diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt')
-rw-r--r-- | Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt | 72 |
1 files changed, 0 insertions, 72 deletions
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt deleted file mode 100644 index 8e4729de8c85..000000000000 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt +++ /dev/null @@ -1,72 +0,0 @@ -Mediatek DSI Device -=================== - -The Mediatek DSI function block is a sink of the display subsystem and can -drive up to 4-lane MIPI DSI output. Two DSIs can be synchronized for dual- -channel output. - -Required properties: -- compatible: "mediatek,<chip>-dsi" - the supported chips are mt2701, mt8173 and mt8183. -- reg: Physical base address and length of the controller's registers -- interrupts: The interrupt signal from the function block. -- clocks: device clocks - See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. -- clock-names: must contain "engine", "digital", and "hs" -- phys: phandle link to the MIPI D-PHY controller. -- phy-names: must contain "dphy" -- port: Output port node with endpoint definitions as described in - Documentation/devicetree/bindings/graph.txt. This port should be connected - to the input port of an attached DSI panel or DSI-to-eDP encoder chip. - -MIPI TX Configuration Module -============================ - -The MIPI TX configuration module controls the MIPI D-PHY. - -Required properties: -- compatible: "mediatek,<chip>-mipi-tx" - the supported chips are mt2701, mt8173 and mt8183. -- reg: Physical base address and length of the controller's registers -- clocks: PLL reference clock -- clock-output-names: name of the output clock line to the DSI encoder -- #clock-cells: must be <0>; -- #phy-cells: must be <0>. - -Optional properties: -- drive-strength-microamp: adjust driving current, should be 3000 ~ 6000. And - the step is 200. -- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If - unspecified default values shall be used. -- nvmem-cell-names: Should be "calibration-data" - -Example: - -mipi_tx0: mipi-dphy@10215000 { - compatible = "mediatek,mt8173-mipi-tx"; - reg = <0 0x10215000 0 0x1000>; - clocks = <&clk26m>; - clock-output-names = "mipi_tx0_pll"; - #clock-cells = <0>; - #phy-cells = <0>; - drive-strength-microamp = <4600>; - nvmem-cells= <&mipi_tx_calibration>; - nvmem-cell-names = "calibration-data"; -}; - -dsi0: dsi@1401b000 { - compatible = "mediatek,mt8173-dsi"; - reg = <0 0x1401b000 0 0x1000>; - interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_LOW>; - clocks = <&mmsys MM_DSI0_ENGINE>, <&mmsys MM_DSI0_DIGITAL>, - <&mipi_tx0>; - clock-names = "engine", "digital", "hs"; - phys = <&mipi_tx0>; - phy-names = "dphy"; - - port { - dsi0_out: endpoint { - remote-endpoint = <&panel_in>; - }; - }; -}; |