dt-bindings: consolidate USB PHYs in bindings/phy

Move USB PHY bindings under usb directory to phy directory which already
contains other USB PHY bindings.

The Samsung USB PHY binding is obsolete and can be removed.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>

4 files changed, 189 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt b/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt
new file mode 100644
index 000000000000..f37b3a86341d
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt
@@ -0,0 +1,20 @@
+TI Keystone USB PHY
+
+Required properties:
+ - compatible: should be "ti,keystone-usbphy".
+ - #address-cells, #size-cells : should be '1' if the device has sub-nodes
+   with 'reg' property.
+ - reg : Address and length of the usb phy control register set.
+
+The main purpose of this PHY driver is to enable the USB PHY reference clock
+gate on the Keystone SOC for both the USB2 and USB3 PHY. Otherwise it is just
+an NOP PHY driver.  Hence this node is referenced as both the usb2 and usb3
+phy node in the USB Glue layer driver node.
+
+usb_phy: usb_phy@2620738 {
+	compatible = "ti,keystone-usbphy";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	reg = <0x2620738 32>;
+	status = "disabled";
+};
diff --git a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt
new file mode 100644
index 000000000000..379b84a567cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt
@@ -0,0 +1,21 @@
+* Freescale MXS USB Phy Device
+
+Required properties:
+- compatible: should contain:
+	* "fsl,imx23-usbphy" for imx23 and imx28
+	* "fsl,imx6q-usbphy" for imx6dq and imx6dl
+	* "fsl,imx6sl-usbphy" for imx6sl
+	* "fsl,vf610-usbphy" for Vybrid vf610
+	* "fsl,imx6sx-usbphy" for imx6sx
+  "fsl,imx23-usbphy" is still a fallback for other strings
+- reg: Should contain registers location and length
+- interrupts: Should contain phy interrupt
+- fsl,anatop: phandle for anatop register, it is only for imx6 SoC series
+
+Example:
+usbphy1: usbphy@020c9000 {
+	compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy";
+	reg = <0x020c9000 0x1000>;
+	interrupts = <0 44 0x04>;
+	fsl,anatop = <&anatop>;
+};
diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt
new file mode 100644
index 000000000000..a9aa79fb90ed
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt
@@ -0,0 +1,72 @@
+Tegra SOC USB PHY
+
+The device node for Tegra SOC USB PHY:
+
+Required properties :
+ - compatible : For Tegra20, must contain "nvidia,tegra20-usb-phy".
+   For Tegra30, must contain "nvidia,tegra30-usb-phy".  Otherwise, must contain
+   "nvidia,<chip>-usb-phy" plus at least one of the above, where <chip> is
+   tegra114, tegra124, tegra132, or tegra210.
+ - reg : Defines the following set of registers, in the order listed:
+   - The PHY's own register set.
+     Always present.
+   - The register set of the PHY containing the UTMI pad control registers.
+     Present if-and-only-if phy_type == utmi.
+ - phy_type : Should be one of "utmi", "ulpi" or "hsic".
+ - clocks : Defines the clocks listed in the clock-names property.
+ - clock-names : The following clock names must be present:
+   - reg: The clock needed to access the PHY's own registers. This is the
+     associated EHCI controller's clock. Always present.
+   - pll_u: PLL_U. Always present.
+   - timer: The timeout clock (clk_m). Present if phy_type == utmi.
+   - utmi-pads: The clock needed to access the UTMI pad control registers.
+     Present if phy_type == utmi.
+   - ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2).
+     Present if phy_type == ulpi, and ULPI link mode is in use.
+ - resets : Must contain an entry for each entry in reset-names.
+   See ../reset/reset.txt for details.
+ - reset-names : Must include the following entries:
+   - usb: The PHY's own reset signal.
+   - utmi-pads: The reset of the PHY containing the chip-wide UTMI pad control
+     registers. Required even if phy_type == ulpi.
+
+Required properties for phy_type == ulpi:
+  - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
+
+Required PHY timing params for utmi phy, for all chips:
+  - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before
+    start of sync launches RxActive
+  - nvidia,elastic-limit : Variable FIFO Depth of elastic input store
+  - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait
+    before declare IDLE.
+  - nvidia,term-range-adj : Range adjusment on terminations
+  - Either one of the following for HS driver output control:
+    - nvidia,xcvr-setup : integer, uses the provided value.
+    - nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read
+      from the on-chip fuses
+    If both are provided, nvidia,xcvr-setup-use-fuses takes precedence.
+  - nvidia,xcvr-lsfslew : LS falling slew rate control.
+  - nvidia,xcvr-lsrslew :  LS rising slew rate control.
+
+Required PHY timing params for utmi phy, only on Tegra30 and above:
+  - nvidia,xcvr-hsslew : HS slew rate control.
+  - nvidia,hssquelch-level : HS squelch detector level.
+  - nvidia,hsdiscon-level : HS disconnect detector level.
+
+Optional properties:
+  - nvidia,has-legacy-mode : boolean indicates whether this controller can
+    operate in legacy mode (as APX 2500 / 2600). In legacy mode some
+    registers are accessed through the APB_MISC base address instead of
+    the USB controller.
+  - nvidia,is-wired : boolean. Indicates whether we can do certain kind of power
+    optimizations for the devices that are always connected. e.g. modem.
+  - dr_mode : dual role mode. Indicates the working mode for the PHY. Can be
+    "host", "peripheral", or "otg". Defaults to "host" if not defined.
+      host means this is a host controller
+      peripheral means it is device controller
+      otg means it can operate as either ("on the go")
+  - nvidia,has-utmi-pad-registers : boolean indicates whether this controller
+    contains the UTMI pad control registers common to all USB controllers.
+
+VBUS control (required for dr_mode == otg, optional for dr_mode == host):
+  - vbus-supply: regulator for VBUS
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt
new file mode 100644
index 000000000000..2cb2168cef41
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt
@@ -0,0 +1,76 @@
+Qualcomm's APQ8016/MSM8916 USB transceiver controller
+
+- compatible:
+    Usage: required
+    Value type: <string>
+    Definition: Should contain "qcom,usb-8x16-phy".
+
+- reg:
+    Usage: required
+    Value type: <prop-encoded-array>
+    Definition: USB PHY base address and length of the register map
+
+- clocks:
+    Usage: required
+    Value type: <prop-encoded-array>
+    Definition: See clock-bindings.txt section "consumers". List of
+                two clock specifiers for interface and core controller
+                clocks.
+
+- clock-names:
+    Usage: required
+    Value type: <string>
+    Definition: Must contain "iface" and "core" strings.
+
+- vddcx-supply:
+    Usage: required
+    Value type: <phandle>
+    Definition: phandle to the regulator VDCCX supply node.
+
+- v1p8-supply:
+    Usage: required
+    Value type: <phandle>
+    Definition: phandle to the regulator 1.8V supply node.
+
+- v3p3-supply:
+    Usage: required
+    Value type: <phandle>
+    Definition: phandle to the regulator 3.3V supply node.
+
+- resets:
+    Usage: required
+    Value type: <prop-encoded-array>
+    Definition: See reset.txt section "consumers". PHY reset specifier.
+
+- reset-names:
+    Usage: required
+    Value type: <string>
+    Definition: Must contain "phy" string.
+
+- switch-gpio:
+    Usage: optional
+    Value type: <prop-encoded-array>
+    Definition: Some boards are using Dual SPDT USB Switch, witch is
+                controlled by GPIO to de/multiplex D+/D- USB lines
+                between connectors.
+
+Example:
+	usb_phy: phy@78d9000 {
+		compatible = "qcom,usb-8x16-phy";
+		reg = <0x78d9000 0x400>;
+
+		vddcx-supply = <&pm8916_s1_corner>;
+		v1p8-supply = <&pm8916_l7>;
+		v3p3-supply = <&pm8916_l13>;
+
+		clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+			     <&gcc GCC_USB_HS_SYSTEM_CLK>;
+		clock-names = "iface", "core";
+
+		resets = <&gcc GCC_USB2A_PHY_BCR>;
+		reset-names = "phy";
+
+		// D+/D- lines: 1 - Routed to HUB, 0 - Device connector
+		switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>;
+	};
+