diff options
Diffstat (limited to 'include/uapi/linux/spi')
| -rw-r--r-- | include/uapi/linux/spi/spi.h | 43 | ||||
| -rw-r--r-- | include/uapi/linux/spi/spidev.h | 30 |
2 files changed, 44 insertions, 29 deletions
diff --git a/include/uapi/linux/spi/spi.h b/include/uapi/linux/spi/spi.h new file mode 100644 index 000000000000..ca56e477d161 --- /dev/null +++ b/include/uapi/linux/spi/spi.h @@ -0,0 +1,43 @@ +/* SPDX-License-Identifier: GPL-2.0+ WITH Linux-syscall-note */ +#ifndef _UAPI_SPI_H +#define _UAPI_SPI_H + +#include <linux/const.h> + +#define SPI_CPHA _BITUL(0) /* clock phase */ +#define SPI_CPOL _BITUL(1) /* clock polarity */ + +#define SPI_MODE_0 (0|0) /* (original MicroWire) */ +#define SPI_MODE_1 (0|SPI_CPHA) +#define SPI_MODE_2 (SPI_CPOL|0) +#define SPI_MODE_3 (SPI_CPOL|SPI_CPHA) +#define SPI_MODE_X_MASK (SPI_CPOL|SPI_CPHA) + +#define SPI_CS_HIGH _BITUL(2) /* chipselect active high? */ +#define SPI_LSB_FIRST _BITUL(3) /* per-word bits-on-wire */ +#define SPI_3WIRE _BITUL(4) /* SI/SO signals shared */ +#define SPI_LOOP _BITUL(5) /* loopback mode */ +#define SPI_NO_CS _BITUL(6) /* 1 dev/bus, no chipselect */ +#define SPI_READY _BITUL(7) /* slave pulls low to pause */ +#define SPI_TX_DUAL _BITUL(8) /* transmit with 2 wires */ +#define SPI_TX_QUAD _BITUL(9) /* transmit with 4 wires */ +#define SPI_RX_DUAL _BITUL(10) /* receive with 2 wires */ +#define SPI_RX_QUAD _BITUL(11) /* receive with 4 wires */ +#define SPI_CS_WORD _BITUL(12) /* toggle cs after each word */ +#define SPI_TX_OCTAL _BITUL(13) /* transmit with 8 wires */ +#define SPI_RX_OCTAL _BITUL(14) /* receive with 8 wires */ +#define SPI_3WIRE_HIZ _BITUL(15) /* high impedance turnaround */ +#define SPI_RX_CPHA_FLIP _BITUL(16) /* flip CPHA on Rx only xfer */ +#define SPI_MOSI_IDLE_LOW _BITUL(17) /* leave mosi line low when idle */ + +/* + * All the bits defined above should be covered by SPI_MODE_USER_MASK. + * The SPI_MODE_USER_MASK has the SPI_MODE_KERNEL_MASK counterpart in + * 'include/linux/spi/spi.h'. The bits defined here are from bit 0 upwards + * while in SPI_MODE_KERNEL_MASK they are from the other end downwards. + * These bits must not overlap. A static assert check should make sure of that. + * If adding extra bits, make sure to increase the bit index below as well. + */ +#define SPI_MODE_USER_MASK (_BITUL(18) - 1) + +#endif /* _UAPI_SPI_H */ diff --git a/include/uapi/linux/spi/spidev.h b/include/uapi/linux/spi/spidev.h index d56427c0b3e0..0c3da08f2aff 100644 --- a/include/uapi/linux/spi/spidev.h +++ b/include/uapi/linux/spi/spidev.h @@ -25,35 +25,7 @@ #include <linux/types.h> #include <linux/ioctl.h> - -/* User space versions of kernel symbols for SPI clocking modes, - * matching <linux/spi/spi.h> - */ - -#define SPI_CPHA 0x01 -#define SPI_CPOL 0x02 - -#define SPI_MODE_0 (0|0) -#define SPI_MODE_1 (0|SPI_CPHA) -#define SPI_MODE_2 (SPI_CPOL|0) -#define SPI_MODE_3 (SPI_CPOL|SPI_CPHA) - -#define SPI_CS_HIGH 0x04 -#define SPI_LSB_FIRST 0x08 -#define SPI_3WIRE 0x10 -#define SPI_LOOP 0x20 -#define SPI_NO_CS 0x40 -#define SPI_READY 0x80 -#define SPI_TX_DUAL 0x100 -#define SPI_TX_QUAD 0x200 -#define SPI_RX_DUAL 0x400 -#define SPI_RX_QUAD 0x800 -#define SPI_CS_WORD 0x1000 -#define SPI_TX_OCTAL 0x2000 -#define SPI_RX_OCTAL 0x4000 -#define SPI_3WIRE_HIZ 0x8000 - -/*---------------------------------------------------------------------------*/ +#include <linux/spi/spi.h> /* IOCTL commands */ |