| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Short MMIO transfers that are not a multiple of four bytes in size need
a special case for the final bytes, however the existing implementation
is not endian-safe and introduces an incorrect byteswap on big-endian
kernels.
This usually does not cause problems because most systems are
little-endian and most transfers are multiple of four bytes long, but
still needs to be fixed to avoid the extra byteswap.
Change the special case for both i3c_writel_fifo() and i3c_readl_fifo()
to use non-byteswapping writesl() and readsl() with a single element
instead of the byteswapping writel()/readl() that are meant for individual
MMIO registers. As data is copied between a FIFO and a memory buffer,
the writesl()/readsl() loops are typically based on __raw_readl()/
__raw_writel(), resulting in the order of bytes in the FIFO to match
the order in the buffer, regardless of the CPU endianess.
The earlier versions in the dw-i3c and i3c-master-cdns had a correct
implementation, but the generic version that was recently added broke it.
Fixes: 733b439375b4 ("i3c: master: Add inline i3c_readl_fifo() and i3c_writel_fifo()")
Cc: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jorge Marques <jorge.marques@analog.com>
Link: https://lore.kernel.org/r/20250924201837.3691486-1-arnd@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
adi_i3c_master_wr_to_tx_fifo computes the maximum number of bytes that can be
sent to the fifo but never makes use of it, actually limit the number of bytes
sent.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202509190505.fKGvEJRa-lkp@intel.com/
Reviewed-by: Jorge Marques <jorge.marques@analog.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250924195600.122142-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
I2C adapters can already change timeout and retry parameters via IOCTL.
This allows for better tuning to workloads compared to per-adapter
defaults. So, the FIXME is not needed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250923203557.18298-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The adi-axi-common header has been moved to the upper directory.
Acked-by: Jorge Marques <jorge.marques@analog.com>
Link: https://lore.kernel.org/r/20250519-dev-axi-clkgen-limits-v6-3-bc4b3b61d1d4@analog.com
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250916091252.39265-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add shutdown handler to the Synopsys DesignWare I3C master driver,
ensuring the device is gracefully disabled during system shutdown.
The shutdown handler cancels any pending hot-join work and disables
interrupts.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Link: https://lore.kernel.org/r/20250730151207.4113708-1-manikanta.guntupalli@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
There was already a bail out for 'ret < 0', so we can always return
success at the end of the function.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/aIyzJ7HOENL1qp1l@stanley.mountain
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://lore.kernel.org/r/20250803211256.18513-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In svc_i3c_master_handle_ibi(), an IBI slot is fetched from the pool
to store the IBI payload. However, when an error condition is encountered,
the function returns without recycling the IBI slot, resulting in an IBI
slot leak.
Fixes: c85e209b799f ("i3c: master: svc: fix ibi may not return mandatory data byte")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250829012309.3562585-3-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Driver wants to nack the IBI request when the target is not in the
known address list. In below code, svc_i3c_master_nack_ibi() will
cause undefined behavior when using AUTOIBI with auto response rule,
because hw always auto ack the IBI request.
switch (ibitype) {
case SVC_I3C_MSTATUS_IBITYPE_IBI:
dev = svc_i3c_master_dev_from_addr(master, ibiaddr);
if (!dev || !is_events_enabled(master, SVC_I3C_EVENT_IBI))
svc_i3c_master_nack_ibi(master);
...
break;
AutoIBI has another issue that the controller doesn't quit AutoIBI state
after IBIWON polling timeout when there is a SDA glitch(high->low->high).
1. SDA high->low: raising an interrupt to execute IBI ISR
2. SDA low->high
3. Driver writes an AutoIBI request
4. AutoIBI process does not start because SDA is not low
5. IBIWON polling times out
6. Controller reamins in AutoIBI state and doesn't accept EmitStop request
Emitting broadcast address with IBIRESP_MANUAL avoids both issues.
Fixes: dd3c52846d59 ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250829012309.3562585-2-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add support for Analog Devices I3C Controller IP, an AXI-interfaced IP
core that supports I3C and I2C devices, multiple speed-grades and
I3C IBIs.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Link: https://lore.kernel.org/r/20250827-adi-i3c-master-v9-2-04413925abe1@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Commit 3a379bbcea0a ("i3c: Add core I3C infrastructure") set the default
adapter timeout for I2C transfers as 1000 (ms). However that parameter
is defined in jiffies not in milliseconds.
With mipi-i3c-hci driver this wasn't visible until commit c0a90eb55a69
("i3c: mipi-i3c-hci: use adapter timeout value for I2C transfers").
Fix this by setting the default timeout as HZ (CONFIG_HZ) not 1000.
Fixes: 1b84691e7870 ("i3c: dw: use adapter timeout value for I2C transfers")
Fixes: be27ed672878 ("i3c: master: cdns: use adapter timeout value for I2C transfers")
Fixes: c0a90eb55a69 ("i3c: mipi-i3c-hci: use adapter timeout value for I2C transfers")
Fixes: a747e01adad2 ("i3c: master: svc: use adapter timeout value for I2C transfers")
Fixes: d028219a9f14 ("i3c: master: Add basic driver for the Renesas I3C controller")
Fixes: 3a379bbcea0a ("i3c: Add core I3C infrastructure")
Cc: stable@vger.kernel.org # 6.17
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250905100320.954536-1-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Get rid of local DBG() macro and convert remaining debug prints to
dev_dbg() which can be controlled without code recompile when kernel is
built with dynamic debug support.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250827103009.243771-6-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
These function enter DBG("") printouts are not very useful in error
report point of view because they require code recompile. In which case
they can be replaced with more informative debug prints if needed so
remove them for now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250827103009.243771-5-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use the same "Ring" prefix in all prints that print out the ring number.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250827103009.243771-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Ring interrupt bit 7, INTR_WARN_INS_STOP_MODE was probably drafted at
some point but is marked as reserved in the MIPI I3C HCI specification
versions 1.1 and 1.2 that came out after the initial code and also in
the earlier specification versions so remove it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250827103009.243771-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Change interrupt status prints from local DBG() macro to dev_dbg() in
order to make it easier to enable them without needing to recompile code
with DEBUG defined.
While doing so, spell out the status register names as they are in the
specification to make it easier to differentiate between different
interrupt status registers.
Since dynamic debug prints can include the line number remove the "(in)"
and "(out)" markers from the PIO interrupt status prints.
Prefix the ring interrupt status print using "Ring %d" instead of "rh%d"
to make it uniform across all other prints showing the ring number.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250827103009.243771-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Stop using I2C DMA-safe API for two reasons:
- Not needed if driver is using PIO mode.
- DMA transfers needs a DWORD align sized receive bounce buffer when the
device DMA is IOMMU mapped, which is causing needless double bounce
buffering in that case.
Cc: Billy Tsai <billy_tsai@aspeedtech.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250822105630.2820009-5-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
DMA transfer faults on Intel hardware when the IOMMU is enabled and
driver initialization will fail when attempting to do the first transfer:
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [00:11.0] fault addr 0x676e3000 [fault reason 0x71] SM: Present bit in first-level paging entry is clear
i3c mipi-i3c-hci.0: ring 0: Transfer Aborted
mipi-i3c-hci mipi-i3c-hci.0: probe with driver mipi-i3c-hci failed with error -62
Reason for this is that the IOMMU setup is done for the physical devices
only and not for the virtual I3C Controller device object.
Therefore use the pointer to a physical device object with the DMA API.
Due to a data corruption observation when the device DMA is IOMMU
mapped, a properly sized receive bounce buffer is required if transfer
length is not a multiple of DWORDs.
Reported-by:
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250822105630.2820009-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
So far only I3C private and I2C transfers have required a bounce buffer
for DMA transfers when buffer is not DMA'able.
It was observed that when the device DMA is IOMMU mapped and the receive
length is not a multiple of DWORDs (32-bit), the last DWORD is padded
with stale data from the RX FIFO, corrupting 1-3 bytes beyond the
expected data.
A similar issue, though less severe, occurs when an I3C target returns
less data than requested. In this case, the padding does not exceed the
requested number of bytes, assuming the device DMA is not IOMMU mapped.
Therefore, all I3C private transfer, CCC command payload and I2C
transfer receive buffers must be properly sized for the DMA being IOMMU
mapped. Even if those buffers are already DMA safe, their size may not
be DWORD aligned.
To prepare for the device DMA being IOMMU mapped and to address the
above issue, use helpers from I3C core for DMA mapping and bounce
buffering for all DMA transfers.
For now, require bounce buffer only when the buffer is in the
vmalloc() area to avoid unnecessary copying with CCC commands and
DMA-safe I2C transfers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250822105630.2820009-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Some I3C controllers such as MIPI I3C HCI may pad the last DWORD (32-bit)
with stale data from the RX FIFO in DMA transfers if the receive length
is not DWORD aligned and when the device DMA is IOMMU mapped.
In such a case, a properly sized bounce buffer is required in order to
avoid possible data corruption. In a review discussion, proposal was to
have a common helpers in I3C core for DMA mapping and bounce buffer
handling.
Drivers may use the helper i3c_master_dma_map_single() to map a buffer
for a DMA transfer. It internally allocates a bounce buffer if buffer is
not DMA'able or when the driver requires it for a transfer.
Helper i3c_master_dma_unmap_single() does the needed cleanups and
data copying from the bounce buffer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250822105630.2820009-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add I3C controller PCI IDs on Intel Wildcat Lake-U.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250808131732.1213227-1-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
LKP found a random config which failed to build because IO accessors
were not defined:
In file included from drivers/i3c/master.c:21:
drivers/i3c/internals.h: In function 'i3c_writel_fifo':
>> drivers/i3c/internals.h:35:9: error: implicit declaration of function 'writesl' [-Werror=implicit-function-declaration]
Add the proper header to where the IO accessors are used.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202507150208.BZDzzJ5E-lkp@intel.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250717120046.9022-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704075417.3218742-1-sakari.ailus@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250704075416.3218647-1-sakari.ailus@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In a private write transfer, the driver pre-fills the FIFO to work around
the FIFO_EMPTY quirk. However, if an IBIWON event occurs, the hardware
emits a NACK and the driver initiates a retry. During the retry, driver
attempts to pre-fill the FIFO again if there is remaining data, but since
the FIFO is already full, this leads to data loss.
Check available space in FIFO to prevent overflow.
Fixes: 4008a74e0f9b ("i3c: master: svc: Fix npcm845 FIFO empty issue")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Link: https://lore.kernel.org/r/20250730003719.1825593-1-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add a basic driver for the I3C controller found in Renesas RZ/G3S and
G3E SoCs. Support I3C pure busses (tested with two targets) and mixed
busses (two I3C devices plus various I2C targets). DAA and communication
with temperature sensors worked reliably at various speeds.
Missing features such as IBI, HotJoin, and target mode will be added
incrementally.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250724094146.6443-5-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Align existing defines to follow the consistent pattern:
I3C_BUS_<PARAM>_<MAX|MIN|TYP>_<UNIT>. Prepare the codebase for adding
new parameters and help avoid duplication.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250724094146.6443-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The two clocks, driver is getting, are not being disabled/re-enabled
during runtime of the device. Eliminate one variable in state struct,
all error paths and a lot of code from probe() and remove() by using
devm_clk_get_enabled().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250713152411.74917-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Sphinx reports indentation warning on i3c_device_do_priv_xfers() return
value list:
Documentation/driver-api/i3c/device-driver-api:9: ./drivers/i3c/device.c:31: ERROR: Unexpected indentation. [docutils]
Format the list as bullet list to fix the warning.
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250702040424.18577-1-bagasdotme@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use common inline i3c_writel_fifo()/i3c_readl_fifo() methods to
simplify code since the FIFO of controller is a 32bit width.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250624-i3c-writesl-readsl-v3-3-63ccf0870f01@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use common inline i3c_writel_fifo()/i3c_readl_fifo() methods to
simplify code since the FIFO of controller is a 32bit width.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250624-i3c-writesl-readsl-v3-2-63ccf0870f01@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The I3C abstraction expects u8 buffers, but some controllers operate with
a 32-bit bus width FIFO and cannot flag valid bytes individually. To avoid
reading or writing outside the buffer bounds, use 32-bit accesses where
possible and apply memcpy for any remaining bytes
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Suggested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250624-i3c-writesl-readsl-v3-1-63ccf0870f01@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Hexadecimal values in sysfs should be prefixed with '0x' like e.g. PCI
and SCSI already do it. Also ensure the two digit length since BCR and
DCR are a byte in size.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250707115409.73545-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Replace non-standard ENOTSUPP with the SUSV4-defined error code
EOPNOTSUPP to fix below checkpatch warning:
"ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP"
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250628192027.3932-8-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Replace non-standard ENOTSUPP with the SUSV4-defined error code
EOPNOTSUPP to fix below checkpatch warning:
"ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP"
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250628192027.3932-7-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Replace non-standard ENOTSUPP with the SUSV4-defined error code
EOPNOTSUPP to fix below checkpatch warning:
"ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP"
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250628192027.3932-6-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
'I3C_BCR_HDR_CAP' is still spec v1.0 and has been renamed to 'advanced
capabilities' in v1.1 onwards. The ST pressure sensor LPS22DF does not
have HDR, but has the 'advanced cap' bit set. The core still wants to
get additional information using the CCC 'GETHDRCAP' (or GETCAPS in v1.1
onwards). Not all controllers support this CCC and will notify the upper
layers about it. For instantiating the device, we can ignore this
unsupported CCC as standard communication will work. Without this patch,
the device will not be instantiated at all.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250704204524.6124-1-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Set ret to -EINVAL if i3c_i2c_notifier_call() receives an invalid
action, resolving uninitialized warning.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250622-i3c-master-ret-uninitialized-v1-1-aabb5625c932@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
I2C adapters have their own timeout value which can be changed by
userspace if desired. Use it for I2C transfers. The default is 1Hz, so
the default behaviour is unchanged.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250604101831.56585-5-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
I2C adapters have their own timeout value which can be changed by
userspace if desired. Use it for I2C transfers. The default is 1Hz, so
the default behaviour is unchanged.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250604101831.56585-4-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
I2C adapters have their own timeout value which can be changed by
userspace if desired. Use it for I2C transfers. The default is 1Hz, so
the default behaviour is unchanged.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250604101831.56585-3-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
I2C adapters have their own timeout value which can be changed by
userspace if desired. Use it for I2C transfers. The default is 1Hz, so
the default behaviour is unchanged.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250604101831.56585-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The Kconfig file for controller drivers is only sourced if the I3C
symbol is enabled. No need to check for that in individual drivers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250506075247.1545-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use the clk_bulk API to handle clocks, so the code can support different
numbers of clocks more easily. Make the code cleaner and more flexible.
No change in functionality.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250427083230.3325700-3-carlos.song@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
According to the I3C specification, address arbitration only happens during
the START. Repeated START do not initiate arbitration, and In-Band
Interrupts (IBIs) cannot occur at this stage.
Resending the address upon a NACK in a repeat START is therefore redundant
and unnecessary. Avoid redundant retries, improving efficiency and ensuring
protocol compliance.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250429054234.4013929-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Queuing the IBI request does not need to be done earlier than emitting
the STOP. Emitting STOP immediately after receiving the IBI request can
complete the IBI transaction earlier and return the bus to idle.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250415051808.88091-3-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Moving the job from workqueue to ISR for two reasons.
1. Improve bus utilization.
If the requests are postponed to be received in the workqueue thread,
the SDA line remains low for a long time while the system loading is
high. During this period, the bus is not available for other targets
to raise requests.
2. Ensure prompt response to requests.
For timing-critical requests, the target may encouter a failure or the
event is missed if the request is not received in time.
IBI request is short, ISR can receive the data quickly and then queue a
work to handle it in the bottom half.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250415051808.88091-2-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Move "unexpected INTR_STATUS" error print before calling the IO handler
as it is more consistent that way. Otherwise it may be confusing if
generic interrupt related prints are mixed with IO handler prints.
Since this error print is more indication of missing code rather than
runtime error downgrade it to dev_warn_once().
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250409140401.299251-5-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
INTR_STATUS bit 11 INTR_HC_RESET_CANCEL was probably projected for the
MIPI I3C HCI specification version 2 but was not ever implemented.
This bit is first time specified in the v1.2 as HC_SEQ_CANCEL_STAT
"Host Controller Cancelled Transaction Sequence". Update the definition
and debug print of it accordingly.
While at it, change DBG() print to dev_dbg().
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250409140401.299251-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Status fields in INTR_STATUS register are write 1 to clear so do it
unconditionally and move clearing of them out of an if block.
Suggested-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250409140401.299251-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Return IRQ_HANDLED from the i3c_hci_irq_handler() only if some
INTR_STATUS bit was set or if DMA/PIO handler handled it.
Currently it returns IRQ_HANDLED in case INTR_STATUS is zero and IO
handler returns false. Which could be the case if interrupt comes from
other device or is spurious.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250409140401.299251-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
Arnd Bergmann
Alexandre Belloni
Wolfram Sang
Manikanta Guntupalli
Stanley Chu
Stanley Chu
Jorge Marques
Jarkko Nikula
Sakari Ailus
Krzysztof Kozlowski
Bagas Sanjaya
Carlos Song
Frank Li