| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The synchronous command completion path in ucsi_sync_control_common()
hardcodes a 5 second (5 * HZ) timeout when waiting for the PPM to signal
command completion via ACPI notification. This value matched
UCSI_TIMEOUT_MS when it was still 5000 ms, but it was not updated when
that macro was later raised to 10000 ms to fix PPM reset timeouts.
As a result, the two PPM communication paths are now inconsistent: the
polling path in ucsi_reset_ppm() respects the 10 second timeout, while
the event-driven completion path still uses 5 seconds. On machines where
the firmware is slow to respond during boot (e.g. some Lenovo ThinkPad
models such as the E14 Gen 7), commands sent after the PPM reset, such
as SET_NOTIFICATION_ENABLE and GET_CAPABILITY, can exceed 5 seconds and
cause UCSI initialization to fail with:
ucsi_acpi USBC000:00: error -ETIMEDOUT: PPM init failed
Once UCSI init aborts, USB-C PD negotiation never completes, which in
turn blocks USB-C dock enumeration since the dock depends on a successful
PD contract.
Replace the hardcoded 5 * HZ with msecs_to_jiffies(UCSI_TIMEOUT_MS) so
that both communication paths share a single, consistent timeout value,
and future adjustments to UCSI_TIMEOUT_MS are picked up automatically.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221740
Link: https://bugzilla.kernel.org/show_bug.cgi?id=2183790
Fixes: bf4f9ae1cb08c ("usb: typec: ucsi: increase timeout for PPM reset operations")
Cc: stable@vger.kernel.org
Signed-off-by: Huang Wei <huangwei@kylinos.cn>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Fedor Pchelkin <boddah8794@gmail.com>
Link: https://patch.msgid.link/20260805085725.389761-1-huangwei@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit 7aa7d4bf9d3f ("usb: typec: ucsi: Fix race condition and
ordering in port unregistration") consolidated port teardown into the
ucsi_unregister_port() helper. However, it introduced an ordering problem
in the ucsi_init() error path.
Fix this by ensuring ucsi_unregister_port() is called before we unregister
their corresponding lockdep keys.
Cc: stable@vger.kernel.org
Fixes: 7aa7d4bf9d3f ("usb: typec: ucsi: Fix race condition and ordering in port unregistration")
Reported-by: "Borah, Chaitanya Kumar" <chaitanya.kumar.borah@intel.com>
Closes: https://lore.kernel.org/all/22064276-6c56-411a-9f20-6917ceeb865f@intel.com/
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Tested-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260717104614.325250-1-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit e0c48e42d818 ("usb: typec: ucsi: yoga-c630: remove
duplicate AltModes").
The yoga_c630 driver previously implemented its own duplicate altmode
detection in yoga_c630_ucsi_update_altmodes() to work around buggy EC
firmware that returns duplicate AltModes instead of empty ones.
With the introduction of the common ucsi_altmode_is_duplicate() helper
in both the standard and nvidia registration paths, duplicate detection
is now handled automatically in the core UCSI code. This makes the
yoga_c630-specific implementation added in commit e0c48e42d818 ("usb:
typec: ucsi: yoga-c630: remove duplicate AltModes") redundant.
Remove yoga_c630_ucsi_update_altmodes() and its callback to eliminate
code duplication and simplify the driver. Note that this causes the
driver to switch back from the nvidia registration path to the standard
path, which is the original behavior before commit e0c48e42d818 ("usb:
typec: ucsi: yoga-c630: remove duplicate AltModes"). Both paths now
include duplicate detection, ensuring the firmware bug is still properly
handled.
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Link: https://patch.msgid.link/20260713084323.287516-3-acelan.kao@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Extend the duplicate altmode detection to ucsi_register_altmodes_nvidia()
which is used when a driver provides the update_altmodes() callback.
This ensures all drivers benefit from duplicate detection, whether they
use the standard registration path or the nvidia path with update_altmodes
callback.
Without this fix, drivers using the nvidia path (like yoga_c630) would
still encounter duplicate altmode registration errors from buggy firmware.
Fixes: a79f16efcd00 ("usb: typec: ucsi: Add support for the partner USB Modes")
Cc: stable <stable@kernel.org>
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Link: https://patch.msgid.link/20260713084323.287516-2-acelan.kao@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some firmware implementations incorrectly return the same altmode
multiple times at different offsets when queried via
UCSI_GET_ALTERNATE_MODES. This causes sysfs duplicate filename errors
and kernel call traces when the driver attempts to register the same
altmode twice:
sysfs: cannot create duplicate filename '/devices/.../typec/port0/port0.0/partner'
typec-thunderbolt port0-partner.1: failed to create symlinks
typec-thunderbolt port0-partner.1: probe with driver typec-thunderbolt failed with error -17
The matching rules differ by recipient:
- UCSI_RECIPIENT_CON (port) and UCSI_RECIPIENT_SOP_P (plug):
Two altmodes with identical SVID and VDO are byte-for-byte
duplicates and the second has no observable function, so drop it.
- UCSI_RECIPIENT_SOP (partner):
The typec class binds each partner altmode to a port altmode of
the same SVID via altmode_match()/device_find_child(), which
returns the first port altmode with a matching SVID. If the
partner advertises more altmodes for SVID X than the port
advertises, the surplus partner altmode(s) collapse onto an
already-paired port altmode and trigger the
"duplicate filename .../partner" sysfs error during
typec_altmode_create_links(). Use the port-side altmode count for
SVID X as the authoritative cap and reject any partner altmode
that would exceed it. This preserves legitimate multi-Mode
partner altmodes (vendor SVIDs that the port really does
advertise more than once) while filtering the firmware-generated
duplicates that have no port counterpart, and is therefore
stricter than a plain SVID+VDO comparison (which still admits the
Thunderbolt case where firmware reports the same SVID twice with
different VDOs) without being over-broad like a plain SVID match
(which would falsely drop legitimate vendor multi-Mode entries).
If a duplicate is detected, skip it and emit a clean warning instead
of generating a kernel call trace:
ucsi_acpi USBC000:00: con2: Firmware bug: duplicate partner altmode SVID 0x8087 at offset 1, ignoring.
ucsi_acpi USBC000:00: con2: VDO mismatch: 0x8087a043 vs 0x00000001
The duplicate detection logic lives in a reusable helper
ucsi_altmode_is_duplicate() and is invoked from
ucsi_register_altmodes(). It applies to all three recipient types:
partner (SOP), port (CON), and plug (SOP_P) altmodes.
Fixes: a79f16efcd00 ("usb: typec: ucsi: Add support for the partner USB Modes")
Cc: stable <stable@kernel.org>
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
unchanged: still SVID+VDO exact-dup match.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260713084323.287516-1-acelan.kao@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A synchronization issue exists during port unregistration where pending
partner work items can race against workqueue destruction, leading to
use-after-free conditions:
cros_ec_ucsi cros_ec_ucsi.3.auto: error -ETIMEDOUT: PPM init failed
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:__queue_work+0x83/0x4a0
Call Trace:
<IRQ>
__cfi_delayed_work_timer_fn+0x10/0x10
run_timer_softirq+0x3b6/0xbd0
sched_clock_cpu+0xc/0x110
irq_exit_rcu+0x18d/0x330
fred_sysvec_apic_timer_interrupt+0x5e/0x80
Fix this by ensuring strict ordering and proper serialization during
teardown:
1. Move ucsi_unregister_partner() to the beginning of the teardown
sequence and protect it under the connector mutex lock.
2. Ensure all pending partner tasks are explicitly flushed and finished
before the workqueue is destroyed.
3. Switch from mod_delayed_work() to a cancel_delayed_work() and
queue_delayed_work() sequence. This guarantees that items currently marked
as pending won't be scheduled an additional time, preventing a double
release of resources which leads to the following crash:
Oops: general protection fault, probably for non-canonical address
0xdead000000000122: 0000 [#1] SMP NOPTI
Workqueue: cros_ec_ucsi.3.auto-con2 ucsi_poll_worker
RIP: 0010:ucsi_poll_worker+0x65/0x1e0
Call Trace:
<TASK>
process_scheduled_works+0x218/0x6d0
worker_thread+0x188/0x3f0
__cfi_worker_thread+0x10/0x10
kthread+0x226/0x2a0
To ensure these rules are applied identically across both the normal
teardown and the ucsi_init() error paths, consolidate the cleanup logic
into a new helper, ucsi_unregister_port().
Cc: stable <stable@kernel.org>
Fixes: b9aa02ca39a4 ("usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode checking")
Fixes: b13abcb7ddd8 ("usb: typec: ucsi: Fix NULL pointer access")
Fixes: fac4b8633fd6 ("usb: ucsi: Ensure connector delayed work items are flushed")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://patch.msgid.link/20260707141736.1635698-1-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for many reported issues.
Included in here are:
- usb serial driver corruption and use-after-free fixes
- usb gadget rndis bugfixes for malicious/buggy host connections
- typec driver fixes for a load of different tiny reported issues
- typec mux driver revert for a broken patch in -rc1
- usb gadget driver fixes for many different reported problems
- new usb device quirks added
- usbip tool fixes and some core usbip fixes as well
- dwc3 driver fixes for minor issues
- xhci driver fixes for reported problems
- lots of other tiny usb driver fixes for many tiny issues
All of these have been in linux-next with no reported issues"
* tag 'usb-7.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (56 commits)
USB: core: ratelimit cabling message
usb: misc: usbio: fix disconnect UAF in client teardown
Revert "usb: typec: mux: avoid duplicated mux switches"
USB: chaoskey: Fix slab-use-after-free in chaoskey_release()
usb: ucsi: huawei_gaokun: move typec_altmode off stack
usb: typec: tcpci_rt1711h: unregister TCPCI port with devres
usb: typec: tcpm: Fix VDM type for Enter Mode commands
usb: typec: ucsi: cancel pending work on system suspend
usb: typec: class: drop PD lookup reference
usb: typec: ps883x: Fix DP+USB3 configuration
usb: xhci: Fix sleep in atomic context in xhci_free_streams()
xhci: sideband: fix ring sg table pages leak
usb: gadget: udc: Fix use-after-free in gadget_match_driver
usb: dwc3: run gadget disconnect from sleepable suspend context
usb: sl811-hcd: disable controller wakeup on remove
usb: typec: anx7411: use devm_pm_runtime_enable()
usb: dwc3: fix dwc3_readl() and dwc3_writel() calls in dwc3_ulpi_setup()
USB: misc: uss720: unregister parport on probe failure
usb: gadget: function: rndis: add length check for header
usb: gadget: function: rndis: add length check to response query
...
|
|
gaokun_ucsi_register_worker() registers the EC notifier before calling
ucsi_register(). If ucsi_register() fails, the worker currently only logs
the error and leaves the notifier registered. Later EC events can then
call into an unpublished UCSI instance.
The remove path also unconditionally unregisters both the EC notifier and
the UCSI device even if the delayed worker failed before both publication
steps completed.
Unregister the notifier immediately when ucsi_register() fails, and track
only the fully published state. The remove path then tears down the pair
only if both publication steps completed.
Fixes: 00327d7f2c8c ("usb: typec: ucsi: add Huawei Matebook E Go ucsi driver")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Pengyu Luo <mitltlatltl@gmail.com>
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260709123239.62930-1-pengpeng@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the %pe format specifier instead of %ld with PTR_ERR() for printing
error pointers in ucsi_register_plug(), ucsi_register_cable(), and
ucsi_register_partner(). This prints symbolic error names (e.g.
-ENOMEM) instead of errno numbers (e.g. -12), making debug logs more
readable.
This patch fixes coccinelle reported warnings:
./typec/ucsi/ucsi.c:1026:3-10: WARNING: Consider using %pe to print PTR_ERR()
./typec/ucsi/ucsi.c:1156:3-10: WARNING: Consider using %pe to print PTR_ERR()
./typec/ucsi/ucsi.c:967:3-10: WARNING: Consider using %pe to print PTR_ERR()
Signed-off-by: Subasri S <subasris1210@gmail.com>
Link: https://patch.msgid.link/20260709-subasri-usb-ucsi-v1-v1-1-74bed201e489@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The typec_altmode structure contains a 'struct device' object
that cannot be allocated on the stack because of its size, even
when ignoring the lifetime rules:
drivers/usb/typec/ucsi/ucsi_huawei_gaokun.c:326:13: error: stack frame size (1456) exceeds limit (1280) in 'gaokun_ucsi_usb_notify_ind' [-Werror,-Wframe-larger-than]
326 | static void gaokun_ucsi_usb_notify_ind(struct gaokun_ucsi *uec)
Since the altmode is always associated with a port here, move
it into the port object and avoid at least the stack allocation
issue.
Fixes: 1c2b66a7d725 ("usb: ucsi: huawei_gaokun: support mode switching")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Pengyu Luo <mitltlatltl@gmail.com>
Link: https://patch.msgid.link/20260618143341.1900221-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current ucsi_data structure inside ucsi_debugfs_entry caps the
response payload layout to exactly 16 bytes via low and high 64-bit
fields. However, standard UCSI specifications define core data
structures that require messages larger than this 16-byte boundary.
Without this expansion, vital telemetry metrics cannot be captured. For
example, the GET_CONNECTOR_STATUS -> Voltage Reading fields, and the
GET_LPM_PPM_INFO -> HW Version fields reside starting at or beyond byte
offset 16. Under the current implementation, reading the debugfs
'response' attribute truncates this extra data, rendering these
extended operational metrics unreadable.
Fix this by expanding the ucsi_data structure with an 'ext' field to
provide structural capacity for payloads extending beyond 16 bytes.
Update ucsi_resp_show() to print the extended field block directly
prepended to the high/low data stream to ensure readability while
maintaining structural continuity.
Signed-off-by: Madhu M <madhu.m@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260630132435.458563-1-madhu.m@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ucsi_register() creates per-instance debugfs entries, but
ucsi_unregister() keeps them around until ucsi_destroy().
Drivers like ucsi_glink that unregister/register the same UCSI
instance across remoteproc restart then try to create an already
existing debugfs directory and log:
debugfs: 'pmic_glink.ucsi.0' already exists in 'ucsi'
Unregister debugfs entries as part of ucsi_unregister(), and
clear ucsi->debugfs after freeing it so repeated unregister
paths remain safe.
Assisted-by: Codex:GPT-5.5
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Fixes: df0383ffad64 ("usb: typec: ucsi: Add debugfs for ucsi commands")
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # X1E80100 CRD
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260611-usci-unregister-debugfs-v1-1-f4a518a94f27@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the code enqueue work items using {queue|mod}_delayed_work(),
using system_long_wq. This workqueue should be used when long works are
expected and it is a per-cpu workqueue.
The function(s) end up calling __queue_delayed_work(), which set a global
timer that could fire anywhere, enqueuing the work where the timer fired.
Unbound works could benefit from scheduler task placement, to optimize
performance and power consumption. Long work shouldn't stick to a single
CPU.
Recently, a new unbound workqueue specific for long running work has
been added:
c116737e972e ("workqueue: Add system_dfl_long_wq for long unbound works")
Since the workqueue work doesn't rely on per-cpu variables, there is no
obvious reason that justify the use of a per-cpu workqueue. So change
system_long_wq with system_dfl_long_wq so that the work may benefit from
scheduler task placement.
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260525074857.30816-1-marco.crivellari@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On a Dell XPS 13 9360 (BIOS 2.21.0), entering system suspend (deep/S3)
races a pending UCSI connector-change worker against the ACPI EC teardown.
The worker evaluates the UCSI _DSM (GET_CONNECTOR_STATUS), whose AML
accesses the Embedded Controller. By that point the ACPI EC has already
been stopped for suspend, so the EC address space handler rejects the
access with AE_BAD_PARAMETER, aborting the AML and failing the connector
query:
[22314.689495] ACPI: EC: interrupt blocked
[22314.711981] ACPI: PM: Preparing to enter system sleep state S3
[22314.743260] ACPI: EC: event blocked
[22314.743265] ACPI: EC: EC stopped
[22314.743267] ACPI: PM: Saving platform NVS memory
[22314.744241] ACPI Error: AE_BAD_PARAMETER, Returned by Handler for [EmbeddedControl] (20260408/evregion-303)
[22314.744432] ACPI Error: Aborting method \_SB.PCI0.LPCB.ECDV.ECW1 due to previous error (AE_BAD_PARAMETER) (20260408/psparse-543)
[22314.744673] ACPI Error: Aborting method \ECWB due to previous error (AE_BAD_PARAMETER) (20260408/psparse-543)
[22314.745201] ACPI Error: Aborting method \_SB.UBTC._DSM due to previous error (AE_BAD_PARAMETER) (20260408/psparse-543)
[22314.745394] ACPI: \_SB_.UBTC: failed to evaluate _DSM c298836f-a47c-e411-ad36-631042b5008f rev:1 func:1 (0x1001)
[22314.745414] ucsi_acpi USBC000:00: ucsi_acpi_dsm: failed to evaluate _DSM 1
[22314.745424] ucsi_acpi USBC000:00: ucsi_handle_connector_change: GET_CONNECTOR_STATUS failed (-5)
ucsi_acpi implements a resume callback but no suspend callback, so nothing
cancels the connector-change work before the firmware/EC is torn down.
Add a `ucsi_suspend()` core helper that cancels the pending init and
connector-change work, and wire it into ucsi_acpi's PM ops. The connector
state is re-read on resume by `ucsi_resume()`, so cancelling the work loses
nothing.
Fixes: 4e3a50293c2b ("usb: typec: ucsi: acpi: Implement resume callback")
Cc: stable <stable@kernel.org>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Assisted-by: Claude Opus 4.8
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260703110738.8457-2-pmenzel@molgen.mpg.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the UCSI Specification Revision 3.1 RC1, bits 32-63 of the SET_NEW_CAM
command hold the 32-bit Alternate Mode Specific (AMSpecific) field.
For DisplayPort Alternate Mode, this field must contain the full
32-bit DisplayPort configuration VDO payload that the OPM wants the
connector to operate in, rather than just the pin assignment value.
This AMSpecific value follows the DisplayPort Configurations defined
in the DisplayPort Alt Mode on USB Type-C Specification v2.1a,
Table 5-13: SOP DisplayPort Configurations.
Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Madhu M <madhu.m@intel.com>
Reviewed-by: Jameson Thies <jthies@google.com>
Reviewed-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260619153311.3526083-1-madhu.m@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace the #include of <linux/mod_devicetable.h> by the more specific
<linux/device-id/*.h> where applicable. For most cases the include
can be dropped completely, only a few drivers need one or two headers
added.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1a3f2007c5c5dcf555c09a4035ce3ae8ef1b6c49.1782808461.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
|
|
The threaded IRQ handler ccg_irq_handler() calls ucsi_notify_common(),
which on a connector-change event calls ucsi_connector_change() and
schedules connector work. In ucsi_ccg_remove(), ucsi_destroy() frees
uc->ucsi (kfree) before free_irq() is called, so a handler invocation
already in flight may access the freed object after ucsi_destroy().
CPU 0 (remove) | CPU 1 (threaded IRQ)
ucsi_destroy(uc->ucsi) | ccg_irq_handler()
kfree(ucsi) // FREE | ucsi_notify_common(uc->ucsi) // USE
Move free_irq() before ucsi_destroy() in the remove path. It is kept
after ucsi_unregister(): ucsi_unregister() cancels connector work whose
handler issues GET_CONNECTOR_STATUS through ucsi_send_command_common(),
which waits for a completion that is signalled from the IRQ handler, so
the IRQ must stay active until that work has been cancelled.
The probe error path already orders free_irq() before ucsi_destroy().
This bug was found by static analysis.
Fixes: e32fd989ac1c ("usb: typec: ucsi: ccg: Move to the new API")
Cc: stable <stable@kernel.org>
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260616132011.103279-1-fanwu01@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The existing implementation assigned these flags backwards, configuring
the partner's DisplayPort role to match the port's role instead of
complementing it.
This prevents proper configuration during DP altmode activation, often
causing `pin_assignment` to remain 0 in `dp_altmode_configure()` and
resulting in VDM negotiation failures:
[ 583.328246] typec port1.1: VDM 0xff01a150 failed
Additionally, the fix ensures that the `pin_assignment` sysfs attribute
displays the correct values.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260601142837.3240207-1-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB PHY (QMP Combo PHY) is always initialized in USB3+DP mode. In
the past, there was no MUX, and it was unnecessary to set it, since
MSM only supported 2-lane DP. But now, MST and 4-lane DP support has
been added to MSM, and a MUX has been added to the PHY. To support
4-lane DP and mode switching for gaokun, get the MUX and set it.
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260607101844.820064-1-mitltlatltl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB and Thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for UCSI SET_PDOS command as per UCSI specification v2.1 and
above to debugfs.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pooja Katiyar <pooja.katiyar@intel.com>
Link: https://patch.msgid.link/e3e127122c0a6910c4840a13d5c74ab5fc4eb868.1778798352.git.pooja.katiyar@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add debugfs entry for writing message_out data structure to handle
UCSI 2.1 and 3.0 commands through debugfs interface.
Users writing to the message_out debugfs file should ensure the input
data adheres to the following format:
1. Input must be a non-empty valid hexadecimal string.
2. Input length of hexadecimal string must not exceed 256 bytes of
length to be in alignment with the message out data structure size
as per the UCSI specification v2.1.
3. If the input string length is odd, then user needs to prepend a
'0' to the first character for proper hex conversion.
Below are examples of valid hex strings. Note that these values are
just examples. The exact values depend on specific command use case.
#echo 1A2B3C4D > message_out
#echo 01234567 > message_out
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pooja Katiyar <pooja.katiyar@intel.com>
Link: https://patch.msgid.link/812820ed3caae2d9ab86e4b26022c5a36b645f86.1778798352.git.pooja.katiyar@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for UCSI message_out data structure. The UCSI
interface defines separate message_in and message_out data
structure for bidirectional communication, where commands
like Set PDOs and LPM Firmware Update require writing data
to message_out before command execution.
Add write_message_out operation to ucsi_operations structure
to allow platform drivers to implement message_out data writing
capability.
Update ucsi_sync_control_common to accept message_out parameters
and call write_message_out followed by command execution to
maintain proper sequencing as per the UCSI specification.
Introduce ucsi_write_message_out_command for commands that need
to send message_out data, while maintaining ucsi_send_command
for commands that only require message_in response data.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pooja Katiyar <pooja.katiyar@intel.com>
Link: https://patch.msgid.link/6d4e1ba7f92e713638f66925ae6389528597df6e.1778798352.git.pooja.katiyar@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Lockdep detects a possible recursive locking scenario during
ucsi init:
[ 5.418616] ============================================
[ 5.418634] WARNING: possible recursive locking detected
[ 5.418706] --------------------------------------------
[ 5.418725] kworker/4:1/82 is trying to acquire lock:
[ 5.418759] ffff888119a34648 (&con->lock){+.+.}-{3:3}, at: ucsi_init_work+0x1a78/0x2eb0 [typec_ucsi]
[ 5.418801]
but task is already holding lock:
[ 5.418835] ffff888119a34080 (&con->lock){+.+.}-{3:3}, at: ucsi_init_work+0x1a78/0x2eb0 [typec_ucsi]
[ 5.418884]
other info that might help us debug this:
[ 5.418904] Possible unsafe locking scenario:
[ 5.418937] CPU0
[ 5.418956] ----
[ 5.418991] lock(&con->lock);
[ 5.419013] lock(&con->lock);
[ 5.419033]
*** DEADLOCK ***
[ 5.419387] Call Trace:
[ 5.419406] <TASK>
[ 5.419425] dump_stack_lvl+0x61/0xa0
[ 5.419448] print_deadlock_bug+0x4a6/0x650
[ 5.419483] __lock_acquire+0x62b6/0x7f50
[ 5.419507] lock_acquire+0x11b/0x390
[ 5.419654] __mutex_lock+0xbc/0xcd0
[ 5.419741] ucsi_init_work+0x1a78/0x2eb0
[ 5.419785] ? worker_thread+0xf53/0x2bc0
[ 5.419819] worker_thread+0xff4/0x2bc0
[ 5.419842] kthread+0x2a7/0x330
[ 5.419863] ? __pfx_worker_thread+0x10/0x10
[ 5.419896] ? __pfx_kthread+0x10/0x10
[ 5.419916] ret_from_fork+0x38/0x70
[ 5.419936] ? __pfx_kthread+0x10/0x10
[ 5.419969] ret_from_fork_asm+0x1b/0x30
[ 5.419991] </TASK>
[ 5.420009] ---[ end trace 0000000000000000 ]---
The problem is that all connector locks belong to the same
lockdep lock class, so the following loop:
for (i = 0; i < ucsi->cap.num_connectors; i++)
ucsi_register_port(connector[i])
mutex_lock(&connector[i]->lock)
looks like a recursive acquire of the same mutex. Put each connector
lock into a dedicated lock class so that lockdep doesn't see it as a
possible recursion.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260515060042.136083-1-senozhatsky@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We only need to update the power_supply on power role change if the port
is connected, because otherwise the online status should be the same for
both cases.
Cc: stable <stable@kernel.org>
Fixes: 7616f006db07 ("usb: typec: ucsi: Update power_supply on power role change")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Reported-and-tested-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Link: https://patch.msgid.link/20260519-ucsi-fix-2-v1-2-6f1239535187@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CrOS EC may send a connector status change event with the power
direction changed flag set even if the power direction hasn't actually
changed after initiating a SET_PDR command internally [1]. In practice
this happens on every system suspend due to other changes performed by
the EC [2][3][4], causing suspend to fail.
Fix this by checking if the power role change actually happened before
handling it.
[1]: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/ec/zephyr/subsys/pd_controller/pdc_power_mgmt.c;l=1689;drc=2d5a1cffce4e5ac8a39442cb3b764d2d5e1cf794
[2]: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/ec/zephyr/subsys/pd_controller/pdc_power_mgmt.c;l=3923;drc=2d5a1cffce4e5ac8a39442cb3b764d2d5e1cf794
[3]: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/ec/zephyr/subsys/pd_controller/pdc_power_mgmt.c;l=5094;drc=2d5a1cffce4e5ac8a39442cb3b764d2d5e1cf794
[4]: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/ec/zephyr/subsys/pd_controller/pdc_power_mgmt.c;l=2229;drc=2d5a1cffce4e5ac8a39442cb3b764d2d5e1cf794
Cc: stable <stable@kernel.org>
Fixes: 7616f006db07 ("usb: typec: ucsi: Update power_supply on power role change")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Reported-and-tested-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260519-ucsi-fix-2-v1-1-6f1239535187@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
The mentioned robustness is relevant for a planned change to struct
i2c_device_id that replaces .driver_data by an anonymous union.
While touching all these arrays, unify usage of whitespace in the list
terminator.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260518110142.637215-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The connector number in a UCSI CCI notification is a 7-bit field
supplied by the PPM. ucsi_connector_change() uses it to index the
ucsi->connector[] array without checking it against the number of
connectors the PPM reported at init time, so a buggy or malicious PPM
(EC firmware, or an I2C-attached UCSI controller on the ccg / stm32g0 /
glink transports) can drive schedule_work() on memory past the end of
the array.
Reject connector numbers that are zero or exceed cap.num_connectors
before dereferencing the array.
Assisted-by: gkh_clanker_t1000
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Benson Leung <bleung@chromium.org>
Cc: Jameson Thies <jthies@google.com>
Cc: Nathan Rebello <nathan.c.rebello@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Pooja Katiyar <pooja.katiyar@intel.com>
Cc: Hsin-Te Yuan <yuanhsinte@chromium.org>
Cc: Abel Vesa <abelvesa@kernel.org>
Cc: stable <stable@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://patch.msgid.link/2026051351-truck-steadfast-df48@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ucsi_displayport_vdm() handles a DP_CMD_CONFIGURE by copying the first
payload VDO from data[], but unlike the equivalent handler in
altmodes/displayport.c it does not check that count covers a VDO beyond
the header. A header-only Configure VDM (count == 1) would read one u32
past the caller's array.
In the normal UCSI path the caller controls count, so this is hardening
for non-standard delivery paths. NAK and bail when no configuration VDO
is present, matching the generic DP altmode driver's existing guard.
Assisted-by: gkh_clanker_t1000
Cc: Pooja Katiyar <pooja.katiyar@intel.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/2026051351-vividly-flattered-eb3d@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
do_flash() locates the first .cyacd record with
p = strnchr(fw->data, fw->size, ':');
while (p < eof) {
s = strnchr(p + 1, eof - p - 1, ':');
...
}
If the firmware image contains no ':' byte, strnchr() returns NULL.
NULL compares less than the valid kernel pointer eof, so the loop body
runs and strnchr() is called with p + 1 == (void *)1 and a length of
roughly (unsigned long)eof, causing a wonderful crash.
The not_signed_fw fallthrough earlier in do_flash() and the chip-state
branches in ccg_fw_update_needed() allow an unsigned blob to reach this
loop, so a root user who can place a crafted file under /lib/firmware
and write the do_flash sysfs attribute can trigger the oops.
Bail out with -EINVAL when the initial strnchr() returns NULL.
Assisted-by: gkh_clanker_t1000
Cc: stable <stable@kernel.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026051405-posture-shrill-7884@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 7.1-rc1.
Lots of little things in here, nothing major, just constant
improvements, updates, and new features. Highlights are:
- new USB power supply driver support.
These changes did touch outside of drivers/usb/ but got acks from
the relevant mantainers for them.
- dts file updates and conversions
- string function conversions into "safer" ones
- new device quirks
- xhci driver updates
- usb gadget driver minor fixes
- typec driver additions and updates
- small number of thunderbolt driver changes
- dwc3 driver updates and additions of new hardware support
- other minor driver updates
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (176 commits)
usb: dwc3: starfive: Add JHB100 USB 2.0 DRD controller
dt-bindings: usb: dwc3: add support for StarFive JHB100
dt-bindings: usb: atmel,at91sam9rl-udc: convert to DT schema
dt-bindings: usb: atmel,at91rm9200-udc: convert to DT schema
dt-bindings: usb: generic-ehci: fix schema structure and add at91sam9g45 constraints
dt-bindings: usb: generic-ohci: add AT91RM9200 OHCI binding support
arm: dts: at91: remove unused #address-cells/#size-cells from sam9x60 udc node
drivers/usb/host: Fix spelling error 'seperate' -> 'separate'
usbip: tools: add hint when no exported devices are found
USB: serial: iuu_phoenix: fix iuutool author name
usb: gadget: f_ncm: validate minimum block_len in ncm_unwrap_ntb()
usb: gadget: f_phonet: fix skb frags[] overflow in pn_rx_complete()
usb: gadget: f_hid: Add missing error code
usb: typec: cros_ec_ucsi: Load driver from OF and ACPI definitions
dt-bindings: chrome: Add cros-ec-ucsi compatibility to typec binding
USB: of: Simplify with scoped for each OF child loop
usbip: validate number_of_packets in usbip_pack_ret_submit()
usb: gadget: renesas_usb3: validate endpoint index in standard request handlers
usb: core: config: reverse the size check of the SSP isoc endpoint descriptor
usb: typec: ucsi: Set usb mode on partner change
...
|
|
Add support for cros_ec_ucsi to load based on "google,cros-ec-ucsi"
compatible devices and "GOOG0021" ACPI nodes.
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Link: https://patch.msgid.link/20260403223357.1896403-3-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the partner usb_mode is only set in ucsi_register_partner().
If the partner enters USB4 operation after it is registered, this is not
reported to the typec class. The UCSI spec states that the Connector
Partner Changed bit can represent a Connector Partner Flags change. When
handling a UCSI partner change, check the partner flags for USB4
operation.
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://patch.msgid.link/20260402182438.867396-1-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Notifications can arrive before ucsi_init() has populated
ucsi->cap.num_connectors via GET_CAPABILITY. At that point
num_connectors is still 0, causing all valid connector numbers to be
incorrectly rejected as bogus.
Skip the bounds check when num_connectors is 0 (not yet initialized).
Pre-init notifications are already handled safely by the early-event
guard in ucsi_connector_change().
Reported-by: Takashi Iwai <tiwai@suse.de>
Fixes: d2d8c17ac01a ("usb: typec: ucsi: validate connector number in ucsi_notify_common()")
Cc: stable@vger.kernel.org
Signed-off-by: Nathan Rebello <nathan.c.rebello@gmail.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260407063958.863-1-nathan.c.rebello@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here to build on and for testing
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The connector number extracted from CCI via UCSI_CCI_CONNECTOR() is a
7-bit field (0-127) that is used to index into the connector array in
ucsi_connector_change(). However, the array is only allocated for the
number of connectors reported by the device (typically 2-4 entries).
A malicious or malfunctioning device could report an out-of-range
connector number in the CCI, causing an out-of-bounds array access in
ucsi_connector_change().
Add a bounds check in ucsi_notify_common(), the central point where CCI
is parsed after arriving from hardware, so that bogus connector numbers
are rejected before they propagate further.
Fixes: bdc62f2bae8f ("usb: typec: ucsi: Simplified registration and I/O API")
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Nathan Rebello <nathan.c.rebello@gmail.com>
Link: https://patch.msgid.link/20260313222453.123-1-nathan.c.rebello@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On X1E80100, when we connect a USB4 capable dock, the PARTNER_FLAGS
indicate USB4_GEN3 being set whilst keeping the PARTNER_FLAGS_USB
cleared. Due to this, during ucsi_partner_change call, the usb role
is marked as ROLE_NONE and passed to DWC3 controller the same way.
Fix this by adding UCSI_USB4_IMPLIES_USB quirk and check for it to
decide and pass on proper ROLE information to DWC3 layer.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260312101431.2375709-1-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ucsi_run_command trace event is exposed in tracefs, but it never
produces any output because the UCSI core never invokes the associated
tracepoint. As a result, enabling the event under events/ucsi/ yields
no traces, preventing users from inspecting UCSI command sequencing.
Wire the tracepoint into the UCSI command path so that commands are
properly reported.
Example:
50.692342: ucsi_run_command: GET_CONNECTOR_STATUS -> OK (err=0)
50.692345: ucsi_connector_change: port0 status: change=4800, ...
51.750298: ucsi_run_command: GET_CABLE_PROPERTY -> FAIL (err=-5)
51.773360: ucsi_run_command: GET_CONNECTOR_STATUS -> OK (err=0)
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260217103403.1956-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The gaokun_ucsi_ops structure is only used within its translation unit
and is not referenced from any other file. Add the 'static' qualifier
to avoid unnecessary symbol export.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202603050203.KD4RWA00-lkp@intel.com
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260305144054.27848-1-mitltlatltl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add Glymur and Kaanapali compatible strings which both need
UCSI_DELAY_DEVICE_PDOS quirk.
Signed-off-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260209204915.1983997-5-anjelique.melendez@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver updates for
7.0-rc1. Overall more lines were removed than added, thanks to
dropping the obsolete isp1362 USB host controller driver, always a
nice change.
Other than that, nothing major happening here, highlights are:
- lots of dwc3 driver updates and new hardware support added
- usb gadget function driver updates
- usb phy driver updates
- typec driver updates and additions
- USB rust binding updates for syntax and formatting changes
- more usb serial device ids added
- other smaller USB core and driver updates and additions
All of these have been in linux-next for a long time, with no reported
problems"
* tag 'usb-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (77 commits)
usb: typec: ucsi: Add Thunderbolt alternate mode support
usb: typec: hd3ss3220: Check if regulator needs to be switched
usb: phy: tegra: parametrize PORTSC1 register offset
usb: phy: tegra: parametrize HSIC PTS value
usb: phy: tegra: return error value from utmi_wait_register
usb: phy: tegra: cosmetic fixes
dt-bindings: usb: renesas,usbhs: Add RZ/G3E SoC support
usb: dwc2: fix resume failure if dr_mode is host
usb: cdns3: fix role switching during resume
usb: dwc3: gadget: Move vbus draw to workqueue context
USB: serial: option: add Telit FN920C04 RNDIS compositions
usb: dwc3: Log dwc3 address in traces
usb: gadget: tegra-xudc: Add handling for BLCG_COREPLL_PWRDN
usb: phy: tegra: add HSIC support
usb: phy: tegra: use phy type directly
usb: typec: ucsi: Enforce mode selection for cros_ec_ucsi
usb: typec: ucsi: Support mode selection to activate altmodes
usb: typec: Introduce mode_selection bit
usb: typec: Implement mode selection
usb: typec: Expose alternate mode priority via sysfs
...
|
|
Introduce support for Thunderbolt (TBT) alternate mode to the UCSI driver.
This allows the driver to manage the entry and exit of TBT altmode by
providing the necessary typec_altmode_ops.
ucsi_altmode_update_active() is invoked when the Connector Partner Changed
bit is set in the GET_CONNECTOR_STATUS data. This ensures that the
alternate mode's active state is synchronized with the current mode the
connector is operating in.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260206115754.828954-1-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The mode selection sequence is initiated by the driver after all partner
alternate modes have been successfully registered.
When a partner is disconnected, the driver also stops the mode selection
process and releases resources via `typec_mode_selection_delete`.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260119131824.2529334-8-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the ucsi port driver supports modes selection, it should implement
`add_partner_altmodes` and `remove_partner_altmodes` ucsi operations. With
these operations the driver can manage the mode selection process.
Once partner altmodes are registered, `add_partner_altmodes` is called to
start the mode selection. When the partner is unregistered,
`remove_partner_altmodes` is supposed to stop any ongoing processes and
clean up the resources.
`typec_altmode_state_update` informes mode selection about the current mode
of the Type-C connector.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260119131824.2529334-7-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove <linux/hex.h> from <linux/kernel.h> and update all users/callers of
hex.h interfaces to directly #include <linux/hex.h> as part of the process
of putting kernel.h on a diet.
Removing hex.h from kernel.h means that 36K C source files don't have to
pay the price of parsing hex.h for the roughly 120 C source files that
need it.
This change has been build-tested with allmodconfig on most ARCHes. Also,
all users/callers of <linux/hex.h> in the entire source tree have been
updated if needed (if not already #included).
Link: https://lkml.kernel.org/r/20251215005206.2362276-1-rdunlap@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Yury Norov (NVIDIA) <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
Huang Wei
Greg Kroah-Hartman
Andrei Kuchynski
Chia-Lin Kao (AceLan)
Linus Torvalds
Pengpeng Hou
Subasri S
Arnd Bergmann
Madhu M
Bjorn Andersson
Marco Crivellari
Paul Menzel
Uwe Kleine-König (The Capable Hub)
Fan Wu
Pengyu Luo
Pooja Katiyar
Sergey Senozhatsky
Myrrh Periwinkle
Jameson Thies
Nathan Rebello
Krishna Kurapati
Loic Poulain
Anjelique Melendez
Kees Cook
Randy Dunlap