diff options
Diffstat (limited to 'Documentation/devicetree/bindings/eeprom')
| -rw-r--r-- | Documentation/devicetree/bindings/eeprom/at24.txt | 78 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/eeprom/at25.txt | 17 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/eeprom/eeprom.txt | 45 |
3 files changed, 90 insertions, 50 deletions
diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt new file mode 100644 index 000000000000..abfae1beca2b --- /dev/null +++ b/Documentation/devicetree/bindings/eeprom/at24.txt @@ -0,0 +1,78 @@ +EEPROMs (I2C) + +Required properties: + + - compatible: Must be a "<manufacturer>,<model>" pair. The following <model> + values are supported (assuming "atmel" as manufacturer): + + "atmel,24c00", + "atmel,24c01", + "atmel,24cs01", + "atmel,24c02", + "atmel,24cs02", + "atmel,24mac402", + "atmel,24mac602", + "atmel,spd", + "atmel,24c04", + "atmel,24cs04", + "atmel,24c08", + "atmel,24cs08", + "atmel,24c16", + "atmel,24cs16", + "atmel,24c32", + "atmel,24cs32", + "atmel,24c64", + "atmel,24cs64", + "atmel,24c128", + "atmel,24c256", + "atmel,24c512", + "atmel,24c1024", + + If <manufacturer> is not "atmel", then a fallback must be used + with the same <model> and "atmel" as manufacturer. + + Example: + compatible = "microchip,24c128", "atmel,24c128"; + + Supported manufacturers are: + + "catalyst", + "microchip", + "nxp", + "ramtron", + "renesas", + "st", + + Some vendors use different model names for chips which are just + variants of the above. Known such exceptions are listed below: + + "renesas,r1ex24002" - the fallback is "atmel,24c02" + + - reg: The I2C address of the EEPROM. + +Optional properties: + + - pagesize: The length of the pagesize for writing. Please consult the + manual of your device, that value varies a lot. A wrong value + may result in data loss! If not specified, a safety value of + '1' is used which will be very slow. + + - read-only: This parameterless property disables writes to the eeprom. + + - size: Total eeprom size in bytes. + + - no-read-rollover: This parameterless property indicates that the + multi-address eeprom does not automatically roll over + reads to the next slave address. Please consult the + manual of your device. + + - wp-gpios: GPIO to which the write-protect pin of the chip is connected. + +Example: + +eeprom@52 { + compatible = "atmel,24c32"; + reg = <0x52>; + pagesize = <32>; + wp-gpios = <&gpio1 3 0>; +}; diff --git a/Documentation/devicetree/bindings/eeprom/at25.txt b/Documentation/devicetree/bindings/eeprom/at25.txt index 1d3447165c37..b3bde97dc199 100644 --- a/Documentation/devicetree/bindings/eeprom/at25.txt +++ b/Documentation/devicetree/bindings/eeprom/at25.txt @@ -1,19 +1,26 @@ EEPROMs (SPI) compatible with Atmel at25. Required properties: -- compatible : "atmel,at25". +- compatible : Should be "<vendor>,<type>", and generic value "atmel,at25". + Example "<vendor>,<type>" values: + "microchip,25lc040" + "st,m95m02" + "st,m95256" + - reg : chip select number - spi-max-frequency : max spi frequency to use - pagesize : size of the eeprom page - size : total eeprom size in bytes -- address-width : number of address bits (one of 8, 16, or 24) +- address-width : number of address bits (one of 8, 9, 16, or 24). + For 9 bits, the MSB of the address is sent as bit 3 of the instruction + byte, before the address byte. Optional properties: - spi-cpha : SPI shifted clock phase, as per spi-bus bindings. - spi-cpol : SPI inverse clock polarity, as per spi-bus bindings. - read-only : this parameter-less property disables writes to the eeprom -Obsolete legacy properties are can be used in place of "size", "pagesize", +Obsolete legacy properties can be used in place of "size", "pagesize", "address-width", and "read-only": - at25,byte-len : total eeprom size in bytes - at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h @@ -22,8 +29,8 @@ Obsolete legacy properties are can be used in place of "size", "pagesize", Additional compatible properties are also allowed. Example: - at25@0 { - compatible = "atmel,at25", "st,m95256"; + eeprom@0 { + compatible = "st,m95256", "atmel,at25"; reg = <0> spi-max-frequency = <5000000>; spi-cpha; diff --git a/Documentation/devicetree/bindings/eeprom/eeprom.txt b/Documentation/devicetree/bindings/eeprom/eeprom.txt deleted file mode 100644 index afc04589eadf..000000000000 --- a/Documentation/devicetree/bindings/eeprom/eeprom.txt +++ /dev/null @@ -1,45 +0,0 @@ -EEPROMs (I2C) - -Required properties: - - - compatible : should be "<manufacturer>,<type>", like these: - - "atmel,24c00", "atmel,24c01", "atmel,24c02", "atmel,24c04", - "atmel,24c08", "atmel,24c16", "atmel,24c32", "atmel,24c64", - "atmel,24c128", "atmel,24c256", "atmel,24c512", "atmel,24c1024" - - "catalyst,24c32" - - "microchip,24c128" - - "ramtron,24c64" - - "renesas,r1ex24002" - - The following manufacturers values have been deprecated: - "at", "at24" - - If there is no specific driver for <manufacturer>, a generic - device with <type> and manufacturer "atmel" should be used. - Possible types are: - "24c00", "24c01", "24c02", "24c04", "24c08", "24c16", "24c32", "24c64", - "24c128", "24c256", "24c512", "24c1024", "spd" - - - reg : the I2C address of the EEPROM - -Optional properties: - - - pagesize : the length of the pagesize for writing. Please consult the - manual of your device, that value varies a lot. A wrong value - may result in data loss! If not specified, a safety value of - '1' is used which will be very slow. - - - read-only: this parameterless property disables writes to the eeprom - -Example: - -eeprom@52 { - compatible = "atmel,24c32"; - reg = <0x52>; - pagesize = <32>; -}; |