Merge tag 'soc-newsoc-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull new SoC support from Arnd Bergmann:
 "These five newly supported chips come with both devicetree
  descriptions and the changes to wire them up to the build system for
  easier bisection.

  The chips in question are:

   - Marvell PXA1908 was the first 64-bit mobile phone chip from Marvell
     in the product line that started with the Digital StrongARM SA1100
     based PDAs and continued with the Intel PXA2xx that dominated early
     smartphones. This one only made it only into a few products before
     the entire product line was cut in 2015.

   - The QiLai SoC is made by RISC-V core designer Andes Technologies
     and is in the 'Voyager' reference board in MicroATX form factor. It
     uses four in-order AX45MP cores, which is the midrange product from
     Andes.

   - CIX P1 is one of the few Arm chips designed for small workstations,
     and this one uses 12 Cortex-A720/A520 cores, making it also one of
     the only ARMv9.2 machines that one can but at the moment.

   - Axiado AX3000 is an embedded chip with relative small Cortex-A53
     CPU cores described as a "Trusted Control/Compute Unit" that can be
     used as a BMC in servers. In addition to the usual I/O, this one
     comes with 10GBit ethernet and and a 4TOPS NPU.

   - Sophgo SG2000 is an embedded chip that comes with both RISC-V and
     Arm cores that can run Linux. This was already supported for RISC-V
     but now it also works on Arm

  One more chip, the Black Sesame C1200 did not make it in tirm for the
  merge window"

* tag 'soc-newsoc-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
  arm64: defconfig: Enable rudimentary Sophgo SG2000 support
  arm64: Add SOPHGO SOC family Kconfig support
  arm64: dts: sophgo: Add Duo Module 01 Evaluation Board
  arm64: dts: sophgo: Add Duo Module 01
  arm64: dts: sophgo: Add initial SG2000 SoC device tree
  MAINTAINERS: Add entry for Axiado
  arm64: defconfig: enable the Axiado family
  arm64: dts: axiado: Add initial support for AX3000 SoC and eval board
  arm64: add Axiado SoC family
  dt-bindings: i3c: cdns: add Axiado AX3000 I3C controller
  dt-bindings: serial: cdns: add Axiado AX3000 UART controller
  dt-bindings: gpio: cdns: add Axiado AX3000 GPIO variant
  dt-bindings: gpio: cdns: convert to YAML
  dt-bindings: arm: axiado: add AX3000 EVK compatible strings
  dt-bindings: vendor-prefixes: Add Axiado Corporation
  MAINTAINERS: Add CIX SoC maintainer entry
  arm64: dts: cix: Add sky1 base dts initial support
  dt-bindings: clock: cix: Add CIX sky1 scmi clock id
  arm64: defconfig: Enable CIX SoC
  mailbox: add CIX mailbox driver
  ...

42 files changed, 3428 insertions, 63 deletions

diff --git a/Documentation/devicetree/bindings/arm/axiado.yaml b/Documentation/devicetree/bindings/arm/axiado.yaml
new file mode 100644
index 000000000000..bfabe7b32e65
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/axiado.yaml
@@ -0,0 +1,23 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/axiado.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Axiado Platforms
+
+maintainers:
+  - Harshit Shah <hshah@axiado.com>
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+      - description: AX3000 based boards
+        items:
+          - enum:
+              - axiado,ax3000-evk       # Axiado AX3000 Evaluation Board
+          - const: axiado,ax3000       # Axiado AX3000 SoC
+
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/arm/cix.yaml b/Documentation/devicetree/bindings/arm/cix.yaml
new file mode 100644
index 000000000000..114dab4bc4d2
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/cix.yaml
@@ -0,0 +1,26 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/cix.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: CIX platforms
+
+maintainers:
+  - Peter Chen <peter.chen@cixtech.com>
+  - Fugang Duan <fugang.duan@cixtech.com>
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+
+      - description: Radxa Orion O6
+        items:
+          - const: radxa,orion-o6
+          - const: cix,sky1
+
+additionalProperties: true
+
+...
diff --git a/Documentation/devicetree/bindings/arm/mrvl/mrvl.yaml b/Documentation/devicetree/bindings/arm/mrvl/mrvl.yaml
index 4c43eaf3632e..f73bb8ec3a1a 100644
--- a/Documentation/devicetree/bindings/arm/mrvl/mrvl.yaml
+++ b/Documentation/devicetree/bindings/arm/mrvl/mrvl.yaml
@@ -35,6 +35,11 @@ properties:
           - enum:
               - dell,wyse-ariel
           - const: marvell,mmp3
+      - description: PXA1908 based boards
+        items:
+          - enum:
+              - samsung,coreprimevelte
+          - const: marvell,pxa1908
 
 additionalProperties: true
 
diff --git a/Documentation/devicetree/bindings/gpio/cdns,gpio.txt b/Documentation/devicetree/bindings/gpio/cdns,gpio.txt
deleted file mode 100644
index 706ef00f5c64..000000000000
--- a/Documentation/devicetree/bindings/gpio/cdns,gpio.txt
+++ /dev/null
@@ -1,43 +0,0 @@
-Cadence GPIO controller bindings
-
-Required properties:
-- compatible: should be "cdns,gpio-r1p02".
-- reg: the register base address and size.
-- #gpio-cells: should be 2.
-	* first cell is the GPIO number.
-	* second cell specifies the GPIO flags, as defined in
-		<dt-bindings/gpio/gpio.h>. Only the GPIO_ACTIVE_HIGH
-		and GPIO_ACTIVE_LOW flags are supported.
-- gpio-controller: marks the device as a GPIO controller.
-- clocks: should contain one entry referencing the peripheral clock driving
-	the GPIO controller.
-
-Optional properties:
-- ngpios: integer number of gpio lines supported by this controller, up to 32.
-- interrupts: interrupt specifier for the controllers interrupt.
-- interrupt-controller: marks the device as an interrupt controller. When
-	defined, interrupts, interrupt-parent and #interrupt-cells
-	are required.
-- interrupt-cells: should be 2.
-	* first cell is the GPIO number you want to use as an IRQ source.
-	* second cell specifies the IRQ type, as defined in
-		<dt-bindings/interrupt-controller/irq.h>.
-		Currently only level sensitive IRQs are supported.
-
-
-Example:
-	gpio0: gpio-controller@fd060000 {
-		compatible = "cdns,gpio-r1p02";
-		reg =<0xfd060000 0x1000>;
-
-		clocks = <&gpio_clk>;
-
-		interrupt-parent = <&gic>;
-		interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
diff --git a/Documentation/devicetree/bindings/gpio/cdns,gpio.yaml b/Documentation/devicetree/bindings/gpio/cdns,gpio.yaml
new file mode 100644
index 000000000000..a84d60b39459
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/cdns,gpio.yaml
@@ -0,0 +1,84 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/cdns,gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence GPIO Controller
+
+maintainers:
+  - Jan Kotas <jank@cadence.com>
+
+properties:
+  compatible:
+    oneOf:
+      - const: cdns,gpio-r1p02
+      - items:
+          - enum:
+              - axiado,ax3000-gpio
+          - const: cdns,gpio-r1p02
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  ngpios:
+    minimum: 1
+    maximum: 32
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 2
+    description: |
+      - First cell is the GPIO line number.
+      - Second cell is flags as defined in <dt-bindings/gpio/gpio.h>,
+        only GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW supported.
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+    description: |
+      - First cell is the GPIO line number used as IRQ.
+      - Second cell is the trigger type, as defined in
+        <dt-bindings/interrupt-controller/irq.h>.
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - gpio-controller
+  - "#gpio-cells"
+
+if:
+  required: [interrupt-controller]
+then:
+  required:
+    - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    gpio0: gpio-controller@fd060000 {
+        compatible = "cdns,gpio-r1p02";
+        reg = <0xfd060000 0x1000>;
+        clocks = <&gpio_clk>;
+
+        interrupt-parent = <&gic>;
+        interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+
+        gpio-controller;
+        #gpio-cells = <2>;
+
+        interrupt-controller;
+        #interrupt-cells = <2>;
+    };
diff --git a/Documentation/devicetree/bindings/i3c/cdns,i3c-master.yaml b/Documentation/devicetree/bindings/i3c/cdns,i3c-master.yaml
index cad6d53d0e2e..6fa3078074d0 100644
--- a/Documentation/devicetree/bindings/i3c/cdns,i3c-master.yaml
+++ b/Documentation/devicetree/bindings/i3c/cdns,i3c-master.yaml
@@ -14,7 +14,12 @@ allOf:
 
 properties:
   compatible:
-    const: cdns,i3c-master
+    oneOf:
+      - const: cdns,i3c-master
+      - items:
+          - enum:
+              - axiado,ax3000-i3c
+          - const: cdns,i3c-master
 
   reg:
     maxItems: 1
diff --git a/Documentation/devicetree/bindings/interrupt-controller/andestech,plicsw.yaml b/Documentation/devicetree/bindings/interrupt-controller/andestech,plicsw.yaml
new file mode 100644
index 000000000000..eb2eb611ac09
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/andestech,plicsw.yaml
@@ -0,0 +1,54 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/andestech,plicsw.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Andes machine-level software interrupt controller
+
+description:
+  In the Andes platform such as QiLai SoC, the PLIC module is instantiated a
+  second time with all interrupt sources tied to zero as the software interrupt
+  controller (PLIC_SW). PLIC_SW directly connects to the machine-mode
+  inter-processor interrupt lines of CPUs, so RISC-V per-CPU local interrupt
+  controller is the parent interrupt controller for PLIC_SW. PLIC_SW can
+  generate machine-mode inter-processor interrupts through programming its
+  registers.
+
+maintainers:
+  - Ben Zong-You Xie <ben717@andestech.com>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - andestech,qilai-plicsw
+      - const: andestech,plicsw
+
+  reg:
+    maxItems: 1
+
+  interrupts-extended:
+    minItems: 1
+    maxItems: 15872
+    description:
+      Specifies which harts are connected to the PLIC_SW. Each item must points
+      to a riscv,cpu-intc node, which has a riscv cpu node as parent.
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts-extended
+
+examples:
+  - |
+    interrupt-controller@400000 {
+      compatible = "andestech,qilai-plicsw", "andestech,plicsw";
+      reg = <0x400000 0x400000>;
+      interrupts-extended = <&cpu0intc 3>,
+                            <&cpu1intc 3>,
+                            <&cpu2intc 3>,
+                            <&cpu3intc 3>;
+    };
diff --git a/Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml b/Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml
index ffc4768bad06..5b827bc24301 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml
@@ -53,6 +53,7 @@ properties:
     oneOf:
       - items:
           - enum:
+              - andestech,qilai-plic
               - renesas,r9a07g043-plic
           - const: andestech,nceplic100
       - items:
diff --git a/Documentation/devicetree/bindings/mailbox/cix,sky1-mbox.yaml b/Documentation/devicetree/bindings/mailbox/cix,sky1-mbox.yaml
new file mode 100644
index 000000000000..66d75b7bc8c8
--- /dev/null
+++ b/Documentation/devicetree/bindings/mailbox/cix,sky1-mbox.yaml
@@ -0,0 +1,77 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mailbox/cix,sky1-mbox.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cixtech mailbox controller
+
+maintainers:
+  - Guomin Chen <Guomin.Chen@cixtech.com>
+
+description:
+  The Cixtech mailbox controller, used in the Cixtech Sky1 SoC,
+  is used for message transmission between multiple processors
+  within the SoC, such as the AP, PM, audio DSP, SensorHub MCU,
+  and others
+
+  Each Cixtech mailbox controller is unidirectional, so they are
+  typically used in pairs-one for receiving and one for transmitting.
+
+  Each Cixtech mailbox supports 11 channels with different transmission modes
+    channel 0-7 - Fast channel with 32bit transmit register and IRQ support
+    channel 8   - Doorbell mode,using the mailbox as an interrupt-generating
+                   mechanism.
+    channel 9   - Fifo based channel with 32*32bit depth fifo and IRQ support
+    channel 10  - Reg based channel with 32*32bit transmit register and
+                   Doorbell+transmit acknowledgment IRQ support
+
+  In the CIX Sky1 SoC use case, there are 4 pairs of mailbox controllers
+    AP <--> PM - using Doorbell transfer mode
+    AP <--> SE - using REG transfer mode
+    AP <--> DSP - using FIFO transfer mode
+    AP <--> SensorHub - using FIFO transfer mode
+
+properties:
+  compatible:
+    const: cix,sky1-mbox
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  "#mbox-cells":
+    const: 1
+
+  cix,mbox-dir:
+    $ref: /schemas/types.yaml#/definitions/string
+    description: Direction of the mailbox relative to the AP
+    enum: [tx, rx]
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#mbox-cells"
+  - cix,mbox-dir
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        mbox_ap2pm: mailbox@30000000 {
+            compatible = "cix,sky1-mbox";
+            reg = <0 0x30000000 0 0x10000>;
+            interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH 0>;
+            #mbox-cells = <1>;
+            cix,mbox-dir = "tx";
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-pxa.yaml b/Documentation/devicetree/bindings/mmc/sdhci-pxa.yaml
index 4869ddef36fd..e7c06032048a 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-pxa.yaml
+++ b/Documentation/devicetree/bindings/mmc/sdhci-pxa.yaml
@@ -30,6 +30,26 @@ allOf:
           maxItems: 1
         reg-names:
           maxItems: 1
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mrvl,pxav1-mmc
+    then:
+      properties:
+        pinctrl-names:
+          description:
+            Optional for supporting PXA168 SDIO IRQ errata to switch CMD pin between
+            SDIO CMD and GPIO mode.
+          items:
+            - const: default
+            - const: state_cmd_gpio
+        pinctrl-0:
+          description:
+            Should contain default pinctrl.
+        pinctrl-1:
+          description:
+            Should switch CMD pin to GPIO mode as a high output.
 
 properties:
   compatible:
@@ -62,22 +82,6 @@ properties:
       - const: io
       - const: core
 
-  pinctrl-names:
-    description:
-      Optional for supporting PXA168 SDIO IRQ errata to switch CMD pin between
-      SDIO CMD and GPIO mode.
-    items:
-      - const: default
-      - const: state_cmd_gpio
-
-  pinctrl-0:
-    description:
-      Should contain default pinctrl.
-
-  pinctrl-1:
-    description:
-      Should switch CMD pin to GPIO mode as a high output.
-
   mrvl,clk-delay-cycles:
     description: Specify a number of cycles to delay for tuning.
     $ref: /schemas/types.yaml#/definitions/uint32
diff --git a/Documentation/devicetree/bindings/riscv/andes.yaml b/Documentation/devicetree/bindings/riscv/andes.yaml
new file mode 100644
index 000000000000..aa1edf1fdec7
--- /dev/null
+++ b/Documentation/devicetree/bindings/riscv/andes.yaml
@@ -0,0 +1,25 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/riscv/andes.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Andes SoC-based boards
+
+maintainers:
+  - Ben Zong-You Xie <ben717@andestech.com>
+
+description:
+  Andes SoC-based boards
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - andestech,voyager
+          - const: andestech,qilai
+
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/serial/cdns,uart.yaml b/Documentation/devicetree/bindings/serial/cdns,uart.yaml
index d7f047b0bf24..9d3e5c1d8502 100644
--- a/Documentation/devicetree/bindings/serial/cdns,uart.yaml
+++ b/Documentation/devicetree/bindings/serial/cdns,uart.yaml
@@ -16,9 +16,10 @@ properties:
         items:
           - const: xlnx,xuartps
           - const: cdns,uart-r1p8
-      - description: UART controller for Zynq Ultrascale+ MPSoC
-        items:
-          - const: xlnx,zynqmp-uart
+      - items:
+          - enum:
+              - axiado,ax3000-uart
+              - xlnx,zynqmp-uart
           - const: cdns,uart-r1p12
 
   reg:
diff --git a/Documentation/devicetree/bindings/timer/andestech,plmt0.yaml b/Documentation/devicetree/bindings/timer/andestech,plmt0.yaml
new file mode 100644
index 000000000000..90b612096004
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/andestech,plmt0.yaml
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/timer/andestech,plmt0.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Andes machine-level timer
+
+description:
+  The Andes machine-level timer device (PLMT0) provides machine-level timer
+  functionality for a set of HARTs on a RISC-V platform. It has a single
+  fixed-frequency monotonic time counter (MTIME) register and a time compare
+  register (MTIMECMP) for each HART connected to the PLMT0. A timer interrupt is
+  generated if MTIME >= MTIMECMP.
+
+maintainers:
+  - Ben Zong-You Xie <ben717@andestech.com>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - andestech,qilai-plmt
+      - const: andestech,plmt0
+
+  reg:
+    maxItems: 1
+
+  interrupts-extended:
+    minItems: 1
+    maxItems: 32
+    description:
+      Specifies which harts are connected to the PLMT0. Each item must points
+      to a riscv,cpu-intc node, which has a riscv cpu node as parent. The
+      PLMT0 supports 1 hart up to 32 harts.
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts-extended
+
+examples:
+  - |
+    interrupt-controller@100000 {
+      compatible = "andestech,qilai-plmt", "andestech,plmt0";
+      reg = <0x100000 0x100000>;
+      interrupts-extended = <&cpu0intc 7>,
+                            <&cpu1intc 7>,
+                            <&cpu2intc 7>,
+                            <&cpu3intc 7>;
+    };
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 85b1e3d38024..8af7622fcb59 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -203,6 +203,8 @@ patternProperties:
     description: Shanghai Awinic Technology Co., Ltd.
   "^axentia,.*":
     description: Axentia Technologies AB
+  "^axiado,.*":
+    description: Axiado Corporation
   "^axis,.*":
     description: Axis Communications AB
   "^azoteq,.*":
@@ -309,6 +311,8 @@ patternProperties:
     description: Cirrus Logic, Inc.
   "^cisco,.*":
     description: Cisco Systems, Inc.
+  "^cix,.*":
+    description: CIX Technology Group Co., Ltd.
   "^clockwork,.*":
     description: Clockwork Tech LLC
   "^cloos,.*":
diff --git a/MAINTAINERS b/MAINTAINERS
index 254ddd29b95a..0303d65510d8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2449,6 +2449,14 @@ F:	arch/arm/boot/dts/aspeed/
 F:	arch/arm/mach-aspeed/
 N:	aspeed
 
+ARM/AXIADO ARCHITECTURE
+M:	Harshit Shah <hshah@axiado.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	Documentation/devicetree/bindings/arm/axiado.yaml
+F:	arch/arm64/boot/dts/axiado/
+N:	axiado
+
 ARM/AXM LSI SOC
 M:	Krzysztof Kozlowski <krzk@kernel.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -2508,6 +2516,19 @@ F:	arch/arm/boot/compressed/misc-ep93xx.h
 F:	arch/arm/mach-ep93xx/
 F:	drivers/iio/adc/ep93xx_adc.c
 
+ARM/CIX SOC SUPPORT
+M:	Peter Chen <peter.chen@cixtech.com>
+M:	Fugang Duan <fugang.duan@cixtech.com>
+R:	CIX Linux Kernel Upstream Group <cix-kernel-upstream@cixtech.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/cix.git
+F:	Documentation/devicetree/bindings/arm/cix.yaml
+F:	Documentation/devicetree/bindings/mailbox/cix,sky1-mbox.yaml
+F:	arch/arm64/boot/dts/cix/
+F:	drivers/mailbox/cix-mailbox.c
+K:	\bcix\b
+
 ARM/CLKDEV SUPPORT
 M:	Russell King <linux@armlinux.org.uk>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -2824,6 +2845,14 @@ F:	drivers/irqchip/irq-mvebu-*
 F:	drivers/pinctrl/mvebu/
 F:	drivers/rtc/rtc-armada38x.c
 
+ARM/Marvell PXA1908 SOC support
+M:	Duje Mihanović <duje@dujemihanovic.xyz>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	arch/arm64/boot/dts/marvell/mmp/
+F:	drivers/clk/mmp/clk-pxa1908*.c
+F:	include/dt-bindings/clock/marvell,pxa1908.h
+
 ARM/Mediatek RTC DRIVER
 M:	Eddie Huang <eddie.huang@mediatek.com>
 M:	Sean Wang <sean.wang@mediatek.com>
@@ -21379,6 +21408,15 @@ F:	drivers/irqchip/irq-riscv-intc.c
 F:	include/linux/irqchip/riscv-aplic.h
 F:	include/linux/irqchip/riscv-imsic.h
 
+RISC-V ANDES SoC Support
+M:	Ben Zong-You Xie <ben717@andestech.com>
+S:	Maintained
+T:	git: https://github.com/ben717-linux/linux
+F:	Documentation/devicetree/bindings/interrupt-controller/andestech,plicsw.yaml
+F:	Documentation/devicetree/bindings/riscv/andes.yaml
+F:	Documentation/devicetree/bindings/timer/andestech,plmt0.yaml
+F:	arch/riscv/boot/dts/andes/
+
 RISC-V ARCHITECTURE
 M:	Paul Walmsley <paul.walmsley@sifive.com>
 M:	Palmer Dabbelt <palmer@dabbelt.com>
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index a541bb029aa4..8a838c382211 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -40,6 +40,12 @@ config ARCH_APPLE
 	  This enables support for Apple's in-house ARM SoC family, such
 	  as the Apple M1.
 
+config ARCH_AXIADO
+	bool "Axiado SoC Family"
+	select GPIOLIB
+	help
+	  This enables support for Axiado SoC family like AX3000
+
 menuconfig ARCH_BCM
 	bool "Broadcom SoC Support"
 
@@ -106,6 +112,12 @@ config ARCH_BLAIZE
 	help
 	  This enables support for the Blaize SoC family
 
+config ARCH_CIX
+	bool "Cixtech SoC family"
+	help
+	  This enables support for the Cixtech SoC family,
+	  like P1(sky1).
+
 config ARCH_EXYNOS
 	bool "Samsung Exynos SoC family"
 	select COMMON_CLK_SAMSUNG
@@ -178,6 +190,14 @@ config ARCH_MESON
 	  This enables support for the arm64 based Amlogic SoCs
 	  such as the s905, S905X/D, S912, A113X/D or S905X/D2
 
+config ARCH_MMP
+	bool "Marvell MMP SoC Family"
+	select PINCTRL
+	select PINCTRL_SINGLE
+	help
+	  This enables support for Marvell MMP SoC family, currently
+	  supporting PXA1908 aka IAP140.
+
 config ARCH_MVEBU
 	bool "Marvell EBU SoC Family"
 	select ARMADA_AP806_SYSCON
@@ -307,6 +327,12 @@ config ARCH_INTEL_SOCFPGA
 	  Stratix 10 (ex. Altera), Stratix10 Software Virtual Platform,
 	  Agilex and eASIC N5X.
 
+config ARCH_SOPHGO
+	bool "Sophgo SoCs"
+	select ARCH_HAS_RESET_CONTROLLER
+	help
+	  This enables support for Sophgo SoC platform hardware.
+
 config ARCH_STM32
 	bool "STMicroelectronics STM32 SoC Family"
 	select GPIOLIB
diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile
index 79b73a21ddc2..b0844404eda1 100644
--- a/arch/arm64/boot/dts/Makefile
+++ b/arch/arm64/boot/dts/Makefile
@@ -9,10 +9,12 @@ subdir-y += amlogic
 subdir-y += apm
 subdir-y += apple
 subdir-y += arm
+subdir-y += axiado
 subdir-y += bitmain
 subdir-y += blaize
 subdir-y += broadcom
 subdir-y += cavium
+subdir-y += cix
 subdir-y += exynos
 subdir-y += freescale
 subdir-y += hisilicon
@@ -28,6 +30,7 @@ subdir-y += realtek
 subdir-y += renesas
 subdir-y += rockchip
 subdir-y += socionext
+subdir-y += sophgo
 subdir-y += sprd
 subdir-y += st
 subdir-y += synaptics
diff --git a/arch/arm64/boot/dts/axiado/Makefile b/arch/arm64/boot/dts/axiado/Makefile
new file mode 100644
index 000000000000..6676ad07db61
--- /dev/null
+++ b/arch/arm64/boot/dts/axiado/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_AXIADO) += ax3000-evk.dtb
diff --git a/arch/arm64/boot/dts/axiado/ax3000-evk.dts b/arch/arm64/boot/dts/axiado/ax3000-evk.dts
new file mode 100644
index 000000000000..92101c5b534b
--- /dev/null
+++ b/arch/arm64/boot/dts/axiado/ax3000-evk.dts
@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2021-25 Axiado Corporation (or its affiliates). All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ax3000.dtsi"
+
+/ {
+	model = "Axiado AX3000 EVK";
+	compatible = "axiado,ax3000-evk", "axiado,ax3000";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		/* Cortex-A53 will use following memory map */
+		reg = <0x00000000 0x3d000000 0x00000000 0x23000000>,
+		      <0x00000004 0x00000000 0x00000000 0x80000000>;
+	};
+};
+
+/* GPIO bank 0 - 7 */
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&gpio3 {
+	status = "okay";
+};
+
+&gpio4 {
+	status = "okay";
+};
+
+&gpio5 {
+	status = "okay";
+};
+
+&gpio6 {
+	status = "okay";
+};
+
+&gpio7 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/axiado/ax3000.dtsi b/arch/arm64/boot/dts/axiado/ax3000.dtsi
new file mode 100644
index 000000000000..792f52e0c7dd
--- /dev/null
+++ b/arch/arm64/boot/dts/axiado/ax3000.dtsi
@@ -0,0 +1,520 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2021-25 Axiado Corporation (or its affiliates). All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/memreserve/ 0x3c0013a0 0x00000008;	/* cpu-release-addr */
+/ {
+	model = "Axiado AX3000";
+	interrupt-parent = <&gic500>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0 0x0>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x3c0013a0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0 0x1>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x3c0013a0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0 0x2>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x3c0013a0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0 0x3>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x3c0013a0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-size = <0x100000>;
+			cache-unified;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
+			cache-level = <2>;
+		};
+	};
+
+	clocks {
+		clk_xin: clock-200000000 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+			clock-output-names = "clk_xin";
+		};
+
+		refclk: clock-125000000 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <125000000>;
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		ranges;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		interrupt-parent = <&gic500>;
+
+		gic500: interrupt-controller@80300000 {
+			compatible = "arm,gic-v3";
+			reg = <0x00 0x80300000 0x00 0x10000>,
+			      <0x00 0x80380000 0x00 0x80000>;
+			ranges;
+			#interrupt-cells = <3>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			interrupt-controller;
+			#redistributor-regions = <1>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		/* GPIO Controller banks 0 - 7 */
+		gpio0: gpio-controller@80500000 {
+			compatible = "axiado,ax3000-gpio", "cdns,gpio-r1p02";
+			reg = <0x00 0x80500000 0x00 0x400>;
+			clocks = <&refclk>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			status = "disabled";
+		};
+
+		gpio1: gpio-controller@80580000 {
+			compatible = "axiado,ax3000-gpio", "cdns,gpio-r1p02";
+			reg = <0x00 0x80580000 0x00 0x400>;
+			clocks = <&refclk>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			status = "disabled";
+		};
+
+		gpio2: gpio-controller@80600000 {
+			compatible = "axiado,ax3000-gpio", "cdns,gpio-r1p02";
+			reg = <0x00 0x80600000 0x00 0x400>;
+			clocks = <&refclk>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			status = "disabled";
+		};
+
+		gpio3: gpio-controller@80680000 {
+			compatible = "axiado,ax3000-gpio", "cdns,gpio-r1p02";
+			reg = <0x00 0x80680000 0x00 0x400>;
+			clocks = <&refclk>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			status = "disabled";
+		};
+
+		gpio4: gpio-controller@80700000 {
+			compatible = "axiado,ax3000-gpio", "cdns,gpio-r1p02";
+			reg = <0x00 0x80700000 0x00 0x400>;
+			clocks = <&refclk>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			status = "disabled";
+		};
+
+		gpio5: gpio-controller@80780000 {
+			compatible = "axiado,ax3000-gpio", "cdns,gpio-r1p02";
+			reg = <0x00 0x80780000 0x00 0x400>;
+			clocks = <&refclk>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			status = "disabled";
+		};
+
+		gpio6: gpio-controller@80800000 {
+			compatible = "axiado,ax3000-gpio", "cdns,gpio-r1p02";
+			reg = <0x00 0x80800000 0x00 0x400>;
+			clocks = <&refclk>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			status = "disabled";
+		};
+
+		gpio7: gpio-controller@80880000 {
+			compatible = "axiado,ax3000-gpio", "cdns,gpio-r1p02";
+			reg = <0x00 0x80880000 0x00 0x400>;
+			clocks = <&refclk>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			status = "disabled";
+		};
+
+		/* I3C Controller 0 - 16 */
+		i3c0: i3c@80500400 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80500400 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c1: i3c@80500800 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80500800 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c2: i3c@80580400 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80580400 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c3: i3c@80580800 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80580800 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c4: i3c@80600400 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80600400 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c5: i3c@80600800 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80600800 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c6: i3c@80680400 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80680400 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c7: i3c@80680800 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80680800 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c8: i3c@80700400 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80700400 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c9: i3c@80700800 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80700800 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c10: i3c@80780400 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80780400 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c11: i3c@80780800 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80780800 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c12: i3c@80800400 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80800400 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c13: i3c@80800800 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80800800 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c14: i3c@80880400 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80880400 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c15: i3c@80880800 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80880800 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i3c16: i3c@80620400 {
+			compatible = "axiado,ax3000-i3c", "cdns,i3c-master";
+			reg = <0x00 0x80620400 0x00 0x400>;
+			clocks = <&refclk &clk_xin>;
+			clock-names = "pclk", "sysclk";
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			i2c-scl-hz = <100000>;
+			i3c-scl-hz = <400000>;
+			#address-cells = <3>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		uart0: serial@80520000 {
+			compatible = "axiado,ax3000-uart", "cdns,uart-r1p12";
+			reg = <0x00 0x80520000 0x00 0x100>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "uart_clk", "pclk";
+			clocks = <&refclk &refclk>;
+			status = "disabled";
+		};
+
+		uart1: serial@805a0000 {
+			compatible = "axiado,ax3000-uart", "cdns,uart-r1p12";
+			reg = <0x00 0x805A0000 0x00 0x100>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "uart_clk", "pclk";
+			clocks = <&refclk &refclk>;
+			status = "disabled";
+		};
+
+		uart2: serial@80620000 {
+			compatible = "axiado,ax3000-uart", "cdns,uart-r1p12";
+			reg = <0x00 0x80620000 0x00 0x100>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "uart_clk", "pclk";
+			clocks = <&refclk &refclk>;
+			status = "disabled";
+		};
+
+		uart3: serial@80520800 {
+			compatible = "axiado,ax3000-uart", "cdns,uart-r1p12";
+			reg = <0x00 0x80520800 0x00 0x100>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "uart_clk", "pclk";
+			clocks = <&refclk &refclk>;
+			status = "disabled";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic500>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			   <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			   <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			   <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
diff --git a/arch/arm64/boot/dts/cix/Makefile b/arch/arm64/boot/dts/cix/Makefile
new file mode 100644
index 000000000000..ed3713982012
--- /dev/null
+++ b/arch/arm64/boot/dts/cix/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_CIX) += sky1-orion-o6.dtb
diff --git a/arch/arm64/boot/dts/cix/sky1-orion-o6.dts b/arch/arm64/boot/dts/cix/sky1-orion-o6.dts
new file mode 100644
index 000000000000..d74964d53c3b
--- /dev/null
+++ b/arch/arm64/boot/dts/cix/sky1-orion-o6.dts
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright 2025 Cix Technology Group Co., Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include "sky1.dtsi"
+/ {
+	model = "Radxa Orion O6";
+	compatible = "radxa,orion-o6", "cix,sky1";
+
+	aliases {
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x0 0x28000000>;
+			linux,cma-default;
+		};
+	};
+
+};
+
+&uart2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/cix/sky1.dtsi b/arch/arm64/boot/dts/cix/sky1.dtsi
new file mode 100644
index 000000000000..7dfe7677e649
--- /dev/null
+++ b/arch/arm64/boot/dts/cix/sky1.dtsi
@@ -0,0 +1,330 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright 2025 Cix Technology Group Co., Ltd.
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/cix,sky1.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a520";
+			enable-method = "psci";
+			reg = <0x0 0x0>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <403>;
+		};
+
+		cpu1: cpu@100 {
+			compatible = "arm,cortex-a520";
+			enable-method = "psci";
+			reg = <0x0 0x100>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <403>;
+		};
+
+		cpu2: cpu@200 {
+			compatible = "arm,cortex-a520";
+			enable-method = "psci";
+			reg = <0x0 0x200>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <403>;
+		};
+
+		cpu3: cpu@300 {
+			compatible = "arm,cortex-a520";
+			enable-method = "psci";
+			reg = <0x0 0x300>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <403>;
+		};
+
+		cpu4: cpu@400 {
+			compatible = "arm,cortex-a720";
+			enable-method = "psci";
+			reg = <0x0 0x400>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <1024>;
+		};
+
+		cpu5: cpu@500 {
+			compatible = "arm,cortex-a720";
+			enable-method = "psci";
+			reg = <0x0 0x500>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <1024>;
+		};
+
+		cpu6: cpu@600 {
+			compatible = "arm,cortex-a720";
+			enable-method = "psci";
+			reg = <0x0 0x600>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <1024>;
+		};
+
+		cpu7: cpu@700 {
+			compatible = "arm,cortex-a720";
+			enable-method = "psci";
+			reg = <0x0 0x700>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <1024>;
+		};
+
+		cpu8: cpu@800 {
+			compatible = "arm,cortex-a720";
+			enable-method = "psci";
+			reg = <0x0 0x800>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <1024>;
+		};
+
+		cpu9: cpu@900 {
+			compatible = "arm,cortex-a720";
+			enable-method = "psci";
+			reg = <0x0 0x900>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <1024>;
+		};
+
+		cpu10: cpu@a00 {
+			compatible = "arm,cortex-a720";
+			enable-method = "psci";
+			reg = <0x0 0xa00>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <1024>;
+		};
+
+		cpu11: cpu@b00 {
+			compatible = "arm,cortex-a720";
+			enable-method = "psci";
+			reg = <0x0 0xb00>;
+			device_type = "cpu";
+			capacity-dmips-mhz = <1024>;
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+				core4 {
+					cpu = <&cpu4>;
+				};
+				core5 {
+					cpu = <&cpu5>;
+				};
+				core6 {
+					cpu = <&cpu6>;
+				};
+				core7 {
+					cpu = <&cpu7>;
+				};
+				core8 {
+					cpu = <&cpu8>;
+				};
+				core9 {
+					cpu = <&cpu9>;
+				};
+				core10 {
+					cpu = <&cpu10>;
+				};
+				core11 {
+					cpu = <&cpu11>;
+				};
+			};
+		};
+	};
+
+	firmware {
+		ap_to_pm_scmi: scmi {
+			compatible = "arm,scmi";
+			mbox-names = "tx", "rx";
+			mboxes = <&mbox_ap2pm 8>, <&mbox_pm2ap 8>;
+			shmem = <&ap2pm_scmi_mem>, <&pm2ap_scmi_mem>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
+		};
+	};
+
+	pmu-a520 {
+		compatible = "arm,cortex-a520-pmu";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW &ppi_partition0>;
+	};
+
+	pmu-a720 {
+		compatible = "arm,cortex-a720-pmu";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW &ppi_partition1>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	soc@0 {
+		compatible = "simple-bus";
+		ranges = <0 0 0 0 0x20 0>;
+		dma-ranges;
+		#address-cells = <2>;
+		#size-cells = <2>;
+
+		uart0: serial@40b0000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x0 0x040b0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&scmi_clk CLK_TREE_FCH_UART0_FUNC>, <&scmi_clk CLK_TREE_FCH_UART0_APB>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart1: serial@40c0000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x0 0x040c0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&scmi_clk CLK_TREE_FCH_UART1_FUNC>, <&scmi_clk CLK_TREE_FCH_UART1_APB>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart2: serial@40d0000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x0 0x040d0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&scmi_clk CLK_TREE_FCH_UART2_FUNC>, <&scmi_clk CLK_TREE_FCH_UART2_APB>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart3: serial@40e0000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x0 0x040e0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&scmi_clk CLK_TREE_FCH_UART3_FUNC>, <&scmi_clk CLK_TREE_FCH_UART3_APB>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		mbox_ap2se: mailbox@5060000 {
+			compatible = "cix,sky1-mbox";
+			reg = <0x0 0x05060000 0x0 0x10000>;
+			interrupts = <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH 0>;
+			#mbox-cells = <1>;
+			cix,mbox-dir = "tx";
+		};
+
+		mbox_se2ap: mailbox@5070000 {
+			compatible = "cix,sky1-mbox";
+			reg = <0x0 0x05070000 0x0 0x10000>;
+			interrupts = <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH 0>;
+			#mbox-cells = <1>;
+			cix,mbox-dir = "rx";
+		};
+
+		ap2pm_scmi_mem: shmem@6590000 {
+			compatible = "arm,scmi-shmem";
+			reg = <0x0 0x06590000 0x0 0x80>;
+			reg-io-width = <4>;
+		};
+
+		mbox_ap2pm: mailbox@6590080 {
+			compatible = "cix,sky1-mbox";
+			reg = <0x0 0x06590080 0x0 0xff80>;
+			interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH 0>;
+			#mbox-cells = <1>;
+			cix,mbox-dir = "tx";
+		};
+
+		pm2ap_scmi_mem: shmem@65a0000 {
+			compatible = "arm,scmi-shmem";
+			reg = <0x0 0x065a0000 0x0 0x80>;
+			reg-io-width = <4>;
+		};
+
+		mbox_pm2ap: mailbox@65a0080 {
+			compatible = "cix,sky1-mbox";
+			reg = <0x0 0x065a0080 0x0 0xff80>;
+			interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH 0>;
+			#mbox-cells = <1>;
+			cix,mbox-dir = "rx";
+		};
+
+		mbox_sfh2ap: mailbox@8090000 {
+			compatible = "cix,sky1-mbox";
+			reg = <0x0 0x08090000 0x0 0x10000>;
+			interrupts = <GIC_SPI 391 IRQ_TYPE_LEVEL_HIGH 0>;
+			#mbox-cells = <1>;
+			cix,mbox-dir = "rx";
+		};
+
+		mbox_ap2sfh: mailbox@80a0000 {
+			compatible = "cix,sky1-mbox";
+			reg = <0x0 0x080a0000 0x0 0x10000>;
+			interrupts = <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH 0>;
+			#mbox-cells = <1>;
+			cix,mbox-dir = "tx";
+		};
+
+		gic: interrupt-controller@e010000 {
+			compatible = "arm,gic-v3";
+			reg = <0x0 0x0e010000 0 0x10000>,	/* GICD */
+			      <0x0 0x0e090000 0 0x300000>;       /* GICR * 12 */
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW 0>;
+			#interrupt-cells = <4>;
+			interrupt-controller;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			gic_its: msi-controller@e050000 {
+				compatible = "arm,gic-v3-its";
+				reg = <0x0 0x0e050000 0x0 0x30000>;
+				msi-controller;
+				#msi-cells = <1>;
+			};
+
+			ppi-partitions {
+				ppi_partition0: interrupt-partition-0 {
+					affinity = <&cpu0 &cpu1 &cpu2 &cpu3>;
+				};
+
+				ppi_partition1: interrupt-partition-1 {
+					affinity = <&cpu4 &cpu5 &cpu6 &cpu7 &cpu8 &cpu9 &cpu10 &cpu11>;
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-names = "sec-phys", "phys", "virt", "hyp-phys", "hyp-virt";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW 0>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW 0>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW 0>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW 0>,
+			     <GIC_PPI 12 IRQ_TYPE_LEVEL_LOW 0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index ce751b5028e2..40e5ac6cd468 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -32,3 +32,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-base.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-pro.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9131-cf-solidwan.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9132-clearfog.dtb
+
+subdir-y	+= mmp
diff --git a/arch/arm64/boot/dts/marvell/mmp/Makefile b/arch/arm64/boot/dts/marvell/mmp/Makefile
new file mode 100644
index 000000000000..103175ed63b0
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/mmp/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MMP) += pxa1908-samsung-coreprimevelte.dtb
diff --git a/arch/arm64/boot/dts/marvell/mmp/pxa1908-samsung-coreprimevelte.dts b/arch/arm64/boot/dts/marvell/mmp/pxa1908-samsung-coreprimevelte.dts
new file mode 100644
index 000000000000..47a4f01a7077
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/mmp/pxa1908-samsung-coreprimevelte.dts
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "pxa1908.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+	model = "Samsung Galaxy Core Prime VE LTE";
+	compatible = "samsung,coreprimevelte", "marvell,pxa1908";
+
+	aliases {
+		mmc0 = &sdh2; /* eMMC */
+		mmc1 = &sdh0; /* SD card */
+		serial0 = &uart0;
+	};
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		stdout-path = "serial0:115200n8";
+
+		fb0: framebuffer@17177000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0x17177000 0 (480 * 800 * 4)>;
+			width = <480>;
+			height = <800>;
+			stride = <(480 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	/* Bootloader fills this in */
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0 0 0>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer@17000000 {
+			reg = <0 0x17000000 0 0x1800000>;
+			no-map;
+		};
+
+		gpu@9000000 {
+			reg = <0 0x9000000 0 0x1000000>;
+		};
+
+		/* Communications processor, aka modem */
+		cp@5000000 {
+			reg = <0 0x5000000 0 0x3000000>;
+		};
+
+		cm3@a000000 {
+			reg = <0 0xa000000 0 0x80000>;
+		};
+
+		seclog@8000000 {
+			reg = <0 0x8000000 0 0x100000>;
+		};
+
+		ramoops@8100000 {
+			compatible = "ramoops";
+			reg = <0 0x8100000 0 0x40000>;
+			record-size = <0x8000>;
+			console-size = <0x20000>;
+			max-reason = <5>;
+		};
+	};
+
+	i2c-muic {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio 30 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio 29 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <3>;
+		i2c-gpio,timeout-ms = <100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_muic_pins>;
+
+		muic: extcon@14 {
+			compatible = "siliconmitus,sm5504-muic";
+			reg = <0x14>;
+			interrupt-parent = <&gpio>;
+			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pins>;
+		autorepeat;
+
+		key-home {
+			label = "Home";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpio 50 GPIO_ACTIVE_LOW>;
+		};
+
+		key-volup {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+		};
+
+		key-voldown {
+			label = "Volume Down";
+			linux,code = <KEY_VOLUMEDOWN>;
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&smmu {
+	status = "okay";
+};
+
+&pmx {
+	pinctrl-single,gpio-range = <&range 55 55 0>,
+				    <&range 110 32 0>,
+				    <&range 52 1 0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&board_pins_0 &board_pins_1 &board_pins_2>;
+
+	board_pins_0: board-pins-0 {
+		pinctrl-single,pins = <
+			0x160 0
+			0x164 0
+			0x168 0
+			0x16c 0
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0x8000 0x8000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0x8000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0x288 0x388>;
+	};
+
+	board_pins_1: board-pins-1 {
+		pinctrl-single,pins = <
+			0x44 1
+			0x48 1
+			0x20 1
+			0x18 1
+			0x14 1
+			0x10 1
+			0xc 1
+			0x8 1
+			0x68 1
+			0x58 0
+			0x54 0
+			0x7c 0
+			0x6c 0
+			0x70 0
+			0x4c 1
+			0x50 1
+			0xac 0
+			0x90 0
+			0x8c 0
+			0x88 0
+			0x84 0
+			0xc8 0
+			0x128 0
+			0x190 0
+			0x194 0
+			0x1a0 0
+			0x114 0
+			0x118 0
+			0x1d8 0
+			0x1e4 0
+			0xe8 0
+			0x100 0
+			0x204 0
+			0x210 0
+			0x218 0
+		>;
+		pinctrl-single,bias-pullup = <0xc000 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0xa000 0x8000 0xc000>;
+		pinctrl-single,low-power-mode = <0x288 0x388>;
+	};
+
+	board_pins_2: board-pins-2 {
+		pinctrl-single,pins = <
+			0x260 0
+			0x264 0
+			0x268 0
+			0x26c 0
+			0x270 0
+			0x274 0
+			0x78 0
+			0x74 0
+			0xb0 1
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	uart0_pins: uart0-pins {
+		pinctrl-single,pins = <
+			0x198 6
+			0x19c 6
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	gpio_keys_pins: gpio-keys-pins {
+		pinctrl-single,pins = <
+			0x11c 0
+			0x120 0
+			0x1a4 0
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0xc000 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0xa0000 0x8000 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	i2c_muic_pins: i2c-muic-pins {
+		pinctrl-single,pins = <
+			0x154 0
+			0x150 0
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0x288 0x388>;
+	};
+
+	sdh0_pins_0: sdh0-pins-0 {
+		pinctrl-single,pins = <
+			0x108 0
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0xc000 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0xa000 0x8000 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	sdh0_pins_1: sdh0-pins-1 {
+		pinctrl-single,pins = <
+			0x94 0
+			0x98 0
+			0x9c 0
+			0xa0 0
+			0xa4 0
+		>;
+		pinctrl-single,drive-strength = <0x800 0x1800>;
+		pinctrl-single,bias-pullup = <0xc000 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0xa000 0x8000 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	sdh0_pins_2: sdh0-pins-2 {
+		pinctrl-single,pins = <
+			0xa8 0
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0x208 0x388>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+};
+
+&twsi0 {
+	status = "okay";
+};
+
+&twsi1 {
+	status = "okay";
+};
+
+&twsi2 {
+	status = "okay";
+};
+
+&twsi3 {
+	status = "okay";
+};
+
+&usb {
+	extcon = <&muic>, <&muic>;
+};
+
+&sdh2 {
+	/* Disabled for now because initialization fails with -ETIMEDOUT. */
+	status = "disabled";
+	bus-width = <8>;
+	non-removable;
+	mmc-ddr-1_8v;
+};
+
+&sdh0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdh0_pins_0 &sdh0_pins_1 &sdh0_pins_2>;
+	cd-gpios = <&gpio 11 0>;
+	cd-inverted;
+	bus-width = <4>;
+	wp-inverted;
+};
diff --git a/arch/arm64/boot/dts/marvell/mmp/pxa1908.dtsi b/arch/arm64/boot/dts/marvell/mmp/pxa1908.dtsi
new file mode 100644
index 000000000000..cf2b9109688c
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/mmp/pxa1908.dtsi
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/marvell,pxa1908.h>
+
+/ {
+	model = "Marvell Armada PXA1908";
+	compatible = "marvell,pxa1908";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0 0>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0 1>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0 2>;
+			enable-method = "psci";
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0 3>;
+			enable-method = "psci";
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		smmu: iommu@c0010000 {
+			compatible = "arm,mmu-400";
+			reg = <0 0xc0010000 0 0x10000>;
+			#global-interrupts = <1>;
+			#iommu-cells = <1>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@d1df9000 {
+			compatible = "arm,gic-400";
+			reg = <0 0xd1df9000 0 0x1000>,
+				<0 0xd1dfa000 0 0x2000>,
+				/* The subsequent registers are guesses. */
+				<0 0xd1dfc000 0 0x2000>,
+				<0 0xd1dfe000 0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		apb@d4000000 {
+			compatible = "simple-bus";
+			reg = <0 0xd4000000 0 0x200000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xd4000000 0x200000>;
+
+			pdma: dma-controller@0 {
+				compatible = "marvell,pdma-1.0";
+				reg = <0 0x10000>;
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				dma-channels = <30>;
+				#dma-cells = <2>;
+			};
+
+			twsi1: i2c@10800 {
+				compatible = "mrvl,mmp-twsi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x10800 0x64>;
+				interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbc PXA1908_CLK_TWSI1>;
+				mrvl,i2c-fast-mode;
+				status = "disabled";
+			};
+
+			twsi0: i2c@11000 {
+				compatible = "mrvl,mmp-twsi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x11000 0x64>;
+				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbc PXA1908_CLK_TWSI0>;
+				mrvl,i2c-fast-mode;
+				status = "disabled";
+			};
+
+			twsi3: i2c@13800 {
+				compatible = "mrvl,mmp-twsi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x13800 0x64>;
+				interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbc PXA1908_CLK_TWSI3>;
+				mrvl,i2c-fast-mode;
+				status = "disabled";
+			};
+
+			apbc: clock-controller@15000 {
+				compatible = "marvell,pxa1908-apbc";
+				reg = <0x15000 0x1000>;
+				#clock-cells = <1>;
+			};
+
+			uart0: serial@17000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
+				reg = <0x17000 0x1000>;
+				interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbc PXA1908_CLK_UART0>;
+				reg-shift = <2>;
+			};
+
+			uart1: serial@18000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
+				reg = <0x18000 0x1000>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbc PXA1908_CLK_UART1>;
+				reg-shift = <2>;
+			};
+
+			gpio: gpio@19000 {
+				compatible = "marvell,mmp-gpio";
+				reg = <0x19000 0x800>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				clocks = <&apbc PXA1908_CLK_GPIO>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "gpio_mux";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ranges = <0 0x19000 0x800>;
+
+				gpio@0 {
+					reg = <0x0 0x4>;
+				};
+
+				gpio@4 {
+					reg = <0x4 0x4>;
+				};
+
+				gpio@8 {
+					reg = <0x8 0x4>;
+				};
+
+				gpio@100 {
+					reg = <0x100 0x4>;
+				};
+			};
+
+			pmx: pinmux@1e000 {
+				compatible = "marvell,pxa1908-padconf", "pinconf-single";
+				reg = <0x1e000 0x330>;
+
+				#pinctrl-cells = <1>;
+				pinctrl-single,register-width = <32>;
+				pinctrl-single,function-mask = <7>;
+
+				range: gpio-range {
+					#pinctrl-single,gpio-range-cells = <3>;
+				};
+			};
+
+			uart2: serial@36000 {
+				compatible = "mrvl,mmp-uart", "intel,xscale-uart";
+				reg = <0x36000 0x1000>;
+				interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbcp PXA1908_CLK_UART2>;
+				reg-shift = <2>;
+			};
+
+			twsi2: i2c@37000 {
+				compatible = "mrvl,mmp-twsi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x37000 0x64>;
+				interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apbcp PXA1908_CLK_TWSI2>;
+				mrvl,i2c-fast-mode;
+				status = "disabled";
+			};
+
+			apbcp: clock-controller@3b000 {
+				compatible = "marvell,pxa1908-apbcp";
+				reg = <0x3b000 0x1000>;
+				#clock-cells = <1>;
+			};
+
+			mpmu: clock-controller@50000 {
+				compatible = "marvell,pxa1908-mpmu";
+				reg = <0x50000 0x1000>;
+				#clock-cells = <1>;
+			};
+		};
+
+		axi@d4200000 {
+			compatible = "simple-bus";
+			reg = <0 0xd4200000 0 0x200000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0xd4200000 0x200000>;
+
+			usbphy: phy@7000 {
+				compatible = "marvell,pxa1928-usb-phy";
+				reg = <0x7000 0x200>;
+				clocks = <&apmu PXA1908_CLK_USB>;
+				#phy-cells = <0>;
+			};
+
+			usb: usb@8000 {
+				compatible = "chipidea,usb2";
+				reg = <0x8000 0x200>;
+				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apmu PXA1908_CLK_USB>;
+				phys = <&usbphy>;
+				phy-names = "usb-phy";
+			};
+
+			sdh0: mmc@80000 {
+				compatible = "mrvl,pxav3-mmc";
+				reg = <0x80000 0x120>;
+				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apmu PXA1908_CLK_SDH0>;
+				clock-names = "io";
+				mrvl,clk-delay-cycles = <31>;
+			};
+
+			sdh1: mmc@80800 {
+				compatible = "mrvl,pxav3-mmc";
+				reg = <0x80800 0x120>;
+				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apmu PXA1908_CLK_SDH1>;
+				clock-names = "io";
+				mrvl,clk-delay-cycles = <31>;
+			};
+
+			sdh2: mmc@81000 {
+				compatible = "mrvl,pxav3-mmc";
+				reg = <0x81000 0x120>;
+				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&apmu PXA1908_CLK_SDH2>;
+				clock-names = "io";
+				mrvl,clk-delay-cycles = <31>;
+			};
+
+			apmu: clock-controller@82800 {
+				compatible = "marvell,pxa1908-apmu";
+				reg = <0x82800 0x400>;
+				#clock-cells = <1>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/sophgo/Makefile b/arch/arm64/boot/dts/sophgo/Makefile
new file mode 100644
index 000000000000..94f52cd7d994
--- /dev/null
+++ b/arch/arm64/boot/dts/sophgo/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_SOPHGO) += sg2000-milkv-duo-module-01-evb.dtb
diff --git a/arch/arm64/boot/dts/sophgo/sg2000-milkv-duo-module-01-evb.dts b/arch/arm64/boot/dts/sophgo/sg2000-milkv-duo-module-01-evb.dts
new file mode 100644
index 000000000000..a281fee0d76e
--- /dev/null
+++ b/arch/arm64/boot/dts/sophgo/sg2000-milkv-duo-module-01-evb.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include "sg2000-milkv-duo-module-01.dtsi"
+
+/ {
+	model = "Milk-V Duo Module 01 Evaluation Board";
+	compatible = "milkv,duo-module-01-evb", "milkv,duo-module-01", "sophgo,sg2000";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&pinctrl {
+	sdhci0_cfg: sdhci0-cfg {
+		sdhci0-cd-pins {
+			pinmux = <PINMUX(PIN_SD0_CD, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <10800>;
+			power-source = <3300>;
+		};
+
+		sdhci0-clk-pins {
+			pinmux = <PINMUX(PIN_SD0_CLK, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <16100>;
+			power-source = <3300>;
+		};
+
+		sdhci0-cmd-pins {
+			pinmux = <PINMUX(PIN_SD0_CMD, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <10800>;
+			power-source = <3300>;
+		};
+
+		sdhci0-data-pins {
+			pinmux = <PINMUX(PIN_SD0_D0, 0)>,
+				 <PINMUX(PIN_SD0_D1, 0)>,
+				 <PINMUX(PIN_SD0_D2, 0)>,
+				 <PINMUX(PIN_SD0_D3, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <10800>;
+			power-source = <3300>;
+		};
+	};
+
+	uart0_cfg: uart0-cfg {
+		uart0-pins {
+			pinmux = <PINMUX(PIN_UART0_TX, 0)>,
+				 <PINMUX(PIN_UART0_RX, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <10800>;
+			power-source = <3300>;
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhci0 {
+	bus-width = <4>;
+	no-1-8-v;
+	no-mmc;
+	no-sdio;
+	disable-wp;
+	pinctrl-0 = <&sdhci0_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/sophgo/sg2000-milkv-duo-module-01.dtsi b/arch/arm64/boot/dts/sophgo/sg2000-milkv-duo-module-01.dtsi
new file mode 100644
index 000000000000..32c988f3c58f
--- /dev/null
+++ b/arch/arm64/boot/dts/sophgo/sg2000-milkv-duo-module-01.dtsi
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+#include <dt-bindings/pinctrl/pinctrl-sg2000.h>
+#include "sg2000.dtsi"
+
+/ {
+	model = "Milk-V Duo Module 01";
+	compatible = "milkv,duo-module-01", "sophgo,sg2000";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		serial4 = &uart4;
+	};
+};
+
+&osc {
+	clock-frequency = <25000000>;
+};
+
+&emmc {
+	bus-width = <4>;
+	no-1-8-v;
+	cap-mmc-hw-reset;
+	no-sd;
+	no-sdio;
+	non-removable;
+	status = "okay";
+};
+
+/* Wi-Fi */
+&sdhci1 {
+	bus-width = <4>;
+	cap-sdio-irq;
+	no-mmc;
+	no-sd;
+	non-removable;
+};
diff --git a/arch/arm64/boot/dts/sophgo/sg2000.dtsi b/arch/arm64/boot/dts/sophgo/sg2000.dtsi
new file mode 100644
index 000000000000..51177dfe9ed2
--- /dev/null
+++ b/arch/arm64/boot/dts/sophgo/sg2000.dtsi
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+#define SOC_PERIPHERAL_IRQ(nr)		GIC_SPI (nr)
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <riscv/sophgo/cv180x.dtsi>
+#include <riscv/sophgo/cv181x.dtsi>
+
+/ {
+	compatible = "sophgo,sg2000";
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0>;
+			enable-method = "psci";
+			i-cache-size = <32768>;
+			d-cache-size = <32768>;
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+			cache-size = <0x20000>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;	/* 512MiB */
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+		cpu_on = <0xc4000003>;
+		cpu_off = <0x84000002>;
+	};
+
+	soc {
+		gic: interrupt-controller@1f01000 {
+			compatible = "arm,cortex-a15-gic";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x01f01000 0x1000>,
+			      <0x01f02000 0x2000>;
+		};
+
+		pinctrl: pinctrl@3001000 {
+			compatible = "sophgo,sg2000-pinctrl";
+			reg = <0x03001000 0x1000>,
+			      <0x05027000 0x1000>;
+			reg-names = "sys", "rtc";
+		};
+
+		clk: clock-controller@3002000 {
+			compatible = "sophgo,sg2000-clk";
+			reg = <0x03002000 0x1000>;
+			clocks = <&osc>;
+			#clock-cells = <1>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+		always-on;
+		clock-frequency = <25000000>;
+	};
+};
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 91c9bf4b2ef0..d1365149776d 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -38,6 +38,7 @@ CONFIG_ARCH_AIROHA=y
 CONFIG_ARCH_SUNXI=y
 CONFIG_ARCH_ALPINE=y
 CONFIG_ARCH_APPLE=y
+CONFIG_ARCH_AXIADO=y
 CONFIG_ARCH_BCM=y
 CONFIG_ARCH_BCM2835=y
 CONFIG_ARCH_BCM_IPROC=y
@@ -45,6 +46,7 @@ CONFIG_ARCH_BCMBCA=y
 CONFIG_ARCH_BRCMSTB=y
 CONFIG_ARCH_BERLIN=y
 CONFIG_ARCH_BLAIZE=y
+CONFIG_ARCH_CIX=y
 CONFIG_ARCH_EXYNOS=y
 CONFIG_ARCH_SPARX5=y
 CONFIG_ARCH_K3=y
@@ -66,6 +68,7 @@ CONFIG_ARCH_RENESAS=y
 CONFIG_ARCH_ROCKCHIP=y
 CONFIG_ARCH_SEATTLE=y
 CONFIG_ARCH_INTEL_SOCFPGA=y
+CONFIG_ARCH_SOPHGO=y
 CONFIG_ARCH_STM32=y
 CONFIG_ARCH_SYNQUACER=y
 CONFIG_ARCH_TEGRA=y
@@ -655,6 +658,7 @@ CONFIG_PINCTRL_SM8450_LPASS_LPI=m
 CONFIG_PINCTRL_SC8280XP_LPASS_LPI=m
 CONFIG_PINCTRL_SM8550_LPASS_LPI=m
 CONFIG_PINCTRL_SM8650_LPASS_LPI=m
+CONFIG_PINCTRL_SOPHGO_SG2000=y
 CONFIG_GPIO_ALTERA=m
 CONFIG_GPIO_DAVINCI=y
 CONFIG_GPIO_DWAPB=y
@@ -1432,6 +1436,7 @@ CONFIG_QCOM_HFPLL=y
 CONFIG_CLK_GFM_LPASS_SM8250=m
 CONFIG_CLK_RCAR_USB2_CLOCK_SEL=y
 CONFIG_CLK_RENESAS_VBATTB=m
+CONFIG_CLK_SOPHGO_CV1800=y
 CONFIG_HWSPINLOCK=y
 CONFIG_HWSPINLOCK_OMAP=m
 CONFIG_HWSPINLOCK_QCOM=y
@@ -1448,6 +1453,7 @@ CONFIG_QCOM_APCS_IPC=y
 CONFIG_MTK_ADSP_MBOX=m
 CONFIG_QCOM_CPUCP_MBOX=m
 CONFIG_QCOM_IPCC=y
+CONFIG_CIX_MBOX=y
 CONFIG_ROCKCHIP_IOMMU=y
 CONFIG_TEGRA_IOMMU_SMMU=y
 CONFIG_ARM_SMMU=y
@@ -1534,6 +1540,7 @@ CONFIG_QCOM_SPMI_VADC=m
 CONFIG_QCOM_SPMI_ADC5=m
 CONFIG_ROCKCHIP_SARADC=m
 CONFIG_RZG2L_ADC=m
+CONFIG_SOPHGO_CV1800B_ADC=m
 CONFIG_TI_ADS1015=m
 CONFIG_TI_AM335X_ADC=m
 CONFIG_IIO_CROS_EC_SENSORS_CORE=m
diff --git a/arch/riscv/Kconfig.socs b/arch/riscv/Kconfig.socs
index a9c3d2f6debc..61ceae0aa27a 100644
--- a/arch/riscv/Kconfig.socs
+++ b/arch/riscv/Kconfig.socs
@@ -1,5 +1,12 @@
 menu "SoC selection"
 
+config ARCH_ANDES
+	bool "Andes SoCs"
+	depends on MMU && !XIP_KERNEL
+	select ERRATA_ANDES
+	help
+	  This enables support for Andes SoC platform hardware.
+
 config ARCH_MICROCHIP_POLARFIRE
 	def_bool ARCH_MICROCHIP
 
diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
index 64a898da9aee..3b99e91efa25 100644
--- a/arch/riscv/boot/dts/Makefile
+++ b/arch/riscv/boot/dts/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 subdir-y += allwinner
+subdir-y += andes
 subdir-y += canaan
 subdir-y += microchip
 subdir-y += renesas
diff --git a/arch/riscv/boot/dts/andes/Makefile b/arch/riscv/boot/dts/andes/Makefile
new file mode 100644
index 000000000000..c545c668ef70
--- /dev/null
+++ b/arch/riscv/boot/dts/andes/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_ANDES) += qilai-voyager.dtb
diff --git a/arch/riscv/boot/dts/andes/qilai-voyager.dts b/arch/riscv/boot/dts/andes/qilai-voyager.dts
new file mode 100644
index 000000000000..fa7d2b32a9b4
--- /dev/null
+++ b/arch/riscv/boot/dts/andes/qilai-voyager.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 Andes Technology Corporation. All rights reserved.
+ */
+
+#include "qilai.dtsi"
+
+/ {
+	model = "Voyager";
+	compatible = "andestech,voyager", "andestech,qilai";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@400000000 {
+		device_type = "memory";
+		reg = <0x4 0x00000000 0x4 0x00000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/andes/qilai.dtsi b/arch/riscv/boot/dts/andes/qilai.dtsi
new file mode 100644
index 000000000000..de3de32f8c39
--- /dev/null
+++ b/arch/riscv/boot/dts/andes/qilai.dtsi
@@ -0,0 +1,186 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2025 Andes Technology Corporation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		timebase-frequency = <62500000>;
+
+		cpu0: cpu@0 {
+			compatible = "andestech,ax45mp", "riscv";
+			device_type = "cpu";
+			reg = <0>;
+			riscv,isa-base = "rv64i";
+			riscv,isa-extensions = "i", "m", "a", "f", "d", "c",
+					       "zicntr", "zicsr", "zifencei",
+					       "zihpm", "xandespmu";
+			mmu-type = "riscv,sv39";
+			clock-frequency = <100000000>;
+			i-cache-size = <0x8000>;
+			i-cache-sets = <256>;
+			i-cache-line-size = <64>;
+			d-cache-size = <0x8000>;
+			d-cache-sets = <128>;
+			d-cache-line-size = <64>;
+			next-level-cache = <&l2_cache>;
+
+			cpu0_intc: interrupt-controller {
+				compatible = "andestech,cpu-intc", "riscv,cpu-intc";
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+
+		cpu1: cpu@1 {
+			compatible = "andestech,ax45mp", "riscv";
+			device_type = "cpu";
+			reg = <1>;
+			riscv,isa-base = "rv64i";
+			riscv,isa-extensions = "i", "m", "a", "f", "d", "c",
+					       "zicntr", "zicsr", "zifencei",
+					       "zihpm", "xandespmu";
+			mmu-type = "riscv,sv39";
+			clock-frequency = <100000000>;
+			i-cache-size = <0x8000>;
+			i-cache-sets = <256>;
+			i-cache-line-size = <64>;
+			d-cache-size = <0x8000>;
+			d-cache-sets = <128>;
+			d-cache-line-size = <64>;
+			next-level-cache = <&l2_cache>;
+
+			cpu1_intc: interrupt-controller {
+				compatible = "andestech,cpu-intc",
+					     "riscv,cpu-intc";
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+
+		cpu2: cpu@2 {
+			compatible = "andestech,ax45mp", "riscv";
+			device_type = "cpu";
+			reg = <2>;
+			riscv,isa-base = "rv64i";
+			riscv,isa-extensions = "i", "m", "a", "f", "d", "c",
+					       "zicntr", "zicsr", "zifencei",
+					       "zihpm", "xandespmu";
+			mmu-type = "riscv,sv39";
+			clock-frequency = <100000000>;
+			i-cache-size = <0x8000>;
+			i-cache-sets = <256>;
+			i-cache-line-size = <64>;
+			d-cache-size = <0x8000>;
+			d-cache-sets = <128>;
+			d-cache-line-size = <64>;
+			next-level-cache = <&l2_cache>;
+
+			cpu2_intc: interrupt-controller {
+				compatible = "andestech,cpu-intc",
+					     "riscv,cpu-intc";
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+
+		cpu3: cpu@3 {
+			compatible = "andestech,ax45mp", "riscv";
+			device_type = "cpu";
+			reg = <3>;
+			riscv,isa-base = "rv64i";
+			riscv,isa-extensions = "i", "m", "a", "f", "d", "c",
+					       "zicntr", "zicsr", "zifencei",
+					       "zihpm", "xandespmu";
+			mmu-type = "riscv,sv39";
+			clock-frequency = <100000000>;
+			i-cache-size = <0x8000>;
+			i-cache-sets = <256>;
+			i-cache-line-size = <64>;
+			d-cache-size = <0x8000>;
+			d-cache-sets = <128>;
+			d-cache-line-size = <64>;
+			next-level-cache = <&l2_cache>;
+
+			cpu3_intc: interrupt-controller {
+				compatible = "andestech,cpu-intc",
+					     "riscv,cpu-intc";
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		ranges;
+		interrupt-parent = <&plic>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+
+		plmt: timer@100000 {
+			compatible = "andestech,qilai-plmt", "andestech,plmt0";
+			reg = <0x0 0x00100000 0x0 0x100000>;
+			interrupts-extended = <&cpu0_intc 7>,
+					      <&cpu1_intc 7>,
+					      <&cpu2_intc 7>,
+					      <&cpu3_intc 7>;
+		};
+
+		l2_cache: cache-controller@200000 {
+			compatible = "andestech,qilai-ax45mp-cache",
+				     "andestech,ax45mp-cache", "cache";
+			reg = <0x0 0x00200000 0x0 0x100000>;
+			interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
+			cache-line-size = <64>;
+			cache-level = <2>;
+			cache-sets = <2048>;
+			cache-size = <0x200000>;
+			cache-unified;
+		};
+
+		plic_sw: interrupt-controller@400000 {
+			compatible = "andestech,qilai-plicsw",
+				     "andestech,plicsw";
+			reg = <0x0 0x00400000 0x0 0x400000>;
+			interrupts-extended = <&cpu0_intc 3>,
+					      <&cpu1_intc 3>,
+					      <&cpu2_intc 3>,
+					      <&cpu3_intc 3>;
+		};
+
+		plic: interrupt-controller@2000000 {
+			compatible = "andestech,qilai-plic",
+				     "andestech,nceplic100";
+			reg = <0x0 0x02000000 0x0 0x2000000>;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>,
+					      <&cpu1_intc 11>, <&cpu1_intc 9>,
+					      <&cpu2_intc 11>, <&cpu2_intc 9>,
+					      <&cpu3_intc 11>, <&cpu3_intc 9>;
+			riscv,ndev = <71>;
+		};
+
+		uart0: serial@30300000 {
+			compatible = "andestech,uart16550", "ns16550a";
+			reg = <0x0 0x30300000 0x0 0x100000>;
+			interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <50000000>;
+			reg-offset = <32>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			no-loopback-test;
+		};
+	};
+};
diff --git a/arch/riscv/configs/defconfig b/arch/riscv/configs/defconfig
index fe8bd8afb418..12f5f6ec00fa 100644
--- a/arch/riscv/configs/defconfig
+++ b/arch/riscv/configs/defconfig
@@ -22,6 +22,7 @@ CONFIG_USER_NS=y
 CONFIG_CHECKPOINT_RESTORE=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_PROFILING=y
+CONFIG_ARCH_ANDES=y
 CONFIG_ARCH_MICROCHIP=y
 CONFIG_ARCH_SIFIVE=y
 CONFIG_ARCH_SOPHGO=y
diff --git a/drivers/mailbox/Kconfig b/drivers/mailbox/Kconfig
index 68eeed660a4a..4fef4797b110 100644
--- a/drivers/mailbox/Kconfig
+++ b/drivers/mailbox/Kconfig
@@ -340,4 +340,14 @@ config THEAD_TH1520_MBOX
 	  kernel is running, and E902 core used for power management among other
 	  things.
 
+config CIX_MBOX
+        tristate "CIX Mailbox"
+        depends on ARCH_CIX || COMPILE_TEST
+        depends on OF
+        help
+          Mailbox implementation for CIX IPC system. The controller supports
+          11 mailbox channels with different operating mode and every channel
+          is unidirectional. Say Y here if you want to use the CIX Mailbox
+          support.
+
 endif
diff --git a/drivers/mailbox/Makefile b/drivers/mailbox/Makefile
index 13a3448b3271..786a46587ba1 100644
--- a/drivers/mailbox/Makefile
+++ b/drivers/mailbox/Makefile
@@ -72,3 +72,5 @@ obj-$(CONFIG_QCOM_CPUCP_MBOX)	+= qcom-cpucp-mbox.o
 obj-$(CONFIG_QCOM_IPCC)		+= qcom-ipcc.o
 
 obj-$(CONFIG_THEAD_TH1520_MBOX)	+= mailbox-th1520.o
+
+obj-$(CONFIG_CIX_MBOX)	+= cix-mailbox.o
diff --git a/drivers/mailbox/cix-mailbox.c b/drivers/mailbox/cix-mailbox.c
new file mode 100644
index 000000000000..5bb1416c26a5
--- /dev/null
+++ b/drivers/mailbox/cix-mailbox.c
@@ -0,0 +1,645 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2025 Cix Technology Group Co., Ltd.
+ */
+
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mailbox_controller.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include "mailbox.h"
+
+/*
+ * The maximum transmission size is 32 words or 128 bytes.
+ */
+#define CIX_MBOX_MSG_WORDS	32	/* Max length = 32 words */
+#define CIX_MBOX_MSG_LEN_MASK	0x7fL	/* Max length = 128 bytes */
+
+/* [0~7] Fast channel
+ * [8] doorbell base channel
+ * [9]fifo base channel
+ * [10] register base channel
+ */
+#define CIX_MBOX_FAST_IDX	7
+#define CIX_MBOX_DB_IDX		8
+#define CIX_MBOX_FIFO_IDX	9
+#define CIX_MBOX_REG_IDX	10
+#define CIX_MBOX_CHANS	11
+
+/* Register define */
+#define CIX_REG_MSG(n)	(0x0 + 0x4*(n))			/* 0x0~0x7c */
+#define CIX_REG_DB_ACK	CIX_REG_MSG(CIX_MBOX_MSG_WORDS)	/* 0x80 */
+#define CIX_ERR_COMP	(CIX_REG_DB_ACK + 0x4)		/* 0x84 */
+#define CIX_ERR_COMP_CLR	(CIX_REG_DB_ACK + 0x8)		/* 0x88 */
+#define CIX_REG_F_INT(IDX)	(CIX_ERR_COMP_CLR + 0x4*(IDX+1))	/* 0x8c~0xa8 */
+#define CIX_FIFO_WR		(CIX_REG_F_INT(CIX_MBOX_FAST_IDX+1))	/* 0xac */
+#define CIX_FIFO_RD		(CIX_FIFO_WR + 0x4)			/* 0xb0 */
+#define CIX_FIFO_STAS	(CIX_FIFO_WR + 0x8)			/* 0xb4 */
+#define CIX_FIFO_WM		(CIX_FIFO_WR + 0xc)			/* 0xb8 */
+#define CIX_INT_ENABLE	(CIX_FIFO_WR + 0x10)		/* 0xbc */
+#define CIX_INT_ENABLE_SIDE_B	(CIX_FIFO_WR + 0x14)	/* 0xc0 */
+#define CIX_INT_CLEAR	(CIX_FIFO_WR + 0x18)		/* 0xc4 */
+#define CIX_INT_STATUS	(CIX_FIFO_WR + 0x1c)		/* 0xc8 */
+#define CIX_FIFO_RST	(CIX_FIFO_WR + 0x20)		/* 0xcc */
+
+#define CIX_MBOX_TX		0
+#define CIX_MBOX_RX		1
+
+#define CIX_DB_INT_BIT	BIT(0)
+#define CIX_DB_ACK_INT_BIT	BIT(1)
+
+#define CIX_FIFO_WM_DEFAULT		CIX_MBOX_MSG_WORDS
+#define CIX_FIFO_STAS_WMK		BIT(0)
+#define CIX_FIFO_STAS_FULL		BIT(1)
+#define CIX_FIFO_STAS_EMPTY		BIT(2)
+#define CIX_FIFO_STAS_UFLOW		BIT(3)
+#define CIX_FIFO_STAS_OFLOW		BIT(4)
+
+#define CIX_FIFO_RST_BIT		BIT(0)
+
+#define CIX_DB_INT			BIT(0)
+#define CIX_ACK_INT			BIT(1)
+#define CIX_FIFO_FULL_INT		BIT(2)
+#define CIX_FIFO_EMPTY_INT		BIT(3)
+#define CIX_FIFO_WM01_INT		BIT(4)
+#define CIX_FIFO_WM10_INT		BIT(5)
+#define CIX_FIFO_OFLOW_INT		BIT(6)
+#define CIX_FIFO_UFLOW_INT		BIT(7)
+#define CIX_FIFO_N_EMPTY_INT	BIT(8)
+#define CIX_FAST_CH_INT(IDX)	BIT((IDX)+9)
+
+#define CIX_SHMEM_OFFSET 0x80
+
+enum cix_mbox_chan_type {
+	CIX_MBOX_TYPE_DB,
+	CIX_MBOX_TYPE_REG,
+	CIX_MBOX_TYPE_FIFO,
+	CIX_MBOX_TYPE_FAST,
+};
+
+struct cix_mbox_con_priv {
+	enum cix_mbox_chan_type type;
+	struct mbox_chan	*chan;
+	int index;
+};
+
+struct cix_mbox_priv {
+	struct device *dev;
+	int irq;
+	int dir;
+	void __iomem *base;	/* region for mailbox */
+	struct cix_mbox_con_priv con_priv[CIX_MBOX_CHANS];
+	struct mbox_chan mbox_chans[CIX_MBOX_CHANS];
+	struct mbox_controller mbox;
+	bool use_shmem;
+};
+
+/*
+ * The CIX mailbox supports four types of transfers:
+ * CIX_MBOX_TYPE_DB, CIX_MBOX_TYPE_FAST, CIX_MBOX_TYPE_REG, and CIX_MBOX_TYPE_FIFO.
+ * For the REG and FIFO types of transfers, the message format is as follows:
+ */
+union cix_mbox_msg_reg_fifo {
+	u32 length;	/* unit is byte */
+	u32 buf[CIX_MBOX_MSG_WORDS]; /* buf[0] must be the byte length of this array */
+};
+
+static struct cix_mbox_priv *to_cix_mbox_priv(struct mbox_controller *mbox)
+{
+	return container_of(mbox, struct cix_mbox_priv, mbox);
+}
+
+static void cix_mbox_write(struct cix_mbox_priv *priv, u32 val, u32 offset)
+{
+	if (priv->use_shmem)
+		iowrite32(val, priv->base + offset - CIX_SHMEM_OFFSET);
+	else
+		iowrite32(val, priv->base + offset);
+}
+
+static u32 cix_mbox_read(struct cix_mbox_priv *priv, u32 offset)
+{
+	if (priv->use_shmem)
+		return ioread32(priv->base + offset - CIX_SHMEM_OFFSET);
+	else
+		return ioread32(priv->base + offset);
+}
+
+static bool mbox_fifo_empty(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+
+	return ((cix_mbox_read(priv, CIX_FIFO_STAS) & CIX_FIFO_STAS_EMPTY) ? true : false);
+}
+
+/*
+ *The transmission unit of the CIX mailbox is word.
+ *The byte length should be converted into the word length.
+ */
+static inline u32 mbox_get_msg_size(void *msg)
+{
+	u32 len;
+
+	len = ((u32 *)msg)[0] & CIX_MBOX_MSG_LEN_MASK;
+	return DIV_ROUND_UP(len, 4);
+}
+
+static int cix_mbox_send_data_db(struct mbox_chan *chan, void *data)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+
+	/* trigger doorbell irq */
+	cix_mbox_write(priv, CIX_DB_INT_BIT, CIX_REG_DB_ACK);
+
+	return 0;
+}
+
+static int cix_mbox_send_data_reg(struct mbox_chan *chan, void *data)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	union cix_mbox_msg_reg_fifo *msg = data;
+	u32 len, i;
+
+	if (!data)
+		return -EINVAL;
+
+	len = mbox_get_msg_size(data);
+	for (i = 0; i < len; i++)
+		cix_mbox_write(priv, msg->buf[i], CIX_REG_MSG(i));
+
+	/* trigger doorbell irq */
+	cix_mbox_write(priv, CIX_DB_INT_BIT, CIX_REG_DB_ACK);
+
+	return 0;
+}
+
+static int cix_mbox_send_data_fifo(struct mbox_chan *chan, void *data)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	union cix_mbox_msg_reg_fifo *msg = data;
+	u32 len, val, i;
+
+	if (!data)
+		return -EINVAL;
+
+	len = mbox_get_msg_size(data);
+	cix_mbox_write(priv, len, CIX_FIFO_WM);
+	for (i = 0; i < len; i++)
+		cix_mbox_write(priv, msg->buf[i], CIX_FIFO_WR);
+
+	/* Enable fifo empty interrupt */
+	val = cix_mbox_read(priv, CIX_INT_ENABLE);
+	val |= CIX_FIFO_EMPTY_INT;
+	cix_mbox_write(priv, val, CIX_INT_ENABLE);
+
+	return 0;
+}
+
+static int cix_mbox_send_data_fast(struct mbox_chan *chan, void *data)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+	u32 *arg = (u32 *)data;
+	int index = cp->index;
+
+	if (!data)
+		return -EINVAL;
+
+	if (index < 0 || index > CIX_MBOX_FAST_IDX) {
+		dev_err(priv->dev, "Invalid Mbox index %d\n", index);
+		return -EINVAL;
+	}
+
+	cix_mbox_write(priv, arg[0], CIX_REG_F_INT(index));
+
+	return 0;
+}
+
+static int cix_mbox_send_data(struct mbox_chan *chan, void *data)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+
+	if (priv->dir != CIX_MBOX_TX) {
+		dev_err(priv->dev, "Invalid Mbox dir %d\n", priv->dir);
+		return -EINVAL;
+	}
+
+	switch (cp->type) {
+	case CIX_MBOX_TYPE_DB:
+		cix_mbox_send_data_db(chan, data);
+		break;
+	case CIX_MBOX_TYPE_REG:
+		cix_mbox_send_data_reg(chan, data);
+		break;
+	case CIX_MBOX_TYPE_FIFO:
+		cix_mbox_send_data_fifo(chan, data);
+		break;
+	case CIX_MBOX_TYPE_FAST:
+		cix_mbox_send_data_fast(chan, data);
+		break;
+	default:
+		dev_err(priv->dev, "Invalid channel type: %d\n", cp->type);
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static void cix_mbox_isr_db(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	u32 int_status;
+
+	int_status = cix_mbox_read(priv, CIX_INT_STATUS);
+
+	if (priv->dir == CIX_MBOX_RX) {
+		/* rx interrupt is triggered */
+		if (int_status & CIX_DB_INT) {
+			cix_mbox_write(priv, CIX_DB_INT, CIX_INT_CLEAR);
+			mbox_chan_received_data(chan, NULL);
+			/* trigger ack interrupt */
+			cix_mbox_write(priv, CIX_DB_ACK_INT_BIT, CIX_REG_DB_ACK);
+		}
+	} else {
+		/* tx ack interrupt is triggered */
+		if (int_status & CIX_ACK_INT) {
+			cix_mbox_write(priv, CIX_ACK_INT, CIX_INT_CLEAR);
+			mbox_chan_received_data(chan, NULL);
+		}
+	}
+}
+
+static void cix_mbox_isr_reg(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	u32 int_status;
+
+	int_status = cix_mbox_read(priv, CIX_INT_STATUS);
+
+	if (priv->dir == CIX_MBOX_RX) {
+		/* rx interrupt is triggered */
+		if (int_status & CIX_DB_INT) {
+			u32 data[CIX_MBOX_MSG_WORDS], len, i;
+
+			cix_mbox_write(priv, CIX_DB_INT, CIX_INT_CLEAR);
+			data[0] = cix_mbox_read(priv, CIX_REG_MSG(0));
+			len = mbox_get_msg_size(data);
+			for (i = 1; i < len; i++)
+				data[i] = cix_mbox_read(priv, CIX_REG_MSG(i));
+
+			/* trigger ack interrupt */
+			cix_mbox_write(priv, CIX_DB_ACK_INT_BIT, CIX_REG_DB_ACK);
+			mbox_chan_received_data(chan, data);
+		}
+	} else {
+		/* tx ack interrupt is triggered */
+		if (int_status & CIX_ACK_INT) {
+			cix_mbox_write(priv, CIX_ACK_INT, CIX_INT_CLEAR);
+			mbox_chan_txdone(chan, 0);
+		}
+	}
+}
+
+static void cix_mbox_isr_fifo(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	u32 int_status, status;
+
+	int_status = cix_mbox_read(priv, CIX_INT_STATUS);
+
+	if (priv->dir == CIX_MBOX_RX) {
+		/* FIFO waterMark interrupt is generated */
+		if (int_status & (CIX_FIFO_FULL_INT | CIX_FIFO_WM01_INT)) {
+			u32 data[CIX_MBOX_MSG_WORDS] = { 0 }, i = 0;
+
+			cix_mbox_write(priv, (CIX_FIFO_FULL_INT | CIX_FIFO_WM01_INT),
+						CIX_INT_CLEAR);
+			do {
+				data[i++] = cix_mbox_read(priv, CIX_FIFO_RD);
+			} while (!mbox_fifo_empty(chan) && i < CIX_MBOX_MSG_WORDS);
+
+			mbox_chan_received_data(chan, data);
+		}
+		/* FIFO underflow is generated */
+		if (int_status & CIX_FIFO_UFLOW_INT) {
+			status = cix_mbox_read(priv, CIX_FIFO_STAS);
+			dev_err(priv->dev, "fifo underflow: int_stats %d\n", status);
+			cix_mbox_write(priv, CIX_FIFO_UFLOW_INT, CIX_INT_CLEAR);
+		}
+	} else {
+		/* FIFO empty interrupt is generated */
+		if (int_status & CIX_FIFO_EMPTY_INT) {
+			u32 val;
+
+			cix_mbox_write(priv, CIX_FIFO_EMPTY_INT, CIX_INT_CLEAR);
+			/* Disable empty irq*/
+			val = cix_mbox_read(priv, CIX_INT_ENABLE);
+			val &= ~CIX_FIFO_EMPTY_INT;
+			cix_mbox_write(priv, val, CIX_INT_ENABLE);
+			mbox_chan_txdone(chan, 0);
+		}
+		/* FIFO overflow is generated */
+		if (int_status & CIX_FIFO_OFLOW_INT) {
+			status = cix_mbox_read(priv, CIX_FIFO_STAS);
+			dev_err(priv->dev, "fifo overlow: int_stats %d\n", status);
+			cix_mbox_write(priv, CIX_FIFO_OFLOW_INT, CIX_INT_CLEAR);
+		}
+	}
+}
+
+static void cix_mbox_isr_fast(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+	u32 int_status, data;
+
+	/* no irq will be trigger for TX dir mbox */
+	if (priv->dir != CIX_MBOX_RX)
+		return;
+
+	int_status = cix_mbox_read(priv, CIX_INT_STATUS);
+
+	if (int_status & CIX_FAST_CH_INT(cp->index)) {
+		cix_mbox_write(priv, CIX_FAST_CH_INT(cp->index), CIX_INT_CLEAR);
+		data = cix_mbox_read(priv, CIX_REG_F_INT(cp->index));
+		mbox_chan_received_data(chan, &data);
+	}
+}
+
+static irqreturn_t cix_mbox_isr(int irq, void *arg)
+{
+	struct mbox_chan *chan = arg;
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+
+	switch (cp->type) {
+	case CIX_MBOX_TYPE_DB:
+		cix_mbox_isr_db(chan);
+		break;
+	case CIX_MBOX_TYPE_REG:
+		cix_mbox_isr_reg(chan);
+		break;
+	case CIX_MBOX_TYPE_FIFO:
+		cix_mbox_isr_fifo(chan);
+		break;
+	case CIX_MBOX_TYPE_FAST:
+		cix_mbox_isr_fast(chan);
+		break;
+	default:
+		dev_err(priv->dev, "Invalid channel type: %d\n", cp->type);
+		return IRQ_NONE;
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int cix_mbox_startup(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+	int index = cp->index, ret;
+	u32 val;
+
+	ret = request_irq(priv->irq, cix_mbox_isr, 0,
+			  dev_name(priv->dev), chan);
+	if (ret) {
+		dev_err(priv->dev, "Unable to acquire IRQ %d\n", priv->irq);
+		return ret;
+	}
+
+	switch (cp->type) {
+	case CIX_MBOX_TYPE_DB:
+		/* Overwrite txdone_method for DB channel */
+		chan->txdone_method = TXDONE_BY_ACK;
+		fallthrough;
+	case CIX_MBOX_TYPE_REG:
+		if (priv->dir == CIX_MBOX_TX) {
+			/* Enable ACK interrupt */
+			val = cix_mbox_read(priv, CIX_INT_ENABLE);
+			val |= CIX_ACK_INT;
+			cix_mbox_write(priv, val, CIX_INT_ENABLE);
+		} else {
+			/* Enable Doorbell interrupt */
+			val = cix_mbox_read(priv, CIX_INT_ENABLE_SIDE_B);
+			val |= CIX_DB_INT;
+			cix_mbox_write(priv, val, CIX_INT_ENABLE_SIDE_B);
+		}
+		break;
+	case CIX_MBOX_TYPE_FIFO:
+		/* reset fifo */
+		cix_mbox_write(priv, CIX_FIFO_RST_BIT, CIX_FIFO_RST);
+		/* set default watermark */
+		cix_mbox_write(priv, CIX_FIFO_WM_DEFAULT, CIX_FIFO_WM);
+		if (priv->dir == CIX_MBOX_TX) {
+			/* Enable fifo overflow interrupt */
+			val = cix_mbox_read(priv, CIX_INT_ENABLE);
+			val |= CIX_FIFO_OFLOW_INT;
+			cix_mbox_write(priv, val, CIX_INT_ENABLE);
+		} else {
+			/* Enable fifo full/underflow interrupt */
+			val = cix_mbox_read(priv, CIX_INT_ENABLE_SIDE_B);
+			val |= CIX_FIFO_UFLOW_INT|CIX_FIFO_WM01_INT;
+			cix_mbox_write(priv, val, CIX_INT_ENABLE_SIDE_B);
+		}
+		break;
+	case CIX_MBOX_TYPE_FAST:
+		/* Only RX channel has intterupt */
+		if (priv->dir == CIX_MBOX_RX) {
+			if (index < 0 || index > CIX_MBOX_FAST_IDX) {
+				dev_err(priv->dev, "Invalid index %d\n", index);
+				ret = -EINVAL;
+				goto failed;
+			}
+			/* enable fast channel interrupt */
+			val = cix_mbox_read(priv, CIX_INT_ENABLE_SIDE_B);
+			val |= CIX_FAST_CH_INT(index);
+			cix_mbox_write(priv, val, CIX_INT_ENABLE_SIDE_B);
+		}
+		break;
+	default:
+		dev_err(priv->dev, "Invalid channel type: %d\n", cp->type);
+		ret = -EINVAL;
+		goto failed;
+	}
+	return 0;
+
+failed:
+	free_irq(priv->irq, chan);
+	return ret;
+}
+
+static void cix_mbox_shutdown(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+	int index = cp->index;
+	u32 val;
+
+	switch (cp->type) {
+	case CIX_MBOX_TYPE_DB:
+	case CIX_MBOX_TYPE_REG:
+		if (priv->dir == CIX_MBOX_TX) {
+			/* Disable ACK interrupt */
+			val = cix_mbox_read(priv, CIX_INT_ENABLE);
+			val &= ~CIX_ACK_INT;
+			cix_mbox_write(priv, val, CIX_INT_ENABLE);
+		} else if (priv->dir == CIX_MBOX_RX) {
+			/* Disable Doorbell interrupt */
+			val = cix_mbox_read(priv, CIX_INT_ENABLE_SIDE_B);
+			val &= ~CIX_DB_INT;
+			cix_mbox_write(priv, val, CIX_INT_ENABLE_SIDE_B);
+		}
+		break;
+	case CIX_MBOX_TYPE_FIFO:
+		if (priv->dir == CIX_MBOX_TX) {
+			/* Disable empty/fifo overflow irq*/
+			val = cix_mbox_read(priv, CIX_INT_ENABLE);
+			val &= ~(CIX_FIFO_EMPTY_INT | CIX_FIFO_OFLOW_INT);
+			cix_mbox_write(priv, val, CIX_INT_ENABLE);
+		} else if (priv->dir == CIX_MBOX_RX) {
+			/* Disable fifo WM01/underflow interrupt */
+			val = cix_mbox_read(priv, CIX_INT_ENABLE_SIDE_B);
+			val &= ~(CIX_FIFO_UFLOW_INT | CIX_FIFO_WM01_INT);
+			cix_mbox_write(priv, val, CIX_INT_ENABLE_SIDE_B);
+		}
+		break;
+	case CIX_MBOX_TYPE_FAST:
+		if (priv->dir == CIX_MBOX_RX) {
+			if (index < 0 || index > CIX_MBOX_FAST_IDX) {
+				dev_err(priv->dev, "Invalid index %d\n", index);
+				break;
+			}
+			/* Disable fast channel interrupt */
+			val = cix_mbox_read(priv, CIX_INT_ENABLE_SIDE_B);
+			val &= ~CIX_FAST_CH_INT(index);
+			cix_mbox_write(priv, val, CIX_INT_ENABLE_SIDE_B);
+		}
+		break;
+
+	default:
+		dev_err(priv->dev, "Invalid channel type: %d\n", cp->type);
+		break;
+	}
+
+	free_irq(priv->irq, chan);
+}
+
+static const struct mbox_chan_ops cix_mbox_chan_ops = {
+	.send_data = cix_mbox_send_data,
+	.startup = cix_mbox_startup,
+	.shutdown = cix_mbox_shutdown,
+};
+
+static void cix_mbox_init(struct cix_mbox_priv *priv)
+{
+	struct cix_mbox_con_priv *cp;
+	int i;
+
+	for (i = 0; i < CIX_MBOX_CHANS; i++) {
+		cp = &priv->con_priv[i];
+		cp->index = i;
+		cp->chan = &priv->mbox_chans[i];
+		priv->mbox_chans[i].con_priv = cp;
+		if (cp->index <= CIX_MBOX_FAST_IDX)
+			cp->type = CIX_MBOX_TYPE_FAST;
+		if (cp->index == CIX_MBOX_DB_IDX)
+			cp->type = CIX_MBOX_TYPE_DB;
+		if (cp->index == CIX_MBOX_FIFO_IDX)
+			cp->type = CIX_MBOX_TYPE_FIFO;
+		if (cp->index == CIX_MBOX_REG_IDX)
+			cp->type = CIX_MBOX_TYPE_REG;
+	}
+}
+
+static int cix_mbox_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct cix_mbox_priv *priv;
+	struct resource *res;
+	const char *dir_str;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = dev;
+	priv->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	/*
+	 * The first 0x80 bytes of the register space of the cix mailbox controller
+	 * can be used as shared memory for clients. When this shared memory is in
+	 * use, the base address of the mailbox is offset by 0x80. Therefore, when
+	 * performing subsequent read/write operations, it is necessary to subtract
+	 * the offset CIX_SHMEM_OFFSET.
+	 *
+	 * When the base address of the mailbox is offset by 0x80, it indicates
+	 * that shmem is in use.
+	 */
+	priv->use_shmem = !!(res->start & CIX_SHMEM_OFFSET);
+
+	priv->irq = platform_get_irq(pdev, 0);
+	if (priv->irq < 0)
+		return priv->irq;
+
+	if (device_property_read_string(dev, "cix,mbox-dir", &dir_str)) {
+		dev_err(priv->dev, "cix,mbox_dir property not found\n");
+		return -EINVAL;
+	}
+
+	if (!strcmp(dir_str, "tx"))
+		priv->dir = 0;
+	else if (!strcmp(dir_str, "rx"))
+		priv->dir = 1;
+	else {
+		dev_err(priv->dev, "cix,mbox_dir=%s is not expected\n", dir_str);
+		return -EINVAL;
+	}
+
+	cix_mbox_init(priv);
+
+	priv->mbox.dev = dev;
+	priv->mbox.ops = &cix_mbox_chan_ops;
+	priv->mbox.chans = priv->mbox_chans;
+	priv->mbox.txdone_irq = true;
+	priv->mbox.num_chans = CIX_MBOX_CHANS;
+	priv->mbox.of_xlate = NULL;
+
+	platform_set_drvdata(pdev, priv);
+	ret = devm_mbox_controller_register(dev, &priv->mbox);
+	if (ret)
+		dev_err(dev, "Failed to register mailbox %d\n", ret);
+
+	return ret;
+}
+
+static const struct of_device_id cix_mbox_dt_ids[] = {
+	{ .compatible = "cix,sky1-mbox" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, cix_mbox_dt_ids);
+
+static struct platform_driver cix_mbox_driver = {
+	.probe = cix_mbox_probe,
+	.driver = {
+		.name = "cix_mbox",
+		.of_match_table = cix_mbox_dt_ids,
+	},
+};
+
+static int __init cix_mailbox_init(void)
+{
+	return platform_driver_register(&cix_mbox_driver);
+}
+arch_initcall(cix_mailbox_init);
+
+MODULE_AUTHOR("Cix Technology Group Co., Ltd.");
+MODULE_DESCRIPTION("CIX mailbox driver");
+MODULE_LICENSE("GPL");
diff --git a/include/dt-bindings/clock/cix,sky1.h b/include/dt-bindings/clock/cix,sky1.h
new file mode 100644
index 000000000000..9245ebd1e80a
--- /dev/null
+++ b/include/dt-bindings/clock/cix,sky1.h
@@ -0,0 +1,279 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright 2024-2025 Cix Technology Group Co., Ltd.
+ */
+
+#ifndef _DT_BINDINGS_CLK_CIX_SKY1_H
+#define _DT_BINDINGS_CLK_CIX_SKY1_H
+
+#define CLK_TREE_CPU_GICxCLK			0
+#define CLK_TREE_CPU_PPUCLK			1
+#define CLK_TREE_CPU_PERIPHCLK			2
+#define CLK_TREE_DSU_CLK			3
+#define CLK_TREE_DSU_PCLK			4
+#define CLK_TREE_CPU_CLK_BC0			5
+#define CLK_TREE_CPU_CLK_BC1			6
+#define CLK_TREE_CPU_CLK_BC2			7
+#define CLK_TREE_CPU_CLK_BC3			8
+#define CLK_TREE_CPU_CLK_MC0			9
+#define CLK_TREE_CPU_CLK_MC1			10
+#define CLK_TREE_CPU_CLK_MC2			11
+#define CLK_TREE_CPU_CLK_MC3			12
+#define CLK_TREE_CPU_CLK_LC0			13
+#define CLK_TREE_CPU_CLK_LC1			14
+#define CLK_TREE_CPU_CLK_LC2			15
+#define CLK_TREE_CPU_CLK_LC3			16
+#define CLK_TREE_CSI_CTRL0_PCLK			17
+#define CLK_TREE_CSI_CTRL1_PCLK			18
+#define CLK_TREE_CSI_CTRL2_PCLK			19
+#define CLK_TREE_CSI_CTRL3_PCLK			20
+#define CLK_TREE_CSI_DMA0_PCLK			21
+#define CLK_TREE_CSI_DMA1_PCLK			22
+#define CLK_TREE_CSI_DMA2_PCLK			23
+#define CLK_TREE_CSI_DMA3_PCLK			24
+#define CLK_TREE_CSI_PHY0_PSM			25
+#define CLK_TREE_CSI_PHY1_PSM			26
+#define CLK_TREE_CSI_PHY0_APBCLK		27
+#define CLK_TREE_CSI_PHY1_APBCLK		28
+#define CLK_TREE_FCH_APB_CLK			29
+#define CLK_TREE_GPU_CLK_400M			30
+#define CLK_TREE_GPU_CLK_CORE			31
+#define CLK_TREE_GPU_CLK_STACKS			32
+#define CLK_TREE_DP0_PIXEL0			33
+#define CLK_TREE_DP0_PIXEL1			34
+#define CLK_TREE_DP1_PIXEL0			35
+#define CLK_TREE_DP1_PIXEL1			36
+#define CLK_TREE_DP2_PIXEL0			37
+#define CLK_TREE_DP2_PIXEL1			38
+#define CLK_TREE_DP3_PIXEL0			39
+#define CLK_TREE_DP3_PIXEL1			40
+#define CLK_TREE_DP4_PIXEL0			41
+#define CLK_TREE_DP4_PIXEL1			42
+#define CLK_TREE_DPU_CLK			43
+#define CLK_TREE_DPU0_ACLK			44
+#define CLK_TREE_DPU1_ACLK			45
+#define CLK_TREE_DPU2_ACLK			46
+#define CLK_TREE_DPU3_ACLK			47
+#define CLK_TREE_DPU4_ACLK			48
+#define CLK_TREE_DPC0_VIDCLK0			49
+#define CLK_TREE_DPC0_VIDCLK1			50
+#define CLK_TREE_DPC1_VIDCLK0			51
+#define CLK_TREE_DPC1_VIDCLK1			52
+#define CLK_TREE_DPC2_VIDCLK0			53
+#define CLK_TREE_DPC2_VIDCLK1			54
+#define CLK_TREE_DPC3_VIDCLK0			55
+#define CLK_TREE_DPC3_VIDCLK1			56
+#define CLK_TREE_DPC4_VIDCLK0			57
+#define CLK_TREE_DPC4_VIDCLK1			58
+#define CLK_TREE_DPC0_APBCLK			59
+#define CLK_TREE_DPC1_APBCLK			60
+#define CLK_TREE_DPC2_APBCLK			61
+#define CLK_TREE_DPC3_APBCLK			62
+#define CLK_TREE_DPC4_APBCLK			63
+#define CLK_TREE_NPU_MEMCLK			64
+#define CLK_TREE_NPU_SYSCLK			65
+#define CLK_TREE_NPU_DBGCLK			66
+#define CLK_TREE_VPU_APBCLK			67
+#define CLK_TREE_ISP_ACLK			68
+#define CLK_TREE_ISP_SCLK			69
+#define CLK_TREE_AUDIO_CLK4			70
+#define CLK_TREE_AUDIO_CLK5			71
+#define CLK_TREE_CAMERA_MCLK0			72
+#define CLK_TREE_CAMERA_MCLK1			73
+#define CLK_TREE_CAMERA_MCLK2			74
+#define CLK_TREE_CAMERA_MCLK3			75
+#define CLK_TREE_AUDIO_CLK0			76
+#define CLK_TREE_AUDIO_CLK1			77
+#define CLK_TREE_AUDIO_CLK2			78
+#define CLK_TREE_AUDIO_CLK3			79
+#define CLK_TREE_MM_NI700_CLK			80
+#define CLK_TREE_SYS_NI700_CLK			81
+#define CLK_TREE_GMAC0_ACLK			82
+#define CLK_TREE_GMAC1_ACLK			83
+#define CLK_TREE_GMAC0_DIV_ACLK			84
+#define CLK_TREE_GMAC0_DIV_TXCLK		85
+#define CLK_TREE_GMAC0_RGMII0_TXCLK		86
+#define CLK_TREE_GMAC1_DIV_ACLK			87
+#define CLK_TREE_GMAC1_DIV_TXCLK		88
+#define CLK_TREE_GMAC1_RGMII0_TXCLK		89
+#define CLK_TREE_GMAC0_PCLK			90
+#define CLK_TREE_GMAC1_PCLK			91
+#define CLK_TREE_USB2_0_AXI_GATE		92
+#define CLK_TREE_USB2_0_APB_GATE		93
+#define CLK_TREE_USB2_1_AXI_GATE		94
+#define CLK_TREE_USB2_1_APB_GATE		95
+#define CLK_TREE_USB2_2_AXI_GATE		96
+#define CLK_TREE_USB2_2_APB_GATE		97
+#define CLK_TREE_USB2_3_AXI_GATE		98
+#define CLK_TREE_USB2_3_APB_GATE		99
+#define CLK_TREE_USB2_0_PHY_GATE		100
+#define CLK_TREE_USB2_1_PHY_GATE		101
+#define CLK_TREE_USB2_2_PHY_GATE		102
+#define CLK_TREE_USB2_3_PHY_GATE		103
+#define CLK_TREE_USB3C_DRD_AXI_GATE		104
+#define CLK_TREE_USB3C_DRD_APB_GATE		105
+#define CLK_TREE_USB3C_DRD_PHY2_GATE		106
+#define CLK_TREE_USB3C_DRD_PHY3_GATE		107
+#define CLK_TREE_USB3C_0_AXI_GATE		108
+#define CLK_TREE_USB3C_0_APB_GATE		109
+#define CLK_TREE_USB3C_0_PHY2_GATE		110
+#define CLK_TREE_USB3C_0_PHY3_GATE		111
+#define CLK_TREE_USB3C_1_AXI_GATE		112
+#define CLK_TREE_USB3C_1_APB_GATE		113
+#define CLK_TREE_USB3C_1_PHY2_GATE		114
+#define CLK_TREE_USB3C_1_PHY3_GATE		115
+#define CLK_TREE_USB3C_2_AXI_GATE		116
+#define CLK_TREE_USB3C_2_APB_GATE		117
+#define CLK_TREE_USB3C_2_PHY2_GATE		118
+#define CLK_TREE_USB3C_2_PHY3_GATE		119
+#define CLK_TREE_USB3A_0_AXI_GATE		120
+#define CLK_TREE_USB3A_0_APB_GATE		121
+#define CLK_TREE_USB3A_0_PHY2_GATE		122
+#define CLK_TREE_USB3A_1_AXI_GATE		123
+#define CLK_TREE_USB3A_1_APB_GATE		124
+#define CLK_TREE_USB3A_1_PHY2_GATE		125
+#define CLK_TREE_USB3A_PHY3_GATE		126
+#define CLK_TREE_USB2_0_CLK_SOF			127
+#define CLK_TREE_USB2_1_CLK_SOF			128
+#define CLK_TREE_USB2_2_CLK_SOF			129
+#define CLK_TREE_USB2_3_CLK_SOF			130
+#define CLK_TREE_USB3C_DRD_CLK_SOF		131
+#define CLK_TREE_USB3C_H0_CLK_SOF		132
+#define CLK_TREE_USB3C_H1_CLK_SOF		133
+#define CLK_TREE_USB3C_H2_CLK_SOF		134
+#define CLK_TREE_USB3A_H0_CLK_SOF		135
+#define CLK_TREE_USB3A_H1_CLK_SOF		136
+#define CLK_TREE_USB2_0_CLK_LPM			137
+#define CLK_TREE_USB2_1_CLK_LPM			138
+#define CLK_TREE_USB2_2_CLK_LPM			139
+#define CLK_TREE_USB2_3_CLK_LPM			140
+#define CLK_TREE_USB3C_DRD_CLK_LPM		141
+#define CLK_TREE_USB3C_H0_CLK_LPM		142
+#define CLK_TREE_USB3C_H1_CLK_LPM		143
+#define CLK_TREE_USB3C_H2_CLK_LPM		144
+#define CLK_TREE_USB3A_H0_CLK_LPM		145
+#define CLK_TREE_USB3A_H1_CLK_LPM		146
+#define CLK_TREE_USB2_0_PHY_REF			147
+#define CLK_TREE_USB2_1_PHY_REF			148
+#define CLK_TREE_USB2_2_PHY_REF			149
+#define CLK_TREE_USB2_3_PHY_REF			150
+#define CLK_TREE_USB3C_DRD_PHY_REF		151
+#define CLK_TREE_USB3C_H0_PHY_REF		152
+#define CLK_TREE_USB3C_H1_PHY_REF		153
+#define CLK_TREE_USB3C_H2_PHY_REF		154
+#define CLK_TREE_USB3A_H0_PHY_REF		155
+#define CLK_TREE_USB3A_H1_PHY_REF		156
+#define CLK_TREE_USB3C_DRD_PHY_x4_REF		157
+#define CLK_TREE_USB3C_H0_PHY_x4_REF		158
+#define CLK_TREE_USB3C_H1_PHY_x4_REF		159
+#define CLK_TREE_USB3C_H2_PHY_x4_REF		160
+#define CLK_TREE_USB3A_PHY_x2_REF		161
+#define CLK_TREE_PCIE_X8CTRL_APB		162
+#define CLK_TREE_PCIE_X4CTRL_APB		163
+#define CLK_TREE_PCIE_X2CTRL_APB		164
+#define CLK_TREE_PCIE_X1_0CTRL_APB		165
+#define CLK_TREE_PCIE_X1_1CTRL_APB		166
+#define CLK_TREE_PCIE_X8_PHY_APB		167
+#define CLK_TREE_PCIE_X4_PHY_APB		168
+#define CLK_TREE_PCIE_X211_PHY_APB		169
+#define CLK_TREE_PCIE_NI700_CLK			170
+#define CLK_TREE_PCIE_CTRL0_CLK			171
+#define CLK_TREE_PCIE_CTRL1_CLK			172
+#define CLK_TREE_PCIE_CTRL2_CLK			173
+#define CLK_TREE_PCIE_CTRL3_CLK			174
+#define CLK_TREE_PCIE_CTRL4_CLK			175
+#define CLK_TREE_CSI_CTRL0_SYSCLK		176
+#define CLK_TREE_CSI_CTRL1_SYSCLK		177
+#define CLK_TREE_CSI_CTRL2_SYSCLK		178
+#define CLK_TREE_CSI_CTRL3_SYSCLK		179
+#define CLK_TREE_CSI_CTRL0_PIXEL0_CLK		180
+#define CLK_TREE_CSI_CTRL0_PIXEL1_CLK		181
+#define CLK_TREE_CSI_CTRL0_PIXEL2_CLK		182
+#define CLK_TREE_CSI_CTRL0_PIXEL3_CLK		183
+#define CLK_TREE_CSI_CTRL1_PIXEL0_CLK		184
+#define CLK_TREE_CSI_CTRL2_PIXEL0_CLK		185
+#define CLK_TREE_CSI_CTRL2_PIXEL1_CLK		186
+#define CLK_TREE_CSI_CTRL2_PIXEL2_CLK		187
+#define CLK_TREE_CSI_CTRL2_PIXEL3_CLK		188
+#define CLK_TREE_CSI_CTRL3_PIXEL0_CLK		189
+#define CLK_TREE_CI700_GCLK0			190
+#define CLK_TREE_DDRC0_ACLK_CLK			191
+#define CLK_TREE_DDRC1_ACLK_CLK			192
+#define CLK_TREE_DDRC2_ACLK_CLK			193
+#define CLK_TREE_DDRC3_ACLK_CLK			194
+#define CLK_TREE_DDRC0_DFICLK_CLK		195
+#define CLK_TREE_DDRC1_DFICLK_CLK		196
+#define CLK_TREE_DDRC2_DFICLK_CLK		197
+#define CLK_TREE_DDRC3_DFICLK_CLK		198
+#define CLK_TREE_PHY0_SYNC_CLK			199
+#define CLK_TREE_PHY1_SYNC_CLK			200
+#define CLK_TREE_PHY2_SYNC_CLK			201
+#define CLK_TREE_PHY3_SYNC_CLK			202
+#define CLK_TREE_PHY0_BYPASS_CLK		203
+#define CLK_TREE_PHY1_BYPASS_CLK		204
+#define CLK_TREE_PHY2_BYPASS_CLK		205
+#define CLK_TREE_PHY3_BYPASS_CLK		206
+#define CLK_TREE_DDRC_0_APB			207
+#define CLK_TREE_DDRC_1_APB			208
+#define CLK_TREE_DDRC_2_APB			209
+#define CLK_TREE_DDRC_3_APB			210
+#define CLK_TREE_TZC400_0_APB			211
+#define CLK_TREE_TZC400_1_APB			212
+#define CLK_TREE_TZC400_2_APB			213
+#define CLK_TREE_TZC400_3_APB			214
+#define CLK_TREE_S5_SENSOR_HUB_25M		215
+#define CLK_TREE_S5_SENSOR_HUB_400M		216
+#define CLK_TREE_S5_CSS600_100M			217
+#define CLK_TREE_S5_DFD_800M			218
+#define CLK_TREE_S5_CSU_SE_800M			219
+#define CLK_TREE_S5_CSU_PM_800M			220
+#define CLK_TREE_PCIE_REF_B0			221
+#define CLK_TREE_PCIE_REF_B1			222
+#define CLK_TREE_PCIE_REF_B2			223
+#define CLK_TREE_PCIE_REF_B3			224
+#define CLK_TREE_PCIE_REF_B4			225
+#define CLK_TREE_PCIE_REF_PHY_X8		226
+#define CLK_TREE_PCIE_REF_PHY_X4		227
+#define CLK_TREE_PCIE_REF_PHY_X211		228
+#define CLK_TREE_GMAC_REC_CLK			229
+#define CLK_TREE_GPUTOP_PLL			230
+#define CLK_TREE_GPUCORE_PLL			231
+#define CLK_TREE_CPU_PLL_LIT			232
+#define CLK_TREE_CPU_PLL0			233
+#define CLK_TREE_CPU_PLL1			234
+#define CLK_TREE_CPU_PLL2			235
+#define CLK_TREE_CPU_PLL3			236
+#define CLK_TREE_FCH_I3C0_FUNC			237
+#define CLK_TREE_FCH_I3C1_FUNC			238
+#define CLK_TREE_FCH_DMA_ACLK			239
+#define CLK_TREE_FCH_XSPI_FUNC			240
+#define CLK_TREE_FCH_XSPI_MACLK			241
+#define CLK_TREE_FCH_TIMER_FUN			242
+#define CLK_TREE_FCH_APB_IO_S0			243
+#define CLK_TREE_FCH_I3C0_APB			244
+#define CLK_TREE_FCH_I3C1_APB			245
+#define CLK_TREE_FCH_UART0_APB			246
+#define CLK_TREE_FCH_UART1_APB			247
+#define CLK_TREE_FCH_UART2_APB			248
+#define CLK_TREE_FCH_UART3_APB			249
+#define CLK_TREE_FCH_SPI0_APB			250
+#define CLK_TREE_FCH_SPI1_APB			251
+#define CLK_TREE_FCH_XSPI_APB			252
+#define CLK_TREE_FCH_I2C0_APB			253
+#define CLK_TREE_FCH_I2C1_APB			254
+#define CLK_TREE_FCH_I2C2_APB			255
+#define CLK_TREE_FCH_I2C3_APB			256
+#define CLK_TREE_FCH_I2C4_APB			257
+#define CLK_TREE_FCH_I2C5_APB			258
+#define CLK_TREE_FCH_I2C6_APB			259
+#define CLK_TREE_FCH_I2C7_APB			260
+#define CLK_TREE_FCH_TIMER_APB			261
+#define CLK_TREE_FCH_GPIO_APB			262
+#define CLK_TREE_FCH_UART0_FUNC			263
+#define CLK_TREE_FCH_UART1_FUNC			264
+#define CLK_TREE_FCH_UART2_FUNC			265
+#define CLK_TREE_FCH_UART3_FUNC			266
+/* 267~271 not used by AP, skip */
+#define CLK_TREE_GPU_CLK_200M			272
+
+#endif