1 files changed, 0 insertions, 148 deletions
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt
deleted file mode 100644
index 7b124242b0c5..000000000000
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt
+++ /dev/null
@@ -1,148 +0,0 @@
-Mediatek HDMI Encoder
-=====================
-
-The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from
-its parallel input.
-
-Required properties:
-- compatible: Should be "mediatek,<chip>-hdmi".
-- reg: Physical base address and length of the controller's registers
-- interrupts: The interrupt signal from the function block.
-- clocks: device clocks
-  See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
-- clock-names: must contain "pixel", "pll", "bclk", and "spdif".
-- phys: phandle link to the HDMI PHY node.
-  See Documentation/devicetree/bindings/phy/phy-bindings.txt for details.
-- phy-names: must contain "hdmi"
-- mediatek,syscon-hdmi: phandle link and register offset to the system
-  configuration registers. For mt8173 this must be offset 0x900 into the
-  MMSYS_CONFIG region: <&mmsys 0x900>.
-- ports: A node containing input and output port nodes with endpoint
-  definitions as documented in Documentation/devicetree/bindings/graph.txt.
-- port@0: The input port in the ports node should be connected to a DPI output
-  port.
-- port@1: The output port in the ports node should be connected to the input
-  port of a connector node that contains a ddc-i2c-bus property, or to the
-  input port of an attached bridge chip, such as a SlimPort transmitter.
-
-HDMI CEC
-========
-
-The HDMI CEC controller handles hotplug detection and CEC communication.
-
-Required properties:
-- compatible: Should be "mediatek,<chip>-cec"
-- reg: Physical base address and length of the controller's registers
-- interrupts: The interrupt signal from the function block.
-- clocks: device clock
-
-HDMI DDC
-========
-
-The HDMI DDC i2c controller is used to interface with the HDMI DDC pins.
-The Mediatek's I2C controller is used to interface with I2C devices.
-
-Required properties:
-- compatible: Should be "mediatek,<chip>-hdmi-ddc"
-- reg: Physical base address and length of the controller's registers
-- clocks: device clock
-- clock-names: Should be "ddc-i2c".
-
-HDMI PHY
-========
-
-The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel
-output and drives the HDMI pads.
-
-Required properties:
-- compatible: "mediatek,<chip>-hdmi-phy"
-- reg: Physical base address and length of the module's registers
-- clocks: PLL reference clock
-- clock-names: must contain "pll_ref"
-- clock-output-names: must be "hdmitx_dig_cts" on mt8173
-- #phy-cells: must be <0>
-- #clock-cells: must be <0>
-
-Optional properties:
-- mediatek,ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa
-- mediatek,ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c
-
-Example:
-
-cec: cec@10013000 {
-	compatible = "mediatek,mt8173-cec";
-	reg = <0 0x10013000 0 0xbc>;
-	interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&infracfg CLK_INFRA_CEC>;
-};
-
-hdmi_phy: hdmi-phy@10209100 {
-	compatible = "mediatek,mt8173-hdmi-phy";
-	reg = <0 0x10209100 0 0x24>;
-	clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
-	clock-names = "pll_ref";
-	clock-output-names = "hdmitx_dig_cts";
-	mediatek,ibias = <0xa>;
-	mediatek,ibias_up = <0x1c>;
-	#clock-cells = <0>;
-	#phy-cells = <0>;
-};
-
-hdmi_ddc0: i2c@11012000 {
-	compatible = "mediatek,mt8173-hdmi-ddc";
-	reg = <0 0x11012000 0 0x1c>;
-	interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&pericfg CLK_PERI_I2C5>;
-	clock-names = "ddc-i2c";
-};
-
-hdmi0: hdmi@14025000 {
-	compatible = "mediatek,mt8173-hdmi";
-	reg = <0 0x14025000 0 0x400>;
-	interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
-		 <&mmsys CLK_MM_HDMI_PLLCK>,
-		 <&mmsys CLK_MM_HDMI_AUDIO>,
-		 <&mmsys CLK_MM_HDMI_SPDIF>;
-	clock-names = "pixel", "pll", "bclk", "spdif";
-	pinctrl-names = "default";
-	pinctrl-0 = <&hdmi_pin>;
-	phys = <&hdmi_phy>;
-	phy-names = "hdmi";
-	mediatek,syscon-hdmi = <&mmsys 0x900>;
-	assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>;
-	assigned-clock-parents = <&hdmi_phy>;
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-
-			hdmi0_in: endpoint {
-				remote-endpoint = <&dpi0_out>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			hdmi0_out: endpoint {
-				remote-endpoint = <&hdmi_con_in>;
-			};
-		};
-	};
-};
-
-connector {
-	compatible = "hdmi-connector";
-	type = "a";
-	ddc-i2c-bus = <&hdmiddc0>;
-
-	port {
-		hdmi_con_in: endpoint {
-			remote-endpoint = <&hdmi0_out>;
-		};
-	};
-};