diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc')
12 files changed, 175 insertions, 15 deletions
diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdio.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdio.txt new file mode 100644 index 000000000000..8765c605e6bc --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-mx-sdio.txt @@ -0,0 +1,54 @@ +* Amlogic Meson6, Meson8 and Meson8b SDIO/MMC controller + +The highspeed MMC host controller on Amlogic SoCs provides an interface +for MMC, SD, SDIO and SDHC types of memory cards. + +Supported maximum speeds are the ones of the eMMC standard 4.41 as well +as the speed of SD standard 2.0. + +The hardware provides an internal "mux" which allows up to three slots +to be controlled. Only one slot can be accessed at a time. + +Required properties: + - compatible : must be one of + - "amlogic,meson8-sdio" + - "amlogic,meson8b-sdio" + along with the generic "amlogic,meson-mx-sdio" + - reg : mmc controller base registers + - interrupts : mmc controller interrupt + - #address-cells : must be 1 + - size-cells : must be 0 + - clocks : phandle to clock providers + - clock-names : must contain "core" and "clkin" + +Required child nodes: +A node for each slot provided by the MMC controller is required. +NOTE: due to a driver limitation currently only one slot (= child node) + is supported! + +Required properties on each child node (= slot): + - compatible : must be "mmc-slot" (see mmc.txt within this directory) + - reg : the slot (or "port") ID + +Optional properties on each child node (= slot): + - bus-width : must be 1 or 4 (8-bit bus is not supported) + - for cd and all other additional generic mmc parameters + please refer to mmc.txt within this directory + +Examples: + mmc@c1108c20 { + compatible = "amlogic,meson8-sdio", "amlogic,meson-mx-sdio"; + reg = <0xc1108c20 0x20>; + interrupts = <0 28 1>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clkc CLKID_SDIO>, <&clkc CLKID_CLK81>; + clock-names = "core", "clkin"; + + slot@1 { + compatible = "mmc-slot"; + reg = <1>; + + bus-width = <4>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt index aaba2483b4ff..7f5dd83f5bd9 100644 --- a/Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt @@ -12,7 +12,7 @@ Refer to clocks/clock-bindings.txt for generic clock consumer properties. Example: -sdio2: sdio@0x3f1a0000 { +sdio2: sdio@3f1a0000 { compatible = "brcm,kona-sdhci"; reg = <0x3f1a0000 0x10000>; clocks = <&sdio3_clk>; diff --git a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt index 954561d09a8e..fa90d253dc7e 100644 --- a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt +++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt @@ -24,7 +24,7 @@ Optional properties: Example: -sdhci0: sdhci@0x18041000 { +sdhci0: sdhci@18041000 { compatible = "brcm,sdhci-iproc-cygnus"; reg = <0x18041000 0x100>; interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index b32ade645ad9..467cd7b147ce 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -53,6 +53,9 @@ Optional properties: - no-sdio: controller is limited to send sdio cmd during initialization - no-sd: controller is limited to send sd cmd during initialization - no-mmc: controller is limited to send mmc cmd during initialization +- fixed-emmc-driver-type: for non-removable eMMC, enforce this driver type. + The value <n> is the driver type as specified in the eMMC specification + (table 206 in spec version 5.1). *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" @@ -64,10 +67,10 @@ logic applies to the "wp-inverted" property. CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs, specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of dedicated pins can be specified, using *-inverted properties. GPIO polarity can -also be specified using the OF_GPIO_ACTIVE_LOW flag. This creates an ambiguity +also be specified using the GPIO_ACTIVE_LOW flag. This creates an ambiguity in the latter case. We choose to use the XOR logic for GPIO CD and WP lines. This means, the two properties are "superimposed," for example leaving the -OF_GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted +GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted property property results in a double-inversion and actually means the "normal" line polarity is in effect. @@ -143,7 +146,7 @@ sdhci@ab000000 { Example with sdio function subnode: -mmc3: mmc@01c12000 { +mmc3: mmc@1c12000 { #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt index 4182ea36ca5b..9b8017670870 100644 --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt @@ -7,10 +7,20 @@ This file documents differences between the core properties in mmc.txt and the properties used by the msdc driver. Required properties: -- compatible: Should be "mediatek,mt8173-mmc","mediatek,mt8135-mmc" +- compatible: value should be either of the following. + "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135 + "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173 + "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701 + "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712 + "mediatek,mt7623-mmc", "mediatek,mt2701-mmc": for MT7623 SoC + +- reg: physical base address of the controller and length - interrupts: Should contain MSDC interrupt number -- clocks: MSDC source clock, HCLK -- clock-names: "source", "hclk" +- clocks: Should contain phandle for the clock feeding the MMC controller +- clock-names: Should contain the following: + "source" - source clock (required) + "hclk" - HCLK which used for host (required) + "source_cg" - independent source clock gate (required for MT2712) - pinctrl-names: should be "default", "state_uhs" - pinctrl-0: should contain default/high speed pin ctrl - pinctrl-1: should contain uhs mode pin ctrl @@ -30,6 +40,10 @@ Optional properties: - mediatek,hs400-cmd-resp-sel-rising: HS400 command response sample selection If present,HS400 command responses are sampled on rising edges. If not present,HS400 command responses are sampled on falling edges. +- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc + error caused by stop clock(fifo full) + Valid range = [0:0x7]. if not present, default value is 0. + applied to compatible "mediatek,mt2701-mmc". Examples: mmc0: mmc@11230000 { diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt index de2c53cff4f1..3ee9263adf73 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt @@ -15,6 +15,8 @@ Required properties: Optional properties: - vqmmc-supply: phandle to the regulator device tree node, mentioned as the VCCQ/VDD_IO supply in the eMMC/SD specs. +- fujitsu,cmd-dat-delay-select: boolean property indicating that this host + requires the CMD_DAT_DELAY control to be enabled. Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt index 0576264eab5e..bfdcdc4ccdff 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt @@ -18,6 +18,8 @@ Required properties: "core" - SDC MMC clock (MCLK) (required) "bus" - SDCC bus voter clock (optional) "xo" - TCXO clock (optional) + "cal" - reference clock for RCLK delay calibration (optional) + "sleep" - sleep clock for RCLK delay calibration (optional) Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt new file mode 100644 index 000000000000..51775a372c06 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt @@ -0,0 +1,16 @@ +* TI OMAP SDHCI Controller + +Refer to mmc.txt for standard MMC bindings. + +Required properties: +- compatible: Should be "ti,dra7-sdhci" for DRA7 and DRA72 controllers +- ti,hwmods: Must be "mmc<n>", <n> is controller instance starting 1 + +Example: + mmc1: mmc@4809c000 { + compatible = "ti,dra7-sdhci"; + reg = <0x4809c000 0x400>; + ti,hwmods = "mmc1"; + bus-width = <4>; + vmmc-supply = <&vmmc>; /* phandle to regulator node */ + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index e35645598315..6b3d40ca395e 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -74,7 +74,7 @@ mmc0: sdhci@fe81e000 { /* Example SD stih407 family configuration */ -mmc1: sdhci@09080000 { +mmc1: sdhci@9080000 { compatible = "st,sdhci-stih407", "st,sdhci"; reg = <0x09080000 0x7ff>; reg-names = "mmc"; @@ -90,7 +90,7 @@ mmc1: sdhci@09080000 { /* Example eMMC stih407 family configuration */ -mmc0: sdhci@09060000 { +mmc0: sdhci@9060000 { compatible = "st,sdhci-stih407", "st,sdhci"; reg = <0x09060000 0x7ff>, <0x9061008 0x20>; reg-names = "mmc", "top-mmc-delay"; diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt index 63b57e2a10fb..132e0007d7d6 100644 --- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt @@ -29,7 +29,7 @@ Optional properties: Examples: - Within .dtsi: - mmc0: mmc@01c0f000 { + mmc0: mmc@1c0f000 { compatible = "allwinner,sun5i-a13-mmc"; reg = <0x01c0f000 0x1000>; clocks = <&ahb_gates 8>, <&mmc0_clk>, <&mmc0_output_clk>, <&mmc0_sample_clk>; @@ -39,7 +39,7 @@ Examples: }; - Within dts: - mmc0: mmc@01c0f000 { + mmc0: mmc@1c0f000 { pinctrl-names = "default", "default"; pinctrl-0 = <&mmc0_pins_a>; pinctrl-1 = <&mmc0_cd_pin_reference_design>; diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index 3a4ac401e6f9..19f5508a7569 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -55,7 +55,7 @@ Examples: [hwmod populated DMA resources] - mmc1: mmc@0x4809c000 { + mmc1: mmc@4809c000 { compatible = "ti,omap4-hsmmc"; reg = <0x4809c000 0x400>; ti,hwmods = "mmc1"; @@ -67,7 +67,7 @@ Examples: [generic DMA request binding] - mmc1: mmc@0x4809c000 { + mmc1: mmc@4809c000 { compatible = "ti,omap4-hsmmc"; reg = <0x4809c000 0x400>; ti,hwmods = "mmc1"; diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 54ef642f23a0..d8685cb83325 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -10,7 +10,7 @@ described in mmc.txt, can be used. Additionally the following tmio_mmc-specific optional bindings can be used. Required properties: -- compatible: "renesas,sdhi-shmobile" - a generic sh-mobile SDHI unit +- compatible: should contain one or more of the following: "renesas,sdhi-sh73a0" - SDHI IP on SH73A0 SoC "renesas,sdhi-r7s72100" - SDHI IP on R7S72100 SoC "renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC @@ -26,6 +26,17 @@ Required properties: "renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC + "renesas,sdhi-r8a77995" - SDHI IP on R8A77995 SoC + "renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller + "renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller + "renesas,rcar-gen2-sdhi" - a generic R-Car Gen2 or RZ/G1 + SDHI controller + "renesas,rcar-gen3-sdhi" - a generic R-Car Gen3 SDHI controller + + + When compatible with the generic version, nodes must list + the SoC-specific version corresponding to the platform + first followed by the generic version. - clocks: Most controllers only have 1 clock source per channel. However, on some variations of this controller, the internal card detection @@ -43,3 +54,61 @@ Optional properties: - pinctrl-names: should be "default", "state_uhs" - pinctrl-0: should contain default/high speed pin ctrl - pinctrl-1: should contain uhs mode pin ctrl + +Example: R8A7790 (R-Car H2) SDHI controller nodes + + sdhi0: sd@ee100000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0 0xee100000 0 0x328>; + interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 314>; + dmas = <&dmac0 0xcd>, <&dmac0 0xce>, + <&dmac1 0xcd>, <&dmac1 0xce>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <195000000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 314>; + status = "disabled"; + }; + + sdhi1: sd@ee120000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0 0xee120000 0 0x328>; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 313>; + dmas = <&dmac0 0xc9>, <&dmac0 0xca>, + <&dmac1 0xc9>, <&dmac1 0xca>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <195000000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 313>; + status = "disabled"; + }; + + sdhi2: sd@ee140000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0 0xee140000 0 0x100>; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 312>; + dmas = <&dmac0 0xc1>, <&dmac0 0xc2>, + <&dmac1 0xc1>, <&dmac1 0xc2>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <97500000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 312>; + status = "disabled"; + }; + + sdhi3: sd@ee160000 { + compatible = "renesas,sdhi-r8a7790", "renesas,rcar-gen2-sdhi"; + reg = <0 0xee160000 0 0x100>; + interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 311>; + dmas = <&dmac0 0xd3>, <&dmac0 0xd4>, + <&dmac1 0xd3>, <&dmac1 0xd4>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <97500000>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 311>; + status = "disabled"; + }; |