diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mtd')
35 files changed, 647 insertions, 307 deletions
diff --git a/Documentation/devicetree/bindings/mtd/allwinner,sun4i-a10-nand.yaml b/Documentation/devicetree/bindings/mtd/allwinner,sun4i-a10-nand.yaml index c033ac3f147d..4741864da48e 100644 --- a/Documentation/devicetree/bindings/mtd/allwinner,sun4i-a10-nand.yaml +++ b/Documentation/devicetree/bindings/mtd/allwinner,sun4i-a10-nand.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/mtd/allwinner,sun4i-a10-nand.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Allwinner A10 NAND Controller Device Tree Bindings +title: Allwinner A10 NAND Controller allOf: - $ref: "nand-controller.yaml" diff --git a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt deleted file mode 100644 index 5794ab1147c1..000000000000 --- a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt +++ /dev/null @@ -1,60 +0,0 @@ -Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs - -This file documents the properties in addition to those available in -the MTD NAND bindings. - -Required properties: -- compatible : contains one of: - - "amlogic,meson-gxl-nfc" - - "amlogic,meson-axg-nfc" -- clocks : - A list of phandle + clock-specifier pairs for the clocks listed - in clock-names. - -- clock-names: Should contain the following: - "core" - NFC module gate clock - "device" - device clock from eMMC sub clock controller - "rx" - rx clock phase - "tx" - tx clock phase - -- amlogic,mmc-syscon : Required for NAND clocks, it's shared with SD/eMMC - controller port C - -Optional children nodes: -Children nodes represent the available nand chips. - -Other properties: -see Documentation/devicetree/bindings/mtd/nand-controller.yaml for generic bindings. - -Example demonstrate on AXG SoC: - - sd_emmc_c_clkc: mmc@7000 { - compatible = "amlogic,meson-axg-mmc-clkc", "syscon"; - reg = <0x0 0x7000 0x0 0x800>; - }; - - nand-controller@7800 { - compatible = "amlogic,meson-axg-nfc"; - reg = <0x0 0x7800 0x0 0x100>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>; - - clocks = <&clkc CLKID_SD_EMMC_C>, - <&sd_emmc_c_clkc CLKID_MMC_DIV>, - <&sd_emmc_c_clkc CLKID_MMC_PHASE_RX>, - <&sd_emmc_c_clkc CLKID_MMC_PHASE_TX>; - clock-names = "core", "device", "rx", "tx"; - amlogic,mmc-syscon = <&sd_emmc_c_clkc>; - - pinctrl-names = "default"; - pinctrl-0 = <&nand_pins>; - - nand@0 { - reg = <0>; - #address-cells = <1>; - #size-cells = <1>; - - nand-on-flash-bbt; - }; - }; diff --git a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.yaml b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.yaml new file mode 100644 index 000000000000..28fb9a7dd70f --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/amlogic,meson-nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs + +allOf: + - $ref: nand-controller.yaml + +maintainers: + - liang.yang@amlogic.com + +properties: + compatible: + enum: + - amlogic,meson-gxl-nfc + - amlogic,meson-axg-nfc + + reg: + maxItems: 2 + + reg-names: + items: + - const: nfc + - const: emmc + + interrupts: + maxItems: 1 + + clocks: + minItems: 2 + + clock-names: + items: + - const: core + - const: device + +patternProperties: + "^nand@[0-7]$": + type: object + properties: + reg: + minimum: 0 + maximum: 1 + + nand-ecc-mode: + const: hw + + nand-ecc-step-size: + const: 1024 + + nand-ecc-strength: + enum: [8, 16, 24, 30, 40, 50, 60] + description: | + The ECC configurations that can be supported are as follows. + meson-gxl-nfc 8, 16, 24, 30, 40, 50, 60 + meson-axg-nfc 8 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/axg-clkc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + nand-controller@ffe07800 { + compatible = "amlogic,meson-axg-nfc"; + reg = <0xffe07800 0x100>, <0xffe07000 0x800>; + reg-names = "nfc", "emmc"; + interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc CLKID_SD_EMMC_C>, <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "device"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/arasan,nand-controller.yaml b/Documentation/devicetree/bindings/mtd/arasan,nand-controller.yaml index b32876933269..f013fb976d95 100644 --- a/Documentation/devicetree/bindings/mtd/arasan,nand-controller.yaml +++ b/Documentation/devicetree/bindings/mtd/arasan,nand-controller.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/mtd/arasan,nand-controller.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Arasan NAND Flash Controller with ONFI 3.1 support device tree bindings +title: Arasan NAND Flash Controller with ONFI 3.1 support allOf: - $ref: "nand-controller.yaml" diff --git a/Documentation/devicetree/bindings/mtd/arm,pl353-nand-r2p1.yaml b/Documentation/devicetree/bindings/mtd/arm,pl353-nand-r2p1.yaml index 5f126bb9b202..023f3ef0fa13 100644 --- a/Documentation/devicetree/bindings/mtd/arm,pl353-nand-r2p1.yaml +++ b/Documentation/devicetree/bindings/mtd/arm,pl353-nand-r2p1.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/mtd/arm,pl353-nand-r2p1.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: PL353 NAND Controller device tree bindings +title: PL353 NAND Controller allOf: - $ref: "nand-controller.yaml" diff --git a/Documentation/devicetree/bindings/mtd/aspeed-smc.txt b/Documentation/devicetree/bindings/mtd/aspeed-smc.txt deleted file mode 100644 index 49f6528ef547..000000000000 --- a/Documentation/devicetree/bindings/mtd/aspeed-smc.txt +++ /dev/null @@ -1,51 +0,0 @@ -* Aspeed Firmware Memory controller -* Aspeed SPI Flash Memory Controller - -The Firmware Memory Controller in the Aspeed AST2500 SoC supports -three chip selects, two of which are always of SPI type and the third -can be SPI or NOR type flash. These bindings only describe SPI. - -The two SPI flash memory controllers in the AST2500 each support two -chip selects. - -Required properties: - - compatible : Should be one of - "aspeed,ast2400-fmc" for the AST2400 Firmware Memory Controller - "aspeed,ast2400-spi" for the AST2400 SPI Flash memory Controller - "aspeed,ast2500-fmc" for the AST2500 Firmware Memory Controller - "aspeed,ast2500-spi" for the AST2500 SPI flash memory controllers - - - reg : the first contains the control register location and length, - the second contains the memory window mapping address and length - - #address-cells : must be 1 corresponding to chip select child binding - - #size-cells : must be 0 corresponding to chip select child binding - -Optional properties: - - interrupts : Should contain the interrupt for the dma device if an - FMC - -The child nodes are the SPI flash modules which must have a compatible -property as specified in bindings/mtd/jedec,spi-nor.txt - -Optionally, the child node can contain properties for SPI mode (may be -ignored): - - spi-max-frequency - max frequency of spi bus - - -Example: -fmc: fmc@1e620000 { - compatible = "aspeed,ast2500-fmc"; - reg = < 0x1e620000 0x94 - 0x20000000 0x02000000 >; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <19>; - flash@0 { - reg = < 0 >; - compatible = "jedec,spi-nor"; - /* spi-max-frequency = <>; */ - /* m25p,fast-read; */ - #address-cells = <1>; - #size-cells = <1>; - }; -}; diff --git a/Documentation/devicetree/bindings/mtd/common.txt b/Documentation/devicetree/bindings/mtd/common.txt deleted file mode 100644 index ae16f9ea8606..000000000000 --- a/Documentation/devicetree/bindings/mtd/common.txt +++ /dev/null @@ -1 +0,0 @@ -This file has been moved to mtd.yaml. diff --git a/Documentation/devicetree/bindings/mtd/cortina,gemini-flash.txt b/Documentation/devicetree/bindings/mtd/cortina,gemini-flash.txt deleted file mode 100644 index efa5b2aba829..000000000000 --- a/Documentation/devicetree/bindings/mtd/cortina,gemini-flash.txt +++ /dev/null @@ -1,24 +0,0 @@ -Flash device on Cortina Systems Gemini SoC - -This flash is regular CFI compatible (Intel or AMD extended) flash chips with -some special bits that can be controlled by the machine's system controller. - -Required properties: -- compatible : must be "cortina,gemini-flash", "cfi-flash"; -- reg : memory address for the flash chip -- syscon : must be a phandle to the system controller -- bank-width : width in bytes of flash interface, should be <2> - -For the rest of the properties, see mtd-physmap.yaml. - -The device tree may optionally contain sub-nodes describing partitions of the -address space. See partition.txt for more detail. - -Example: - -flash@30000000 { - compatible = "cortina,gemini-flash", "cfi-flash"; - reg = <0x30000000 0x01000000>; - syscon = <&syscon>; - bank-width = <2>; -}; diff --git a/Documentation/devicetree/bindings/mtd/elm.txt b/Documentation/devicetree/bindings/mtd/elm.txt deleted file mode 100644 index 59ddc61c1076..000000000000 --- a/Documentation/devicetree/bindings/mtd/elm.txt +++ /dev/null @@ -1,16 +0,0 @@ -Error location module - -Required properties: -- compatible: Must be "ti,am3352-elm" -- reg: physical base address and size of the registers map. -- interrupts: Interrupt number for the elm. - -Optional properties: -- ti,hwmods: Name of the hwmod associated to the elm - -Example: -elm: elm@0 { - compatible = "ti,am3352-elm"; - reg = <0x48080000 0x2000>; - interrupts = <4>; -}; diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.yaml b/Documentation/devicetree/bindings/mtd/gpmi-nand.yaml index 9d764e654e1d..849aeae319a9 100644 --- a/Documentation/devicetree/bindings/mtd/gpmi-nand.yaml +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.yaml @@ -147,8 +147,6 @@ allOf: - description: SoC gpmi io clock - description: SoC gpmi bch apb clock clock-names: - minItems: 2 - maxItems: 2 items: - const: gpmi_io - const: gpmi_bch_apb diff --git a/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt b/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt index 74981520d6dd..a99de13c7ccd 100644 --- a/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt +++ b/Documentation/devicetree/bindings/mtd/hisilicon,fmc-spi-nor.txt @@ -17,7 +17,7 @@ spi-nor-controller@10000000 { reg = <0x10000000 0x1000>, <0x14000000 0x1000000>; reg-names = "control", "memory"; clocks = <&clock HI3519_FMC_CLK>; - spi-nor@0 { + flash@0 { compatible = "jedec,spi-nor"; reg = <0>; }; diff --git a/Documentation/devicetree/bindings/mtd/ingenic,nand.yaml b/Documentation/devicetree/bindings/mtd/ingenic,nand.yaml index 9de8ef6e59ca..8c272c842bfd 100644 --- a/Documentation/devicetree/bindings/mtd/ingenic,nand.yaml +++ b/Documentation/devicetree/bindings/mtd/ingenic,nand.yaml @@ -11,6 +11,7 @@ maintainers: allOf: - $ref: nand-controller.yaml# + - $ref: /schemas/memory-controllers/ingenic,nemc-peripherals.yaml# properties: compatible: diff --git a/Documentation/devicetree/bindings/mtd/intel,lgm-nand.yaml b/Documentation/devicetree/bindings/mtd/intel,lgm-ebunand.yaml index 30e0c66ab0eb..741c66ee06c3 100644 --- a/Documentation/devicetree/bindings/mtd/intel,lgm-nand.yaml +++ b/Documentation/devicetree/bindings/mtd/intel,lgm-ebunand.yaml @@ -1,10 +1,10 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: http://devicetree.org/schemas/mtd/intel,lgm-nand.yaml# +$id: http://devicetree.org/schemas/mtd/intel,lgm-ebunand.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Intel LGM SoC NAND Controller Device Tree Bindings +title: Intel LGM SoC NAND Controller allOf: - $ref: "nand-controller.yaml" @@ -14,7 +14,7 @@ maintainers: properties: compatible: - const: intel,lgm-nand + const: intel,lgm-ebunand reg: maxItems: 6 @@ -51,7 +51,7 @@ patternProperties: properties: reg: minimum: 0 - maximum: 7 + maximum: 1 nand-ecc-mode: true @@ -75,7 +75,7 @@ additionalProperties: false examples: - | nand-controller@e0f00000 { - compatible = "intel,lgm-nand"; + compatible = "intel,lgm-ebunand"; reg = <0xe0f00000 0x100>, <0xe1000000 0x300>, <0xe1400000 0x8000>, diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml index 39421f7233e4..7149784a36ac 100644 --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml @@ -47,11 +47,8 @@ properties: identified by the JEDEC READ ID opcode (0x9F). reg: - maxItems: 1 - - spi-max-frequency: true - spi-rx-bus-width: true - spi-tx-bus-width: true + minItems: 1 + maxItems: 2 m25p,fast-read: type: boolean @@ -73,8 +70,6 @@ properties: be used on such systems, to denote the absence of a reliable reset mechanism. - label: true - partitions: type: object @@ -98,8 +93,6 @@ examples: #size-cells = <0>; flash@0 { - #address-cells = <1>; - #size-cells = <1>; compatible = "spansion,m25p80", "jedec,spi-nor"; reg = <0>; spi-max-frequency = <40000000>; diff --git a/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml b/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml index 2cdf6bf3dc4a..8cc2a7ceb5fb 100644 --- a/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml +++ b/Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml @@ -22,13 +22,14 @@ properties: reg: maxItems: 1 - spi-max-frequency: true - required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.yaml b/Documentation/devicetree/bindings/mtd/mtd-physmap.yaml index f827984936f6..82eb4e0f453b 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.yaml +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.yaml @@ -44,7 +44,9 @@ properties: - numonyx,js28f128 - sst,sst39vf320 - xlnx,xps-mch-emc-2.00.a - - const: cfi-flash + - enum: + - cfi-flash + - jedec-flash - items: - enum: - cypress,cy7c1019dv33-10zsxi @@ -127,6 +129,20 @@ required: - compatible - reg +if: + properties: + compatible: + contains: + const: cortina,gemini-flash +then: + properties: + syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the syscon controller + required: + - syscon + # FIXME: A parent bus may define timing properties additionalProperties: true diff --git a/Documentation/devicetree/bindings/mtd/mtd.yaml b/Documentation/devicetree/bindings/mtd/mtd.yaml index 376b679cfc70..3498e485679b 100644 --- a/Documentation/devicetree/bindings/mtd/mtd.yaml +++ b/Documentation/devicetree/bindings/mtd/mtd.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/mtd/mtd.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: MTD (Memory Technology Device) Device Tree Bindings +title: MTD (Memory Technology Device) maintainers: - Miquel Raynal <miquel.raynal@bootlin.com> diff --git a/Documentation/devicetree/bindings/mtd/mxc-nand.yaml b/Documentation/devicetree/bindings/mtd/mxc-nand.yaml index 73b86f2226c7..66da1b476ab7 100644 --- a/Documentation/devicetree/bindings/mtd/mxc-nand.yaml +++ b/Documentation/devicetree/bindings/mtd/mxc-nand.yaml @@ -37,6 +37,4 @@ examples: compatible = "fsl,imx27-nand"; reg = <0xd8000000 0x1000>; interrupts = <29>; - nand-bus-width = <8>; - nand-ecc-mode = "hw"; }; diff --git a/Documentation/devicetree/bindings/mtd/mxicy,nand-ecc-engine.yaml b/Documentation/devicetree/bindings/mtd/mxicy,nand-ecc-engine.yaml new file mode 100644 index 000000000000..f92e7234deab --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mxicy,nand-ecc-engine.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/mxicy,nand-ecc-engine.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Macronix NAND ECC engine + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +properties: + compatible: + const: mxicy,nand-ecc-engine-rev3 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + /* External configuration */ + spi_controller0: spi@43c30000 { + compatible = "mxicy,mx25f0a-spi"; + reg = <0x43c30000 0x10000>, <0xa0000000 0x4000000>; + reg-names = "regs", "dirmap"; + clocks = <&clkwizard 0>, <&clkwizard 1>, <&clkc 15>; + clock-names = "send_clk", "send_dly_clk", "ps_clk"; + #address-cells = <1>; + #size-cells = <0>; + + flash@0 { + compatible = "spi-nand"; + reg = <0>; + nand-ecc-engine = <&ecc_engine0>; + }; + }; + + ecc_engine0: ecc@43c40000 { + compatible = "mxicy,nand-ecc-engine-rev3"; + reg = <0x43c40000 0x10000>; + }; + + - | + /* Pipelined configuration */ + spi_controller1: spi@43c30000 { + compatible = "mxicy,mx25f0a-spi"; + reg = <0x43c30000 0x10000>, <0xa0000000 0x4000000>; + reg-names = "regs", "dirmap"; + clocks = <&clkwizard 0>, <&clkwizard 1>, <&clkc 15>; + clock-names = "send_clk", "send_dly_clk", "ps_clk"; + #address-cells = <1>; + #size-cells = <0>; + nand-ecc-engine = <&ecc_engine1>; + + flash@0 { + compatible = "spi-nand"; + reg = <0>; + nand-ecc-engine = <&spi_controller1>; + }; + }; + + ecc_engine1: ecc@43c40000 { + compatible = "mxicy,nand-ecc-engine-rev3"; + reg = <0x43c40000 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/mtd/nand-chip.yaml b/Documentation/devicetree/bindings/mtd/nand-chip.yaml new file mode 100644 index 000000000000..97ac3a3fbb52 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nand-chip.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/nand-chip.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NAND Chip and NAND Controller Generic Binding + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +description: | + This file covers the generic description of a NAND chip. It implies that the + bus interface should not be taken into account: both raw NAND devices and + SPI-NAND devices are concerned by this description. + +properties: + reg: + description: + Contains the chip-select IDs. + + nand-ecc-engine: + description: | + A phandle on the hardware ECC engine if any. There are + basically three possibilities: + 1/ The ECC engine is part of the NAND controller, in this + case the phandle should reference the parent node. + 2/ The ECC engine is part of the NAND part (on-die), in this + case the phandle should reference the node itself. + 3/ The ECC engine is external, in this case the phandle should + reference the specific ECC engine node. + $ref: /schemas/types.yaml#/definitions/phandle + + nand-use-soft-ecc-engine: + description: Use a software ECC engine. + type: boolean + + nand-no-ecc-engine: + description: Do not use any ECC correction. + type: boolean + + nand-ecc-algo: + description: + Desired ECC algorithm. + $ref: /schemas/types.yaml#/definitions/string + enum: [hamming, bch, rs] + + nand-ecc-strength: + description: + Maximum number of bits that can be corrected per ECC step. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + + nand-ecc-step-size: + description: + Number of data bytes covered by a single ECC step. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + + secure-regions: + description: + Regions in the NAND chip which are protected using a secure element + like Trustzone. This property contains the start address and size of + the secure regions present. + $ref: /schemas/types.yaml#/definitions/uint64-matrix + +required: + - reg + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml index bd217e6f5018..359a015d4e5a 100644 --- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml +++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml @@ -39,8 +39,6 @@ properties: ranges: true cs-gpios: - minItems: 1 - maxItems: 8 description: Array of chip-select available to the controller. The first entries are a 1:1 mapping of the available chip-select on the @@ -48,51 +46,27 @@ properties: chip-select as needed may follow and should be phandles of GPIO lines. 'reg' entries of the NAND chip subnodes become indexes of this array when this property is present. + minItems: 1 + maxItems: 8 patternProperties: "^nand@[a-f0-9]$": type: object + $ref: "nand-chip.yaml#" + properties: reg: description: - Contains the native Ready/Busy IDs. - - nand-ecc-engine: - allOf: - - $ref: /schemas/types.yaml#/definitions/phandle - description: | - A phandle on the hardware ECC engine if any. There are - basically three possibilities: - 1/ The ECC engine is part of the NAND controller, in this - case the phandle should reference the parent node. - 2/ The ECC engine is part of the NAND part (on-die), in this - case the phandle should reference the node itself. - 3/ The ECC engine is external, in this case the phandle should - reference the specific ECC engine node. - - nand-use-soft-ecc-engine: - type: boolean - description: Use a software ECC engine. - - nand-no-ecc-engine: - type: boolean - description: Do not use any ECC correction. + Contains the chip-select IDs. nand-ecc-placement: - allOf: - - $ref: /schemas/types.yaml#/definitions/string - - enum: [ oob, interleaved ] description: Location of the ECC bytes. This location is unknown by default but can be explicitly set to "oob", if all ECC bytes are known to be stored in the OOB area, or "interleaved" if ECC bytes will be interleaved with regular data in the main area. - - nand-ecc-algo: - description: - Desired ECC algorithm. $ref: /schemas/types.yaml#/definitions/string - enum: [hamming, bch, rs] + enum: [ oob, interleaved ] nand-bus-width: description: @@ -102,7 +76,6 @@ patternProperties: default: 8 nand-on-flash-bbt: - $ref: /schemas/types.yaml#/definitions/flag description: With this property, the OS will search the device for a Bad Block Table (BBT). If not found, it will create one, reserve @@ -111,21 +84,9 @@ patternProperties: few pages of all the blocks will be scanned at boot time to find Bad Block Markers (BBM). These markers will help to build a volatile BBT in RAM. - - nand-ecc-strength: - description: - Maximum number of bits that can be corrected per ECC step. - $ref: /schemas/types.yaml#/definitions/uint32 - minimum: 1 - - nand-ecc-step-size: - description: - Number of data bytes covered by a single ECC step. - $ref: /schemas/types.yaml#/definitions/uint32 - minimum: 1 + $ref: /schemas/types.yaml#/definitions/flag nand-ecc-maximize: - $ref: /schemas/types.yaml#/definitions/flag description: Whether or not the ECC strength should be maximized. The maximum ECC strength is both controller and chip @@ -134,18 +95,19 @@ patternProperties: constraint into account. This is particularly useful when only the in-band area is used by the upper layers, and you want to make your NAND as reliable as possible. + $ref: /schemas/types.yaml#/definitions/flag nand-is-boot-medium: - $ref: /schemas/types.yaml#/definitions/flag description: Whether or not the NAND chip is a boot medium. Drivers might use this information to select ECC algorithms supported by the boot ROM or similar restrictions. + $ref: /schemas/types.yaml#/definitions/flag nand-rb: - $ref: /schemas/types.yaml#/definitions/uint32-array description: Contains the native Ready/Busy IDs. + $ref: /schemas/types.yaml#/definitions/uint32-array rb-gpios: description: @@ -154,12 +116,12 @@ patternProperties: Ready/Busy pins. Active state refers to the NAND ready state and should be set to GPIOD_ACTIVE_HIGH unless the signal is inverted. - secure-regions: - $ref: /schemas/types.yaml#/definitions/uint64-matrix + wp-gpios: description: - Regions in the NAND chip which are protected using a secure element - like Trustzone. This property contains the start address and size of - the secure regions present. + Contains one GPIO descriptor for the Write Protect pin. + Active state refers to the NAND Write Protect state and should be + set to GPIOD_ACTIVE_LOW unless the signal is inverted. + maxItems: 1 required: - reg @@ -181,10 +143,7 @@ examples: nand@0 { reg = <0>; /* Native CS */ - nand-use-soft-ecc-engine; - nand-ecc-algo = "bch"; - - /* controller specific properties */ + /* NAND chip specific properties */ }; nand@1 { diff --git a/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.txt b/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.txt deleted file mode 100644 index d5c5616f6db5..000000000000 --- a/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.txt +++ /dev/null @@ -1,17 +0,0 @@ -ARM AFS - ARM Firmware Suite Partitions -======================================= - -The ARM Firmware Suite is a flash partitioning system found on the -ARM reference designs: Integrator AP, Integrator CP, Versatile AB, -Versatile PB, the RealView family, Versatile Express and Juno. - -Required properties: -- compatible : (required) must be "arm,arm-firmware-suite" - -Example: - -flash@0 { - partitions { - compatible = "arm,arm-firmware-suite"; - }; -}; diff --git a/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.yaml b/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.yaml new file mode 100644 index 000000000000..76c88027b6d2 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.yaml @@ -0,0 +1,28 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/arm,arm-firmware-suite.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Firmware Suite (AFS) Partitions + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + The ARM Firmware Suite is a flash partitioning system found on the + ARM reference designs: Integrator AP, Integrator CP, Versatile AB, + Versatile PB, the RealView family, Versatile Express and Juno. + +properties: + compatible: + const: arm,arm-firmware-suite + +additionalProperties: false + +examples: + - | + partitions { + compatible = "arm,arm-firmware-suite"; + }; +... diff --git a/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.txt b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.txt deleted file mode 100644 index 1d61a029395e..000000000000 --- a/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.txt +++ /dev/null @@ -1,42 +0,0 @@ -Broadcom BCM47xx Partitions -=========================== - -Broadcom is one of hardware manufacturers providing SoCs (BCM47xx) used in -home routers. Their BCM947xx boards using CFE bootloader have several partitions -without any on-flash partition table. On some devices their sizes and/or -meanings can also vary so fixed partitioning can't be used. - -Discovering partitions on these devices is possible thanks to having a special -header and/or magic signature at the beginning of each of them. They are also -block aligned which is important for determinig a size. - -Most of partitions use ASCII text based magic for determining a type. More -complex partitions (like TRX with its HDR0 magic) may include extra header -containing some details, including a length. - -A list of supported partitions includes: -1) Bootloader with Broadcom's CFE (Common Firmware Environment) -2) NVRAM with configuration/calibration data -3) Device manufacturer's data with some default values (e.g. SSIDs) -4) TRX firmware container which can hold up to 4 subpartitions -5) Backup TRX firmware used after failed upgrade - -As mentioned earlier, role of some partitions may depend on extra configuration. -For example both: main firmware and backup firmware use the same TRX format with -the same header. To distinguish currently used firmware a CFE's environment -variable "bootpartition" is used. - - -Devices using Broadcom partitions described above should should have flash node -with a subnode named "partitions" using following properties: - -Required properties: -- compatible : (required) must be "brcm,bcm947xx-cfe-partitions" - -Example: - -flash@0 { - partitions { - compatible = "brcm,bcm947xx-cfe-partitions"; - }; -}; diff --git a/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.yaml b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.yaml new file mode 100644 index 000000000000..3484e06d6bcb --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/brcm,bcm947xx-cfe-partitions.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/brcm,bcm947xx-cfe-partitions.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM47xx Partitions + +description: | + Broadcom is one of hardware manufacturers providing SoCs (BCM47xx) used in + home routers. Their BCM947xx boards using CFE bootloader have several + partitions without any on-flash partition table. On some devices their sizes + and/or meanings can also vary so fixed partitioning can't be used. + + Discovering partitions on these devices is possible thanks to having a special + header and/or magic signature at the beginning of each of them. They are also + block aligned which is important for determinig a size. + + Most of partitions use ASCII text based magic for determining a type. More + complex partitions (like TRX with its HDR0 magic) may include extra header + containing some details, including a length. + + A list of supported partitions includes: + 1) Bootloader with Broadcom's CFE (Common Firmware Environment) + 2) NVRAM with configuration/calibration data + 3) Device manufacturer's data with some default values (e.g. SSIDs) + 4) TRX firmware container which can hold up to 4 subpartitions + 5) Backup TRX firmware used after failed upgrade + + As mentioned earlier, role of some partitions may depend on extra + configuration. For example both: main firmware and backup firmware use the + same TRX format with the same header. To distinguish currently used firmware a + CFE's environment variable "bootpartition" is used. + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +properties: + compatible: + const: brcm,bcm947xx-cfe-partitions + +additionalProperties: false + +examples: + - | + partitions { + compatible = "brcm,bcm947xx-cfe-partitions"; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml b/Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml index ea4cace6a955..ad3ccd250802 100644 --- a/Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml +++ b/Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml @@ -19,7 +19,11 @@ maintainers: properties: compatible: - const: fixed-partitions + oneOf: + - const: fixed-partitions + - items: + - const: sercomm,sc-partitions + - const: fixed-partitions "#address-cells": true @@ -27,7 +31,24 @@ properties: patternProperties: "@[0-9a-f]+$": - $ref: "partition.yaml#" + allOf: + - $ref: "partition.yaml#" + - if: + properties: + compatible: + contains: + const: sercomm,sc-partitions + then: + properties: + sercomm,scpart-id: + description: Partition id in Sercomm partition map. Mtd + parser uses this id to find a record in the partition map + containing offset and size of the current partition. The + values from partition map overrides partition offset and + size defined in reg property of the dts. Frequently these + values are the same, but may differ if device has bad + eraseblocks on a flash. + $ref: /schemas/types.yaml#/definitions/uint32 required: - "#address-cells" @@ -52,6 +73,7 @@ examples: reg = <0x0100000 0x200000>; }; }; + - | partitions { compatible = "fixed-partitions"; @@ -64,6 +86,7 @@ examples: reg = <0x00000000 0x1 0x00000000>; }; }; + - | partitions { compatible = "fixed-partitions"; @@ -82,6 +105,7 @@ examples: reg = <0x2 0x00000000 0x1 0x00000000>; }; }; + - | partitions { compatible = "fixed-partitions"; @@ -119,3 +143,30 @@ examples: }; }; }; + + - | + partitions { + compatible = "sercomm,sc-partitions", "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x100000>; + sercomm,scpart-id = <0>; + read-only; + }; + + partition@100000 { + label = "dynamic partition map"; + reg = <0x100000 0x100000>; + sercomm,scpart-id = <1>; + }; + + partition@200000 { + label = "Factory"; + reg = <0x200000 0x100000>; + sercomm,scpart-id = <2>; + read-only; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/partition.yaml b/Documentation/devicetree/bindings/mtd/partitions/partition.yaml index e1ac08064425..f1a02d840b12 100644 --- a/Documentation/devicetree/bindings/mtd/partitions/partition.yaml +++ b/Documentation/devicetree/bindings/mtd/partitions/partition.yaml @@ -11,6 +11,17 @@ description: | relative offset and size specified. Depending on partition function extra properties can be used. + A partition may be dynamically allocated by a specific parser at runtime. + In this specific case, a specific suffix is required to the node name. + Everything after 'partition-' will be used as the partition name to compare + with the one dynamically allocated by the specific parser. + If the partition contains invalid char a label can be provided that will + be used instead of the node name to make the comparison. + This is used to assign an OF node to the dynamiccally allocated partition + so that subsystem like NVMEM can provide an OF node and declare NVMEM cells. + The OF node will be assigned only if the partition label declared match the + one assigned by the parser at runtime. + maintainers: - Rafał Miłecki <rafal@milecki.pl> @@ -41,7 +52,12 @@ properties: immune to paired-pages corruptions type: boolean -required: - - reg +if: + not: + required: [ reg ] +then: + properties: + $nodename: + pattern: '^partition-.*$' additionalProperties: true diff --git a/Documentation/devicetree/bindings/mtd/partitions/qcom,smem-part.yaml b/Documentation/devicetree/bindings/mtd/partitions/qcom,smem-part.yaml index cf3f8c1e035d..dc07909af023 100644 --- a/Documentation/devicetree/bindings/mtd/partitions/qcom,smem-part.yaml +++ b/Documentation/devicetree/bindings/mtd/partitions/qcom,smem-part.yaml @@ -19,6 +19,10 @@ properties: compatible: const: qcom,smem-part +patternProperties: + "^partition-[0-9a-z]+$": + $ref: partition.yaml# + required: - compatible @@ -31,3 +35,26 @@ examples: compatible = "qcom,smem-part"; }; }; + + - | + /* Example declaring dynamic partition */ + flash { + partitions { + compatible = "qcom,smem-part"; + + partition-art { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + label = "0:art"; + + macaddr_art_0: macaddr@0 { + reg = <0x0 0x6>; + }; + + macaddr_art_6: macaddr@6 { + reg = <0x6 0x6>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partitions/u-boot.yaml b/Documentation/devicetree/bindings/mtd/partitions/u-boot.yaml new file mode 100644 index 000000000000..8a88e7d16524 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/u-boot.yaml @@ -0,0 +1,49 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/partitions/u-boot.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: U-Boot bootloader partition + +description: | + U-Boot is a bootlodaer commonly used in embedded devices. It's almost always + located on some kind of flash device. + + Device configuration is stored as a set of environment variables that are + located in a (usually standalone) block of data. + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +allOf: + - $ref: partition.yaml# + +properties: + compatible: + oneOf: + - const: brcm,u-boot + description: | + Broadcom stores environment variables inside a U-Boot partition. They + can be identified by a custom header with magic value. + +unevaluatedProperties: false + +examples: + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + compatible = "brcm,u-boot"; + reg = <0x0 0x100000>; + label = "u-boot"; + }; + + partition@100000 { + reg = <0x100000 0x1ff00000>; + label = "firmware"; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml b/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml index 84ad7ff30121..482a2c068740 100644 --- a/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml +++ b/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml @@ -102,6 +102,31 @@ allOf: - const: rx - const: cmd + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq806x-nand + + then: + properties: + qcom,boot-partitions: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + items: + - description: offset + - description: size + description: + Boot partition use a different layout where the 4 bytes of spare + data are not protected by ECC. Use this to declare these special + partitions by defining first the offset and then the size. + + It's in the form of <offset1 size1 offset2 size2 offset3 ...> + and should be declared in ascending order. + + Refer to the ipq8064 example on how to use this special binding. + required: - compatible - reg @@ -135,6 +160,8 @@ examples: nand-ecc-strength = <4>; nand-bus-width = <8>; + qcom,boot-partitions = <0x0 0x58a0000>; + partitions { compatible = "fixed-partitions"; #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/mtd/renesas-nandc.yaml b/Documentation/devicetree/bindings/mtd/renesas-nandc.yaml index 2870d36361c4..f0dc78bb0515 100644 --- a/Documentation/devicetree/bindings/mtd/renesas-nandc.yaml +++ b/Documentation/devicetree/bindings/mtd/renesas-nandc.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/mtd/renesas-nandc.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Renesas R-Car Gen3 & RZ/N1x NAND flash controller device tree bindings +title: Renesas R-Car Gen3 & RZ/N1x NAND flash controller maintainers: - Miquel Raynal <miquel.raynal@bootlin.com> @@ -36,11 +36,15 @@ properties: - const: hclk - const: eclk + power-domains: + maxItems: 1 + required: - compatible - reg - clocks - clock-names + - power-domains - interrupts unevaluatedProperties: false @@ -56,6 +60,7 @@ examples: interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; clocks = <&sysctrl R9A06G032_HCLK_NAND>, <&sysctrl R9A06G032_CLK_NAND>; clock-names = "hclk", "eclk"; + power-domains = <&sysctrl>; #address-cells = <1>; #size-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/mtd/rockchip,nand-controller.yaml b/Documentation/devicetree/bindings/mtd/rockchip,nand-controller.yaml index 0922536b1811..d681a4676f06 100644 --- a/Documentation/devicetree/bindings/mtd/rockchip,nand-controller.yaml +++ b/Documentation/devicetree/bindings/mtd/rockchip,nand-controller.yaml @@ -96,8 +96,7 @@ patternProperties: rockchip,boot-ecc-strength: enum: [16, 24, 40, 60, 70] - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32 + $ref: /schemas/types.yaml#/definitions/uint32 description: | If specified it indicates that a different BCH/ECC setting is supported by the boot ROM. diff --git a/Documentation/devicetree/bindings/mtd/spi-nand.txt b/Documentation/devicetree/bindings/mtd/spi-nand.txt deleted file mode 100644 index 8b51f3b6d55c..000000000000 --- a/Documentation/devicetree/bindings/mtd/spi-nand.txt +++ /dev/null @@ -1,5 +0,0 @@ -SPI NAND flash - -Required properties: -- compatible: should be "spi-nand" -- reg: should encode the chip-select line used to access the NAND chip diff --git a/Documentation/devicetree/bindings/mtd/spi-nand.yaml b/Documentation/devicetree/bindings/mtd/spi-nand.yaml new file mode 100644 index 000000000000..4d095e613204 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/spi-nand.yaml @@ -0,0 +1,28 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/spi-nand.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SPI-NAND flash + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +allOf: + - $ref: "nand-chip.yaml#" + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + compatible: + const: spi-nand + + reg: + description: Encode the chip-select line on the SPI bus + maxItems: 1 + +required: + - compatible + - reg + +unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/mtd/ti,elm.yaml b/Documentation/devicetree/bindings/mtd/ti,elm.yaml new file mode 100644 index 000000000000..87128c004596 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/ti,elm.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/ti,elm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments Error Location Module (ELM). + +maintainers: + - Roger Quadros <rogerq@kernel.org> + +description: + ELM module is used together with GPMC and NAND Flash to detect + errors and the location of the error based on BCH algorithms + so they can be corrected if possible. + +properties: + compatible: + enum: + - ti,am3352-elm + - ti,am64-elm + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + description: Functional clock. + + clock-names: + items: + - const: fck + + power-domains: + maxItems: 1 + + ti,hwmods: + description: + Name of the HWMOD associated with ELM. This is for legacy + platforms only. + $ref: /schemas/types.yaml#/definitions/string + deprecated: true + +required: + - compatible + - reg + - interrupts + +allOf: + - if: + properties: + compatible: + contains: + const: ti,am64-elm + then: + required: + - clocks + - clock-names + - power-domains + +additionalProperties: false + +examples: + - | + elm: ecc@0 { + compatible = "ti,am3352-elm"; + reg = <0x0 0x2000>; + interrupts = <4>; + }; |