| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On the HiSilicon accelerators drivers, the PF/VFs driver can send messages
to the VFs/PF by writing hardware registers, and the VFs/PF driver receives
messages from the PF/VFs by reading hardware registers. To support this
feature, a new version id is added, different communication mechanism are
used based on different version id.
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The error detection of the data aggregation feature is separated from
the compression/decompression feature. This patch enables the error
detection and reporting of the data aggregation feature. When an
unrecoverable error occurs in the algorithm core, the device reports
the error to the driver, and the driver will reset the device.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If an error indicating that the device needs to be reset is reported,
disable the error reporting before device reset is complete,
enable the error reporting after the reset is complete to prevent
the same error from being reported repeatedly.
Fixes: eaebf4c3b103 ("crypto: hisilicon - Unify hardware error init/uninit into QM")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Query the capability register status of accelerator devices
(SEC, HPRE and ZIP) through the debugfs interface, for example:
cat cap_regs. The purpose is to improve the robustness and
locability of hardware devices and drivers.
Signed-off-by: Qi Tao <taoqi10@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Ensure that the inline function contains no more than 10 lines.
move q_num_set() from hisi_acc_qm.h to qm.c.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Before the device is enabled again, the device may still
store the previously processed data. If an error occurs in
the previous task, the device may fail to be enabled again.
Therefore, before enabling device, reset the device to restore
the initial state.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The offset of SEC_CORE_ENABLE_BITMAP should be 0 instead of 32,
it cause a kasan shift-out-bounds warning, fix it.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Some information showed by the dump function is invalid. Mask
the unnecessary information from the dump file.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
There is a scenario where the file directory is created but the
file memory is not set. In this case, if a user accesses the
file, an error occurs.
So during the creation process of debugfs, memory should be
allocated first before creating the directory. In the release
process, the directory should be deleted first before releasing
the memory to avoid the situation where the memory does not
exist when accessing the directory.
In addition, the directory released by the debugfs is a global
variable. When the debugfs of an accelerator fails to be
initialized, releasing the directory of the global variable
affects the debugfs initialization of other accelerators.
The debugfs root directory released by debugfs init should be a
member of qm, not a global variable.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When CONFIG_PCI_IOV is disabled, the SRIOV configuration
function is not required. An error occurs if this function is
incorrectly called.
Consistent with other modules, add the condition for
configuring the sriov function of sec_pci_driver.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
As the sec DFX function is enhanced, some RAS registers are added
to the original DFX registers to enhance the DFX positioning function.
Signed-off-by: Qi Tao <taoqi10@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Switch to raw_smp_processor_id() to prevent a number of
warnings from kernel debugging. We do not care about
preemption here, as the CPU number is only used as a
poor mans load balancing or device selection. If preemption
happens during an encrypt/decrypt operation a small performance
hit will occur but everything will continue to work, so just
ignore it. This commit is similar to e7a9b05ca4
("crypto: cavium - Fix smp_processor_id() warnings").
[ 7538.874350] BUG: using smp_processor_id() in preemptible [00000000] code: af_alg06/8438
[ 7538.874368] caller is debug_smp_processor_id+0x1c/0x28
[ 7538.874373] CPU: 50 PID: 8438 Comm: af_alg06 Kdump: loaded Not tainted 5.10.0.pc+ #18
[ 7538.874377] Call trace:
[ 7538.874387] dump_backtrace+0x0/0x210
[ 7538.874389] show_stack+0x2c/0x38
[ 7538.874392] dump_stack+0x110/0x164
[ 7538.874394] check_preemption_disabled+0xf4/0x108
[ 7538.874396] debug_smp_processor_id+0x1c/0x28
[ 7538.874406] sec_create_qps+0x24/0xe8 [hisi_sec2]
[ 7538.874408] sec_ctx_base_init+0x20/0x4d8 [hisi_sec2]
[ 7538.874411] sec_aead_ctx_init+0x68/0x180 [hisi_sec2]
[ 7538.874413] sec_aead_sha256_ctx_init+0x28/0x38 [hisi_sec2]
[ 7538.874421] crypto_aead_init_tfm+0x54/0x68
[ 7538.874423] crypto_create_tfm_node+0x6c/0x110
[ 7538.874424] crypto_alloc_tfm_node+0x74/0x288
[ 7538.874426] crypto_alloc_aead+0x40/0x50
[ 7538.874431] aead_bind+0x50/0xd0
[ 7538.874433] alg_bind+0x94/0x148
[ 7538.874439] __sys_bind+0x98/0x118
[ 7538.874441] __arm64_sys_bind+0x28/0x38
[ 7538.874445] do_el0_svc+0x88/0x258
[ 7538.874447] el0_svc+0x1c/0x28
[ 7538.874449] el0_sync_handler+0x8c/0xb8
[ 7538.874452] el0_sync+0x148/0x180
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove the unused CFB/OFB implementation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Pre-store the valid value of the sec alg support related capability
register in sec_qm_init(), which will be called by probe process.
It can reduce the number of capability register queries and avoid
obtaining incorrect values in abnormal scenarios, such as reset
failed and the memory space disabled.
Fixes: 921715b6b782 ("crypto: hisilicon/sec - get algorithm bitmap from registers")
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Extract a public function to set qm algs and remove
the similar code for setting qm algs in each module.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Hao Fang <fanghao11@huawei.com>
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When the Kunpeng accelerator executes tasks such as encryption
and decryption have minimum requirements on the number of device
queues. If the number of queues does not meet the requirement,
the process initialization will fail. Therefore, the driver checks
the number of queues on the device before registering the algorithm.
If the number does not meet the requirements, the driver does not register
the algorithm to crypto subsystem, the device is still added to the
qm_list.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If the queue isolation feature is enabled, the number of queues
supported by the device changes. When PF is enabled using the
current default number of queues, the default number of queues may
be greater than the number supported by the device. As a result,
the PF fails to be bound to the driver.
After modification, if queue isolation feature is enabled, when
the default queue parameter is greater than the number supported
by the device, the number of enabled queues will be changed to
the number supported by the device, so that the PF and driver
can be properly bound.
Fixes: 8bbecfb402f7 ("crypto: hisilicon/qm - add queue isolation support for Kunpeng930")
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
<linux/aer.h> is unused, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kai Ye <yekai13@huawei.com>
Cc: Longfang Liu <liulongfang@huawei.com>
Acked-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix that put two or more continuous blank lines inside function.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The last register logic and different register logic are combined.
Use "u32" instead of 'int' in the regs function input parameter to
simplify some checks.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Change the value of clock gating register to 0x7fff to enable
clock gating of the address prefetch module. When the device is
idle, the clock is turned off to save power.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The value of qm algorithm can change dynamically according to the
value of the capability register.
Add xxx_set_qm_algs() function to obtain the algs that the
hardware device supported from the capability register and set
them into usr mode attribute files.
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add function 'sec_get_alg_bitmap' to get hardware algorithm bitmap
before register algorithm to crypto, instead of determining
whether to register an algorithm based on hardware platform's version.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Hardware V3 and later versions support get error type from
registers. To be compatible with later hardware versions,
get error type from registers instead of fixed marco.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Hardware V3 and later versions can obtain qp num and depth supported
by the hardware from registers. To be compatible with later hardware
versions, get qp num and depth from registers instead of fixed marcos.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Before hardware V3, hardwares do not provide the feature registers,
driver resolves hardware differences based on the hardware version.
As a result, the driver does not support the new hardware.
Hardware V3 and later versions support to obtain hardware features,
such as power-gating management and doorbell isolation, through
the hardware registers. To be compatible with later hardware versions,
the features of the current device is obtained by reading the
hardware registers instead of the hardware version.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The base register address of V2 and V3 are different. HW V3 not needs
to change the BD err detection.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Before stopping the function, the driver needs to flush all the remaining
work about event irq. Therefore, accelerator drivers use a private
workqueue(qm->wq) to handle event irq instead of the system workqueue.
This patch moves alloc workqueue from sec_main.c and zip_main.c to qm.c.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add last word dumping function during sec engine controller reset.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The value of the register is changed after the task running. A debugfs
file node is added to help users to check the change of register values.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Pull VFIO updates from Alex Williamson:
- Introduce new device migration uAPI and implement device specific
mlx5 vfio-pci variant driver supporting new protocol (Jason
Gunthorpe, Yishai Hadas, Leon Romanovsky)
- New HiSilicon acc vfio-pci variant driver, also supporting migration
interface (Shameer Kolothum, Longfang Liu)
- D3hot fixes for vfio-pci-core (Abhishek Sahu)
- Document new vfio-pci variant driver acceptance criteria
(Alex Williamson)
- Fix UML build unresolved ioport_{un}map() functions
(Alex Williamson)
- Fix MAINTAINERS due to header movement (Lukas Bulwahn)
* tag 'vfio-v5.18-rc1' of https://github.com/awilliam/linux-vfio: (31 commits)
vfio-pci: Provide reviewers and acceptance criteria for variant drivers
MAINTAINERS: adjust entry for header movement in hisilicon qm driver
hisi_acc_vfio_pci: Use its own PCI reset_done error handler
hisi_acc_vfio_pci: Add support for VFIO live migration
crypto: hisilicon/qm: Set the VF QM state register
hisi_acc_vfio_pci: Add helper to retrieve the struct pci_driver
hisi_acc_vfio_pci: Restrict access to VF dev BAR2 migration region
hisi_acc_vfio_pci: add new vfio_pci driver for HiSilicon ACC devices
hisi_acc_qm: Move VF PCI device IDs to common header
crypto: hisilicon/qm: Move few definitions to common header
crypto: hisilicon/qm: Move the QM header to include/linux
vfio/mlx5: Fix to not use 0 as NULL pointer
PCI/IOV: Fix wrong kernel-doc identifier
vfio/mlx5: Use its own PCI reset_done error handler
vfio/pci: Expose vfio_pci_core_aer_err_detected()
vfio/mlx5: Implement vfio_pci driver for mlx5 devices
vfio/mlx5: Expose migration commands over mlx5 device
vfio: Remove migration protocol v1 documentation
vfio: Extend the device migration protocol with RUNNING_P2P
vfio: Define device migration protocol v2
...
|
|
struct pci_driver pointer is an input into the pci_iov_get_pf_drvdata().
Introduce helpers to retrieve the ACC PF dev struct pci_driver pointers
as we use this in ACC vfio migration driver.
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Acked-by: Kai Ye <yekai13@huawei.com>
Acked-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Link: https://lore.kernel.org/r/20220308184902.2242-7-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Move the PCI Device IDs of HiSilicon ACC VF devices to a common header
and also use a uniform naming convention.
This will be useful when we introduce the vfio PCI HiSilicon ACC live
migration driver in subsequent patches.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Acked-by: Longfang Liu <liulongfang@huawei.com>
Acked-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci_ids.h
Link: https://lore.kernel.org/r/20220308184902.2242-4-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
It is not need to enable sm4 extra mode in at HW V3. Here is fix it.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Added the register configuration of the SVA mode for HW V3.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Modify the value of type rate from new QM spec.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
To avoid repeatedly obtaining 'qm' from 'filp', parameter passing of
debugfs function directly use 'qm' instead of 'filp'.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add runtime PM support for Kunpeng930 accelerator device.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The accelerator devices support runtime PM, when device is in suspended, an
exception will occur if reading registers. Therefore, this patch uses
'debugfs_create_file' instead of 'debugfs_create_regset32' to create
debugfs file, and then the driver can get the device status before
reading the register.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When the endian configuration of the hardware is abnormal, it will
cause the SEC engine is faulty that reports empty message. And it
will affect the normal function of the hardware. Currently the soft
configuration method can't restore the faulty device. The endian
needs to be configured according to the system properties. So fix it.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Because the algs registration process has added a judgment.
So need to add the judgment for the abnormal exiting process.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Kunpeng930 sec device supports dynamic clock gating. When doing tasks,
the algorithm core is opened, and when idle, the algorithm core is closed.
This patch enables sec dynamic clock gating by writing hardware registers.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The open interface of the sva prefetching function is distinguish the chip
version. But the close interface of the sva prefetching function doesn't
distinguish the chip version. As a result, the sva prefetching close
operation is also performed on Kunpeng920, those registers are important
on Kunpeng920, which eventually leads to abnormal hardware problems. So
need to fix it immediately.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The SEC driver support configure each function's QoS in the Host
for Kunpeng930. The SEC driver needs to configure the maximum shaper
type rate.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Kunpeng930 hardware supports address prefetching to improve performance
before doing tasks in SVA scenario.
This patch enables this function in device initialization by writing
hardware registers. In the process of reset, address prefetching is
disabled to avoid the failure of interaction between accelerator device
and SMMU.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Kunpeng930 could be able to close master ooo when NFE occurs, which will
disable memory accessing from device and execute tasks. This ensures that
errors do not spread.
This patch enables the hardware to close master ooo when an error occurs
by writing hardware registers, and ensures that the driver will not drain
qp because the hardware will empty the tasks automatically.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In order to avoid reporting an exception but the error type is not
configured, the driver needs to configure the error type first, and then
enable the error interrupt. Before executing the task, hardware error
initialization is needed so that the hardware can detect the error in time.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Kunpeng930 SEC adds several new hardware error types. This patch enables
the new error types and configures the error types as NFE.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
'err_info' does not support dynamic configuration since it is const type.
Therefore, in order to support new error type later, 'err_info' is changed
to dynamic configuration.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
ctx_q_num is a module parameter set by the user to specify the
number of qp queues required to create a ctx.
When the number of qp queues allocated by PF or VF is less than
the ctx_q_num, an error will be reported when ctx is initialized
in kernel mode, which leads to the problem that the registered
algorithms cannot be used.
Therefore, when PF or VF is initialized, if the number of qp queues
is not enough to create a ctx, the kernel mode cannot be used,
and there is no need to register the kernel mode algorithms.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
Yang Shen
Weili Qian
Qi Tao
Chenghai Huang
Wenkai Lin
Herbert Xu
Zhiqi Song
Longfang Liu
Bjorn Helgaas
Kai Ye
Linus Torvalds
Shameer Kolothum