diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi')
| -rw-r--r-- | arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi | 270 |
1 files changed, 270 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi new file mode 100644 index 000000000000..fbd2caf405d5 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi @@ -0,0 +1,270 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include "msm8916-modem-qdsp6.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/sound/apq8016-lpass.h> + +/ { + aliases { + mmc0 = &sdhc_1; /* eMMC */ + mmc1 = &sdhc_2; /* SD card */ + serial0 = &blsp_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + reserved-memory { + /* Additional memory used by Samsung firmware modifications */ + tz-apps@85500000 { + reg = <0x0 0x85500000 0x0 0xb00000>; + no-map; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&gpio_keys_default>; + pinctrl-names = "default"; + + label = "GPIO Buttons"; + + volume-up-button { + label = "Volume Up"; + gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + + home-button { + label = "Home"; + gpios = <&tlmm 109 GPIO_ACTIVE_LOW>; + linux,code = <KEY_HOMEPAGE>; + }; + }; + + gpio-hall-sensor { + compatible = "gpio-keys"; + + pinctrl-0 = <&gpio_hall_sensor_default>; + pinctrl-names = "default"; + + label = "GPIO Hall Effect Sensor"; + + hall-sensor-switch { + label = "Hall Effect Sensor"; + gpios = <&tlmm 52 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + linux,can-disable; + }; + }; +}; + +&blsp_i2c2 { + status = "okay"; + + light-sensor@10 { + compatible = "capella,cm3323"; + reg = <0x10>; + }; + + accelerometer@1d { + compatible = "st,lis2hh12"; + reg = <0x1d>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; + + interrupt-parent = <&tlmm>; + interrupts = <115 IRQ_TYPE_LEVEL_HIGH>; + + st,drdy-int-pin = <1>; + mount-matrix = "0", "1", "0", + "-1", "0", "0", + "0", "0", "1"; + + pinctrl-0 = <&accel_int_default>; + pinctrl-names = "default"; + }; +}; + +&blsp_i2c4 { + status = "okay"; + + fuelgauge@36 { + compatible = "maxim,max77849-battery"; + reg = <0x36>; + + maxim,rsns-microohm = <10000>; + maxim,over-heat-temp = <600>; + maxim,over-volt = <4400>; + + interrupt-parent = <&tlmm>; + interrupts = <121 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-0 = <&fuelgauge_int_default>; + pinctrl-names = "default"; + }; +}; + +&blsp_uart2 { + status = "okay"; +}; + +/* + * For some reason the speaker amplifier is connected to the second SD line + * (MI2S_2_D1) instead of the first (MI2S_2_D0). This must be configured in the + * device tree, otherwise audio will seemingly play fine on the wrong SD line + * but the speaker stays silent. + * + * When routing audio via QDSP6 (the default) the &lpass node is reserved and + * the definitions from &q6afedai are used. When the modem is disabled audio can + * be alternatively routed directly to the LPASS hardware with reduced latency. + * The definitions for &lpass are here for completeness to simplify changing the + * setup with minor changes to the DT (either manually or with DT overlays). + */ +&lpass { + dai-link@3 { + reg = <MI2S_QUATERNARY>; + qcom,playback-sd-lines = <1>; + }; +}; + +&mpss_mem { + reg = <0x0 0x86800000 0x0 0x5400000>; +}; + +&pm8916_resin { + linux,code = <KEY_VOLUMEDOWN>; + status = "okay"; +}; + +&pm8916_rpm_regulators { + pm8916_l17: l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; +}; + +/* FIXME: Replace with MAX77849 MUIC when driver is available */ +&pm8916_usbin { + status = "okay"; +}; + +&q6afedai { + dai@22 { + reg = <QUATERNARY_MI2S_RX>; + qcom,sd-lines = <1>; + }; +}; + +&sdhc_1 { + status = "okay"; +}; + +&sdhc_2 { + pinctrl-0 = <&sdc2_default &sdc2_cd_default>; + pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>; + pinctrl-names = "default", "sleep"; + + cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; + + status = "okay"; +}; + +&sound { + audio-routing = + "AMIC1", "MIC BIAS External1", + "AMIC2", "MIC BIAS Internal2", + "AMIC3", "MIC BIAS External1"; + + sound_link_backend2: backend2-dai-link { + link-name = "Quaternary MI2S"; + + cpu { + sound-dai = <&q6afedai QUATERNARY_MI2S_RX>; + }; + platform { + sound-dai = <&q6routing>; + }; + codec { + sound-dai = <&speaker_codec>; + }; + }; +}; + +&usb { + dr_mode = "peripheral"; + extcon = <&pm8916_usbin>; + + status = "okay"; +}; + +&usb_hs_phy { + extcon = <&pm8916_usbin>; +}; + +&venus { + status = "okay"; +}; + +&venus_mem { + status = "okay"; +}; + +&wcnss { + status = "okay"; +}; + +&wcnss_iris { + compatible = "qcom,wcn3660b"; +}; + +&wcnss_mem { + status = "okay"; +}; + +&tlmm { + accel_int_default: accel-int-default-state { + pins = "gpio115"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + fuelgauge_int_default: fuelgauge-int-default-state { + pins = "gpio121"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + gpio_keys_default: gpio-keys-default-state { + pins = "gpio107", "gpio109"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + + gpio_hall_sensor_default: gpio-hall-sensor-default-state { + pins = "gpio52"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + sdc2_cd_default: sdc2-cd-default-state { + pins = "gpio38"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; +}; |