diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci/mvebu-pci.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pci/mvebu-pci.txt | 310 |
1 files changed, 0 insertions, 310 deletions
diff --git a/Documentation/devicetree/bindings/pci/mvebu-pci.txt b/Documentation/devicetree/bindings/pci/mvebu-pci.txt deleted file mode 100644 index 6d022a9d36ee..000000000000 --- a/Documentation/devicetree/bindings/pci/mvebu-pci.txt +++ /dev/null @@ -1,310 +0,0 @@ -* Marvell EBU PCIe interfaces - -Mandatory properties: - -- compatible: one of the following values: - marvell,armada-370-pcie - marvell,armada-xp-pcie - marvell,dove-pcie - marvell,kirkwood-pcie -- #address-cells, set to <3> -- #size-cells, set to <2> -- #interrupt-cells, set to <1> -- bus-range: PCI bus numbers covered -- device_type, set to "pci" -- ranges: ranges describing the MMIO registers to control the PCIe - interfaces, and ranges describing the MBus windows needed to access - the memory and I/O regions of each PCIe interface. -- msi-parent: Link to the hardware entity that serves as the Message - Signaled Interrupt controller for this PCI controller. - -The ranges describing the MMIO registers have the following layout: - - 0x82000000 0 r MBUS_ID(0xf0, 0x01) r 0 s - -where: - - * r is a 32-bits value that gives the offset of the MMIO - registers of this PCIe interface, from the base of the internal - registers. - - * s is a 32-bits value that give the size of this MMIO - registers area. This range entry translates the '0x82000000 0 r' PCI - address into the 'MBUS_ID(0xf0, 0x01) r' CPU address, which is part - of the internal register window (as identified by MBUS_ID(0xf0, - 0x01)). - -The ranges describing the MBus windows have the following layout: - - 0x8t000000 s 0 MBUS_ID(w, a) 0 1 0 - -where: - - * t is the type of the MBus window (as defined by the standard PCI DT - bindings), 1 for I/O and 2 for memory. - - * s is the PCI slot that corresponds to this PCIe interface - - * w is the 'target ID' value for the MBus window - - * a the 'attribute' value for the MBus window. - -Since the location and size of the different MBus windows is not fixed in -hardware, and only determined in runtime, those ranges cover the full first -4 GB of the physical address space, and do not translate into a valid CPU -address. - -In addition, the device tree node must have sub-nodes describing each -PCIe interface, having the following mandatory properties: - -- reg: used only for interrupt mapping, so only the first four bytes - are used to refer to the correct bus number and device number. -- assigned-addresses: reference to the MMIO registers used to control - this PCIe interface. -- clocks: the clock associated to this PCIe interface -- marvell,pcie-port: the physical PCIe port number -- status: either "disabled" or "okay" -- device_type, set to "pci" -- #address-cells, set to <3> -- #size-cells, set to <2> -- #interrupt-cells, set to <1> -- ranges, translating the MBus windows ranges of the parent node into - standard PCI addresses. -- interrupt-map-mask and interrupt-map, standard PCI properties to - define the mapping of the PCIe interface to interrupt numbers. - -and the following optional properties: -- marvell,pcie-lane: the physical PCIe lane number, for ports having - multiple lanes. If this property is not found, we assume that the - value is 0. -- num-lanes: number of SerDes PCIe lanes for this link (1 or 4) -- reset-gpios: optional GPIO to PERST# -- reset-delay-us: delay in us to wait after reset de-assertion, if not - specified will default to 100ms, as required by the PCIe specification. -- interrupt-names: list of interrupt names, supported are: - - "intx" - interrupt line triggered by one of the legacy interrupt -- interrupts or interrupts-extended: List of the interrupt sources which - corresponding to the "interrupt-names". If non-empty then also additional - 'interrupt-controller' subnode must be defined. - -Example: - -pcie-controller { - compatible = "marvell,armada-xp-pcie"; - device_type = "pci"; - - #address-cells = <3>; - #size-cells = <2>; - - bus-range = <0x00 0xff>; - msi-parent = <&mpic>; - - ranges = - <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */ - 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */ - 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */ - 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */ - 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */ - 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */ - 0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000 /* Port 3.0 registers */ - 0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000 /* Port 1.1 registers */ - 0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000 /* Port 1.2 registers */ - 0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000 /* Port 1.3 registers */ - 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ - 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */ - 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */ - 0x81000000 0x2 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 0.1 IO */ - 0x82000000 0x3 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 0.2 MEM */ - 0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */ - 0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */ - 0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */ - - 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ - 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */ - 0x82000000 0x6 0 MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */ - 0x81000000 0x6 0 MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO */ - 0x82000000 0x7 0 MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */ - 0x81000000 0x7 0 MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO */ - 0x82000000 0x8 0 MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */ - 0x81000000 0x8 0 MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO */ - - 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */ - 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */ - - 0x82000000 0xa 0 MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */ - 0x81000000 0xa 0 MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO */>; - - pcie@1,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; - reg = <0x0800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 - 0x81000000 0 0 0x81000000 0x1 0 1 0>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 58>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <0>; - num-lanes = <1>; - /* low-active PERST# reset on GPIO 25 */ - reset-gpios = <&gpio0 25 1>; - /* wait 20ms for device settle after reset deassertion */ - reset-delay-us = <20000>; - clocks = <&gateclk 5>; - }; - - pcie@2,0 { - device_type = "pci"; - assigned-addresses = <0x82001000 0 0x44000 0 0x2000>; - reg = <0x1000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 - 0x81000000 0 0 0x81000000 0x2 0 1 0>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 59>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <1>; - num-lanes = <1>; - clocks = <&gateclk 6>; - }; - - pcie@3,0 { - device_type = "pci"; - assigned-addresses = <0x82001800 0 0x48000 0 0x2000>; - reg = <0x1800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 - 0x81000000 0 0 0x81000000 0x3 0 1 0>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 60>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <2>; - num-lanes = <1>; - clocks = <&gateclk 7>; - }; - - pcie@4,0 { - device_type = "pci"; - assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>; - reg = <0x2000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0 - 0x81000000 0 0 0x81000000 0x4 0 1 0>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 61>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <3>; - num-lanes = <1>; - clocks = <&gateclk 8>; - }; - - pcie@5,0 { - device_type = "pci"; - assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; - reg = <0x2800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0 - 0x81000000 0 0 0x81000000 0x5 0 1 0>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 62>; - marvell,pcie-port = <1>; - marvell,pcie-lane = <0>; - num-lanes = <1>; - clocks = <&gateclk 9>; - }; - - pcie@6,0 { - device_type = "pci"; - assigned-addresses = <0x82003000 0 0x84000 0 0x2000>; - reg = <0x3000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0 - 0x81000000 0 0 0x81000000 0x6 0 1 0>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 63>; - marvell,pcie-port = <1>; - marvell,pcie-lane = <1>; - num-lanes = <1>; - clocks = <&gateclk 10>; - }; - - pcie@7,0 { - device_type = "pci"; - assigned-addresses = <0x82003800 0 0x88000 0 0x2000>; - reg = <0x3800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0 - 0x81000000 0 0 0x81000000 0x7 0 1 0>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 64>; - marvell,pcie-port = <1>; - marvell,pcie-lane = <2>; - num-lanes = <1>; - clocks = <&gateclk 11>; - }; - - pcie@8,0 { - device_type = "pci"; - assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>; - reg = <0x4000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0 - 0x81000000 0 0 0x81000000 0x8 0 1 0>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 65>; - marvell,pcie-port = <1>; - marvell,pcie-lane = <3>; - num-lanes = <1>; - clocks = <&gateclk 12>; - }; - - pcie@9,0 { - device_type = "pci"; - assigned-addresses = <0x82004800 0 0x42000 0 0x2000>; - reg = <0x4800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0 - 0x81000000 0 0 0x81000000 0x9 0 1 0>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 99>; - marvell,pcie-port = <2>; - marvell,pcie-lane = <0>; - num-lanes = <1>; - clocks = <&gateclk 26>; - }; - - pcie@a,0 { - device_type = "pci"; - assigned-addresses = <0x82005000 0 0x82000 0 0x2000>; - reg = <0x5000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0 - 0x81000000 0 0 0x81000000 0xa 0 1 0>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 103>; - marvell,pcie-port = <3>; - marvell,pcie-lane = <0>; - num-lanes = <1>; - clocks = <&gateclk 27>; - }; -}; |