_t0min[]   = { 600, 383, 240, 180, 120 };
/* Address valid to DIOR/DIORW    */
static const u32 pio_t1min[]   = { 70,  50,  30,  30,  25  };
/* DIOR/DIOW to end cycle         */
static const u32 pio_t2min[]   = { 165, 125, 100, 80,  70  };
/* DIOR/DIOW asserted pulse width */
static const u32 pio_teocmin[] = { 165, 125, 100, 70,  25  };
/* DIOW data hold                 */
static const u32 pio_t4min[]   = { 30,  20,  15,  10,  10  };

/* ******************************************************************
 * Multiword DMA timing table
 * ******************************************************************
 */
/*               mode:       0   1    2        */
/* Cycle Time                     */
static const u32 mdma_t0min[]  = { 480, 150, 120 };
/* DIOR/DIOW asserted pulse width */
static const u32 mdma_tdmin[]  = { 215, 80,  70  };
/* DMACK to read data released    */
static const u32 mdma_thmin[]  = { 20,  15,  10  };
/* DIOR/DIOW to DMACK hold        */
static const u32 mdma_tjmin[]  = { 20,  5,   5   };
/* DIOR negated pulse width       */
static const u32 mdma_tkrmin[] = { 50,  50,  25  };
/* DIOR negated pulse width       */
static const u32 mdma_tkwmin[] = { 215, 50,  25  };
/* CS[1:0] valid to DIOR/DIOW     */
static const u32 mdma_tmmin[]  = { 50,  30,  25  };
/* DMACK to read data released    */
static const u32 mdma_tzmax[]  = { 20,  25,  25  };

/**
 * Ultra DMA timing table
 */
/*               mode:         0    1    2    3    4    5       */
static const u32 udma_tcycmin[]  = { 112, 73,  54,  39,  25,  17 };
static const u32 udma_tdvsmin[]  = { 70,  48,  31,  20,  7,   5  };
static const u32 udma_tenvmax[]  = { 70,  70,  70,  55,  55,  50 };
static const u32 udma_trpmin[]   = { 160, 125, 100, 100, 100, 85 };
static const u32 udma_tmin[]     = { 5,   5,   5,   5,   3,   3  };


static const u32 udma_tmlimin = 20;
static const u32 udma_tzahmin = 20;
static const u32 udma_tenvmin = 20;
static const u32 udma_tackmin = 20;
static const u32 udma_tssmin = 50;

#define BFIN_MAX_SG_SEGMENTS 4

/**
 *
 *	Function:       num_clocks_min
 *
 *	Description:
 *	calculate number of SCLK cycles to meet minimum timing
 */
static unsigned short num_clocks_min(unsigned long tmin,
				unsigned long fsclk)
{
	unsigned long tmp ;
	unsigned short result;

	tmp = tmin * (fsclk/1000/1000) / 1000;
	result = (unsigned short)tmp;
	if ((tmp*1000*1000) < (tmin*(fsclk/1000))) {
		result++;
	}

	return result;
}

/**
 *	bfin_set_piomode - Initialize host controller PATA PIO timings
 *	@ap: Port whose timings we are configuring
 *	@adev: um
 *
 *	Set PIO mode for device.
 *
 *	LOCKING:
 *	None (inherited from caller).
 */

static void bfin_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	int mode = adev->pio_mode - XFER_PIO_0;
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	unsigned int fsclk = get_sclk();
	unsigned short teoc_reg, t2_reg, teoc_pio;
	unsigned short t4_reg, t2_pio, t1_reg;
	unsigned short n0, n6, t6min = 5;

	/* the most restrictive timing value is t6 and tc, the DIOW - data hold
	* If one SCLK pulse is longer than this minimum value then register
	* transfers cannot be supported at this frequency.
	*/
	n6 = num_clocks_min(t6min, fsclk);
	if (mode >= 0 && mode <= 4 && n6 >= 1) {
		dev_dbg(adev->link->ap->dev, "set piomode: mode=%d, fsclk=%ud\n", mode, fsclk);
		/* calculate the timing values for register transfers. */
		while (mode > 0 && pio_fsclk[mode] > fsclk)
			mode--;

		/* DIOR/DIOW to end cycle time */
		t2_reg = num_clocks_min(reg_t2min[mode], fsclk);
		/* DIOR/DIOW asserted pulse width */
		teoc_reg = num_clocks_min(reg_teocmin[mode], fsclk);
		/* Cycle Time */
		n0  = num_clocks_min(reg_t0min[mode], fsclk);

		/* increase t2 until we meed the minimum cycle length */
		if (t2_reg + teoc_reg < n0)
			t2_reg = n0 - teoc_reg;

		/* calculate the timing values for pio transfers. */

		/* DIOR/DIOW to end cycle time */
		t2_pio = num_clocks_min(pio_t2min[mode], fsclk);
		/* DIOR/DIOW asserted pulse width */
		teoc_pio = num_clocks_min(pio_teocmin[mode], fsclk);
		/* Cycle Time */
		n0  = num_clocks_min(pio_t0min[mode], fsclk);

		/* increase t2 until we meed the minimum cycle length */
		if (t2_pio + teoc_pio < n0)
			t2_pio = n0 - teoc_pio;

		/* Address valid to DIOR/DIORW */
		t1_reg = num_clocks_min(pio_t1min[mode], fsclk);

		/* DIOW data hold */
		t4_reg = num_clocks_min(pio_t4min[mode], fsclk);

		ATAPI_SET_REG_TIM_0(base, (teoc_reg<<8 | t2_reg));
		ATAPI_SET_PIO_TIM_0(base, (t4_reg<<12 | t2_pio<<4 | t1_reg));
		ATAPI_SET_PIO_TIM_1(base, teoc_pio);
		if (mode > 2) {
			ATAPI_SET_CONTROL(base,
				ATAPI_GET_CONTROL(base) | IORDY_EN);
		} else {
			ATAPI_SET_CONTROL(base,
				ATAPI_GET_CONTROL(base) & ~IORDY_EN);
		}

		/* Disable host ATAPI PIO interrupts */
		ATAPI_SET_INT_MASK(base, ATAPI_GET_INT_MASK(base)
			& ~(PIO_DONE_MASK | HOST_TERM_XFER_MASK));
		SSYNC();
	}
}

/**
 *	bfin_set_dmamode - Initialize host controller PATA DMA timings
 *	@ap: Port whose timings we are configuring
 *	@adev: um
 *
 *	Set UDMA mode for device.
 *
 *	LOCKING:
 *	None (inherited from caller).
 */

static void bfin_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
	int mode;
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	unsigned long fsclk = get_sclk();
	unsigned short tenv, tack, tcyc_tdvs, tdvs, tmli, tss, trp, tzah;
	unsigned short tm, td, tkr, tkw, teoc, th;
	unsigned short n0, nf, tfmin = 5;
	unsigned short nmin, tcyc;

	mode = adev->dma_mode - XFER_UDMA_0;
	if (mode >= 0 && mode <= 5) {
		dev_dbg(adev->link->ap->dev, "set udmamode: mode=%d\n", mode);
		/* the most restrictive timing value is t6 and tc,
		 * the DIOW - data hold. If one SCLK pulse is longer
		 * than this minimum value then register
		 * transfers cannot be supported at this frequency.
		 */
		while (mode > 0 && udma_fsclk[mode] > fsclk)
			mode--;

		nmin = num_clocks_min(udma_tmin[mode], fsclk);
		if (nmin >= 1) {
			/* calculate the timing values for Ultra DMA. */
			tdvs = num_clocks_min(udma_tdvsmin[mode], fsclk);
			tcyc = num_clocks_min(udma_tcycmin[mode], fsclk);
			tcyc_tdvs = 2;

			/* increase tcyc - tdvs (tcyc_tdvs) until we meed
			 * the minimum cycle length
			 */
			if (tdvs + tcyc_tdvs < tcyc)
				tcyc_tdvs = tcyc - tdvs;

			/* Mow assign the values required for the timing
			 * registers
			 */
			if (tcyc_tdvs < 2)
				tcyc_tdvs = 2;

			if (tdvs < 2)
				tdvs = 2;

			tack = num_clocks_min(udma_tackmin, fsclk);
			tss = num_clocks_min(udma_tssmin, fsclk);
			tmli = num_clocks_min(udma_tmlimin, fsclk);
			tzah = num_clocks_min(udma_tzahmin, fsclk);
			trp = num_clocks_min(udma_trpmin[mode], fsclk);
			tenv = num_clocks_min(udma_tenvmin, fsclk);
			if (tenv <= udma_tenvmax[mode]) {
				ATAPI_SET_ULTRA_TIM_0(base, (tenv<<8 | tack));
				ATAPI_SET_ULTRA_TIM_1(base,
					(tcyc_tdvs<<8 | tdvs));
				ATAPI_SET_ULTRA_TIM_2(base, (tmli<<8 | tss));
				ATAPI_SET_ULTRA_TIM_3(base, (trp<<8 | tzah));
			}
		}
	}

	mode = adev->dma_mode - XFER_MW_DMA_0;
	if (mode >= 0 && mode <= 2) {
		dev_dbg(adev->link->ap->dev, "set mdmamode: mode=%d\n", mode);
		/* the most restrictive timing value is tf, the DMACK to
		 * read data released. If one SCLK pulse is longer than
		 * this maximum value then the MDMA mode
		 * cannot be supported at this frequency.
		 */
		while (mode > 0 && mdma_fsclk[mode] > fsclk)
			mode--;

		nf = num_clocks_min(tfmin, fsclk);
		if (nf >= 1) {
			/* calculate the timing values for Multi-word DMA. */

			/* DIOR/DIOW asserted pulse width */
			td = num_clocks_min(mdma_tdmin[mode], fsclk);

			/* DIOR negated pulse width */
			tkw = num_clocks_min(mdma_tkwmin[mode], fsclk);

			/* Cycle Time */
			n0  = num_clocks_min(mdma_t0min[mode], fsclk);

			/* increase tk until we meed the minimum cycle length */
			if (tkw + td < n0)
				tkw = n0 - td;

			/* DIOR negated pulse width - read */
			tkr = num_clocks_min(mdma_tkrmin[mode], fsclk);
			/* CS{1:0] valid to DIOR/DIOW */
			tm = num_clocks_min(mdma_tmmin[mode], fsclk);
			/* DIOR/DIOW to DMACK hold */
			teoc = num_clocks_min(mdma_tjmin[mode], fsclk);
			/* DIOW Data hold */
			th = num_clocks_min(mdma_thmin[mode], fsclk);

			ATAPI_SET_MULTI_TIM_0(base, (tm<<8 | td));
			ATAPI_SET_MULTI_TIM_1(base, (tkr<<8 | tkw));
			ATAPI_SET_MULTI_TIM_2(base, (teoc<<8 | th));
			SSYNC();
		}
	}
	return;
}

/**
 *
 *    Function:       wait_complete
 *
 *    Description:    Waits the interrupt from device
 *
 */
static inline void wait_complete(void __iomem *base, unsigned short mask)
{
	unsigned short status;
	unsigned int i = 0;

#define PATA_BF54X_WAIT_TIMEOUT		10000

	for (i = 0; i < PATA_BF54X_WAIT_TIMEOUT; i++) {
		status = ATAPI_GET_INT_STATUS(base) & mask;
		if (status)
			break;
	}

	ATAPI_SET_INT_STATUS(base, mask);
}

/**
 *
 *    Function:       write_atapi_register
 *
 *    Description:    Writes to ATA Device Resgister
 *
 */

static void write_atapi_register(void __iomem *base,
		unsigned long ata_reg, unsigned short value)
{
	/* Program the ATA_DEV_TXBUF register with write data (to be
	 * written into the device).
	 */
	ATAPI_SET_DEV_TXBUF(base, value);

	/* Program the ATA_DEV_ADDR register with address of the
	 * device register (0x01 to 0x0F).
	 */
	ATAPI_SET_DEV_ADDR(base, ata_reg);

	/* Program the ATA_CTRL register with dir set to write (1)
	 */
	ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | XFER_DIR));

	/* ensure PIO DMA is not set */
	ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~PIO_USE_DMA));

	/* and start the transfer */
	ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | PIO_START));

	/* Wait for the interrupt to indicate the end of the transfer.
	 * (We need to wait on and clear rhe ATA_DEV_INT interrupt status)
	 */
	wait_complete(base, PIO_DONE_INT);
}

/**
 *
 *	Function:       read_atapi_register
 *
 *Description:    Reads from ATA Device Resgister
 *
 */

static unsigned short read_atapi_register(void __iomem *base,
		unsigned long ata_reg)
{
	/* Program the ATA_DEV_ADDR register with address of the
	 * device register (0x01 to 0x0F).
	 */
	ATAPI_SET_DEV_ADDR(base, ata_reg);

	/* Program the ATA_CTRL register with dir set to read (0) and
	 */
	ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~XFER_DIR));

	/* ensure PIO DMA is not set */
	ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~PIO_USE_DMA));

	/* and start the transfer */
	ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | PIO_START));

	/* Wait for the interrupt to indicate the end of the transfer.
	 * (PIO_DONE interrupt is set and it doesn't seem to matter
	 * that we don't clear it)
	 */
	wait_complete(base, PIO_DONE_INT);

	/* Read the ATA_DEV_RXBUF register with write data (to be
	 * written into the device).
	 */
	return ATAPI_GET_DEV_RXBUF(base);
}

/**
 *
 *    Function:       write_atapi_register_data
 *
 *    Description:    Writes to ATA Device Resgister
 *
 */

static void write_atapi_data(void __iomem *base,
		int len, unsigned short *buf)
{
	int i;

	/* Set transfer length to 1 */
	ATAPI_SET_XFER_LEN(base, 1);

	/* Program the ATA_DEV_ADDR register with address of the
	 * ATA_REG_DATA
	 */
	ATAPI_SET_DEV_ADDR(base, ATA_REG_DATA);

	/* Program the ATA_CTRL register with dir set to write (1)
	 */
	ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | XFER_DIR));

	/* ensure PIO DMA is not set */
	ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~PIO_USE_DMA));

	for (i = 0; i < len; i++) {
		/* Program the ATA_DEV_TXBUF register with write data (to be
		 * written into the device).
		 */
		ATAPI_SET_DEV_TXBUF(base, buf[i]);

		/* and start the transfer */
		ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | PIO_START));

		/* Wait for the interrupt to indicate the end of the transfer.
		 * (We need to wait on and clear rhe ATA_DEV_INT
		 * interrupt status)
		 */
		wait_complete(base, PIO_DONE_INT);
	}
}

/**
 *
 *	Function:       read_atapi_register_data
 *
 *	Description:    Reads from ATA Device Resgister
 *
 */

static void read_atapi_data(void __iomem *base,
		int len, unsigned short *buf)
{
	int i;

	/* Set transfer length to 1 */
	ATAPI_SET_XFER_LEN(base, 1);

	/* Program the ATA_DEV_ADDR register with address of the
	 * ATA_REG_DATA
	 */
	ATAPI_SET_DEV_ADDR(base, ATA_REG_DATA);

	/* Program the ATA_CTRL register with dir set to read (0) and
	 */
	ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~XFER_DIR));

	/* ensure PIO DMA is not set */
	ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) & ~PIO_USE_DMA));

	for (i = 0; i < len; i++) {
		/* and start the transfer */
		ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base) | PIO_START));

		/* Wait for the interrupt to indicate the end of the transfer.
		 * (PIO_DONE interrupt is set and it doesn't seem to matter
		 * that we don't clear it)
		 */
		wait_complete(base, PIO_DONE_INT);

		/* Read the ATA_DEV_RXBUF register with write data (to be
		 * written into the device).
		 */
		buf[i] = ATAPI_GET_DEV_RXBUF(base);
	}
}

/**
 *	bfin_tf_load - send taskfile registers to host controller
 *	@ap: Port to which output is sent
 *	@tf: ATA taskfile register set
 *
 *	Note: Original code is ata_sff_tf_load().
 */

static void bfin_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
{
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;

	if (tf->ctl != ap->last_ctl) {
		write_atapi_register(base, ATA_REG_CTRL, tf->ctl);
		ap->last_ctl = tf->ctl;
		ata_wait_idle(ap);
	}

	if (is_addr) {
		if (tf->flags & ATA_TFLAG_LBA48) {
			write_atapi_register(base, ATA_REG_FEATURE,
						tf->hob_feature);
			write_atapi_register(base, ATA_REG_NSECT,
						tf->hob_nsect);
			write_atapi_register(base, ATA_REG_LBAL, tf->hob_lbal);
			write_atapi_register(base, ATA_REG_LBAM, tf->hob_lbam);
			write_atapi_register(base, ATA_REG_LBAH, tf->hob_lbah);
			dev_dbg(ap->dev, "hob: feat 0x%X nsect 0x%X, lba 0x%X "
				 "0x%X 0x%X\n",
				tf->hob_feature,
				tf->hob_nsect,
				tf->hob_lbal,
				tf->hob_lbam,
				tf->hob_lbah);
		}

		write_atapi_register(base, ATA_REG_FEATURE, tf->feature);
		write_atapi_register(base, ATA_REG_NSECT, tf->nsect);
		write_atapi_register(base, ATA_REG_LBAL, tf->lbal);
		write_atapi_register(base, ATA_REG_LBAM, tf->lbam);
		write_atapi_register(base, ATA_REG_LBAH, tf->lbah);
		dev_dbg(ap->dev, "feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
			tf->feature,
			tf->nsect,
			tf->lbal,
			tf->lbam,
			tf->lbah);
	}

	if (tf->flags & ATA_TFLAG_DEVICE) {
		write_atapi_register(base, ATA_REG_DEVICE, tf->device);
		dev_dbg(ap->dev, "device 0x%X\n", tf->device);
	}

	ata_wait_idle(ap);
}

/**
 *	bfin_check_status - Read device status reg & clear interrupt
 *	@ap: port where the device is
 *
 *	Note: Original code is ata_check_status().
 */

static u8 bfin_check_status(struct ata_port *ap)
{
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	return read_atapi_register(base, ATA_REG_STATUS);
}

/**
 *	bfin_tf_read - input device's ATA taskfile shadow registers
 *	@ap: Port from which input is read
 *	@tf: ATA taskfile register set for storing input
 *
 *	Note: Original code is ata_sff_tf_read().
 */

static void bfin_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
{
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;

	tf->command = bfin_check_status(ap);
	tf->feature = read_atapi_register(base, ATA_REG_ERR);
	tf->nsect = read_atapi_register(base, ATA_REG_NSECT);
	tf->lbal = read_atapi_register(base, ATA_REG_LBAL);
	tf->lbam = read_atapi_register(base, ATA_REG_LBAM);
	tf->lbah = read_atapi_register(base, ATA_REG_LBAH);
	tf->device = read_atapi_register(base, ATA_REG_DEVICE);

	if (tf->flags & ATA_TFLAG_LBA48) {
		write_atapi_register(base, ATA_REG_CTRL, tf->ctl | ATA_HOB);
		tf->hob_feature = read_atapi_register(base, ATA_REG_ERR);
		tf->hob_nsect = read_atapi_register(base, ATA_REG_NSECT);
		tf->hob_lbal = read_atapi_register(base, ATA_REG_LBAL);
		tf->hob_lbam = read_atapi_register(base, ATA_REG_LBAM);
		tf->hob_lbah = read_atapi_register(base, ATA_REG_LBAH);
	}
}

/**
 *	bfin_exec_command - issue ATA command to host controller
 *	@ap: port to which command is being issued
 *	@tf: ATA taskfile register set
 *
 *	Note: Original code is ata_sff_exec_command().
 */

static void bfin_exec_command(struct ata_port *ap,
			      const struct ata_taskfile *tf)
{
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	dev_dbg(ap->dev, "ata%u: cmd 0x%X\n", ap->print_id, tf->command);

	write_atapi_register(base, ATA_REG_CMD, tf->command);
	ata_sff_pause(ap);
}

/**
 *	bfin_check_altstatus - Read device alternate status reg
 *	@ap: port where the device is
 */

static u8 bfin_check_altstatus(struct ata_port *ap)
{
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	return read_atapi_register(base, ATA_REG_ALTSTATUS);
}

/**
 *	bfin_dev_select - Select device 0/1 on ATA bus
 *	@ap: ATA channel to manipulate
 *	@device: ATA device (numbered from zero) to select
 *
 *	Note: Original code is ata_sff_dev_select().
 */

static void bfin_dev_select(struct ata_port *ap, unsigned int device)
{
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	u8 tmp;

	if (device == 0)
		tmp = ATA_DEVICE_OBS;
	else
		tmp = ATA_DEVICE_OBS | ATA_DEV1;

	write_atapi_register(base, ATA_REG_DEVICE, tmp);
	ata_sff_pause(ap);
}

/**
 *	bfin_set_devctl - Write device control reg
 *	@ap: port where the device is
 *	@ctl: value to write
 */

static void bfin_set_devctl(struct ata_port *ap, u8 ctl)
{
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	write_atapi_register(base, ATA_REG_CTRL, ctl);
}

/**
 *	bfin_bmdma_setup - Set up IDE DMA transaction
 *	@qc: Info associated with this ATA transaction.
 *
 *	Note: Original code is ata_bmdma_setup().
 */

static void bfin_bmdma_setup(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;
	struct dma_desc_array *dma_desc_cpu = (struct dma_desc_array *)ap->bmdma_prd;
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	unsigned short config = DMAFLOW_ARRAY | NDSIZE_5 | RESTART | WDSIZE_16 | DMAEN;
	struct scatterlist *sg;
	unsigned int si;
	unsigned int channel;
	unsigned int dir;
	unsigned int size = 0;

	dev_dbg(qc->ap->dev, "in atapi dma setup\n");
	/* Program the ATA_CTRL register with dir */
	if (qc->tf.flags & ATA_TFLAG_WRITE) {
		channel = CH_ATAPI_TX;
		dir = DMA_TO_DEVICE;
	} else {
		channel = CH_ATAPI_RX;
		dir = DMA_FROM_DEVICE;
		config |= WNR;
	}

	dma_map_sg(ap->dev, qc->sg, qc->n_elem, dir);

	/* fill the ATAPI DMA controller */
	for_each_sg(qc->sg, sg, qc->n_elem, si) {
		dma_desc_cpu[si].start_addr = sg_dma_address(sg);
		dma_desc_cpu[si].cfg = config;
		dma_desc_cpu[si].x_count = sg_dma_len(sg) >> 1;
		dma_desc_cpu[si].x_modify = 2;
		size += sg_dma_len(sg);
	}

	/* Set the last descriptor to stop mode */
	dma_desc_cpu[qc->n_elem - 1].cfg &= ~(DMAFLOW | NDSIZE);

	flush_dcache_range((unsigned int)dma_desc_cpu,
		(unsigned int)dma_desc_cpu +
			qc->n_elem * sizeof(struct dma_desc_array));

	/* Enable ATA DMA operation*/
	set_dma_curr_desc_addr(channel, (unsigned long *)ap->bmdma_prd_dma);
	set_dma_x_count(channel, 0);
	set_dma_x_modify(channel, 0);
	set_dma_config(channel, config);

	SSYNC();

	/* Send ATA DMA command */
	bfin_exec_command(ap, &qc->tf);

	if (qc->tf.flags & ATA_TFLAG_WRITE) {
		/* set ATA DMA write direction */
		ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base)
			| XFER_DIR));
	} else {
		/* set ATA DMA read direction */
		ATAPI_SET_CONTROL(base, (ATAPI_GET_CONTROL(base)
			& ~XFER_DIR));
	}

	/* Reset all transfer count */
	ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base) | TFRCNT_RST);

	/* Set ATAPI state machine contorl in terminate sequence */
	ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base) | END_ON_TERM);

	/* Set transfer length to the total size of sg buffers */
	ATAPI_SET_XFER_LEN(base, size >> 1);
}

/**
 *	bfin_bmdma_start - Start an IDE DMA transaction
 *	@qc: Info associated with this ATA transaction.
 *
 *	Note: Original code is ata_bmdma_start().
 */

static void bfin_bmdma_start(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;

	dev_dbg(qc->ap->dev, "in atapi dma start\n");

	if (!(ap->udma_mask || ap->mwdma_mask))
		return;

	/* start ATAPI transfer*/
	if (ap->udma_mask)
		ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base)
			| ULTRA_START);
	else
		ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base)
			| MULTI_START);
}

/**
 *	bfin_bmdma_stop - Stop IDE DMA transfer
 *	@qc: Command we are ending DMA for
 */

static void bfin_bmdma_stop(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;
	unsigned int dir;

	dev_dbg(qc->ap->dev, "in atapi dma stop\n");

	if (!(ap->udma_mask || ap->mwdma_mask))
		return;

	/* stop ATAPI DMA controller*/
	if (qc->tf.flags & ATA_TFLAG_WRITE) {
		dir = DMA_TO_DEVICE;
		disable_dma(CH_ATAPI_TX);
	} else {
		dir = DMA_FROM_DEVICE;
		disable_dma(CH_ATAPI_RX);
	}

	dma_unmap_sg(ap->dev, qc->sg, qc->n_elem, dir);
}

/**
 *	bfin_devchk - PATA device presence detection
 *	@ap: ATA channel to examine
 *	@device: Device to examine (starting at zero)
 *
 *	Note: Original code is ata_devchk().
 */

static unsigned int bfin_devchk(struct ata_port *ap,
				unsigned int device)
{
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	u8 nsect, lbal;

	bfin_dev_select(ap, device);

	write_atapi_register(base, ATA_REG_NSECT, 0x55);
	write_atapi_register(base, ATA_REG_LBAL, 0xaa);

	write_atapi_register(base, ATA_REG_NSECT, 0xaa);
	write_atapi_register(base, ATA_REG_LBAL, 0x55);

	write_atapi_register(base, ATA_REG_NSECT, 0x55);
	write_atapi_register(base, ATA_REG_LBAL, 0xaa);

	nsect = read_atapi_register(base, ATA_REG_NSECT);
	lbal = read_atapi_register(base, ATA_REG_LBAL);

	if ((nsect == 0x55) && (lbal == 0xaa))
		return 1;	/* we found a device */

	return 0;		/* nothing found */
}

/**
 *	bfin_bus_post_reset - PATA device post reset
 *
 *	Note: Original code is ata_bus_post_reset().
 */

static void bfin_bus_post_reset(struct ata_port *ap, unsigned int devmask)
{
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	unsigned int dev0 = devmask & (1 << 0);
	unsigned int dev1 = devmask & (1 << 1);
	unsigned long deadline;

	/* if device 0 was found in ata_devchk, wait for its
	 * BSY bit to clear
	 */
	if (dev0)
		ata_sff_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);

	/* if device 1 was found in ata_devchk, wait for
	 * register access, then wait for BSY to clear
	 */
	deadline = ata_deadline(jiffies, ATA_TMOUT_BOOT);
	while (dev1) {
		u8 nsect, lbal;

		bfin_dev_select(ap, 1);
		nsect = read_atapi_register(base, ATA_REG_NSECT);
		lbal = read_atapi_register(base, ATA_REG_LBAL);
		if ((nsect == 1) && (lbal == 1))
			break;
		if (time_after(jiffies, deadline)) {
			dev1 = 0;
			break;
		}
		ata_msleep(ap, 50);	/* give drive a breather */
	}
	if (dev1)
		ata_sff_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);

	/* is all this really necessary? */
	bfin_dev_select(ap, 0);
	if (dev1)
		bfin_dev_select(ap, 1);
	if (dev0)
		bfin_dev_select(ap, 0);
}

/**
 *	bfin_bus_softreset - PATA device software reset
 *
 *	Note: Original code is ata_bus_softreset().
 */

static unsigned int bfin_bus_softreset(struct ata_port *ap,
				       unsigned int devmask)
{
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;

	/* software reset.  causes dev0 to be selected */
	write_atapi_register(base, ATA_REG_CTRL, ap->ctl);
	udelay(20);
	write_atapi_register(base, ATA_REG_CTRL, ap->ctl | ATA_SRST);
	udelay(20);
	write_atapi_register(base, ATA_REG_CTRL, ap->ctl);

	/* spec mandates ">= 2ms" before checking status.
	 * We wait 150ms, because that was the magic delay used for
	 * ATAPI devices in Hale Landis's ATADRVR, for the period of time
	 * between when the ATA command register is written, and then
	 * status is checked.  Because waiting for "a while" before
	 * checking status is fine, post SRST, we perform this magic
	 * delay here as well.
	 *
	 * Old drivers/ide uses the 2mS rule and then waits for ready
	 */
	ata_msleep(ap, 150);

	/* Before we perform post reset processing we want to see if
	 * the bus shows 0xFF because the odd clown forgets the D7
	 * pulldown resistor.
	 */
	if (bfin_check_status(ap) == 0xFF)
		return 0;

	bfin_bus_post_reset(ap, devmask);

	return 0;
}

/**
 *	bfin_softreset - reset host port via ATA SRST
 *	@ap: port to reset
 *	@classes: resulting classes of attached devices
 *
 *	Note: Original code is ata_sff_softreset().
 */

static int bfin_softreset(struct ata_link *link, unsigned int *classes,
			  unsigned long deadline)
{
	struct ata_port *ap = link->ap;
	unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
	unsigned int devmask = 0, err_mask;
	u8 err;

	/* determine if device 0/1 are present */
	if (bfin_devchk(ap, 0))
		devmask |= (1 << 0);
	if (slave_possible && bfin_devchk(ap, 1))
		devmask |= (1 << 1);

	/* select device 0 again */
	bfin_dev_select(ap, 0);

	/* issue bus reset */
	err_mask = bfin_bus_softreset(ap, devmask);
	if (err_mask) {
		ata_port_err(ap, "SRST failed (err_mask=0x%x)\n",
				err_mask);
		return -EIO;
	}

	/* determine by signature whether we have ATA or ATAPI devices */
	classes[0] = ata_sff_dev_classify(&ap->link.device[0],
				devmask & (1 << 0), &err);
	if (slave_possible && err != 0x81)
		classes[1] = ata_sff_dev_classify(&ap->link.device[1],
					devmask & (1 << 1), &err);

	return 0;
}

/**
 *	bfin_bmdma_status - Read IDE DMA status
 *	@ap: Port associated with this ATA transaction.
 */

static unsigned char bfin_bmdma_status(struct ata_port *ap)
{
	unsigned char host_stat = 0;
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;

	if (ATAPI_GET_STATUS(base) & (MULTI_XFER_ON | ULTRA_XFER_ON))
		host_stat |= ATA_DMA_ACTIVE;
	if (ATAPI_GET_INT_STATUS(base) & ATAPI_DEV_INT)
		host_stat |= ATA_DMA_INTR;

	dev_dbg(ap->dev, "ATAPI: host_stat=0x%x\n", host_stat);

	return host_stat;
}

/**
 *	bfin_data_xfer - Transfer data by PIO
 *	@adev: device for this I/O
 *	@buf: data buffer
 *	@buflen: buffer length
 *	@write_data: read/write
 *
 *	Note: Original code is ata_sff_data_xfer().
 */

static unsigned int bfin_data_xfer(struct ata_device *dev, unsigned char *buf,
				   unsigned int buflen, int rw)
{
	struct ata_port *ap = dev->link->ap;
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;
	unsigned int words = buflen >> 1;
	unsigned short *buf16 = (u16 *)buf;

	/* Transfer multiple of 2 bytes */
	if (rw == READ)
		read_atapi_data(base, words, buf16);
	else
		write_atapi_data(base, words, buf16);

	/* Transfer trailing 1 byte, if any. */
	if (unlikely(buflen & 0x01)) {
		unsigned short align_buf[1] = { 0 };
		unsigned char *trailing_buf = buf + buflen - 1;

		if (rw == READ) {
			read_atapi_data(base, 1, align_buf);
			memcpy(trailing_buf, align_buf, 1);
		} else {
			memcpy(align_buf, trailing_buf, 1);
			write_atapi_data(base, 1, align_buf);
		}
		words++;
	}

	return words << 1;
}

/**
 *	bfin_irq_clear - Clear ATAPI interrupt.
 *	@ap: Port associated with this ATA transaction.
 *
 *	Note: Original code is ata_bmdma_irq_clear().
 */

static void bfin_irq_clear(struct ata_port *ap)
{
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;

	dev_dbg(ap->dev, "in atapi irq clear\n");
	ATAPI_SET_INT_STATUS(base, ATAPI_GET_INT_STATUS(base)|ATAPI_DEV_INT
		| MULTI_DONE_INT | UDMAIN_DONE_INT | UDMAOUT_DONE_INT
		| MULTI_TERM_INT | UDMAIN_TERM_INT | UDMAOUT_TERM_INT);
}

/**
 *	bfin_thaw - Thaw DMA controller port
 *	@ap: port to thaw
 *
 *	Note: Original code is ata_sff_thaw().
 */

void bfin_thaw(struct ata_port *ap)
{
	dev_dbg(ap->dev, "in atapi dma thaw\n");
	bfin_check_status(ap);
	ata_sff_irq_on(ap);
}

/**
 *	bfin_postreset - standard postreset callback
 *	@ap: the target ata_port
 *	@classes: classes of attached devices
 *
 *	Note: Original code is ata_sff_postreset().
 */

static void bfin_postreset(struct ata_link *link, unsigned int *classes)
{
	struct ata_port *ap = link->ap;
	void __iomem *base = (void __iomem *)ap->ioaddr.ctl_addr;

	/* re-enable interrupts */
	ata_sff_irq_on(ap);

	/* is double-select really necessary? */
	if (classes[0] != ATA_DEV_NONE)
		bfin_dev_select(ap, 1);
	if (classes[1] != ATA_DEV_NONE)
		bfin_dev_select(ap, 0);

	/* bail out if no device is present */
	if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) {
		return;
	}

	/* set up device control */
	write_atapi_register(base, ATA_REG_CTRL, ap->ctl);
}

static void bfin_port_stop(struct ata_port *ap)
{
	dev_dbg(ap->dev, "in atapi port stop\n");
	if (ap->udma_mask != 0 || ap->mwdma_mask != 0) {
		dma_free_coherent(ap->dev,
			BFIN_MAX_SG_SEGMENTS * sizeof(struct dma_desc_array),
			ap->bmdma_prd,
			ap->bmdma_prd_dma);

		free_dma(CH_ATAPI_RX);
		free_dma(CH_ATAPI_TX);
	}
}

static int bfin_port_start(struct ata_port *ap)
{
	dev_dbg(ap->dev, "in atapi port start\n");
	if (!(ap->udma_mask || ap->mwdma_mask))
		return 0;

	ap->bmdma_prd = dma_alloc_coherent(ap->dev,
				BFIN_MAX_SG_SEGMENTS * sizeof(struct dma_desc_array),
				&ap->bmdma_prd_dma,
				GFP_KERNEL);

	if (ap->bmdma_prd == NULL) {
		dev_info(ap->dev, "Unable to allocate DMA descriptor array.\n");
		goto out;
	}

	if (request_dma(CH_ATAPI_RX, "BFIN ATAPI RX DMA") >= 0) {
		if (request_dma(CH_ATAPI_TX,
			"BFIN ATAPI TX DMA") >= 0)
			return 0;

		free_dma(CH_ATAPI_RX);
		dma_free_coherent(ap->dev,
			BFIN_MAX_SG_SEGMENTS * sizeof(struct dma_desc_array),
			ap->bmdma_prd,
			ap->bmdma_prd_dma);
	}

out:
	ap->udma_mask = 0;
	ap->mwdma_mask = 0;
	dev_err(ap->dev, "Unable to request ATAPI DMA!"
		" Continue in PIO mode.\n");

	return 0;
}

static unsigned int bfin_ata_host_intr(struct ata_port *ap,
				   struct ata_queued_cmd *qc)
{
	struct ata_eh_info *ehi = &ap->link.eh_info;
	u8 status, host_stat = 0;

	VPRINTK("ata%u: protocol %d task_state %d\n",
		ap->print_id, qc->tf.protocol, ap->hsm_task_state);

	/* Check whether we are expecting interrupt in this state */
	switch (ap->hsm_task_state) {
	case HSM_ST_FIRST:
		/* Some pre-ATAPI-4 devices assert INTRQ
		 * at this state when ready to receive CDB.
		 */

		/* Check the ATA_DFLAG_CDB_INTR flag is enough here.
		 * The flag was turned on only for atapi devices.
		 * No need to check is_atapi_taskfile(&qc->tf) again.
		 */
		if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
			goto idle_irq;
		break;
	case HSM_ST_LAST:
		if (qc->tf.protocol == ATA_PROT_DMA ||
		    qc->tf.protocol == ATAPI_PROT_DMA) {
			/* check status of DMA engine */
			host_stat = ap->ops->bmdma_status(ap);
			VPRINTK("ata%u: host_stat 0x%X\n",
				ap->print_id, host_stat);

			/* if it's not our irq... */
			if (!(host_stat & ATA_DMA_INTR))
				goto idle_irq;

			/* before we do anything else, clear DMA-Start bit */
			ap->ops->bmdma_stop(qc);

			if (unlikely(host_stat & ATA_DMA_ERR)) {
				/* error when transferring data to/from memory */
				qc->err_mask |= AC_ERR_HOST_BUS;
				ap->hsm_task_state = HSM_ST_ERR;
			}
		}
		break;
	case HSM_ST:
		break;
	default:
		goto idle_irq;
	}

	/* check altstatus */
	status = ap->ops->sff_check_altstatus(ap);
	if (status & ATA_BUSY)
		goto busy_ata;

	/* check main status, clearing INTRQ */
	status = ap->ops->sff_check_status(ap);
	if (unlikely(status & ATA_BUSY))
		goto busy_ata;

	/* ack bmdma irq events */
	ap->ops->sff_irq_clear(ap);

	ata_sff_hsm_move(ap, qc, status, 0);

	if (unlikely(qc->err_mask) && (qc->tf.protocol == ATA_PROT_DMA ||
				       qc->tf.protocol == ATAPI_PROT_DMA))
		ata_ehi_push_desc(ehi, "BMDMA stat 0x%x", host_stat);

busy_ata:
	return 1;	/* irq handled */

idle_irq:
	ap->stats.idle_irq++;

#ifdef ATA_IRQ_TRAP
	if ((ap->stats.idle_irq % 1000) == 0) {
		ap->ops->irq_ack(ap, 0); /* debug trap */
		ata_port_warn(ap, "irq trap\n");
		return 1;
	}
#endif
	return 0;	/* irq not handled */
}

static irqreturn_t bfin_ata_interrupt(int irq, void *dev_instance)
{
	struct ata_host *host = dev_instance;
	unsigned int i;
	unsigned int handled = 0;
	unsigned long flags;

	/* TODO: make _irqsave conditional on x86 PCI IDE legacy mode */
	spin_lock_irqsave(&host->lock, flags);

	for (i = 0; i < host->n_ports; i++) {
		struct ata_port *ap = host->ports[i];
		struct ata_queued_cmd *qc;

		qc = ata_qc_from_tag(ap, ap->link.active_tag);
		if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING)))
			handled |= bfin_ata_host_intr(ap, qc);
	}

	spin_unlock_irqrestore(&host->lock, flags);

	return IRQ_RETVAL(handled);
}


static struct scsi_host_template bfin_sht = {
	ATA_BASE_SHT(DRV_NAME),
	.sg_tablesize		= BFIN_MAX_SG_SEGMENTS,
	.dma_boundary		= ATA_DMA_BOUNDARY,
};

static struct ata_port_operations bfin_pata_ops = {
	.inherits		= &ata_bmdma_port_ops,

	.set_piomode		= bfin_set_piomode,
	.set_dmamode		= bfin_set_dmamode,

	.sff_tf_load		= bfin_tf_load,
	.sff_tf_read		= bfin_tf_read,
	.sff_exec_command	= bfin_exec_command,
	.sff_check_status	= bfin_check_status,
	.sff_check_altstatus	= bfin_check_altstatus,
	.sff_dev_select		= bfin_dev_select,
	.sff_set_devctl		= bfin_set_devctl,

	.bmdma_setup		= bfin_bmdma_setup,
	.bmdma_start		= bfin_bmdma_start,
	.bmdma_stop		= bfin_bmdma_stop,
	.bmdma_status		= bfin_bmdma_status,
	.sff_data_xfer		= bfin_data_xfer,

	.qc_prep		= ata_noop_qc_prep,

	.thaw			= bfin_thaw,
	.softreset		= bfin_softreset,
	.postreset		= bfin_postreset,

	.sff_irq_clear		= bfin_irq_clear,

	.port_start		= bfin_port_start,
	.port_stop		= bfin_port_stop,
};

static struct ata_port_info bfin_port_info[] = {
	{
		.flags		= ATA_FLAG_SLAVE_POSS,
		.pio_mask	= ATA_PIO4,
		.mwdma_mask	= 0,
		.udma_mask	= 0,
		.port_ops	= &bfin_pata_ops,
	},
};

/**
 *	bfin_reset_controller - initialize BF54x ATAPI controller.
 */

static int bfin_reset_controller(struct ata_host *host)
{
	void __iomem *base = (void __iomem *)host->ports[0]->ioaddr.ctl_addr;
	int count;
	unsigned short status;

	/* Disable all ATAPI interrupts */
	ATAPI_SET_INT_MASK(base, 0);
	SSYNC();

	/* Assert the RESET signal 25us*/
	ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base) | DEV_RST);
	udelay(30);

	/* Negate the RESET signal for 2ms*/
	ATAPI_SET_CONTROL(base, ATAPI_GET_CONTROL(base) & ~DEV_RST);
	msleep(2);

	/* Wait on Busy flag to clear */
	count = 10000000;
	do {
		status = read_atapi_register(base, ATA_REG_STATUS);
	} while (--count && (status & ATA_BUSY));

	/* Enable only ATAPI Device interrupt */
	ATAPI_SET_INT_MASK(base, 1);
	SSYNC();

	return (!count);
}

/**
 *	atapi_io_port - define atapi peripheral port pins.
 */
static unsigned short atapi_io_port[] = {
	P_ATAPI_RESET,
	P_ATAPI_DIOR,
	P_ATAPI_DIOW,
	P_ATAPI_CS0,
	P_ATAPI_CS1,
	P_ATAPI_DMACK,
	P_ATAPI_DMARQ,
	P_ATAPI_INTRQ,
	P_ATAPI_IORDY,
	P_ATAPI_D0A,
	P_ATAPI_D1A,
	P_ATAPI_D2A,
	P_ATAPI_D3A,
	P_ATAPI_D4A,
	P_ATAPI_D5A,
	P_ATAPI_D6A,
	P_ATAPI_D7A,
	P_ATAPI_D8A,
	P_ATAPI_D9A,
	P_ATAPI_D10A,
	P_ATAPI_D11A,
	P_ATAPI_D12A,
	P_ATAPI_D13A,
	P_ATAPI_D14A,
	P_ATAPI_D15A,
	P_ATAPI_A0A,
	P_ATAPI_A1A,
	P_ATAPI_A2A,
	0
};

/**
 *	bfin_atapi_probe	-	attach a bfin atapi interface
 *	@pdev: platform device
 *
 *	Register a bfin atapi interface.
 *
 *
 *	Platform devices are expected to contain 2 resources per port:
 *
 *		- I/O Base (IORESOURCE_IO)
 *		- IRQ	   (IORESOURCE_IRQ)
 *
 */
static int __devinit bfin_atapi_probe(struct platform_device *pdev)
{
	int board_idx = 0;
	struct resource *res;
	struct ata_host *host;
	unsigned int fsclk = get_sclk();
	int udma_mode = 5;
	const struct ata_port_info *ppi[] =
		{ &bfin_port_info[board_idx], NULL };

	/*
	 * Simple resource validation ..
	 */
	if (unlikely(pdev->num_resources != 2)) {
		dev_err(&pdev->dev, "invalid number of resources\n");
		return -EINVAL;
	}

	/*
	 * Get the register base first
	 */
	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	if (res == NULL)
		return -EINVAL;

	while (bfin_port_info[board_idx].udma_mask > 0 &&
			udma_fsclk[udma_mode] > fsclk) {
		udma_mode--;
		bfin_port_info[board_idx].udma_mask >>= 1;
	}

	/*
	 * Now that that's out of the way, wire up the port..
	 */
	host = ata_host_alloc_pinfo(&pdev->dev, ppi, 1);
	if (!host)
		return -ENOMEM;

	host->ports[0]->ioaddr.ctl_addr = (void *)res->start;

	if (peripheral_request_list(atapi_io_port, "atapi-io-port")) {
		dev_err(&pdev->dev, "Requesting Peripherals failed\n");
		return -EFAULT;
	}

	if (bfin_reset_controller(host)) {
		peripheral_free_list(atapi_io_port);
		dev_err(&pdev->dev, "Fail to reset ATAPI device\n");
		return -EFAULT;
	}

	if (ata_host_activate(host, platform_get_irq(pdev, 0),
		bfin_ata_interrupt, IRQF_SHARED, &bfin_sht) != 0) {
		peripheral_free_list(atapi_io_port);
		dev_err(&pdev->dev, "Fail to attach ATAPI device\n");
		return -ENODEV;
	}

	dev_set_drvdata(&pdev->dev, host);

	return 0;
}

/**
 *	bfin_atapi_remove	-	unplug a bfin atapi interface
 *	@pdev: platform device
 *
 *	A bfin atapi device has been unplugged. Perform the needed
 *	cleanup. Also called on module unload for any active devices.
 */
static int __devexit bfin_atapi_remove(struct platform_device *pdev)
{
	struct device *dev = &pdev->dev;
	struct ata_host *host = dev_get_drvdata(dev);

	ata_host_detach(host);
	dev_set_drvdata(&pdev->dev, NULL);

	peripheral_free_list(atapi_io_port);

	return 0;
}

#ifdef CONFIG_PM
static int bfin_atapi_suspend(struct platform_device *pdev, pm_message_t state)
{
	struct ata_host *host = dev_get_drvdata(&pdev->dev);
	if (host)
		return ata_host_suspend(host, state);
	else
		return 0;
}

static int bfin_atapi_resume(struct platform_device *pdev)
{
	struct ata_host *host = dev_get_drvdata(&pdev->dev);
	int ret;

	if (host) {
		ret = bfin_reset_controller(host);
		if (ret) {
			printk(KERN_ERR DRV_NAME ": Error during HW init\n");
			return ret;
		}
		ata_host_resume(host);
	}

	return 0;
}
#else
#define bfin_atapi_suspend NULL
#define bfin_atapi_resume NULL
#endif

static struct platform_driver bfin_atapi_driver = {
	.probe			= bfin_atapi_probe,
	.remove			= __devexit_p(bfin_atapi_remove),
	.suspend		= bfin_atapi_suspend,
	.resume			= bfin_atapi_resume,
	.driver = {
		.name		= DRV_NAME,
		.owner		= THIS_MODULE,
	},
};

#define ATAPI_MODE_SIZE		10
static char bfin_atapi_mode[ATAPI_MODE_SIZE];

static int __init bfin_atapi_init(void)
{
	pr_info("register bfin atapi driver\n");

	switch(bfin_atapi_mode[0]) {
	case 'p':
	case 'P':
		break;
	case 'm':
	case 'M':
		bfin_port_info[0].mwdma_mask = ATA_MWDMA2;
		break;
	default:
		bfin_port_info[0].udma_mask = ATA_UDMA5;
	};

	return platform_driver_register(&bfin_atapi_driver);
}

static void __exit bfin_atapi_exit(void)
{
	platform_driver_unregister(&bfin_atapi_driver);
}

module_init(bfin_atapi_init);
module_exit(bfin_atapi_exit);
/*
 * ATAPI mode:
 * pio/PIO
 * udma/UDMA (default)
 * mwdma/MWDMA
 */
module_param_string(bfin_atapi_mode, bfin_atapi_mode, ATAPI_MODE_SIZE, 0);

MODULE_AUTHOR("Sonic Zhang <sonic.zhang@analog.com>");
MODULE_DESCRIPTION("PATA driver for blackfin 54x ATAPI controller");
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);
MODULE_ALIAS("platform:" DRV_NAME);