1 files changed, 0 insertions, 112 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt
deleted file mode 100644
index 1c94a57a661e..000000000000
--- a/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt
+++ /dev/null
@@ -1,112 +0,0 @@
-Marvell ICU Interrupt Controller
---------------------------------
-
-The Marvell ICU (Interrupt Consolidation Unit) controller is
-responsible for collecting all wired-interrupt sources in the CP and
-communicating them to the GIC in the AP, the unit translates interrupt
-requests on input wires to MSG memory mapped transactions to the GIC.
-These messages will access a different GIC memory area depending on
-their type (NSR, SR, SEI, REI, etc).
-
-Required properties:
-
-- compatible: Should be "marvell,cp110-icu"
-
-- reg: Should contain ICU registers location and length.
-
-Subnodes: Each group of interrupt is declared as a subnode of the ICU,
-with their own compatible.
-
-Required properties for the icu_nsr/icu_sei subnodes:
-
-- compatible: Should be one of:
-              * "marvell,cp110-icu-nsr"
-	      * "marvell,cp110-icu-sr"
-	      * "marvell,cp110-icu-sei"
-	      * "marvell,cp110-icu-rei"
-
-- #interrupt-cells: Specifies the number of cells needed to encode an
-  interrupt source. The value shall be 2.
-
-  The 1st cell is the index of the interrupt in the ICU unit.
-
-  The 2nd cell is the type of the interrupt. See arm,gic.txt for
-  details.
-
-- interrupt-controller: Identifies the node as an interrupt
-  controller.
-
-- msi-parent: Should point to the GICP controller, the GIC extension
-  that allows to trigger interrupts using MSG memory mapped
-  transactions.
-
-Note: each 'interrupts' property referring to any 'icu_xxx' node shall
-      have a different number within [0:206].
-
-Example:
-
-icu: interrupt-controller@1e0000 {
-	compatible = "marvell,cp110-icu";
-	reg = <0x1e0000 0x440>;
-
-	CP110_LABEL(icu_nsr): interrupt-controller@10 {
-		compatible = "marvell,cp110-icu-nsr";
-		reg = <0x10 0x20>;
-		#interrupt-cells = <2>;
-		interrupt-controller;
-		msi-parent = <&gicp>;
-	};
-
-	CP110_LABEL(icu_sei): interrupt-controller@50 {
-		compatible = "marvell,cp110-icu-sei";
-		reg = <0x50 0x10>;
-		#interrupt-cells = <2>;
-		interrupt-controller;
-		msi-parent = <&sei>;
-	};
-};
-
-node1 {
-	interrupt-parent = <&icu_nsr>;
-	interrupts = <106 IRQ_TYPE_LEVEL_HIGH>;
-};
-
-node2 {
-	interrupt-parent = <&icu_sei>;
-	interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
-};
-
-/* Would not work with the above nodes */
-node3 {
-	interrupt-parent = <&icu_nsr>;
-	interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
-};
-
-The legacy bindings were different in this way:
-
-- #interrupt-cells: The value was 3.
-	The 1st cell was the group type of the ICU interrupt. Possible
-	group types were:
-	ICU_GRP_NSR (0x0) : Shared peripheral interrupt, non-secure
-	ICU_GRP_SR  (0x1) : Shared peripheral interrupt, secure
-	ICU_GRP_SEI (0x4) : System error interrupt
-	ICU_GRP_REI (0x5) : RAM error interrupt
-	The 2nd cell was the index of the interrupt in the ICU unit.
-	The 3rd cell was the type of the interrupt. See arm,gic.txt for
-	details.
-
-Example:
-
-icu: interrupt-controller@1e0000 {
-	compatible = "marvell,cp110-icu";
-	reg = <0x1e0000 0x440>;
-
-	#interrupt-cells = <3>;
-	interrupt-controller;
-	msi-parent = <&gicp>;
-};
-
-node1 {
-	interrupt-parent = <&icu>;
-	interrupts = <ICU_GRP_NSR 106 IRQ_TYPE_LEVEL_HIGH>;
-};