diff options
Diffstat (limited to 'include/linux/phylink.h')
| -rw-r--r-- | include/linux/phylink.h | 498 |
1 files changed, 407 insertions, 91 deletions
diff --git a/include/linux/phylink.h b/include/linux/phylink.h index d81a714cfbbd..30659b615fca 100644 --- a/include/linux/phylink.h +++ b/include/linux/phylink.h @@ -5,10 +5,13 @@ #include <linux/spinlock.h> #include <linux/workqueue.h> +#include <net/eee.h> + struct device_node; struct ethtool_cmd; struct fwnode_handle; struct net_device; +struct phylink; enum { MLO_PAUSE_NONE, @@ -20,6 +23,76 @@ enum { MLO_AN_PHY = 0, /* Conventional PHY */ MLO_AN_FIXED, /* Fixed-link mode */ MLO_AN_INBAND, /* In-band protocol */ + + /* PCS "negotiation" mode. + * PHYLINK_PCS_NEG_NONE - protocol has no inband capability + * PHYLINK_PCS_NEG_OUTBAND - some out of band or fixed link setting + * PHYLINK_PCS_NEG_INBAND_DISABLED - inband mode disabled, e.g. + * 1000base-X with autoneg off + * PHYLINK_PCS_NEG_INBAND_ENABLED - inband mode enabled + * Additionally, this can be tested using bitmasks: + * PHYLINK_PCS_NEG_INBAND - inband mode selected + * PHYLINK_PCS_NEG_ENABLED - negotiation mode enabled + */ + PHYLINK_PCS_NEG_NONE = 0, + PHYLINK_PCS_NEG_ENABLED = BIT(4), + PHYLINK_PCS_NEG_OUTBAND = BIT(5), + PHYLINK_PCS_NEG_INBAND = BIT(6), + PHYLINK_PCS_NEG_INBAND_DISABLED = PHYLINK_PCS_NEG_INBAND, + PHYLINK_PCS_NEG_INBAND_ENABLED = PHYLINK_PCS_NEG_INBAND | + PHYLINK_PCS_NEG_ENABLED, + + /* MAC_SYM_PAUSE and MAC_ASYM_PAUSE are used when configuring our + * autonegotiation advertisement. They correspond to the PAUSE and + * ASM_DIR bits defined by 802.3, respectively. + * + * The following table lists the values of tx_pause and rx_pause which + * might be requested in mac_link_up. The exact values depend on either + * the results of autonegotation (if MLO_PAUSE_AN is set) or user + * configuration (if MLO_PAUSE_AN is not set). + * + * MAC_SYM_PAUSE MAC_ASYM_PAUSE MLO_PAUSE_AN tx_pause/rx_pause + * ============= ============== ============ ================== + * 0 0 0 0/0 + * 0 0 1 0/0 + * 0 1 0 0/0, 0/1, 1/0, 1/1 + * 0 1 1 0/0, 1/0 + * 1 0 0 0/0, 1/1 + * 1 0 1 0/0, 1/1 + * 1 1 0 0/0, 0/1, 1/0, 1/1 + * 1 1 1 0/0, 0/1, 1/1 + * + * If you set MAC_ASYM_PAUSE, the user may request any combination of + * tx_pause and rx_pause. You do not have to support these + * combinations. + * + * However, you should support combinations of tx_pause and rx_pause + * which might be the result of autonegotation. For example, don't set + * MAC_SYM_PAUSE unless your device can support tx_pause and rx_pause + * at the same time. + */ + MAC_SYM_PAUSE = BIT(0), + MAC_ASYM_PAUSE = BIT(1), + MAC_10HD = BIT(2), + MAC_10FD = BIT(3), + MAC_10 = MAC_10HD | MAC_10FD, + MAC_100HD = BIT(4), + MAC_100FD = BIT(5), + MAC_100 = MAC_100HD | MAC_100FD, + MAC_1000HD = BIT(6), + MAC_1000FD = BIT(7), + MAC_1000 = MAC_1000HD | MAC_1000FD, + MAC_2500FD = BIT(8), + MAC_5000FD = BIT(9), + MAC_10000FD = BIT(10), + MAC_20000FD = BIT(11), + MAC_25000FD = BIT(12), + MAC_40000FD = BIT(13), + MAC_50000FD = BIT(14), + MAC_56000FD = BIT(15), + MAC_100000FD = BIT(16), + MAC_200000FD = BIT(17), + MAC_400000FD = BIT(18), }; static inline bool phylink_autoneg_inband(unsigned int mode) @@ -36,8 +109,11 @@ static inline bool phylink_autoneg_inband(unsigned int mode) * @speed: link speed, one of the SPEED_* constants. * @duplex: link duplex mode, one of DUPLEX_* constants. * @pause: link pause state, described by MLO_PAUSE_* constants. + * @rate_matching: rate matching being performed, one of the RATE_MATCH_* + * constants. If rate matching is taking place, then the speed/duplex of + * the medium link mode (@speed and @duplex) and the speed/duplex of the phy + * interface mode (@interface) are different. * @link: true if the link is up. - * @an_enabled: true if autonegotiation is enabled/desired. * @an_complete: true if autonegotiation has completed. */ struct phylink_link_state { @@ -47,8 +123,8 @@ struct phylink_link_state { int speed; int duplex; int pause; + int rate_matching; unsigned int link:1; - unsigned int an_enabled:1; unsigned int an_complete:1; }; @@ -61,99 +137,110 @@ enum phylink_op_type { * struct phylink_config - PHYLINK configuration structure * @dev: a pointer to a struct device associated with the MAC * @type: operation type of PHYLINK instance - * @pcs_poll: MAC PCS cannot provide link change interrupt * @poll_fixed_state: if true, starts link_poll, * if MAC link is at %MLO_AN_FIXED mode. + * @mac_managed_pm: if true, indicate the MAC driver is responsible for PHY PM. + * @mac_requires_rxc: if true, the MAC always requires a receive clock from PHY. + * The PHY driver should start the clock signal as soon as + * possible and avoid stopping it during suspend events. + * @default_an_inband: if true, defaults to MLO_AN_INBAND rather than + * MLO_AN_PHY. A fixed-link specification will override. + * @eee_rx_clk_stop_enable: if true, PHY can stop the receive clock during LPI * @get_fixed_state: callback to execute to determine the fixed link state, * if MAC link is at %MLO_AN_FIXED mode. + * @supported_interfaces: bitmap describing which PHY_INTERFACE_MODE_xxx + * are supported by the MAC/PCS. + * @lpi_interfaces: bitmap describing which PHY interface modes can support + * LPI signalling. + * @mac_capabilities: MAC pause/speed/duplex capabilities. + * @lpi_capabilities: MAC speeds which can support LPI signalling + * @lpi_timer_default: Default EEE LPI timer setting. + * @eee_enabled_default: If set, EEE will be enabled by phylink at creation time */ struct phylink_config { struct device *dev; enum phylink_op_type type; - bool pcs_poll; bool poll_fixed_state; + bool mac_managed_pm; + bool mac_requires_rxc; + bool default_an_inband; + bool eee_rx_clk_stop_enable; void (*get_fixed_state)(struct phylink_config *config, struct phylink_link_state *state); + DECLARE_PHY_INTERFACE_MASK(supported_interfaces); + DECLARE_PHY_INTERFACE_MASK(lpi_interfaces); + unsigned long mac_capabilities; + unsigned long lpi_capabilities; + u32 lpi_timer_default; + bool eee_enabled_default; }; +void phylink_limit_mac_speed(struct phylink_config *config, u32 max_speed); + /** * struct phylink_mac_ops - MAC operations structure. - * @validate: Validate and update the link configuration. - * @mac_pcs_get_state: Read the current link state from the hardware. + * @mac_get_caps: Get MAC capabilities for interface mode. + * @mac_select_pcs: Select a PCS for the interface mode. * @mac_prepare: prepare for a major reconfiguration of the interface. * @mac_config: configure the MAC for the selected mode and state. * @mac_finish: finish a major reconfiguration of the interface. - * @mac_an_restart: restart 802.3z BaseX autonegotiation. * @mac_link_down: take the link down. * @mac_link_up: allow the link to come up. + * @mac_disable_tx_lpi: disable LPI. + * @mac_enable_tx_lpi: enable and configure LPI. * * The individual methods are described more fully below. */ struct phylink_mac_ops { - void (*validate)(struct phylink_config *config, - unsigned long *supported, - struct phylink_link_state *state); - void (*mac_pcs_get_state)(struct phylink_config *config, - struct phylink_link_state *state); + unsigned long (*mac_get_caps)(struct phylink_config *config, + phy_interface_t interface); + struct phylink_pcs *(*mac_select_pcs)(struct phylink_config *config, + phy_interface_t interface); int (*mac_prepare)(struct phylink_config *config, unsigned int mode, phy_interface_t iface); void (*mac_config)(struct phylink_config *config, unsigned int mode, const struct phylink_link_state *state); int (*mac_finish)(struct phylink_config *config, unsigned int mode, phy_interface_t iface); - void (*mac_an_restart)(struct phylink_config *config); void (*mac_link_down)(struct phylink_config *config, unsigned int mode, phy_interface_t interface); void (*mac_link_up)(struct phylink_config *config, struct phy_device *phy, unsigned int mode, phy_interface_t interface, int speed, int duplex, bool tx_pause, bool rx_pause); + void (*mac_disable_tx_lpi)(struct phylink_config *config); + int (*mac_enable_tx_lpi)(struct phylink_config *config, u32 timer, + bool tx_clk_stop); }; #if 0 /* For kernel-doc purposes only. */ /** - * validate - Validate and update the link configuration + * mac_get_caps: Get MAC capabilities for interface mode. * @config: a pointer to a &struct phylink_config. - * @supported: ethtool bitmask for supported link modes. - * @state: a pointer to a &struct phylink_link_state. - * - * Clear bits in the @supported and @state->advertising masks that - * are not supportable by the MAC. - * - * Note that the PHY may be able to transform from one connection - * technology to another, so, eg, don't clear 1000BaseX just - * because the MAC is unable to BaseX mode. This is more about - * clearing unsupported speeds and duplex settings. The port modes - * should not be cleared; phylink_set_port_modes() will help with this. + * @interface: PHY interface mode. * - * If the @state->interface mode is %PHY_INTERFACE_MODE_1000BASEX - * or %PHY_INTERFACE_MODE_2500BASEX, select the appropriate mode - * based on @state->advertising and/or @state->speed and update - * @state->interface accordingly. See phylink_helper_basex_speed(). - * - * When @state->interface is %PHY_INTERFACE_MODE_NA, phylink expects the - * MAC driver to return all supported link modes. - * - * If the @state->interface mode is not supported, then the @supported - * mask must be cleared. + * Optional method. When not provided, config->mac_capabilities will be used. + * When implemented, this returns the MAC capabilities for the specified + * interface mode where there is some special handling required by the MAC + * driver (e.g. not supporting half-duplex in certain interface modes.) */ -void validate(struct phylink_config *config, unsigned long *supported, - struct phylink_link_state *state); - +unsigned long mac_get_caps(struct phylink_config *config, + phy_interface_t interface); /** - * mac_pcs_get_state() - Read the current inband link state from the hardware + * mac_select_pcs: Select a PCS for the interface mode. * @config: a pointer to a &struct phylink_config. - * @state: a pointer to a &struct phylink_link_state. + * @interface: PHY interface mode for PCS * - * Read the current inband link state from the MAC PCS, reporting the - * current speed in @state->speed, duplex mode in @state->duplex, pause - * mode in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits, - * negotiation completion state in @state->an_complete, and link up state - * in @state->link. If possible, @state->lp_advertising should also be - * populated. + * Return the &struct phylink_pcs for the specified interface mode, or + * NULL if none is required, or an error pointer on error. + * + * This must not modify any state. It is used to query which PCS should + * be used. Phylink will use this during validation to ensure that the + * configuration is valid, and when setting a configuration to internally + * set the PCS that will be used. */ -void mac_pcs_get_state(struct phylink_config *config, - struct phylink_link_state *state); +struct phylink_pcs *mac_select_pcs(struct phylink_config *config, + phy_interface_t interface); /** * mac_prepare() - prepare to change the PHY interface mode @@ -191,8 +278,9 @@ int mac_prepare(struct phylink_config *config, unsigned int mode, * guaranteed to be correct, and so any mac_config() implementation must * never reference these fields. * - * (this requires a rewrite - please refer to mac_link_up() for situations - * where the PCS and MAC are not tightly integrated.) + * This will only be called to reconfigure the MAC for a "major" change in + * e.g. interface mode. It will not be called for changes in speed, duplex + * or pause modes or to change the in-band advertisement. * * In all negotiation modes, as defined by @mode, @state->pause indicates the * pause settings which should be applied as follows. If %MLO_PAUSE_AN is not @@ -224,7 +312,7 @@ int mac_prepare(struct phylink_config *config, unsigned int mode, * 1000base-X or Cisco SGMII mode depending on the @state->interface * mode). In both cases, link state management (whether the link * is up or not) is performed by the MAC, and reported via the - * mac_pcs_get_state() callback. Changes in link state must be made + * pcs_get_state() callback. Changes in link state must be made * by calling phylink_mac_change(). * * Interface mode specific details are mentioned below. @@ -273,29 +361,29 @@ int mac_finish(struct phylink_config *config, unsigned int mode, phy_interface_t iface); /** - * mac_an_restart() - restart 802.3z BaseX autonegotiation - * @config: a pointer to a &struct phylink_config. - */ -void mac_an_restart(struct phylink_config *config); - -/** - * mac_link_down() - take the link down + * mac_link_down() - notification that the link has gone down * @config: a pointer to a &struct phylink_config. * @mode: link autonegotiation mode * @interface: link &typedef phy_interface_t mode * - * If @mode is not an in-band negotiation mode (as defined by - * phylink_autoneg_inband()), force the link down and disable any - * Energy Efficient Ethernet MAC configuration. Interface type - * selection must be done in mac_config(). + * Notifies the MAC that the link has gone down. This will not be called + * unless mac_link_up() has been previously called. + * + * The MAC should stop processing packets for transmission and reception. + * phylink will have called netif_carrier_off() to notify the networking + * stack that the link has gone down, so MAC drivers should not make this + * call. + * + * If @mode is %MLO_AN_INBAND, then this function must not prevent the + * link coming up. */ void mac_link_down(struct phylink_config *config, unsigned int mode, phy_interface_t interface); /** - * mac_link_up() - allow the link to come up + * mac_link_up() - notification that the link has come up * @config: a pointer to a &struct phylink_config. - * @phy: any attached phy + * @phy: any attached phy (deprecated - please use LPI interfaces) * @mode: link autonegotiation mode * @interface: link &typedef phy_interface_t mode * @speed: link speed @@ -303,7 +391,10 @@ void mac_link_down(struct phylink_config *config, unsigned int mode, * @tx_pause: link transmit pause enablement status * @rx_pause: link receive pause enablement status * - * Configure the MAC for an established link. + * Notifies the MAC that the link has come up, and the parameters of the + * link as seen from the MACs point of view. If mac_link_up() has been + * called previously, there will be an intervening call to mac_link_down() + * before this method will be subsequently called. * * @speed, @duplex, @tx_pause and @rx_pause indicate the finalised link * settings, and should be used to configure the MAC block appropriately @@ -315,55 +406,164 @@ void mac_link_down(struct phylink_config *config, unsigned int mode, * that the user wishes to override the pause settings, and this should * be allowed when considering the implementation of this method. * - * If in-band negotiation mode is disabled, allow the link to come up. If - * @phy is non-%NULL, configure Energy Efficient Ethernet by calling - * phy_init_eee() and perform appropriate MAC configuration for EEE. + * Once configured, the MAC may begin to process packets for transmission + * and reception. + * * Interface type selection must be done in mac_config(). */ void mac_link_up(struct phylink_config *config, struct phy_device *phy, unsigned int mode, phy_interface_t interface, int speed, int duplex, bool tx_pause, bool rx_pause); + +/** + * mac_disable_tx_lpi() - disable LPI generation at the MAC + * @config: a pointer to a &struct phylink_config. + * + * Disable generation of LPI at the MAC, effectively preventing the MAC + * from indicating that it is idle. + */ +void mac_disable_tx_lpi(struct phylink_config *config); + +/** + * mac_enable_tx_lpi() - configure and enable LPI generation at the MAC + * @config: a pointer to a &struct phylink_config. + * @timer: LPI timeout in microseconds. + * @tx_clk_stop: allow xMII transmit clock to be stopped during LPI + * + * Configure the LPI timeout accordingly. This will only be called when + * the link is already up, to cater for situations where the hardware + * needs to be programmed according to the link speed. + * + * Enable LPI generation at the MAC, and configure whether the xMII transmit + * clock may be stopped. + * + * Returns: 0 on success. Please consult with rmk before returning an error. + */ +int mac_enable_tx_lpi(struct phylink_config *config, u32 timer, + bool tx_clk_stop); #endif struct phylink_pcs_ops; /** * struct phylink_pcs - PHYLINK PCS instance + * @supported_interfaces: describing which PHY_INTERFACE_MODE_xxx + * are supported by this PCS. * @ops: a pointer to the &struct phylink_pcs_ops structure + * @phylink: pointer to &struct phylink_config * @poll: poll the PCS for link changes + * @rxc_always_on: The MAC driver requires the reference clock + * to always be on. Standalone PCS drivers which + * do not have access to a PHY device can check + * this instead of PHY_F_RXC_ALWAYS_ON. * * This structure is designed to be embedded within the PCS private data, * and will be passed between phylink and the PCS. + * + * The @phylink member is private to phylink and must not be touched by + * the PCS driver. */ struct phylink_pcs { + DECLARE_PHY_INTERFACE_MASK(supported_interfaces); const struct phylink_pcs_ops *ops; + struct phylink *phylink; bool poll; + bool rxc_always_on; }; /** * struct phylink_pcs_ops - MAC PCS operations structure. + * @pcs_validate: validate the link configuration. + * @pcs_inband_caps: query inband support for interface mode. + * @pcs_enable: enable the PCS. + * @pcs_disable: disable the PCS. + * @pcs_pre_config: pre-mac_config method (for errata) + * @pcs_post_config: post-mac_config method (for arrata) * @pcs_get_state: read the current MAC PCS link state from the hardware. * @pcs_config: configure the MAC PCS for the selected mode and state. * @pcs_an_restart: restart 802.3z BaseX autonegotiation. * @pcs_link_up: program the PCS for the resolved link configuration * (where necessary). + * @pcs_disable_eee: optional notification to PCS that EEE has been disabled + * at the MAC. + * @pcs_enable_eee: optional notification to PCS that EEE will be enabled at + * the MAC. + * @pcs_pre_init: configure PCS components necessary for MAC hardware + * initialization e.g. RX clock for stmmac. */ struct phylink_pcs_ops { - void (*pcs_get_state)(struct phylink_pcs *pcs, + int (*pcs_validate)(struct phylink_pcs *pcs, unsigned long *supported, + const struct phylink_link_state *state); + unsigned int (*pcs_inband_caps)(struct phylink_pcs *pcs, + phy_interface_t interface); + int (*pcs_enable)(struct phylink_pcs *pcs); + void (*pcs_disable)(struct phylink_pcs *pcs); + void (*pcs_pre_config)(struct phylink_pcs *pcs, + phy_interface_t interface); + int (*pcs_post_config)(struct phylink_pcs *pcs, + phy_interface_t interface); + void (*pcs_get_state)(struct phylink_pcs *pcs, unsigned int neg_mode, struct phylink_link_state *state); - int (*pcs_config)(struct phylink_pcs *pcs, unsigned int mode, + int (*pcs_config)(struct phylink_pcs *pcs, unsigned int neg_mode, phy_interface_t interface, const unsigned long *advertising, bool permit_pause_to_mac); void (*pcs_an_restart)(struct phylink_pcs *pcs); - void (*pcs_link_up)(struct phylink_pcs *pcs, unsigned int mode, + void (*pcs_link_up)(struct phylink_pcs *pcs, unsigned int neg_mode, phy_interface_t interface, int speed, int duplex); + void (*pcs_disable_eee)(struct phylink_pcs *pcs); + void (*pcs_enable_eee)(struct phylink_pcs *pcs); + int (*pcs_pre_init)(struct phylink_pcs *pcs); }; #if 0 /* For kernel-doc purposes only. */ /** + * pcs_validate() - validate the link configuration. + * @pcs: a pointer to a &struct phylink_pcs. + * @supported: ethtool bitmask for supported link modes. + * @state: a const pointer to a &struct phylink_link_state. + * + * Validate the interface mode, and advertising's autoneg bit, removing any + * media ethtool link modes that would not be supportable from the supported + * mask. Phylink will propagate the changes to the advertising mask. See the + * &struct phylink_mac_ops validate() method. + * + * Returns -EINVAL if the interface mode/autoneg mode is not supported. + * Returns non-zero positive if the link state can be supported. + */ +int pcs_validate(struct phylink_pcs *pcs, unsigned long *supported, + const struct phylink_link_state *state); + +/** + * pcs_inband_caps - query PCS in-band capabilities for interface mode. + * @pcs: a pointer to a &struct phylink_pcs. + * @interface: interface mode to be queried + * + * Returns zero if it is unknown what in-band signalling is supported by the + * PHY (e.g. because the PHY driver doesn't implement the method.) Otherwise, + * returns a bit mask of the LINK_INBAND_* values from + * &enum link_inband_signalling to describe which inband modes are supported + * for this interface mode. + */ +unsigned int pcs_inband_caps(struct phylink_pcs *pcs, + phy_interface_t interface); + +/** + * pcs_enable() - enable the PCS. + * @pcs: a pointer to a &struct phylink_pcs. + */ +int pcs_enable(struct phylink_pcs *pcs); + +/** + * pcs_disable() - disable the PCS. + * @pcs: a pointer to a &struct phylink_pcs. + */ +void pcs_disable(struct phylink_pcs *pcs); + +/** * pcs_get_state() - Read the current inband link state from the hardware * @pcs: a pointer to a &struct phylink_pcs. + * @neg_mode: link negotiation mode (PHYLINK_PCS_NEG_xxx) * @state: a pointer to a &struct phylink_link_state. * * Read the current inband link state from the MAC PCS, reporting the @@ -373,16 +573,16 @@ struct phylink_pcs_ops { * in @state->link. If possible, @state->lp_advertising should also be * populated. * - * When present, this overrides mac_pcs_get_state() in &struct - * phylink_mac_ops. + * Note that the @neg_mode parameter is always the PHYLINK_PCS_NEG_xxx + * state, not MLO_AN_xxx. */ -void pcs_get_state(struct phylink_pcs *pcs, +void pcs_get_state(struct phylink_pcs *pcs, unsigned int neg_mode, struct phylink_link_state *state); /** * pcs_config() - Configure the PCS mode and advertisement * @pcs: a pointer to a &struct phylink_pcs. - * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND. + * @neg_mode: link negotiation mode (see below) * @interface: interface mode to be used * @advertising: adertisement ethtool link mode mask * @permit_pause_to_mac: permit forwarding pause resolution to MAC @@ -400,8 +600,20 @@ void pcs_get_state(struct phylink_pcs *pcs, * For 1000BASE-X, the advertisement should be programmed into the PCS. * * For most 10GBASE-R, there is no advertisement. + * + * The %neg_mode argument should be tested via the phylink_mode_*() family of + * functions, or for PCS that set pcs->neg_mode true, should be tested + * against the PHYLINK_PCS_NEG_* definitions. + * + * pcs_config() will be called when configuration of the PCS is required + * or when the advertisement is possibly updated. It must not unnecessarily + * disrupt an established link. + * + * When an autonegotiation restart is required for 802.3z modes, .pcs_config() + * should return a positive non-zero integer (e.g. 1) to indicate to phylink + * to call the pcs_an_restart() method. */ -int pcs_config(struct phylink_pcs *pcs, unsigned int mode, +int pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode, phy_interface_t interface, const unsigned long *advertising, bool permit_pause_to_mac); @@ -417,7 +629,7 @@ void pcs_an_restart(struct phylink_pcs *pcs); /** * pcs_link_up() - program the PCS for the resolved link configuration * @pcs: a pointer to a &struct phylink_pcs. - * @mode: link autonegotiation mode + * @neg_mode: link negotiation mode (see below) * @interface: link &typedef phy_interface_t mode * @speed: link speed * @duplex: link duplex @@ -426,26 +638,90 @@ void pcs_an_restart(struct phylink_pcs *pcs); * the resolved link parameters. For example, a PCS operating in SGMII * mode without in-band AN needs to be manually configured for the link * and duplex setting. Otherwise, this should be a no-op. + * + * The %mode argument should be tested via the phylink_mode_*() family of + * functions, or for PCS that set pcs->neg_mode true, should be tested + * against the PHYLINK_PCS_NEG_* definitions. */ -void pcs_link_up(struct phylink_pcs *pcs, unsigned int mode, +void pcs_link_up(struct phylink_pcs *pcs, unsigned int neg_mode, phy_interface_t interface, int speed, int duplex); + +/** + * pcs_disable_eee() - Disable EEE at the PCS + * @pcs: a pointer to a &struct phylink_pcs + * + * Optional method informing the PCS that EEE has been disabled at the MAC. + */ +void pcs_disable_eee(struct phylink_pcs *pcs); + +/** + * pcs_enable_eee() - Enable EEE at the PCS + * @pcs: a pointer to a &struct phylink_pcs + * + * Optional method informing the PCS that EEE is about to be enabled at the MAC. + */ +void pcs_enable_eee(struct phylink_pcs *pcs); + +/** + * pcs_pre_init() - Configure PCS components necessary for MAC initialization + * @pcs: a pointer to a &struct phylink_pcs. + * + * This function can be called by MAC drivers through the + * phylink_pcs_pre_init() wrapper, before their hardware is initialized. It + * should not be called after the link is brought up, as reconfiguring the PCS + * at this point could break the link. + * + * Some MAC devices require specific hardware initialization to be performed by + * their associated PCS device before they can properly initialize their own + * hardware. An example of this is the initialization of stmmac controllers, + * which requires an active REF_CLK signal to be provided by the PHY/PCS. + * + * By calling phylink_pcs_pre_init(), MAC drivers can ensure that the PCS is + * setup in a way that allows for successful hardware initialization. + * + * The specific configuration performed by pcs_pre_init() is dependent on the + * model of PCS and the requirements of the MAC device attached to it. PCS + * driver authors should consider whether their target device is to be used in + * conjunction with a MAC device whose driver calls phylink_pcs_pre_init(). MAC + * driver authors should document their requirements for the PCS + * pre-initialization. + * + */ +int pcs_pre_init(struct phylink_pcs *pcs); + #endif -struct phylink *phylink_create(struct phylink_config *, struct fwnode_handle *, - phy_interface_t iface, - const struct phylink_mac_ops *mac_ops); -void phylink_set_pcs(struct phylink *, struct phylink_pcs *pcs); +struct phylink *phylink_create(struct phylink_config *, + const struct fwnode_handle *, + phy_interface_t, + const struct phylink_mac_ops *); void phylink_destroy(struct phylink *); +bool phylink_expects_phy(struct phylink *pl); int phylink_connect_phy(struct phylink *, struct phy_device *); int phylink_of_phy_connect(struct phylink *, struct device_node *, u32 flags); +int phylink_fwnode_phy_connect(struct phylink *pl, + const struct fwnode_handle *fwnode, + u32 flags); void phylink_disconnect_phy(struct phylink *); +int phylink_set_fixed_link(struct phylink *, + const struct phylink_link_state *); void phylink_mac_change(struct phylink *, bool up); +void phylink_pcs_change(struct phylink_pcs *, bool up); + +int phylink_pcs_pre_init(struct phylink *pl, struct phylink_pcs *pcs); void phylink_start(struct phylink *); void phylink_stop(struct phylink *); +void phylink_rx_clk_stop_block(struct phylink *); +void phylink_rx_clk_stop_unblock(struct phylink *); + +void phylink_suspend(struct phylink *pl, bool mac_wol); +void phylink_prepare_resume(struct phylink *pl); +void phylink_resume(struct phylink *pl); + void phylink_ethtool_get_wol(struct phylink *, struct ethtool_wolinfo *); int phylink_ethtool_set_wol(struct phylink *, struct ethtool_wolinfo *); @@ -459,9 +735,8 @@ void phylink_ethtool_get_pauseparam(struct phylink *, int phylink_ethtool_set_pauseparam(struct phylink *, struct ethtool_pauseparam *); int phylink_get_eee_err(struct phylink *); -int phylink_init_eee(struct phylink *, bool); -int phylink_ethtool_get_eee(struct phylink *, struct ethtool_eee *); -int phylink_ethtool_set_eee(struct phylink *, struct ethtool_eee *); +int phylink_ethtool_get_eee(struct phylink *link, struct ethtool_keee *eee); +int phylink_ethtool_set_eee(struct phylink *link, struct ethtool_keee *eee); int phylink_mii_ioctl(struct phylink *, struct ifreq *, int); int phylink_speed_down(struct phylink *pl, bool sync); int phylink_speed_up(struct phylink *pl); @@ -476,18 +751,59 @@ int phylink_speed_up(struct phylink *pl); #define phylink_test(bm, mode) __phylink_do_bit(test_bit, bm, mode) void phylink_set_port_modes(unsigned long *bits); -void phylink_helper_basex_speed(struct phylink_link_state *state); +/** + * phylink_get_link_timer_ns - return the PCS link timer value + * @interface: link &typedef phy_interface_t mode + * + * Return the PCS link timer setting in nanoseconds for the PHY @interface + * mode, or -EINVAL if not appropriate. + */ +static inline int phylink_get_link_timer_ns(phy_interface_t interface) +{ + switch (interface) { + case PHY_INTERFACE_MODE_SGMII: + case PHY_INTERFACE_MODE_QSGMII: + case PHY_INTERFACE_MODE_USXGMII: + case PHY_INTERFACE_MODE_10G_QXGMII: + return 1600000; + + case PHY_INTERFACE_MODE_1000BASEX: + case PHY_INTERFACE_MODE_2500BASEX: + return 10000000; + + default: + return -EINVAL; + } +} + +/** + * phylink_mac_implements_lpi() - determine if MAC implements LPI ops + * @ops: phylink_mac_ops structure + * + * Returns true if the phylink MAC operations structure indicates that the + * LPI operations have been implemented, false otherwise. + */ +static inline bool phylink_mac_implements_lpi(const struct phylink_mac_ops *ops) +{ + return ops && ops->mac_disable_tx_lpi && ops->mac_enable_tx_lpi; +} + +void phylink_mii_c22_pcs_decode_state(struct phylink_link_state *state, + unsigned int neg_mode, u16 bmsr, u16 lpa); void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs, + unsigned int neg_mode, struct phylink_link_state *state); -int phylink_mii_c22_pcs_set_advertisement(struct mdio_device *pcs, - phy_interface_t interface, - const unsigned long *advertising); -int phylink_mii_c22_pcs_config(struct mdio_device *pcs, unsigned int mode, +int phylink_mii_c22_pcs_encode_advertisement(phy_interface_t interface, + const unsigned long *advertising); +int phylink_mii_c22_pcs_config(struct mdio_device *pcs, phy_interface_t interface, - const unsigned long *advertising); + const unsigned long *advertising, + unsigned int neg_mode); void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs); +void phylink_resolve_c73(struct phylink_link_state *state); + void phylink_mii_c45_pcs_get_state(struct mdio_device *pcs, struct phylink_link_state *state); |