Merge tag 'wireless-drivers-next-2020-05-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.8

First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.

In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.

Major changes:

ath11k

* add debugfs file for testing ADDBA and DELBA

* add 802.11 encapsulation offload on hardware support

* add htt_peer_stats_reset debugfs file

ath10k

* enable VHT160 and VHT80+80 modes

* enable radar detection in secondary segment

* sdio: disable TX complete indication to improve throughput

* sdio: decrease power consumption

* sdio: add HTT TX bundle support to increase throughput

* sdio: add rx bitrate reporting

ath9k

* improvements to AR9002 calibration logic

carl9170

* remove buggy P2P_GO support

p54usb

* add support for AirVasT USB stick

rtw88

* add support for antenna configuration

ti wlcore

* add support for AES_CMAC cipher

iwlwifi

* support for a few new FW API versions

* new hw configs
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 43 insertions, 19 deletions

diff --git a/include/linux/iopoll.h b/include/linux/iopoll.h
index cb20c733b15a..bc89ac625f26 100644
--- a/include/linux/iopoll.h
+++ b/include/linux/iopoll.h
@@ -58,6 +58,48 @@
 })
 
 /**
+ * read_poll_timeout_atomic - Periodically poll an address until a condition is
+ * 				met or a timeout occurs
+ * @op: accessor function (takes @addr as its only argument)
+ * @addr: Address to poll
+ * @val: Variable to read the value into
+ * @cond: Break condition (usually involving @val)
+ * @delay_us: Time to udelay between reads in us (0 tight-loops).  Should
+ *            be less than ~10us since udelay is used (see
+ *            Documentation/timers/timers-howto.rst).
+ * @timeout_us: Timeout in us, 0 means never timeout
+ * @delay_before_read: if it is true, delay @delay_us before read.
+ *
+ * Returns 0 on success and -ETIMEDOUT upon a timeout. In either
+ * case, the last read value at @args is stored in @val.
+ *
+ * When available, you'll probably want to use one of the specialized
+ * macros defined below rather than this macro directly.
+ */
+#define read_poll_timeout_atomic(op, val, cond, delay_us, timeout_us, \
+					delay_before_read, args...) \
+({ \
+	u64 __timeout_us = (timeout_us); \
+	unsigned long __delay_us = (delay_us); \
+	ktime_t __timeout = ktime_add_us(ktime_get(), __timeout_us); \
+	if (delay_before_read && __delay_us) \
+		udelay(__delay_us); \
+	for (;;) { \
+		(val) = op(args); \
+		if (cond) \
+			break; \
+		if (__timeout_us && \
+		    ktime_compare(ktime_get(), __timeout) > 0) { \
+			(val) = op(args); \
+			break; \
+		} \
+		if (__delay_us) \
+			udelay(__delay_us); \
+	} \
+	(cond) ? 0 : -ETIMEDOUT; \
+})
+
+/**
  * readx_poll_timeout - Periodically poll an address until a condition is met or a timeout occurs
  * @op: accessor function (takes @addr as its only argument)
  * @addr: Address to poll
@@ -96,25 +138,7 @@
  * macros defined below rather than this macro directly.
  */
 #define readx_poll_timeout_atomic(op, addr, val, cond, delay_us, timeout_us) \
-({ \
-	u64 __timeout_us = (timeout_us); \
-	unsigned long __delay_us = (delay_us); \
-	ktime_t __timeout = ktime_add_us(ktime_get(), __timeout_us); \
-	for (;;) { \
-		(val) = op(addr); \
-		if (cond) \
-			break; \
-		if (__timeout_us && \
-		    ktime_compare(ktime_get(), __timeout) > 0) { \
-			(val) = op(addr); \
-			break; \
-		} \
-		if (__delay_us) \
-			udelay(__delay_us);	\
-	} \
-	(cond) ? 0 : -ETIMEDOUT; \
-})
-
+	read_poll_timeout_atomic(op, val, cond, delay_us, timeout_us, false, addr)
 
 #define readb_poll_timeout(addr, val, cond, delay_us, timeout_us) \
 	readx_poll_timeout(readb, addr, val, cond, delay_us, timeout_us)