aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/scsi/sata_uli.c
blob: eb202a73bc0edb9b79a972cd092ac0dc606c21be (plain) (blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
/*
 *  sata_uli.c - ULi Electronics SATA
 *
 *  The contents of this file are subject to the Open
 *  Software License version 1.1 that can be found at
 *  http://www.opensource.org/licenses/osl-1.1.txt and is included herein
 *  by reference.
 *
 *  Alternatively, the contents of this file may be used under the terms
 *  of the GNU General Public License version 2 (the "GPL") as distributed
 *  in the kernel source COPYING file, in which case the provisions of
 *  the GPL are applicable instead of the above.  If you wish to allow
 *  the use of your version of this file only under the terms of the
 *  GPL and not to allow others to use your version of this file under
 *  the OSL, indicate your decision by deleting the provisions above and
 *  replace them with the notice and other provisions required by the GPL.
 *  If you do not delete the provisions above, a recipient may use your
 *  version of this file under either the OSL or the GPL.
 *
 */

#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>

#define DRV_NAME	"sata_uli"
#define DRV_VERSION	"0.5"

enum {
	uli_5289		= 0,
	uli_5287		= 1,
	uli_5281		= 2,

	/* PCI configuration registers */
	ULI5287_BASE		= 0x90, /* sata0 phy SCR registers */
	ULI5287_OFFS		= 0x10, /* offset from sata0->sata1 phy regs */
	ULI5281_BASE		= 0x60, /* sata0 phy SCR  registers */
	ULI5281_OFFS		= 0x60, /* offset from sata0->sata1 phy regs */
};

static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);

static struct pci_device_id uli_pci_tbl[] = {
	{ PCI_VENDOR_ID_AL, 0x5289, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5289 },
	{ PCI_VENDOR_ID_AL, 0x5287, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5287 },
	{ PCI_VENDOR_ID_AL, 0x5281, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5281 },
	{ }	/* terminate list */
};


static struct pci_driver uli_pci_driver = {
	.name			= DRV_NAME,
	.id_table		= uli_pci_tbl,
	.probe			= uli_init_one,
	.remove			= ata_pci_remove_one,
};

static Scsi_Host_Template uli_sht = {
	.module			= THIS_MODULE,
	.name			= DRV_NAME,
	.ioctl			= ata_scsi_ioctl,
	.queuecommand		= ata_scsi_queuecmd,
	.eh_strategy_handler	= ata_scsi_error,
	.can_queue		= ATA_DEF_QUEUE,
	.this_id		= ATA_SHT_THIS_ID,
	.sg_tablesize		= LIBATA_MAX_PRD,
	.max_sectors		= ATA_MAX_SECTORS,
	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
	.emulated		= ATA_SHT_EMULATED,
	.use_clustering		= ATA_SHT_USE_CLUSTERING,
	.proc_name		= DRV_NAME,
	.dma_boundary		= ATA_DMA_BOUNDARY,
	.slave_configure	= ata_scsi_slave_config,
	.bios_param		= ata_std_bios_param,
	.ordered_flush		= 1,
};

static struct ata_port_operations uli_ops = {
	.port_disable		= ata_port_disable,

	.tf_load		= ata_tf_load,
	.tf_read		= ata_tf_read,
	.check_status		= ata_check_status,
	.exec_command		= ata_exec_command,
	.dev_select		= ata_std_dev_select,

	.phy_reset		= sata_phy_reset,

	.bmdma_setup            = ata_bmdma_setup,
	.bmdma_start            = ata_bmdma_start,
	.bmdma_stop		= ata_bmdma_stop,
	.bmdma_status		= ata_bmdma_status,
	.qc_prep		= ata_qc_prep,
	.qc_issue		= ata_qc_issue_prot,

	.eng_timeout		= ata_eng_timeout,

	.irq_handler		= ata_interrupt,
	.irq_clear		= ata_bmdma_irq_clear,

	.scr_read		= uli_scr_read,
	.scr_write		= uli_scr_write,

	.port_start		= ata_port_start,
	.port_stop		= ata_port_stop,
	.host_stop		= ata_host_stop,
};

static struct ata_port_info uli_port_info = {
	.sht            = &uli_sht,
	.host_flags     = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
			  ATA_FLAG_NO_LEGACY,
	.pio_mask       = 0x03,		//support pio mode 4 (FIXME)
	.udma_mask      = 0x7f,		//support udma mode 6
	.port_ops       = &uli_ops,
};


MODULE_AUTHOR("Peer Chen");
MODULE_DESCRIPTION("low-level driver for ULi Electronics SATA controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, uli_pci_tbl);
MODULE_VERSION(DRV_VERSION);

static unsigned int get_scr_cfg_addr(struct ata_port *ap, unsigned int sc_reg)
{
	return ap->ioaddr.scr_addr + (4 * sc_reg);
}

static u32 uli_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
{
	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
	unsigned int cfg_addr = get_scr_cfg_addr(ap, sc_reg);
	u32 val;

	pci_read_config_dword(pdev, cfg_addr, &val);
	return val;
}

static void uli_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
{
	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
	unsigned int cfg_addr = get_scr_cfg_addr(ap, scr);

	pci_write_config_dword(pdev, cfg_addr, val);
}

static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg)
{
	if (sc_reg > SCR_CONTROL)
		return 0xffffffffU;

	return uli_scr_cfg_read(ap, sc_reg);
}

static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
{
	if (sc_reg > SCR_CONTROL)	//SCR_CONTROL=2, SCR_ERROR=1, SCR_STATUS=0
		return;

	uli_scr_cfg_write(ap, sc_reg, val);
}

/* move to PCI layer, integrate w/ MSI stuff */
static void pci_enable_intx(struct pci_dev *pdev)
{
	u16 pci_command;

	pci_read_config_word(pdev, PCI_COMMAND, &pci_command);
	if (pci_command & PCI_COMMAND_INTX_DISABLE) {
		pci_command &= ~PCI_COMMAND_INTX_DISABLE;
		pci_write_config_word(pdev, PCI_COMMAND, pci_command);
	}
}

static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
	struct ata_probe_ent *probe_ent;
	struct ata_port_info *ppi;
	int rc;
	unsigned int board_idx = (unsigned int) ent->driver_data;
	int pci_dev_busy = 0;

	rc = pci_enable_device(pdev);
	if (rc)
		return rc;

	rc = pci_request_regions(pdev, DRV_NAME);
	if (rc) {
		pci_dev_busy = 1;
		goto err_out;
	}

	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
	if (rc)
		goto err_out_regions;
	rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
	if (rc)
		goto err_out_regions;

	ppi = &uli_port_info;
	probe_ent = ata_pci_init_native_mode(pdev, &ppi);
	if (!probe_ent) {
		rc = -ENOMEM;
		goto err_out_regions;
	}

	switch (board_idx) {
	case uli_5287:
		probe_ent->port[0].scr_addr = ULI5287_BASE;
		probe_ent->port[1].scr_addr = ULI5287_BASE + ULI5287_OFFS;
       		probe_ent->n_ports = 4;

       		probe_ent->port[2].cmd_addr = pci_resource_start(pdev, 0) + 8;
		probe_ent->port[2].altstatus_addr =
		probe_ent->port[2].ctl_addr =
			(pci_resource_start(pdev, 1) | ATA_PCI_CTL_OFS) + 4;
		probe_ent->port[2].bmdma_addr = pci_resource_start(pdev, 4) + 16;
		probe_ent->port[2].scr_addr = ULI5287_BASE + ULI5287_OFFS*4;

		probe_ent->port[3].cmd_addr = pci_resource_start(pdev, 2) + 8;
		probe_ent->port[3].altstatus_addr =
		probe_ent->port[3].ctl_addr =
			(pci_resource_start(pdev, 3) | ATA_PCI_CTL_OFS) + 4;
		probe_ent->port[3].bmdma_addr = pci_resource_start(pdev, 4) + 24;
		probe_ent->port[3].scr_addr = ULI5287_BASE + ULI5287_OFFS*5;

		ata_std_ports(&probe_ent->port[2]);
		ata_std_ports(&probe_ent->port[3]);
		break;

	case uli_5289:
		probe_ent->port[0].scr_addr = ULI5287_BASE;
		probe_ent->port[1].scr_addr = ULI5287_BASE + ULI5287_OFFS;
		break;

	case uli_5281:
		probe_ent->port[0].scr_addr = ULI5281_BASE;
		probe_ent->port[1].scr_addr = ULI5281_BASE + ULI5281_OFFS;
		break;

	default:
		BUG();
		break;
	}

	pci_set_master(pdev);
	pci_enable_intx(pdev);

	/* FIXME: check ata_device_add return value */
	ata_device_add(probe_ent);
	kfree(probe_ent);

	return 0;

err_out_regions:
	pci_release_regions(pdev);

err_out:
	if (!pci_dev_busy)
		pci_disable_device(pdev);
	return rc;

}

static int __init uli_init(void)
{
	return pci_module_init(&uli_pci_driver);
}

static void __exit uli_exit(void)
{
	pci_unregister_driver(&uli_pci_driver);
}


module_init(uli_init);
module_exit(uli_exit);