1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
|
#ifndef SPI_ADIS16203_H_
#define SPI_ADIS16203_H_
#define ADIS16203_STARTUP_DELAY 220 /* ms */
/* Flash memory write count */
#define ADIS16203_FLASH_CNT 0x00
/* Output, power supply */
#define ADIS16203_SUPPLY_OUT 0x02
/* Output, auxiliary ADC input */
#define ADIS16203_AUX_ADC 0x08
/* Output, temperature */
#define ADIS16203_TEMP_OUT 0x0A
/* Output, x-axis inclination */
#define ADIS16203_XINCL_OUT 0x0C
/* Output, y-axis inclination */
#define ADIS16203_YINCL_OUT 0x0E
/* Incline null calibration */
#define ADIS16203_INCL_NULL 0x18
/* Alarm 1 amplitude threshold */
#define ADIS16203_ALM_MAG1 0x20
/* Alarm 2 amplitude threshold */
#define ADIS16203_ALM_MAG2 0x22
/* Alarm 1, sample period */
#define ADIS16203_ALM_SMPL1 0x24
/* Alarm 2, sample period */
#define ADIS16203_ALM_SMPL2 0x26
/* Alarm control */
#define ADIS16203_ALM_CTRL 0x28
/* Auxiliary DAC data */
#define ADIS16203_AUX_DAC 0x30
/* General-purpose digital input/output control */
#define ADIS16203_GPIO_CTRL 0x32
/* Miscellaneous control */
#define ADIS16203_MSC_CTRL 0x34
/* Internal sample period (rate) control */
#define ADIS16203_SMPL_PRD 0x36
/* Operation, filter configuration */
#define ADIS16203_AVG_CNT 0x38
/* Operation, sleep mode control */
#define ADIS16203_SLP_CNT 0x3A
/* Diagnostics, system status register */
#define ADIS16203_DIAG_STAT 0x3C
/* Operation, system command register */
#define ADIS16203_GLOB_CMD 0x3E
/* MSC_CTRL */
/* Self-test at power-on: 1 = disabled, 0 = enabled */
#define ADIS16203_MSC_CTRL_PWRUP_SELF_TEST BIT(10)
/* Reverses rotation of both inclination outputs */
#define ADIS16203_MSC_CTRL_REVERSE_ROT_EN BIT(9)
/* Self-test enable */
#define ADIS16203_MSC_CTRL_SELF_TEST_EN BIT(8)
/* Data-ready enable: 1 = enabled, 0 = disabled */
#define ADIS16203_MSC_CTRL_DATA_RDY_EN BIT(2)
/* Data-ready polarity: 1 = active high, 0 = active low */
#define ADIS16203_MSC_CTRL_ACTIVE_HIGH BIT(1)
/* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
#define ADIS16203_MSC_CTRL_DATA_RDY_DIO1 BIT(0)
/* DIAG_STAT */
/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
#define ADIS16203_DIAG_STAT_ALARM2 BIT(9)
/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
#define ADIS16203_DIAG_STAT_ALARM1 BIT(8)
/* Self-test diagnostic error flag */
#define ADIS16203_DIAG_STAT_SELFTEST_FAIL_BIT 5
/* SPI communications failure */
#define ADIS16203_DIAG_STAT_SPI_FAIL_BIT 3
/* Flash update failure */
#define ADIS16203_DIAG_STAT_FLASH_UPT_BIT 2
/* Power supply above 3.625 V */
#define ADIS16203_DIAG_STAT_POWER_HIGH_BIT 1
/* Power supply below 3.15 V */
#define ADIS16203_DIAG_STAT_POWER_LOW_BIT 0
/* GLOB_CMD */
#define ADIS16203_GLOB_CMD_SW_RESET BIT(7)
#define ADIS16203_GLOB_CMD_CLEAR_STAT BIT(4)
#define ADIS16203_GLOB_CMD_FACTORY_CAL BIT(1)
#define ADIS16203_ERROR_ACTIVE BIT(14)
enum adis16203_scan {
ADIS16203_SCAN_INCLI_X,
ADIS16203_SCAN_INCLI_Y,
ADIS16203_SCAN_SUPPLY,
ADIS16203_SCAN_AUX_ADC,
ADIS16203_SCAN_TEMP,
};
#endif /* SPI_ADIS16203_H_ */
|