diff options
Diffstat (limited to 'include/scsi/scsi_proto.h')
| -rw-r--r-- | include/scsi/scsi_proto.h | 166 |
1 files changed, 130 insertions, 36 deletions
diff --git a/include/scsi/scsi_proto.h b/include/scsi/scsi_proto.h index c36860111932..f64385cde5b9 100644 --- a/include/scsi/scsi_proto.h +++ b/include/scsi/scsi_proto.h @@ -10,6 +10,7 @@ #ifndef _SCSI_PROTO_H_ #define _SCSI_PROTO_H_ +#include <linux/build_bug.h> #include <linux/types.h> /* @@ -32,8 +33,8 @@ #define INQUIRY 0x12 #define RECOVER_BUFFERED_DATA 0x14 #define MODE_SELECT 0x15 -#define RESERVE 0x16 -#define RELEASE 0x17 +#define RESERVE_6 0x16 +#define RELEASE_6 0x17 #define COPY 0x18 #define ERASE 0x19 #define MODE_SENSE 0x1a @@ -119,6 +120,7 @@ #define WRITE_SAME_16 0x93 #define ZBC_OUT 0x94 #define ZBC_IN 0x95 +#define WRITE_ATOMIC_16 0x9c #define SERVICE_ACTION_BIDIRECTIONAL 0x9d #define SERVICE_ACTION_IN_16 0x9e #define SERVICE_ACTION_OUT_16 0x9f @@ -126,6 +128,7 @@ #define SAI_READ_CAPACITY_16 0x10 #define SAI_GET_LBA_STATUS 0x12 #define SAI_REPORT_REFERRALS 0x13 +#define SAI_GET_STREAM_STATUS 0x16 /* values for maintenance in */ #define MI_REPORT_IDENTIFYING_INFORMATION 0x05 #define MI_REPORT_TARGET_PGS 0x0a @@ -151,6 +154,11 @@ #define ZO_FINISH_ZONE 0x02 #define ZO_OPEN_ZONE 0x03 #define ZO_RESET_WRITE_POINTER 0x04 +/* values for PR in service action */ +#define READ_KEYS 0x00 +#define READ_RESERVATION 0x01 +#define REPORT_CAPABILITES 0x02 +#define READ_FULL_STATUS 0x03 /* values for variable length command */ #define XDREAD_32 0x03 #define XDWRITE_32 0x04 @@ -190,43 +198,25 @@ struct scsi_varlen_cdb_hdr { * SCSI Architecture Model (SAM) Status codes. Taken from SAM-3 draft * T10/1561-D Revision 4 Draft dated 7th November 2002. */ -#define SAM_STAT_GOOD 0x00 -#define SAM_STAT_CHECK_CONDITION 0x02 -#define SAM_STAT_CONDITION_MET 0x04 -#define SAM_STAT_BUSY 0x08 -#define SAM_STAT_INTERMEDIATE 0x10 -#define SAM_STAT_INTERMEDIATE_CONDITION_MET 0x14 -#define SAM_STAT_RESERVATION_CONFLICT 0x18 -#define SAM_STAT_COMMAND_TERMINATED 0x22 /* obsolete in SAM-3 */ -#define SAM_STAT_TASK_SET_FULL 0x28 -#define SAM_STAT_ACA_ACTIVE 0x30 -#define SAM_STAT_TASK_ABORTED 0x40 - -/* - * Status codes. These are deprecated as they are shifted 1 bit right - * from those found in the SCSI standards. This causes confusion for - * applications that are ported to several OSes. Prefer SAM Status codes - * above. - */ - -#define GOOD 0x00 -#define CHECK_CONDITION 0x01 -#define CONDITION_GOOD 0x02 -#define BUSY 0x04 -#define INTERMEDIATE_GOOD 0x08 -#define INTERMEDIATE_C_GOOD 0x0a -#define RESERVATION_CONFLICT 0x0c -#define COMMAND_TERMINATED 0x11 -#define QUEUE_FULL 0x14 -#define ACA_ACTIVE 0x18 -#define TASK_ABORTED 0x20 +enum sam_status { + SAM_STAT_GOOD = 0x00, + SAM_STAT_CHECK_CONDITION = 0x02, + SAM_STAT_CONDITION_MET = 0x04, + SAM_STAT_BUSY = 0x08, + SAM_STAT_INTERMEDIATE = 0x10, + SAM_STAT_INTERMEDIATE_CONDITION_MET = 0x14, + SAM_STAT_RESERVATION_CONFLICT = 0x18, + SAM_STAT_COMMAND_TERMINATED = 0x22, /* obsolete in SAM-3 */ + SAM_STAT_TASK_SET_FULL = 0x28, + SAM_STAT_ACA_ACTIVE = 0x30, + SAM_STAT_TASK_ABORTED = 0x40, +}; -#define STATUS_MASK 0xfe +#define STATUS_MASK 0xfe /* * SENSE KEYS */ - #define NO_SENSE 0x00 #define RECOVERED_ERROR 0x01 #define NOT_READY 0x02 @@ -241,7 +231,7 @@ struct scsi_varlen_cdb_hdr { #define ABORTED_COMMAND 0x0b #define VOLUME_OVERFLOW 0x0d #define MISCOMPARE 0x0e - +#define COMPLETED 0x0f /* * DEVICE TYPES @@ -288,6 +278,81 @@ struct scsi_lun { __u8 scsi_lun[8]; }; +/* SBC-5 IO advice hints group descriptor */ +struct scsi_io_group_descriptor { +#if defined(__BIG_ENDIAN) + u8 io_advice_hints_mode: 2; + u8 reserved1: 3; + u8 st_enble: 1; + u8 cs_enble: 1; + u8 ic_enable: 1; +#elif defined(__LITTLE_ENDIAN) + u8 ic_enable: 1; + u8 cs_enble: 1; + u8 st_enble: 1; + u8 reserved1: 3; + u8 io_advice_hints_mode: 2; +#else +#error +#endif + u8 reserved2[3]; + /* Logical block markup descriptor */ +#if defined(__BIG_ENDIAN) + u8 acdlu: 1; + u8 reserved3: 1; + u8 rlbsr: 2; + u8 lbm_descriptor_type: 4; +#elif defined(__LITTLE_ENDIAN) + u8 lbm_descriptor_type: 4; + u8 rlbsr: 2; + u8 reserved3: 1; + u8 acdlu: 1; +#else +#error +#endif + u8 params[2]; + u8 reserved4; + u8 reserved5[8]; +}; + +static_assert(sizeof(struct scsi_io_group_descriptor) == 16); + +/* SCSI stream status descriptor */ +struct scsi_stream_status { +#if defined(__BIG_ENDIAN) + u8 perm: 1; + u8 reserved1: 7; +#elif defined(__LITTLE_ENDIAN) + u8 reserved1: 7; + u8 perm: 1; +#else +#error +#endif + u8 reserved2; + __be16 stream_identifier; +#if defined(__BIG_ENDIAN) + u8 reserved3: 2; + u8 rel_lifetime: 6; +#elif defined(__LITTLE_ENDIAN) + u8 rel_lifetime: 6; + u8 reserved3: 2; +#else +#error +#endif + u8 reserved4[3]; +}; + +static_assert(sizeof(struct scsi_stream_status) == 8); + +/* GET STREAM STATUS parameter data */ +struct scsi_stream_status_header { + __be32 len; /* length in bytes of following payload */ + u16 reserved; + __be16 number_of_open_streams; +}; + +static_assert(sizeof(struct scsi_stream_status_header) == 8); + /* SPC asymmetric access states */ #define SCSI_ACCESS_STATE_OPTIMAL 0x00 #define SCSI_ACCESS_STATE_ACTIVE 0x01 @@ -325,7 +390,9 @@ enum zbc_zone_type { ZBC_ZONE_TYPE_CONV = 0x1, ZBC_ZONE_TYPE_SEQWRITE_REQ = 0x2, ZBC_ZONE_TYPE_SEQWRITE_PREF = 0x3, - /* 0x4 to 0xf are reserved */ + ZBC_ZONE_TYPE_SEQ_OR_BEFORE_REQ = 0x4, + ZBC_ZONE_TYPE_GAP = 0x5, + /* 0x6 to 0xf are reserved */ }; /* Zone conditions of REPORT ZONES zone descriptors */ @@ -341,4 +408,31 @@ enum zbc_zone_cond { ZBC_ZONE_COND_OFFLINE = 0xf, }; +enum zbc_zone_alignment_method { + ZBC_CONSTANT_ZONE_LENGTH = 0x1, + ZBC_CONSTANT_ZONE_START_OFFSET = 0x8, +}; + +/* Version descriptor values for INQUIRY */ +enum scsi_version_descriptor { + SCSI_VERSION_DESCRIPTOR_FCP4 = 0x0a40, + SCSI_VERSION_DESCRIPTOR_ISCSI = 0x0960, + SCSI_VERSION_DESCRIPTOR_SAM5 = 0x00a0, + SCSI_VERSION_DESCRIPTOR_SAS3 = 0x0c60, + SCSI_VERSION_DESCRIPTOR_SBC3 = 0x04c0, + SCSI_VERSION_DESCRIPTOR_SBP3 = 0x0980, + SCSI_VERSION_DESCRIPTOR_SPC4 = 0x0460, + SCSI_VERSION_DESCRIPTOR_SRP = 0x0940 +}; + +enum scsi_support_opcode { + SCSI_SUPPORT_NO_INFO = 0, + SCSI_SUPPORT_NOT_SUPPORTED = 1, + SCSI_SUPPORT_FULL = 3, + SCSI_SUPPORT_VENDOR = 5, +}; + +#define SCSI_CONTROL_MASK 0 +#define SCSI_GROUP_NUMBER_MASK 0 + #endif /* _SCSI_PROTO_H_ */ |