usb: dwc3: Add workaround for isoc start transfer failure

In DWC_usb31 version 1.70a-ea06 and prior, for highspeed and fullspeed
isochronous IN, BIT[15:14] of the 16-bit microframe number reported by
the XferNotReady event are invalid. The driver uses this number to
schedule the isochronous transfer and passes it to the START TRANSFER
command. Because this number is invalid, the command may fail. If
BIT[15:14] matches the internal 16-bit microframe, the START TRANSFER
command will pass and the transfer will start at the scheduled time, if
it is off by 1, the command will still pass, but the transfer will start
2 seconds in the future. For all other conditions, the START TRANSFER
command will fail with bus-expiry.

In order to workaround this issue, we can test for the correct
combination of BIT[15:14] by sending START TRANSFER commands with
different values of BIT[15:14]: 'b00, 'b01, 'b10, and 'b11. Each
combination is 2^14 uframe apart (or 2 seconds). 4 seconds into the
future will result in a bus-expiry status. As the result, within the 4
possible combinations for BIT[15:14], there will be 2 successful and 2
failure START COMMAND status. One of the 2 successful command status
will result in a 2-second delay start. The smaller BIT[15:14] value is
the correct combination.

Since there are only 4 outcomes and the results are ordered, we can
simply test 2 START TRANSFER commands with BIT[15:14] combinations 'b00
and 'b01 to deduce the smaller successful combination.

Let test0 = test status for combination 'b00 and test1 = test status for
'b01 of BIT[15:14]. The correct combination is as follow:

if test0 fails and test1 passes, BIT[15:14] is 'b01
if test0 fails and test1 fails, BIT[15:14] is 'b10
if test0 passes and test1 fails, BIT[15:14] is 'b11
if test0 passes and test1 passes, BIT[15:14] is 'b00

Synopsys STAR 9001202023: Wrong microframe number for isochronous IN
endpoints.

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

1 files changed, 13 insertions, 0 deletions

diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index 709e8dd356ee..0136aa7766e1 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -666,6 +666,10 @@ struct dwc3_event_buffer {
  * @name: a human readable name e.g. ep1out-bulk
  * @direction: true for TX, false for RX
  * @stream_capable: true when streams are enabled
+ * @combo_num: the test combination BIT[15:14] of the frame number to test
+ *		isochronous START TRANSFER command failure workaround
+ * @start_cmd_status: the status of testing START TRANSFER command with
+ *		combo_num = 'b00
  */
 struct dwc3_ep {
 	struct usb_ep		endpoint;
@@ -715,6 +719,10 @@ struct dwc3_ep {
 
 	unsigned		direction:1;
 	unsigned		stream_capable:1;
+
+	/* For isochronous START TRANSFER workaround only */
+	u8			combo_num;
+	int			start_cmd_status;
 };
 
 enum dwc3_phy {
@@ -982,6 +990,8 @@ struct dwc3_scratchpad_array {
  * @pullups_connected: true when Run/Stop bit is set
  * @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround
  * @three_stage_setup: set if we perform a three phase setup
+ * @dis_start_transfer_quirk: set if start_transfer failure SW workaround is
+ *			not needed for DWC_usb31 version 1.70a-ea06 and below
  * @usb3_lpm_capable: set if hadrware supports Link Power Management
  * @usb2_lpm_disable: set to disable usb2 lpm
  * @disable_scramble_quirk: set if we enable the disable scramble quirk
@@ -1117,6 +1127,8 @@ struct dwc3 {
 #define DWC3_REVISION_IS_DWC31		0x80000000
 #define DWC3_USB31_REVISION_110A	(0x3131302a | DWC3_REVISION_IS_DWC31)
 #define DWC3_USB31_REVISION_120A	(0x3132302a | DWC3_REVISION_IS_DWC31)
+#define DWC3_USB31_REVISION_160A	(0x3136302a | DWC3_REVISION_IS_DWC31)
+#define DWC3_USB31_REVISION_170A	(0x3137302a | DWC3_REVISION_IS_DWC31)
 
 	u32			version_type;
 
@@ -1170,6 +1182,7 @@ struct dwc3 {
 	unsigned		pullups_connected:1;
 	unsigned		setup_packet_pending:1;
 	unsigned		three_stage_setup:1;
+	unsigned		dis_start_transfer_quirk:1;
 	unsigned		usb3_lpm_capable:1;
 	unsigned		usb2_lpm_disable:1;