diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media/i2c')
7 files changed, 138 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/imx274.txt b/Documentation/devicetree/bindings/media/i2c/imx274.txt new file mode 100644 index 000000000000..80f2e89568e1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/imx274.txt @@ -0,0 +1,33 @@ +* Sony 1/2.5-Inch 8.51Mp CMOS Digital Image Sensor + +The Sony imx274 is a 1/2.5-inch CMOS active pixel digital image sensor with +an active array size of 3864H x 2202V. It is programmable through I2C +interface. The I2C address is fixed to 0x1a as per sensor data sheet. +Image data is sent through MIPI CSI-2, which is configured as 4 lanes +at 1440 Mbps. + + +Required Properties: +- compatible: value should be "sony,imx274" for imx274 sensor +- reg: I2C bus address of the device + +Optional Properties: +- reset-gpios: Sensor reset GPIO + +The imx274 device node should contain one 'port' child node with +an 'endpoint' subnode. For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + sensor@1a { + compatible = "sony,imx274"; + reg = <0x1a>; + #address-cells = <1>; + #size-cells = <0>; + reset-gpios = <&gpio_sensor 0 0>; + port { + sensor_out: endpoint { + remote-endpoint = <&csiss_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt index ed5a334b1e57..6b910036b57e 100644 --- a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt +++ b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt @@ -6,6 +6,8 @@ interface. Required Properties: - compatible: value should be "micron,mt9m111" +- clocks: reference to the master clock. +- clock-names: shall be "mclk". For further reading on port node refer to Documentation/devicetree/bindings/media/video-interfaces.txt. @@ -16,6 +18,8 @@ Example: mt9m111@5d { compatible = "micron,mt9m111"; reg = <0x5d>; + clocks = <&mclk>; + clock-names = "mclk"; remote = <&pxa_camera>; port { diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt index 855e1faf73e2..33f10a94c381 100644 --- a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt +++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt @@ -27,6 +27,8 @@ Optional properties - nokia,nvm-size: The size of the NVM, in bytes. If the size is not given, the NVM contents will not be read. - reset-gpios: XSHUTDOWN GPIO +- flash-leds: See ../video-interfaces.txt +- lens-focus: See ../video-interfaces.txt Endpoint node mandatory properties diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt index 540b36c4b1f2..8e36da0d8406 100644 --- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt @@ -1,4 +1,4 @@ -* Omnivision OV5640 MIPI CSI-2 sensor +* Omnivision OV5640 MIPI CSI-2 / parallel sensor Required Properties: - compatible: should be "ovti,ov5640" @@ -18,7 +18,25 @@ The device node must contain one 'port' child node for its digital output video port, in accordance with the video interface bindings defined in Documentation/devicetree/bindings/media/video-interfaces.txt. -Example: +OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint. + +Endpoint node required properties for CSI-2 connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- clock-lanes: should be set to <0> (clock lane on hardware lane 0) +- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported) + +Endpoint node required properties for parallel connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- bus-width: shall be set to <8> for 8 bits parallel bus + or <10> for 10 bits parallel bus +- data-shift: shall be set to <2> for 8 bits parallel bus + (lines 9:2 are used) or <0> for 10 bits parallel bus +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. +- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock + signal. + +Examples: &i2c1 { ov5640: camera@3c { @@ -35,6 +53,7 @@ Example: reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; port { + /* MIPI CSI-2 bus endpoint */ ov5640_to_mipi_csi2: endpoint { remote-endpoint = <&mipi_csi2_from_ov5640>; clock-lanes = <0>; @@ -43,3 +62,26 @@ Example: }; }; }; + +&i2c1 { + ov5640: camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + clock-names = "xclk"; + + port { + /* Parallel bus endpoint */ + ov5640_to_parallel: endpoint { + remote-endpoint = <¶llel_from_ov5640>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov7740.txt b/Documentation/devicetree/bindings/media/i2c/ov7740.txt new file mode 100644 index 000000000000..af781c3a5f0e --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov7740.txt @@ -0,0 +1,47 @@ +* Omnivision OV7740 CMOS image sensor + +The Omnivision OV7740 image sensor supports multiple output image +size, such as VGA, and QVGA, CIF and any size smaller. It also +supports the RAW RGB and YUV output formats. + +The common video interfaces bindings (see video-interfaces.txt) should +be used to specify link to the image data receiver. The OV7740 device +node should contain one 'port' child node with an 'endpoint' subnode. + +Required Properties: +- compatible: "ovti,ov7740". +- reg: I2C slave address of the sensor. +- clocks: Reference to the xvclk input clock. +- clock-names: "xvclk". + +Optional Properties: +- reset-gpios: Rreference to the GPIO connected to the reset_b pin, + if any. Active low with pull-ip resistor. +- powerdown-gpios: Reference to the GPIO connected to the pwdn pin, + if any. Active high with pull-down resistor. + +Endpoint node mandatory properties: +- remote-endpoint: A phandle to the bus receiver's endpoint node. + +Example: + + i2c1: i2c@fc028000 { + ov7740: camera@21 { + compatible = "ovti,ov7740"; + reg = <0x21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>; + clocks = <&isc>; + clock-names = "xvclk"; + assigned-clocks = <&isc>; + assigned-clock-rates = <24000000>; + reset-gpios = <&pioA 43 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&pioA 44 GPIO_ACTIVE_HIGH>; + + port { + ov7740_0: endpoint { + remote-endpoint = <&isc_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/tc358743.txt b/Documentation/devicetree/bindings/media/i2c/tc358743.txt index 5218921629ed..49f8bcc2ea4d 100644 --- a/Documentation/devicetree/bindings/media/i2c/tc358743.txt +++ b/Documentation/devicetree/bindings/media/i2c/tc358743.txt @@ -27,7 +27,7 @@ Documentation/devicetree/bindings/media/video-interfaces.txt. Example: - tc358743@0f { + tc358743@f { compatible = "toshiba,tc358743"; reg = <0x0f>; clocks = <&hdmi_osc>; diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt index 0b7b6a4d84ff..e80d5891b7ed 100644 --- a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt @@ -20,6 +20,13 @@ Mandatory properties is in hardware standby mode when the signal is in the low state. +Optional properties +------------------- + +- flash-leds: See ../video-interfaces.txt +- lens-focus: See ../video-interfaces.txt + + Endpoint node mandatory properties ---------------------------------- |