diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa/ocelot.txt')
-rw-r--r-- | Documentation/devicetree/bindings/net/dsa/ocelot.txt | 116 |
1 files changed, 0 insertions, 116 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/ocelot.txt b/Documentation/devicetree/bindings/net/dsa/ocelot.txt deleted file mode 100644 index 66a129fea705..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/ocelot.txt +++ /dev/null @@ -1,116 +0,0 @@ -Microchip Ocelot switch driver family -===================================== - -Felix ------ - -The VSC9959 core is currently the only switch supported by the driver, and is -found in the NXP LS1028A. It is a PCI device, part of the larger ENETC root -complex. As a result, the ethernet-switch node is a sub-node of the PCIe root -complex node and its "reg" property conforms to the parent node bindings: - -* reg: Specifies PCIe Device Number and Function Number of the endpoint device, - in this case for the Ethernet L2Switch it is PF5 (of device 0, bus 0). - -It does not require a "compatible" string. - -The interrupt line is used to signal availability of PTP TX timestamps and for -TSN frame preemption. - -For the external switch ports, depending on board configuration, "phy-mode" and -"phy-handle" are populated by board specific device tree instances. Ports 4 and -5 are fixed as internal ports in the NXP LS1028A instantiation. - -The CPU port property ("ethernet") configures the feature called "NPI port" in -the Ocelot hardware core. The CPU port in Ocelot is a set of queues, which are -connected, in the Node Processor Interface (NPI) mode, to an Ethernet port. -By default, in fsl-ls1028a.dtsi, the NPI port is assigned to the internal -2.5Gbps port@4, but can be moved to the 1Gbps port@5, depending on the specific -use case. Moving the NPI port to an external switch port is hardware possible, -but there is no platform support for the Linux system on the LS1028A chip to -operate as an entire slave DSA chip. NPI functionality (and therefore DSA -tagging) is supported on a single port at a time. - -Any port can be disabled (and in fsl-ls1028a.dtsi, they are indeed all disabled -by default, and should be enabled on a per-board basis). But if any external -switch port is enabled at all, the ENETC PF2 (enetc_port2) should be enabled as -well, regardless of whether it is configured as the DSA master or not. This is -because the Felix PHYLINK implementation accesses the MAC PCS registers, which -in hardware truly belong to the ENETC port #2 and not to Felix. - -Supported PHY interface types (appropriate SerDes protocol setting changes are -needed in the RCW binary): - -* phy_mode = "internal": on ports 4 and 5 -* phy_mode = "sgmii": on ports 0, 1, 2, 3 -* phy_mode = "qsgmii": on ports 0, 1, 2, 3 -* phy_mode = "usxgmii": on ports 0, 1, 2, 3 -* phy_mode = "2500base-x": on ports 0, 1, 2, 3 - -For the rest of the device tree binding definitions, which are standard DSA and -PCI, refer to the following documents: - -Documentation/devicetree/bindings/net/dsa/dsa.txt -Documentation/devicetree/bindings/pci/pci.txt - -Example: - -&soc { - pcie@1f0000000 { /* Integrated Endpoint Root Complex */ - ethernet-switch@0,5 { - reg = <0x000500 0 0 0 0>; - /* IEP INT_B */ - interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - /* External ports */ - port@0 { - reg = <0>; - label = "swp0"; - }; - - port@1 { - reg = <1>; - label = "swp1"; - }; - - port@2 { - reg = <2>; - label = "swp2"; - }; - - port@3 { - reg = <3>; - label = "swp3"; - }; - - /* Tagging CPU port */ - port@4 { - reg = <4>; - ethernet = <&enetc_port2>; - phy-mode = "internal"; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - - /* Non-tagging CPU port */ - port@5 { - reg = <5>; - phy-mode = "internal"; - status = "disabled"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; - }; -}; |