| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With the addition of horizon feature to sch_fq, we noticed some
suboptimal behavior of extremely low pacing rate TCP flows, especially
when TCP is not aware of a drop happening in lower stacks.
Back in commit 3f80e08f40cd ("tcp: add tcp_reset_xmit_timer() helper"),
tcp_pacing_delay() was added to estimate an extra delay to add to standard
rto timers.
This patch removes the skb argument from this helper and
tcp_reset_xmit_timer() because it makes more sense to simply
consider the time at which next packet is allowed to be sent,
instead of the time of whatever packet has been sent.
This avoids arming RTO timer too soon and removes
spurious horizon drops.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the upcoming rev of RFC4941 (IPv6 temporary addresses):
https://tools.ietf.org/html/draft-ietf-6man-rfc4941bis-09
* Reduces the default Valid Lifetime to 2 days
The number of extra addresses employed when Valid Lifetime was
7 days exacerbated the stress caused on network
elements/devices. Additionally, the motivation for temporary
addresses is indeed privacy and reduced exposure. With a
default Valid Lifetime of 7 days, an address that becomes
revealed by active communication is reachable and exposed for
one whole week. The only use case for a Valid Lifetime of 7
days could be some application that is expecting to have long
lived connections. But if you want to have a long lived
connections, you shouldn't be using a temporary address in the
first place. Additionally, in the era of mobile devices, general
applications should nevertheless be prepared and robust to
address changes (e.g. nodes swap wifi <-> 4G, etc.)
* Employs different IIDs for different prefixes
To avoid network activity correlation among addresses configured
for different prefixes
* Uses a simpler algorithm for IID generation
No need to store "history" anywhere
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Type I ERSPAN frame format is based on the barebones
IP + GRE(4-byte) encapsulation on top of the raw mirrored frame.
Both type I and II use 0x88BE as protocol type. Unlike type II
and III, no sequence number or key is required.
To creat a type I erspan tunnel device:
$ ip link add dev erspan11 type erspan \
local 172.16.1.100 remote 172.16.1.200 \
erspan_ver 0
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit b3e80d44f5b1
("bonding: fix lockdep warning in bond_get_stats()") the dynamic
key is no longer necessary, as we compute nest level at run-time.
So, we can just remove it to save some lockdep key entries.
Test commands:
ip link add bond0 type bond
ip link add bond1 type bond
ip link set bond0 master bond1
ip link set bond0 nomaster
ip link set bond1 master bond0
Reported-and-tested-by: syzbot+aaa6fa4949cc5d9b7b25@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the gate action to the flow action entry. Add the gate parameters to
the tc_setup_flow_action() queueing to the entries of flow_action_entry
array provide to the driver.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a ingress frame gate control flow action.
Tc gate action does the work like this:
Assume there is a gate allow specified ingress frames can be passed at
specific time slot, and be dropped at specific time slot. Tc filter
chooses the ingress frames, and tc gate action would specify what slot
does these frames can be passed to device and what time slot would be
dropped.
Tc gate action would provide an entry list to tell how much time gate
keep open and how much time gate keep state close. Gate action also
assign a start time to tell when the entry list start. Then driver would
repeat the gate entry list cyclically.
For the software simulation, gate action requires the user assign a time
clock type.
Below is the setting example in user space. Tc filter a stream source ip
address is 192.168.0.20 and gate action own two time slots. One is last
200ms gate open let frame pass another is last 100ms gate close let
frames dropped. When the ingress frames have reach total frames over
8000000 bytes, the excessive frames will be dropped in that 200000000ns
time slot.
> tc qdisc add dev eth0 ingress
> tc filter add dev eth0 parent ffff: protocol ip \
flower src_ip 192.168.0.20 \
action gate index 2 clockid CLOCK_TAI \
sched-entry open 200000000 -1 8000000 \
sched-entry close 100000000 -1 -1
> tc chain del dev eth0 ingress chain 0
"sched-entry" follow the name taprio style. Gate state is
"open"/"close". Follow with period nanosecond. Then next item is internal
priority value means which ingress queue should put. "-1" means
wildcard. The last value optional specifies the maximum number of
MSDU octets that are permitted to pass the gate during the specified
time interval.
Base-time is not set will be 0 as default, as result start time would
be ((N + 1) * cycletime) which is the minimal of future time.
Below example shows filtering a stream with destination mac address is
10:00:80:00:00:00 and ip type is ICMP, follow the action gate. The gate
action would run with one close time slot which means always keep close.
The time cycle is total 200000000ns. The base-time would calculate by:
1357000000000 + (N + 1) * cycletime
When the total value is the future time, it will be the start time.
The cycletime here would be 200000000ns for this case.
> tc filter add dev eth0 parent ffff: protocol ip \
flower skip_hw ip_proto icmp dst_mac 10:00:80:00:00:00 \
action gate index 12 base-time 1357000000000 \
sched-entry close 200000000 -1 -1 \
clockid CLOCK_TAI
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the behavior of TCP_LINGER2 about its limit. The
sysctl_tcp_fin_timeout used to be the limit of TCP_LINGER2 but now it's
only the default value. A new macro named TCP_FIN_TIMEOUT_MAX is added
as the limit of TCP_LINGER2, which is 2 minutes.
Since TCP_LINGER2 used sysctl_tcp_fin_timeout as the default value
and the limit in the past, the system administrator cannot set the
default value for most of sockets and let some sockets have a greater
timeout. It might be a mistake that let the sysctl to be the limit of
the TCP_LINGER2. Maybe we can add a new sysctl to set the max of
TCP_LINGER2, but FIN-WAIT-2 timeout is usually no need to be too long
and 2 minutes are legal considering TCP specs.
Changes in v3:
- Remove the new socket option and change the TCP_LINGER2 behavior so
that the timeout can be set to value between sysctl_tcp_fin_timeout
and 2 minutes.
Changes in v2:
- Add int overflow check for the new socket option.
Changes in v1:
- Add a new socket option to set timeout greater than
sysctl_tcp_fin_timeout.
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add, and use in generic netlink, helpers to dump out a netlink
policy to userspace, including all the range validation data,
nested policies etc.
This lets userspace discover what the kernel understands.
For families/commands other than generic netlink, the helpers
need to be used directly in an appropriate command, or we can
add some infrastructure (a new netlink family) that those can
register their policies with for introspection. I'm not that
familiar with non-generic netlink, so that's left out for now.
The data exposed to userspace also includes min and max length
for binary/string data, I've done that instead of letting the
userspace tools figure out whether min/max is intended based
on the type so that we can extend this later in the kernel, we
might want to just use the range data for example.
Because of this, I opted to not directly expose the NLA_*
values, even if some of them are already exposed via BPF, as
with min/max length we don't need to have different types here
for NLA_BINARY/NLA_MIN_LEN/NLA_EXACT_LEN, we just make them
all NL_ATTR_TYPE_BINARY with min/max length optionally set.
Similarly, we don't really need NLA_MSECS, and perhaps can
remove it in the future - but not if we encode it into the
userspace API now. It gets mapped to NL_ATTR_TYPE_U64 here.
Note that the exposing here corresponds to the strict policy
interpretation, and NLA_UNSPEC items are omitted entirely.
To get those, change them to NLA_MIN_LEN which behaves in
exactly the same way, but is exposed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helpers to get the policy's signed/unsigned range
validation data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a validation type instead, so we can later expose
the NLA_* values to userspace for policy descriptions.
Some transformations were done with this spatch:
@@
identifier p;
expression X, L, A;
@@
struct nla_policy p[X] = {
[A] =
-{ .type = NLA_EXACT_LEN_WARN, .len = L },
+NLA_POLICY_EXACT_LEN_WARN(L),
...
};
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since NLA_MSECS is really equivalent to NLA_U64, allow
it to have range validation as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using a pointer to a struct indicating the min/max values,
extend the ability to do range validation for arbitrary
values. Small values in the s16 range can be kept in the
policy directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the netlink policy, we currently have a void *validation_data
that's pointing to different things:
* a u32 value for bitfield32,
* the netlink policy for nested/nested array
* the string for NLA_REJECT
Remove the pointer and place appropriate type-safe items in the
union instead.
While at it, completely dissolve the pointer for the bitfield32
case and just put the value there directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a sysctl to control hrtimer slack, default of 100 usec.
This gives the opportunity to reduce system overhead,
and help very short RTT flows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for nf-next:
1) Add IPS_HW_OFFLOAD status bit, from Bodong Wang.
2) Remove 128-bit limit on the set element data area, rise it
to 64 bytes.
3) Report EOPNOTSUPP for unsupported NAT types and flags.
4) Set up nft_nat flags from the control plane path.
5) Add helper functions to set up the nf_nat_range2 structure.
6) Add netmap support for nft_nat.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current route nexthop API maintains user space compatibility
with old route API by default. Dumps and netlink notifications
support both new and old API format. In systems which have
moved to the new API, this compatibility mode cancels some
of the performance benefits provided by the new nexthop API.
This patch adds new sysctl nexthop_compat_mode which is on
by default but provides the ability to turn off compatibility
mode allowing systems to run entirely with the new routing
API. Old route API behaviour and support is not modified by this
sysctl.
Uses a single sysctl to cover both ipv4 and ipv6 following
other sysctls. Covers dumps and delete notifications as
suggested by David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Used in subsequent work to skip route delete
notifications on nexthop deletes.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far, the set elements could store up to 128-bits in the data area.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Extend switchdev API to add support for MRP. The HW is notified in
following cases:
SWITCHDEV_OBJ_ID_MRP: This is used when a MRP instance is added/removed
from the MRP ring.
SWITCHDEV_OBJ_ID_RING_ROLE_MRP: This is used when the role of the node
changes. The current supported roles are MRM and MRC.
SWITCHDEV_OBJ_ID_RING_TEST_MRP: This is used when to start/stop sending
MRP_Test frames on the mrp ring ports. This is called only on nodes that have
the role MRM. In case this fails then the SW will generate the frames.
SWITCHDEV_OBJ_ID_RING_STATE_STATE: This is used when the ring changes it states
to open or closed. This is required to notify HW because the MRP_Test frame
contains the field MRP_InState which contains this information.
SWITCHDEV_ATTR_ID_MRP_PORT_STATE: This is used when the port's state is
changed. It can be in blocking/forwarding mode.
SWITCHDEV_ATTR_ID_MRP_PORT_ROLE: This is used when port's role changes. The
roles of the port can be primary/secondary. This is required to notify HW
because the MRP_Test frame contains the field MRP_PortRole that contains this
information.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In MPTCP, the receive window is shared across all subflows, because it
refers to the mptcp-level sequence space.
MPTCP receivers already place incoming packets on the mptcp socket
receive queue and will charge it to the mptcp socket rcvbuf until
userspace consumes the data.
Update __tcp_select_window to use the occupancy of the parent/mptcp
socket instead of the subflow socket in case the tcp socket is part
of a logical mptcp connection.
This commit doesn't change choice of initial window for passive or active
connections.
While it would be possible to change those as well, this adds complexity
(especially when handling MP_JOIN requests). Furthermore, the MPTCP RFC
specifically says that a MPTCP sender 'MUST NOT use the RCV.WND field
of a TCP segment at the connection level if it does not also carry a DSS
option with a Data ACK field.'
SYN/SYNACK packets do not carry a DSS option with a Data ACK field.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simple overlapping changes to linux/vermagic.h
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 877d1f6291f8 ("net: Set sk_txhash from a random number")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no callers in-tree anymore.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When fixing the initialization race, we neglected to account for
the fact that debugfs is initialized in wiphy_register(), and
some debugfs things went missing (or rather were rerooted to the
global debugfs root).
Fix this by adding debugfs entries only after wiphy_register().
This requires some changes in the rate control code since it
currently adds debugfs at alloc time, which can no longer be
done after the reordering.
Reported-by: Jouni Malinen <j@w1.fi>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Fixes: 52e04b4ce5d0 ("mac80211: fix race in ieee80211_register_hw()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200423111344.0e00d3346f12.Iadc76a03a55093d94391fc672e996a458702875d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
RFC4862 5.5.3 e) prevents received Router Advertisements from reducing
the Valid Lifetime of configured addresses to less than two hours, thus
preventing hosts from reacting to the information provided by a router
that has positive knowledge that a prefix has become invalid.
This patch makes hosts honor all Valid Lifetime values, as per
draft-gont-6man-slaac-renum-06, Section 4.2. This is meant to help
mitigate the problem discussed in draft-ietf-v6ops-slaac-renum.
Note: Attacks aiming at disabling an advertised prefix via a Valid
Lifetime of 0 are not really more harmful than other attacks
that can be performed via forged RA messages, such as those
aiming at completely disabling a next-hop router via an RA that
advertises a Router Lifetime of 0, or performing a Denial of
Service (DoS) attack by advertising illegitimate prefixes via
forged PIOs. In scenarios where RA-based attacks are of concern,
proper mitigations such as RA-Guard [RFC6105] [RFC7113] should
be implemented.
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Export the DEV_MAP_BULK_SIZE macro to the header file so that drivers
can directly use it as the maximum number of xdp_frames received in the
.ndo_xdp_xmit() callback.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
See:
https://www.rfc-editor.org/authors/rfc8781.txt
Cc: Erik Kline <ek@google.com>
Cc: Jen Linkova <furry@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Michael Haro <mharo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Fixes: c24a77edc9a7 ("ipv6: ndisc: add support for 'PREF64' dns64 prefix identifier")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP stack is dumb in how it cooks its output packets.
Depending on MAX_HEADER value, we might chose a bad ending point
for the headers.
If we align the end of TCP headers to cache line boundary, we
make sure to always use the smallest number of cache lines,
which always help.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-04-17
Here's the first bluetooth-next pull request for the 5.8 kernel:
- Added debugfs option to control MITM flag usage during pairing
- Added new BT_MODE socket option
- Added support for Qualcom QCA6390 device
- Added support for Realtek RTL8761B device
- Added support for mSBC audio codec over USB endpoints
- Added framework for Microsoft HCI vendor extensions
- Added new Read Security Information management command
- Fixes/cleanup to link layer privacy related code
- Various other smaller cleanups & fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the controller is being reset or power cycled, then the flag
HCI_LL_RPA_RESOLUTION which indicates if controller based address
resolution is active needs to be also reset.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
In case LL Privacy is supported by the controller, it is also a good
idea to use the LE Enhanced Connection Complete event for getting all
information about the new connection and its addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The list of LE features constants has gotten a bit confused. It lost the
order and gained duplicated. Clean this up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Update missing kernel-doc annotations and fix of related warnings
at 'make htmldocs'.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://lore.kernel.org/r/20200408231013.28370-1-l.rubusch@gmail.com
[fix indentation, attribute references]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The behaviour for what is considered an anycast address changed in
commit 45e4fd26683c ("ipv6: Only create RTF_CACHE routes after
encountering pmtu exception"). This now considers the first
address in a subnet where there is a route via a gateway
to be an anycast address.
This breaks path MTU discovery and traceroutes when a host in a
remote network uses the address at the start of a prefix
(eg 2600:: advertised as 2600::/48 in the DFZ) as ICMP errors
will not be sent to anycast addresses.
This patch excludes any routes with a gateway, or via point to
point links, like the behaviour previously from
rt6_is_gw_or_nonexthop in net/ipv6/route.c.
This can be tested with:
ip link add v1 type veth peer name v2
ip netns add test
ip netns exec test ip link set lo up
ip link set v2 netns test
ip link set v1 up
ip netns exec test ip link set v2 up
ip addr add 2001:db8::1/64 dev v1 nodad
ip addr add 2001:db8:100:: dev lo nodad
ip netns exec test ip addr add 2001:db8::2/64 dev v2 nodad
ip netns exec test ip route add unreachable 2001:db8:1::1
ip netns exec test ip route add 2001:db8:100::/64 via 2001:db8::1
ip netns exec test sysctl net.ipv6.conf.all.forwarding=1
ip route add 2001:db8:1::1 via 2001:db8::2
ping -I 2001:db8::1 2001:db8:1::1 -c1
ping -I 2001:db8:100:: 2001:db8:1::1 -c1
ip addr delete 2001:db8:100:: dev lo
ip netns delete test
Currently the first ping will get back a destination unreachable ICMP
error, but the second will never get a response, with "icmp6_send:
acast source" logged. After this patch, both get destination
unreachable ICMP replies.
Fixes: 45e4fd26683c ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
Signed-off-by: Tim Stallard <code@timstallard.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix warnings related to kernel-doc notation, and wording in
function description.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net, they are:
1) Fix spurious overlap condition in the rbtree tree, from Stefano Brivio.
2) Fix possible uninitialized pointer dereference in nft_lookup.
3) IDLETIMER v1 target matches the Android layout, from
Maciej Zenczykowski.
4) Dangling pointer in nf_tables_set_alloc_name, from Eric Dumazet.
5) Fix RCU warning splat in ipset find_set_type(), from Amol Grover.
6) Report EOPNOTSUPP on unsupported set flags and object types in sets.
7) Add NFT_SET_CONCAT flag to provide consistent error reporting
when users defines set with ranges in concatenations in old kernels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BT qualification test SM/MAS/PKE/BV-01-C needs us to turn off
the MITM flag when pairing, and at the same time also set the io
capability to something other than no input no output.
Currently the MITM flag is only unset when the io capability is set
to no input no output, therefore the test cannot be executed.
This patch introduces a debugfs option to force MITM flag to be
turned off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Pull 9p updates from Dominique Martinet:
"Not much new, but a few patches for this cycle:
- Fix read with O_NONBLOCK to allow incomplete read and return
immediately
- Rest is just cleanup (indent, unused field in struct, extra
semicolon)"
* tag '9p-for-5.7' of git://github.com/martinetd/linux:
net/9p: remove unused p9_req_t aux field
9p: read only once on O_NONBLOCK
9pnet: allow making incomplete read requests
9p: Remove unneeded semicolon
9p: Fix Kconfig indentation
|
|
Initialize set lookup matching element to NULL. Otherwise, the
NFT_LOOKUP_F_INV flag reverses the matching logic and it leads to
deference an uninitialized pointer to the matching element. Make sure
element data area and stateful expression are accessed if there is a
matching set element.
This patch undoes 24791b9aa1ab ("netfilter: nft_set_bitmap: initialize set
element extension in lookups") which is not required anymore.
Fixes: 339706bc21c1 ("netfilter: nft_lookup: update element stateful expression")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch assigns the next free HCI device identifier to Bluetooth
devices based on VIRTIO devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
To allow userspace to make correcty security policy decision, the kernel
needs to export a few details of the supported security features and
encryption key size information. This command exports this information
and also allows future extensions if needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
With the Read Local Simple Pairing Options command it is possible to
retrieve the support for max encryption key size supported by the
controller and also if the controller correctly verifies the ECDH public
key during pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Micrsoft defined a set for HCI vendor extensions. Check the following
link for details:
https://docs.microsoft.com/en-us/windows-hardware/drivers/bluetooth/microsoft-defined-bluetooth-hci-commands-and-events
This provides the basic framework to enable the extension and read its
supported features. Drivers still have to declare support for this
extension before it can be utilized by the host stack.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
notifying using HCI_NOTIFY_CONN_ADD for SCO connection is generic in
case of mSBC audio. To differntiate SCO air mode introducing
HCI_NOTIFY_ENABLE_SCO_CVSD and HCI_NOTIFY_ENABLE_SCO_TRANSP.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
This adds BT_MODE socket option which can be used to set L2CAP modes,
including modes only supported over LE which were not supported using
the L2CAP_OPTIONS.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
|
|
Pull Kbuild updates from Masahiro Yamada:
"Build system:
- add CONFIG_UNUSED_KSYMS_WHITELIST, which will be useful to define a
fixed set of export symbols for Generic Kernel Image (GKI)
- allow to run 'make dt_binding_check' without .config
- use full schema for checking DT examples in *.yaml files
- make modpost fail for missing MODULE_IMPORT_NS(), which makes more
sense because we know the produced modules are never loadable
- Remove unused 'AS' variable
Kconfig:
- sanitize DEFCONFIG_LIST, and remove ARCH_DEFCONFIG from Kconfig
files
- relax the 'imply' behavior so that symbols implied by 'y' can
become 'm'
- make 'imply' obey 'depends on' in order to make 'imply' really weak
Misc:
- add documentation on building the kernel with Clang/LLVM
- revive __HAVE_ARCH_STRLEN for 32bit sparc to use optimized strlen()
- fix warning from deb-pkg builds when CONFIG_DEBUG_INFO=n
- various script and Makefile cleanups"
* tag 'kbuild-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
Makefile: Update kselftest help information
kbuild: deb-pkg: fix warning when CONFIG_DEBUG_INFO is unset
kbuild: add outputmakefile to no-dot-config-targets
kbuild: remove AS variable
net: wan: wanxl: refactor the firmware rebuild rule
net: wan: wanxl: use $(M68KCC) instead of $(M68KAS) for rebuilding firmware
net: wan: wanxl: use allow to pass CROSS_COMPILE_M68k for rebuilding firmware
kbuild: add comment about grouped target
kbuild: add -Wall to KBUILD_HOSTCXXFLAGS
kconfig: remove unused variable in qconf.cc
sparc: revive __HAVE_ARCH_STRLEN for 32bit sparc
kbuild: refactor Makefile.dtbinst more
kbuild: compute the dtbs_install destination more simply
Makefile: disallow data races on gcc-10 as well
kconfig: make 'imply' obey the direct dependency
kconfig: allow symbols implied by y to become m
net: drop_monitor: use IS_REACHABLE() to guard net_dm_hw_report()
modpost: return error if module is missing ns imports and MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS=n
modpost: rework and consolidate logging interface
kbuild: allow to run dt_binding_check without kernel configuration
...
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Add support to specify a stateful expression in set definitions,
this allows users to specify e.g. counters per set elements.
2) Flowtable software counter support.
3) Flowtable hardware offload counter support, from wenxu.
3) Parallelize flowtable hardware offload requests, from Paul Blakey.
This includes a patch to add one work entry per offload command.
4) Several patches to rework nf_queue refcount handling, from Florian
Westphal.
4) A few fixes for the flowtable tunnel offload: Fix crash if tunneling
information is missing and set up indirect flow block as TC_SETUP_FT,
patch from wenxu.
5) Stricter netlink attribute sanity check on filters, from Romain Bellan
and Florent Fourcot.
5) Annotations to make sparse happy, from Jules Irenge.
6) Improve icmp errors in debugging information, from Haishuang Yan.
7) Fix warning in IPVS icmp error debugging, from Haishuang Yan.
8) Fix endianess issue in tcp extension header, from Sergey Marinkevich.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Eric Dumazet
Fernando Gont
William Tu
Cong Wang
Po Liu
Cambda Zhu
Johannes Berg
Mauro Carvalho Chehab
David S. Miller
Roopa Prabhu
Pablo Neira Ayuso
Horatiu Vultur
Florian Westphal
YueHaibing
Ioana Ciornei
Maciej Żenczykowski
Marcel Holtmann
Lothar Rubusch
Tim Stallard
Archie Pusaka
Linus Torvalds
Miao-chen Chou
Sathish Narsimman
Luiz Augusto von Dentz