diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa')
19 files changed, 1914 insertions, 872 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/ar9331.txt b/Documentation/devicetree/bindings/net/dsa/ar9331.txt index 320607cbbb17..f824fdae0da2 100644 --- a/Documentation/devicetree/bindings/net/dsa/ar9331.txt +++ b/Documentation/devicetree/bindings/net/dsa/ar9331.txt @@ -76,7 +76,6 @@ eth1: ethernet@1a000000 { switch_port0: port@0 { reg = <0x0>; - label = "cpu"; ethernet = <ð1>; phy-mode = "gmii"; diff --git a/Documentation/devicetree/bindings/net/dsa/arrow,xrs700x.yaml b/Documentation/devicetree/bindings/net/dsa/arrow,xrs700x.yaml index 3f01b65f3b22..259a0c6547f3 100644 --- a/Documentation/devicetree/bindings/net/dsa/arrow,xrs700x.yaml +++ b/Documentation/devicetree/bindings/net/dsa/arrow,xrs700x.yaml @@ -61,8 +61,9 @@ examples: }; ethernet-port@3 { reg = <3>; - label = "cpu"; ethernet = <&fec1>; + phy-mode = "rgmii-id"; + fixed-link { speed = <1000>; full-duplex; diff --git a/Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml b/Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml index c3c938893ad9..1219b830b1a4 100644 --- a/Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml +++ b/Documentation/devicetree/bindings/net/dsa/brcm,b53.yaml @@ -6,9 +6,6 @@ $schema: http://devicetree.org/meta-schemas/core.yaml# title: Broadcom BCM53xx Ethernet switches -allOf: - - $ref: dsa.yaml# - maintainers: - Florian Fainelli <f.fainelli@gmail.com> @@ -68,53 +65,71 @@ required: - compatible - reg -# BCM585xx/586xx/88312 SoCs -if: - properties: - compatible: - contains: - enum: - - brcm,bcm58522-srab - - brcm,bcm58523-srab - - brcm,bcm58525-srab - - brcm,bcm58622-srab - - brcm,bcm58623-srab - - brcm,bcm58625-srab - - brcm,bcm88312-srab -then: - properties: - reg: - minItems: 3 - maxItems: 3 - reg-names: - items: - - const: srab - - const: mux_config - - const: sgmii_config - interrupts: - minItems: 13 - maxItems: 13 - interrupt-names: - items: - - const: link_state_p0 - - const: link_state_p1 - - const: link_state_p2 - - const: link_state_p3 - - const: link_state_p4 - - const: link_state_p5 - - const: link_state_p7 - - const: link_state_p8 - - const: phy - - const: ts - - const: imp_sleep_timer_p5 - - const: imp_sleep_timer_p7 - - const: imp_sleep_timer_p8 - required: - - interrupts -else: - properties: - reg: - maxItems: 1 +allOf: + - $ref: dsa.yaml# + - if: + properties: + compatible: + contains: + enum: + - brcm,bcm5325 + - brcm,bcm53115 + - brcm,bcm53125 + - brcm,bcm53128 + - brcm,bcm5365 + - brcm,bcm5395 + - brcm,bcm5397 + - brcm,bcm5398 + then: + $ref: /schemas/spi/spi-peripheral-props.yaml + + # BCM585xx/586xx/88312 SoCs + - if: + properties: + compatible: + contains: + enum: + - brcm,bcm58522-srab + - brcm,bcm58523-srab + - brcm,bcm58525-srab + - brcm,bcm58622-srab + - brcm,bcm58623-srab + - brcm,bcm58625-srab + - brcm,bcm88312-srab + then: + properties: + reg: + minItems: 3 + maxItems: 3 + reg-names: + items: + - const: srab + - const: mux_config + - const: sgmii_config + interrupts: + minItems: 13 + maxItems: 13 + interrupt-names: + items: + - const: link_state_p0 + - const: link_state_p1 + - const: link_state_p2 + - const: link_state_p3 + - const: link_state_p4 + - const: link_state_p5 + - const: link_state_p7 + - const: link_state_p8 + - const: phy + - const: ts + - const: imp_sleep_timer_p5 + - const: imp_sleep_timer_p7 + - const: imp_sleep_timer_p8 + required: + - interrupts + else: + properties: + reg: + maxItems: 1 unevaluatedProperties: false @@ -154,7 +169,6 @@ examples: port@8 { reg = <8>; - label = "cpu"; phy-mode = "rgmii-txid"; ethernet = <ð0>; fixed-link { @@ -237,8 +251,9 @@ examples: port@8 { ethernet = <&amac2>; - label = "cpu"; reg = <8>; + phy-mode = "internal"; + fixed-link { speed = <1000>; full-duplex; diff --git a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml index 702df848a71d..10ad7e71097b 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml +++ b/Documentation/devicetree/bindings/net/dsa/dsa-port.yaml @@ -15,7 +15,7 @@ description: Ethernet switch port Description allOf: - - $ref: "http://devicetree.org/schemas/net/ethernet-controller.yaml#" + - $ref: /schemas/net/ethernet-controller.yaml# properties: reg: @@ -34,6 +34,8 @@ properties: full routing information must be given, not just the one hop routes to neighbouring switches $ref: /schemas/types.yaml#/definitions/phandle-array + items: + maxItems: 1 ethernet: description: @@ -51,6 +53,8 @@ properties: - edsa - ocelot - ocelot-8021q + - rtl8_4 + - rtl8_4t - seville phy-handle: true @@ -72,6 +76,23 @@ properties: required: - reg +# CPU and DSA ports must have phylink-compatible link descriptions +if: + oneOf: + - required: [ ethernet ] + - required: [ link ] +then: + allOf: + - required: + - phy-mode + - oneOf: + - required: + - fixed-link + - required: + - phy-handle + - required: + - managed + additionalProperties: true ... diff --git a/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml b/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml index 5592f58fa6f0..73b774eadd0b 100644 --- a/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml +++ b/Documentation/devicetree/bindings/net/dsa/hirschmann,hellcreek.yaml @@ -48,7 +48,7 @@ properties: "^led@[01]$": type: object description: Hellcreek leds - $ref: ../../leds/common.yaml# + $ref: /schemas/leds/common.yaml# properties: reg: @@ -91,8 +91,13 @@ examples: port@0 { reg = <0>; - label = "cpu"; ethernet = <&gmac0>; + phy-mode = "mii"; + + fixed-link { + speed = <100>; + full-duplex; + }; }; port@2 { diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt index 464d6bf87605..46a732087f5c 100644 --- a/Documentation/devicetree/bindings/net/dsa/lan9303.txt +++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt @@ -46,7 +46,6 @@ I2C managed mode: port@0 { /* RMII fixed link to master */ reg = <0>; - label = "cpu"; ethernet = <&master>; }; @@ -83,7 +82,6 @@ MDIO managed mode: port@0 { reg = <0>; - label = "cpu"; ethernet = <&master>; }; diff --git a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt index e3829d3e480e..8bb1eff21cb1 100644 --- a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt +++ b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt @@ -96,7 +96,6 @@ switch@e108000 { port@6 { reg = <0x6>; - label = "cpu"; ethernet = <ð0>; }; }; diff --git a/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml new file mode 100644 index 000000000000..f2e9ff3f580b --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml @@ -0,0 +1,804 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/mediatek,mt7530.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT7530 and MT7531 Ethernet Switches + +maintainers: + - Arınç ÜNAL <arinc.unal@arinc9.com> + - Landen Chao <Landen.Chao@mediatek.com> + - DENG Qingfang <dqfext@gmail.com> + - Sean Wang <sean.wang@mediatek.com> + +description: | + There are two versions of MT7530, standalone and in a multi-chip module. + + MT7530 is a part of the multi-chip module in MT7620AN, MT7620DA, MT7620DAN, + MT7620NN, MT7621AT, MT7621DAT, MT7621ST and MT7623AI SoCs. + + MT7530 in MT7620AN, MT7620DA, MT7620DAN and MT7620NN SoCs has got 10/100 PHYs + and the switch registers are directly mapped into SoC's memory map rather than + using MDIO. The DSA driver currently doesn't support this. + + There is only the standalone version of MT7531. + + Port 5 on MT7530 has got various ways of configuration. + + For standalone MT7530: + + - Port 5 can be used as a CPU port. + + - PHY 0 or 4 of the switch can be muxed to connect to the gmac of the SoC + which port 5 is wired to. Usually used for connecting the wan port + directly to the CPU to achieve 2 Gbps routing in total. + + The driver looks up the reg on the ethernet-phy node which the phy-handle + property refers to on the gmac node to mux the specified phy. + + The driver requires the gmac of the SoC to have "mediatek,eth-mac" as the + compatible string and the reg must be 1. So, for now, only gmac1 of an + MediaTek SoC can benefit this. Banana Pi BPI-R2 suits this. + Check out example 5 for a similar configuration. + + - Port 5 can be wired to an external phy. Port 5 becomes a DSA slave. + Check out example 7 for a similar configuration. + + For multi-chip module MT7530: + + - Port 5 can be used as a CPU port. + + - PHY 0 or 4 of the switch can be muxed to connect to gmac1 of the SoC. + Usually used for connecting the wan port directly to the CPU to achieve 2 + Gbps routing in total. + + The driver looks up the reg on the ethernet-phy node which the phy-handle + property refers to on the gmac node to mux the specified phy. + + For the MT7621 SoCs, rgmii2 group must be claimed with rgmii2 function. + Check out example 5. + + - In case of an external phy wired to gmac1 of the SoC, port 5 must not be + enabled. + + In case of muxing PHY 0 or 4, the external phy must not be enabled. + + For the MT7621 SoCs, rgmii2 group must be claimed with rgmii2 function. + Check out example 6. + + - Port 5 can be muxed to an external phy. Port 5 becomes a DSA slave. + The external phy must be wired TX to TX to gmac1 of the SoC for this to + work. Ubiquiti EdgeRouter X SFP is wired this way. + + Muxing PHY 0 or 4 won't work when the external phy is connected TX to TX. + + For the MT7621 SoCs, rgmii2 group must be claimed with gpio function. + Check out example 7. + +properties: + compatible: + oneOf: + - description: + Standalone MT7530 and multi-chip module MT7530 in MT7623AI SoC + const: mediatek,mt7530 + + - description: + Standalone MT7531 + const: mediatek,mt7531 + + - description: + Multi-chip module MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs + const: mediatek,mt7621 + + reg: + maxItems: 1 + + core-supply: + description: + Phandle to the regulator node necessary for the core power. + + "#gpio-cells": + const: 2 + + gpio-controller: + type: boolean + description: + If defined, LED controller of the MT7530 switch will run on GPIO mode. + + There are 15 controllable pins. + port 0 LED 0..2 as GPIO 0..2 + port 1 LED 0..2 as GPIO 3..5 + port 2 LED 0..2 as GPIO 6..8 + port 3 LED 0..2 as GPIO 9..11 + port 4 LED 0..2 as GPIO 12..14 + + "#interrupt-cells": + const: 1 + + interrupt-controller: true + + interrupts: + maxItems: 1 + + io-supply: + description: + Phandle to the regulator node necessary for the I/O power. + See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt for + details for the regulator setup on these boards. + + mediatek,mcm: + type: boolean + description: + Used for MT7621AT, MT7621DAT, MT7621ST and MT7623AI SoCs which the MT7530 + switch is a part of the multi-chip module. + + reset-gpios: + description: + GPIO to reset the switch. Use this if mediatek,mcm is not used. + This property is optional because some boards share the reset line with + other components which makes it impossible to probe the switch if the + reset line is used. + maxItems: 1 + + reset-names: + const: mcm + + resets: + description: + Phandle pointing to the system reset controller with line index for the + ethsys. + maxItems: 1 + +patternProperties: + "^(ethernet-)?ports$": + type: object + + patternProperties: + "^(ethernet-)?port@[0-9]+$": + type: object + description: Ethernet switch ports + + unevaluatedProperties: false + + properties: + reg: + description: + Port address described must be 5 or 6 for CPU port and from 0 to 5 + for user ports. + + allOf: + - $ref: dsa-port.yaml# + - if: + required: [ ethernet ] + then: + properties: + reg: + enum: + - 5 + - 6 + +required: + - compatible + - reg + +$defs: + mt7530-dsa-port: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-9]+$": + if: + required: [ ethernet ] + then: + if: + properties: + reg: + const: 5 + then: + properties: + phy-mode: + enum: + - gmii + - mii + - rgmii + else: + properties: + phy-mode: + enum: + - rgmii + - trgmii + + mt7531-dsa-port: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-9]+$": + if: + required: [ ethernet ] + then: + if: + properties: + reg: + const: 5 + then: + properties: + phy-mode: + enum: + - 1000base-x + - 2500base-x + - rgmii + - sgmii + else: + properties: + phy-mode: + enum: + - 1000base-x + - 2500base-x + - sgmii + +allOf: + - $ref: dsa.yaml# + - if: + required: + - mediatek,mcm + then: + properties: + reset-gpios: false + + required: + - resets + - reset-names + + - dependencies: + interrupt-controller: [ interrupts ] + + - if: + properties: + compatible: + const: mediatek,mt7530 + then: + $ref: "#/$defs/mt7530-dsa-port" + required: + - core-supply + - io-supply + + - if: + properties: + compatible: + const: mediatek,mt7531 + then: + $ref: "#/$defs/mt7531-dsa-port" + properties: + gpio-controller: false + mediatek,mcm: false + + - if: + properties: + compatible: + const: mediatek,mt7621 + then: + $ref: "#/$defs/mt7530-dsa-port" + required: + - mediatek,mcm + +unevaluatedProperties: false + +examples: + # Example 1: Standalone MT7530 + - | + #include <dt-bindings/gpio/gpio.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@1f { + compatible = "mediatek,mt7530"; + reg = <0x1f>; + + reset-gpios = <&pio 33 0>; + + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 2: MT7530 in MT7623AI SoC + - | + #include <dt-bindings/reset/mt2701-resets.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@1f { + compatible = "mediatek,mt7530"; + reg = <0x1f>; + + mediatek,mcm; + resets = <ðsys MT2701_ETHSYS_MCM_RST>; + reset-names = "mcm"; + + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 3: Standalone MT7531 + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@0 { + compatible = "mediatek,mt7531"; + reg = <0>; + + reset-gpios = <&pio 54 0>; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <53 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 4: MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 5: MT7621: mux MT7530's phy4 to SoC's gmac1 + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + + phy-mode = "rgmii"; + phy-handle = <&example5_ethphy4>; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* MT7530's phy4 */ + example5_ethphy4: ethernet-phy@4 { + reg = <4>; + }; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + /* Commented out, phy4 is muxed to gmac1. + port@4 { + reg = <4>; + label = "wan"; + }; + */ + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + }; + + # Example 6: MT7621: mux external phy to SoC's gmac1 + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + + phy-mode = "rgmii"; + phy-handle = <&example6_ethphy7>; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* External PHY */ + example6_ethphy7: ethernet-phy@7 { + reg = <7>; + phy-mode = "rgmii"; + }; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + }; + + # Example 7: MT7621: mux external phy to MT7530's port 5 + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* External PHY */ + example7_ethphy7: ethernet-phy@7 { + reg = <7>; + phy-mode = "rgmii"; + }; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@5 { + reg = <5>; + label = "extphy"; + phy-mode = "rgmii-txid"; + phy-handle = <&example7_ethphy7>; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml index 84985f53bffd..4da75b1f9533 100644 --- a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml +++ b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml @@ -12,6 +12,7 @@ maintainers: allOf: - $ref: dsa.yaml# + - $ref: /schemas/spi/spi-peripheral-props.yaml# properties: # See Documentation/devicetree/bindings/net/dsa/dsa.yaml for a list of additional @@ -42,6 +43,12 @@ properties: description: Set if the output SYNCLKO frequency should be set to 125MHz instead of 25MHz. + microchip,synclko-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set if the output SYNCLKO clock should be disabled. Do not mix with + microchip,synclko-125. + required: - compatible - reg @@ -100,8 +107,9 @@ examples: }; port@5 { reg = <5>; - label = "cpu"; ethernet = <ð0>; + phy-mode = "rgmii"; + fixed-link { speed = <1000>; full-duplex; @@ -137,8 +145,9 @@ examples: }; port@6 { reg = <6>; - label = "cpu"; ethernet = <ð0>; + phy-mode = "rgmii"; + fixed-link { speed = <1000>; full-duplex; diff --git a/Documentation/devicetree/bindings/net/dsa/microchip,lan937x.yaml b/Documentation/devicetree/bindings/net/dsa/microchip,lan937x.yaml new file mode 100644 index 000000000000..630bf0f8294b --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/microchip,lan937x.yaml @@ -0,0 +1,192 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/microchip,lan937x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LAN937x Ethernet Switch Series Tree Bindings + +maintainers: + - UNGLinuxDriver@microchip.com + +allOf: + - $ref: dsa.yaml# + +properties: + compatible: + enum: + - microchip,lan9370 + - microchip,lan9371 + - microchip,lan9372 + - microchip,lan9373 + - microchip,lan9374 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 50000000 + + reset-gpios: + description: Optional gpio specifier for a reset line + maxItems: 1 + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + +patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-9]+$": + allOf: + - if: + properties: + phy-mode: + contains: + enum: + - rgmii + - rgmii-id + - rgmii-txid + - rgmii-rxid + then: + properties: + rx-internal-delay-ps: + enum: [0, 2000] + default: 0 + tx-internal-delay-ps: + enum: [0, 2000] + default: 0 + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + macb0 { + #address-cells = <1>; + #size-cells = <0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + spi { + #address-cells = <1>; + #size-cells = <0>; + + lan9374: switch@0 { + compatible = "microchip,lan9374"; + reg = <0>; + spi-max-frequency = <44000000>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&t1phy0>; + }; + + port@1 { + reg = <1>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&t1phy1>; + }; + + port@2 { + reg = <2>; + label = "lan4"; + phy-mode = "internal"; + phy-handle = <&t1phy2>; + }; + + port@3 { + reg = <3>; + label = "lan6"; + phy-mode = "internal"; + phy-handle = <&t1phy3>; + }; + + port@4 { + reg = <4>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <2000>; + ethernet = <&macb0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@5 { + reg = <5>; + label = "lan7"; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <2000>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@6 { + reg = <6>; + label = "lan5"; + phy-mode = "internal"; + phy-handle = <&t1phy6>; + }; + + port@7 { + reg = <7>; + label = "lan3"; + phy-mode = "internal"; + phy-handle = <&t1phy7>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + t1phy0: ethernet-phy@0{ + reg = <0x0>; + }; + + t1phy1: ethernet-phy@1{ + reg = <0x1>; + }; + + t1phy2: ethernet-phy@2{ + reg = <0x2>; + }; + + t1phy3: ethernet-phy@3{ + reg = <0x3>; + }; + + t1phy6: ethernet-phy@6{ + reg = <0x6>; + }; + + t1phy7: ethernet-phy@7{ + reg = <0x7>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml b/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml new file mode 100644 index 000000000000..8d93ed9c172c --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/mscc,ocelot.yaml @@ -0,0 +1,260 @@ +# SPDX-License-Identifier: (GPL-2.0 OR MIT) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/mscc,ocelot.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip Ocelot Switch Family Device Tree Bindings + +maintainers: + - Vladimir Oltean <vladimir.oltean@nxp.com> + - Claudiu Manoil <claudiu.manoil@nxp.com> + - Alexandre Belloni <alexandre.belloni@bootlin.com> + - UNGLinuxDriver@microchip.com + +description: | + There are multiple switches which are either part of the Ocelot-1 family, or + derivatives of this architecture. These switches can be found embedded in + various SoCs and accessed using MMIO, or as discrete chips and accessed over + SPI or PCIe. The present DSA binding shall be used when the host controlling + them performs packet I/O primarily through an Ethernet port of the switch + (which is attached to an Ethernet port of the host), rather than through + Frame DMA or register-based I/O. + + VSC9953 (Seville): + + This is found in the NXP T1040, where it is a memory-mapped platform + device. + + The following PHY interface types are supported: + + - phy-mode = "internal": on ports 8 and 9 + - phy-mode = "sgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 + - phy-mode = "qsgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 + - phy-mode = "1000base-x": on ports 0, 1, 2, 3, 4, 5, 6, 7 + + VSC9959 (Felix): + + This is found in the NXP LS1028A. It is a PCI device, part of the larger + enetc root complex. As a result, the ethernet-switch node is a sub-node of + the PCIe root complex node and its "reg" property conforms to the parent + node bindings, describing it as PF 5 of device 0, bus 0. + + If any external switch port is enabled, the enetc PF2 (enetc_port2) should + be enabled as well. This is because the internal MDIO bus (exposed through + EA BAR 0) used to access the MAC PCS registers truly belongs to the enetc + port 2 and not to Felix. + + The following PHY interface types are supported: + + - phy-mode = "internal": on ports 4 and 5 + - phy-mode = "sgmii": on ports 0, 1, 2, 3 + - phy-mode = "qsgmii": on ports 0, 1, 2, 3 + - phy-mode = "usxgmii": on ports 0, 1, 2, 3 + - phy-mode = "1000base-x": on ports 0, 1, 2, 3 + - phy-mode = "2500base-x": on ports 0, 1, 2, 3 + +properties: + compatible: + enum: + - mscc,vsc9953-switch + - pci1957,eef0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + description: + Used to signal availability of PTP TX timestamps, and state changes of + the MAC merge layer of ports that support Frame Preemption. + + little-endian: true + big-endian: true + +required: + - compatible + - reg + +allOf: + - $ref: dsa.yaml# + - if: + properties: + compatible: + const: pci1957,eef0 + then: + required: + - interrupts + +unevaluatedProperties: false + +examples: + # Felix VSC9959 (NXP LS1028A) + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pcie { /* Integrated Endpoint Root Complex */ + #address-cells = <3>; + #size-cells = <2>; + + ethernet-switch@0,5 { + compatible = "pci1957,eef0"; + reg = <0x000500 0 0 0 0>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + phy-mode = "qsgmii"; + phy-handle = <&phy0>; + managed = "in-band-status"; + }; + + port@1 { + reg = <1>; + phy-mode = "qsgmii"; + phy-handle = <&phy1>; + managed = "in-band-status"; + }; + + port@2 { + reg = <2>; + phy-mode = "qsgmii"; + phy-handle = <&phy2>; + managed = "in-band-status"; + }; + + port@3 { + reg = <3>; + phy-mode = "qsgmii"; + phy-handle = <&phy3>; + managed = "in-band-status"; + }; + + port@4 { + reg = <4>; + ethernet = <&enetc_port2>; + phy-mode = "internal"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + port@5 { + reg = <5>; + ethernet = <&enetc_port3>; + phy-mode = "internal"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + # Seville VSC9953 (NXP T1040) + - | + soc { + #address-cells = <1>; + #size-cells = <1>; + + ethernet-switch@800000 { + compatible = "mscc,vsc9953-switch"; + reg = <0x800000 0x290000>; + little-endian; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + phy-mode = "qsgmii"; + phy-handle = <&phy0>; + managed = "in-band-status"; + }; + + port@1 { + reg = <1>; + phy-mode = "qsgmii"; + phy-handle = <&phy1>; + managed = "in-band-status"; + }; + + port@2 { + reg = <2>; + phy-mode = "qsgmii"; + phy-handle = <&phy2>; + managed = "in-band-status"; + }; + + port@3 { + reg = <3>; + phy-mode = "qsgmii"; + phy-handle = <&phy3>; + managed = "in-band-status"; + }; + + port@4 { + reg = <4>; + phy-mode = "qsgmii"; + phy-handle = <&phy4>; + managed = "in-band-status"; + }; + + port@5 { + reg = <5>; + phy-mode = "qsgmii"; + phy-handle = <&phy5>; + managed = "in-band-status"; + }; + + port@6 { + reg = <6>; + phy-mode = "qsgmii"; + phy-handle = <&phy6>; + managed = "in-band-status"; + }; + + port@7 { + reg = <7>; + phy-mode = "qsgmii"; + phy-handle = <&phy7>; + managed = "in-band-status"; + }; + + port@8 { + reg = <8>; + phy-mode = "internal"; + ethernet = <&enet0>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + port@9 { + reg = <9>; + phy-mode = "internal"; + ethernet = <&enet1>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt deleted file mode 100644 index 18247ebfc487..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/mt7530.txt +++ /dev/null @@ -1,327 +0,0 @@ -Mediatek MT7530 Ethernet switch -================================ - -Required properties: - -- compatible: may be compatible = "mediatek,mt7530" - or compatible = "mediatek,mt7621" - or compatible = "mediatek,mt7531" -- #address-cells: Must be 1. -- #size-cells: Must be 0. -- mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part - on multi-chip module belong to MT7623A has or the remotely standalone - chip as the function MT7623N reference board provided for. - -If compatible mediatek,mt7530 is set then the following properties are required - -- core-supply: Phandle to the regulator node necessary for the core power. -- io-supply: Phandle to the regulator node necessary for the I/O power. - See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt - for details for the regulator setup on these boards. - -If the property mediatek,mcm isn't defined, following property is required - -- reset-gpios: Should be a gpio specifier for a reset line. - -Else, following properties are required - -- resets : Phandle pointing to the system reset controller with - line index for the ethsys. -- reset-names : Should be set to "mcm". - -Required properties for the child nodes within ports container: - -- reg: Port address described must be 6 for CPU port and from 0 to 5 for - user ports. -- phy-mode: String, the following values are acceptable for port labeled - "cpu": - If compatible mediatek,mt7530 or mediatek,mt7621 is set, - must be either "trgmii" or "rgmii" - If compatible mediatek,mt7531 is set, - must be either "sgmii", "1000base-x" or "2500base-x" - -Port 5 of mt7530 and mt7621 switch is muxed between: -1. GMAC5: GMAC5 can interface with another external MAC or PHY. -2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC - of the SOC. Used in many setups where port 0/4 becomes the WAN port. - Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to - GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not - connected to external component! - -Port 5 modes/configurations: -1. Port 5 is disabled and isolated: An external phy can interface to the 2nd - GMAC of the SOC. - In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd - GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC! -2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC. - It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode - and RGMII delay. -3. Port 5 is muxed to GMAC5 and can interface to an external phy. - Port 5 becomes an extra switch port. - Only works on platform where external phy TX<->RX lines are swapped. - Like in the Ubiquiti ER-X-SFP. -4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port. - Currently a 2nd CPU port is not supported by DSA code. - -Depending on how the external PHY is wired: -1. normal: The PHY can only connect to 2nd GMAC but not to the switch -2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as - a ethernet port. But can't interface to the 2nd GMAC. - -Based on the DT the port 5 mode is configured. - -Driver tries to lookup the phy-handle of the 2nd GMAC of the master device. -When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2. -phy-mode must be set, see also example 2 below! - * mt7621: phy-mode = "rgmii-txid"; - * mt7623: phy-mode = "rgmii"; - -Optional properties: - -- gpio-controller: Boolean; if defined, MT7530's LED controller will run on - GPIO mode. -- #gpio-cells: Must be 2 if gpio-controller is defined. -- interrupt-controller: Boolean; Enables the internal interrupt controller. - -If interrupt-controller is defined, the following properties are required. - -- #interrupt-cells: Must be 1. -- interrupts: Parent interrupt for the interrupt controller. - -See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional -required, optional properties and how the integrated switch subnodes must -be specified. - -Example: - - &mdio0 { - switch@0 { - compatible = "mediatek,mt7530"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - - core-supply = <&mt6323_vpa_reg>; - io-supply = <&mt6323_vemc3v3_reg>; - reset-gpios = <&pio 33 0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - port@0 { - reg = <0>; - label = "lan0"; - }; - - port@1 { - reg = <1>; - label = "lan1"; - }; - - port@2 { - reg = <2>; - label = "lan2"; - }; - - port@3 { - reg = <3>; - label = "lan3"; - }; - - port@4 { - reg = <4>; - label = "wan"; - }; - - port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "trgmii"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; - }; - -Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4. - -ð { - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "rgmii"; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - - gmac1: mac@1 { - compatible = "mediatek,eth-mac"; - reg = <1>; - phy-mode = "rgmii-txid"; - phy-handle = <&phy4>; - }; - - mdio: mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - - /* Internal phy */ - phy4: ethernet-phy@4 { - reg = <4>; - }; - - mt7530: switch@1f { - compatible = "mediatek,mt7621"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x1f>; - pinctrl-names = "default"; - mediatek,mcm; - - resets = <&rstctrl 2>; - reset-names = "mcm"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "lan0"; - }; - - port@1 { - reg = <1>; - label = "lan1"; - }; - - port@2 { - reg = <2>; - label = "lan2"; - }; - - port@3 { - reg = <3>; - label = "lan3"; - }; - -/* Commented out. Port 4 is handled by 2nd GMAC. - port@4 { - reg = <4>; - label = "lan4"; - }; -*/ - - cpu_port0: port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "rgmii"; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - }; - }; - }; -}; - -Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY. - -ð { - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "rgmii"; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - - mdio: mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - - /* External phy */ - ephy5: ethernet-phy@7 { - reg = <7>; - }; - - mt7530: switch@1f { - compatible = "mediatek,mt7621"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x1f>; - pinctrl-names = "default"; - mediatek,mcm; - - resets = <&rstctrl 2>; - reset-names = "mcm"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "lan0"; - }; - - port@1 { - reg = <1>; - label = "lan1"; - }; - - port@2 { - reg = <2>; - label = "lan2"; - }; - - port@3 { - reg = <3>; - label = "lan3"; - }; - - port@4 { - reg = <4>; - label = "lan4"; - }; - - port@5 { - reg = <5>; - label = "lan5"; - phy-mode = "rgmii"; - phy-handle = <&ephy5>; - }; - - cpu_port0: port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "rgmii"; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml index 24cd733c11d1..1e26d876d146 100644 --- a/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml +++ b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml @@ -14,6 +14,7 @@ description: allOf: - $ref: "dsa.yaml#" + - $ref: /schemas/spi/spi-peripheral-props.yaml# maintainers: - Vladimir Oltean <vladimir.oltean@nxp.com> @@ -52,10 +53,8 @@ properties: patternProperties: "^mdio@[0-1]$": - type: object - - allOf: - - $ref: "http://devicetree.org/schemas/net/mdio.yaml#" + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false properties: compatible: diff --git a/Documentation/devicetree/bindings/net/dsa/ocelot.txt b/Documentation/devicetree/bindings/net/dsa/ocelot.txt deleted file mode 100644 index 7a271d070b72..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/ocelot.txt +++ /dev/null @@ -1,213 +0,0 @@ -Microchip Ocelot switch driver family -===================================== - -Felix ------ - -Currently the switches supported by the felix driver are: - -- VSC9959 (Felix) -- VSC9953 (Seville) - -The VSC9959 switch is found in the NXP LS1028A. It is a PCI device, part of the -larger ENETC root complex. As a result, the ethernet-switch node is a sub-node -of the PCIe root complex node and its "reg" property conforms to the parent -node bindings: - -* reg: Specifies PCIe Device Number and Function Number of the endpoint device, - in this case for the Ethernet L2Switch it is PF5 (of device 0, bus 0). - -It does not require a "compatible" string. - -The interrupt line is used to signal availability of PTP TX timestamps and for -TSN frame preemption. - -For the external switch ports, depending on board configuration, "phy-mode" and -"phy-handle" are populated by board specific device tree instances. Ports 4 and -5 are fixed as internal ports in the NXP LS1028A instantiation. - -The CPU port property ("ethernet") configures the feature called "NPI port" in -the Ocelot hardware core. The CPU port in Ocelot is a set of queues, which are -connected, in the Node Processor Interface (NPI) mode, to an Ethernet port. -By default, in fsl-ls1028a.dtsi, the NPI port is assigned to the internal -2.5Gbps port@4, but can be moved to the 1Gbps port@5, depending on the specific -use case. Moving the NPI port to an external switch port is hardware possible, -but there is no platform support for the Linux system on the LS1028A chip to -operate as an entire slave DSA chip. NPI functionality (and therefore DSA -tagging) is supported on a single port at a time. - -Any port can be disabled (and in fsl-ls1028a.dtsi, they are indeed all disabled -by default, and should be enabled on a per-board basis). But if any external -switch port is enabled at all, the ENETC PF2 (enetc_port2) should be enabled as -well, regardless of whether it is configured as the DSA master or not. This is -because the Felix PHYLINK implementation accesses the MAC PCS registers, which -in hardware truly belong to the ENETC port #2 and not to Felix. - -Supported PHY interface types (appropriate SerDes protocol setting changes are -needed in the RCW binary): - -* phy_mode = "internal": on ports 4 and 5 -* phy_mode = "sgmii": on ports 0, 1, 2, 3 -* phy_mode = "qsgmii": on ports 0, 1, 2, 3 -* phy_mode = "usxgmii": on ports 0, 1, 2, 3 -* phy_mode = "2500base-x": on ports 0, 1, 2, 3 - -For the rest of the device tree binding definitions, which are standard DSA and -PCI, refer to the following documents: - -Documentation/devicetree/bindings/net/dsa/dsa.txt -Documentation/devicetree/bindings/pci/pci.txt - -Example: - -&soc { - pcie@1f0000000 { /* Integrated Endpoint Root Complex */ - ethernet-switch@0,5 { - reg = <0x000500 0 0 0 0>; - /* IEP INT_B */ - interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - /* External ports */ - port@0 { - reg = <0>; - label = "swp0"; - }; - - port@1 { - reg = <1>; - label = "swp1"; - }; - - port@2 { - reg = <2>; - label = "swp2"; - }; - - port@3 { - reg = <3>; - label = "swp3"; - }; - - /* Tagging CPU port */ - port@4 { - reg = <4>; - ethernet = <&enetc_port2>; - phy-mode = "internal"; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - - /* Non-tagging CPU port */ - port@5 { - reg = <5>; - phy-mode = "internal"; - status = "disabled"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; - }; -}; - -The VSC9953 switch is found inside NXP T1040. It is a platform device with the -following required properties: - -- compatible: - Must be "mscc,vsc9953-switch". - -Supported PHY interface types (appropriate SerDes protocol setting changes are -needed in the RCW binary): - -* phy_mode = "internal": on ports 8 and 9 -* phy_mode = "sgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 -* phy_mode = "qsgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 - -Example: - -&soc { - ethernet-switch@800000 { - #address-cells = <0x1>; - #size-cells = <0x0>; - compatible = "mscc,vsc9953-switch"; - little-endian; - reg = <0x800000 0x290000>; - - ports { - #address-cells = <0x1>; - #size-cells = <0x0>; - - port@0 { - reg = <0x0>; - label = "swp0"; - }; - - port@1 { - reg = <0x1>; - label = "swp1"; - }; - - port@2 { - reg = <0x2>; - label = "swp2"; - }; - - port@3 { - reg = <0x3>; - label = "swp3"; - }; - - port@4 { - reg = <0x4>; - label = "swp4"; - }; - - port@5 { - reg = <0x5>; - label = "swp5"; - }; - - port@6 { - reg = <0x6>; - label = "swp6"; - }; - - port@7 { - reg = <0x7>; - label = "swp7"; - }; - - port@8 { - reg = <0x8>; - phy-mode = "internal"; - ethernet = <&enet0>; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - - port@9 { - reg = <0x9>; - phy-mode = "internal"; - status = "disabled"; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.yaml b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml index 89c21b289447..978162df51f7 100644 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.yaml +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml @@ -58,33 +58,14 @@ properties: B68 on the QCA832x and B49 on the QCA833x. mdio: - type: object + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false description: Qca8k switch have an internal mdio to access switch port. If this is not present, the legacy mapping is used and the internal mdio access is used. With the legacy mapping the reg corresponding to the internal mdio is the switch reg with an offset of -1. - properties: - '#address-cells': - const: 1 - '#size-cells': - const: 0 - - patternProperties: - "^(ethernet-)?phy@[0-4]$": - type: object - - allOf: - - $ref: "http://devicetree.org/schemas/net/mdio.yaml#" - - properties: - reg: - maxItems: 1 - - required: - - reg - patternProperties: "^(ethernet-)?ports$": type: object @@ -178,7 +159,6 @@ examples: port@0 { reg = <0>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "rgmii"; @@ -240,7 +220,6 @@ examples: port@0 { reg = <0>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "rgmii"; @@ -287,7 +266,6 @@ examples: port@6 { reg = <0>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "sgmii"; diff --git a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt deleted file mode 100644 index 7959ec237983..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt +++ /dev/null @@ -1,240 +0,0 @@ -Realtek SMI-based Switches -========================== - -The SMI "Simple Management Interface" is a two-wire protocol using -bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does -not use the MDIO protocol. This binding defines how to specify the -SMI-based Realtek devices. - -Required properties: - -- compatible: must be exactly one of: - "realtek,rtl8365mb" (4+1 ports) - "realtek,rtl8366" - "realtek,rtl8366rb" (4+1 ports) - "realtek,rtl8366s" (4+1 ports) - "realtek,rtl8367" - "realtek,rtl8367b" - "realtek,rtl8368s" (8 port) - "realtek,rtl8369" - "realtek,rtl8370" (8 port) - -Required properties: -- mdc-gpios: GPIO line for the MDC clock line. -- mdio-gpios: GPIO line for the MDIO data line. -- reset-gpios: GPIO line for the reset signal. - -Optional properties: -- realtek,disable-leds: if the LED drivers are not used in the - hardware design this will disable them so they are not turned on - and wasting power. - -Required subnodes: - -- interrupt-controller - - This defines an interrupt controller with an IRQ line (typically - a GPIO) that will demultiplex and handle the interrupt from the single - interrupt line coming out of one of the SMI-based chips. It most - importantly provides link up/down interrupts to the PHY blocks inside - the ASIC. - -Required properties of interrupt-controller: - -- interrupt: parent interrupt, see interrupt-controller/interrupts.txt -- interrupt-controller: see interrupt-controller/interrupts.txt -- #address-cells: should be <0> -- #interrupt-cells: should be <1> - -- mdio - - This defines the internal MDIO bus of the SMI device, mostly for the - purpose of being able to hook the interrupts to the right PHY and - the right PHY to the corresponding port. - -Required properties of mdio: - -- compatible: should be set to "realtek,smi-mdio" for all SMI devices - -See net/mdio.txt for additional MDIO bus properties. - -See net/dsa/dsa.txt for a list of additional required and optional properties -and subnodes of DSA switches. - -Examples: - -An example for the RTL8366RB: - -switch { - compatible = "realtek,rtl8366rb"; - /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ - mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; - mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; - - switch_intc: interrupt-controller { - /* GPIO 15 provides the interrupt */ - interrupt-parent = <&gpio0>; - interrupts = <15 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <1>; - }; - - ports { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - port@0 { - reg = <0>; - label = "lan0"; - phy-handle = <&phy0>; - }; - port@1 { - reg = <1>; - label = "lan1"; - phy-handle = <&phy1>; - }; - port@2 { - reg = <2>; - label = "lan2"; - phy-handle = <&phy2>; - }; - port@3 { - reg = <3>; - label = "lan3"; - phy-handle = <&phy3>; - }; - port@4 { - reg = <4>; - label = "wan"; - phy-handle = <&phy4>; - }; - port@5 { - reg = <5>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "rgmii"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - mdio { - compatible = "realtek,smi-mdio", "dsa-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - phy0: phy@0 { - reg = <0>; - interrupt-parent = <&switch_intc>; - interrupts = <0>; - }; - phy1: phy@1 { - reg = <1>; - interrupt-parent = <&switch_intc>; - interrupts = <1>; - }; - phy2: phy@2 { - reg = <2>; - interrupt-parent = <&switch_intc>; - interrupts = <2>; - }; - phy3: phy@3 { - reg = <3>; - interrupt-parent = <&switch_intc>; - interrupts = <3>; - }; - phy4: phy@4 { - reg = <4>; - interrupt-parent = <&switch_intc>; - interrupts = <12>; - }; - }; -}; - -An example for the RTL8365MB-VC: - -switch { - compatible = "realtek,rtl8365mb"; - mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; - mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; - - switch_intc: interrupt-controller { - interrupt-parent = <&gpio5>; - interrupts = <1 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <1>; - }; - - ports { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - port@0 { - reg = <0>; - label = "swp0"; - phy-handle = <ðphy0>; - }; - port@1 { - reg = <1>; - label = "swp1"; - phy-handle = <ðphy1>; - }; - port@2 { - reg = <2>; - label = "swp2"; - phy-handle = <ðphy2>; - }; - port@3 { - reg = <3>; - label = "swp3"; - phy-handle = <ðphy3>; - }; - port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&fec1>; - phy-mode = "rgmii"; - tx-internal-delay-ps = <2000>; - rx-internal-delay-ps = <2000>; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - }; - - mdio { - compatible = "realtek,smi-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - ethphy0: phy@0 { - reg = <0>; - interrupt-parent = <&switch_intc>; - interrupts = <0>; - }; - ethphy1: phy@1 { - reg = <1>; - interrupt-parent = <&switch_intc>; - interrupts = <1>; - }; - ethphy2: phy@2 { - reg = <2>; - interrupt-parent = <&switch_intc>; - interrupts = <2>; - }; - ethphy3: phy@3 { - reg = <3>; - interrupt-parent = <&switch_intc>; - interrupts = <3>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/net/dsa/realtek.yaml b/Documentation/devicetree/bindings/net/dsa/realtek.yaml new file mode 100644 index 000000000000..1a7d45a8ad66 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/realtek.yaml @@ -0,0 +1,386 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/realtek.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Realtek switches for unmanaged switches + +allOf: + - $ref: dsa.yaml# + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: + Realtek advertises these chips as fast/gigabit switches or unmanaged + switches. They can be controlled using different interfaces, like SMI, + MDIO or SPI. + + The SMI "Simple Management Interface" is a two-wire protocol using + bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does + not use the MDIO protocol. This binding defines how to specify the + SMI-based Realtek devices. The realtek-smi driver is a platform driver + and it must be inserted inside a platform node. + + The MDIO-connected switches use MDIO protocol to access their registers. + The realtek-mdio driver is an MDIO driver and it must be inserted inside + an MDIO node. + + The compatible string is only used to identify which (silicon) family the + switch belongs to. Roughly speaking, a family is any set of Realtek switches + whose chip identification register(s) have a common location and semantics. + The different models in a given family can be automatically disambiguated by + parsing the chip identification register(s) according to the given family, + avoiding the need for a unique compatible string for each model. + +properties: + compatible: + enum: + - realtek,rtl8365mb + - realtek,rtl8366rb + description: | + realtek,rtl8365mb: + Use with models RTL8363NB, RTL8363NB-VB, RTL8363SC, RTL8363SC-VB, + RTL8364NB, RTL8364NB-VB, RTL8365MB, RTL8366SC, RTL8367RB-VB, RTL8367S, + RTL8367SB, RTL8370MB, RTL8310SR + realtek,rtl8366rb: + Use with models RTL8366RB, RTL8366S + + mdc-gpios: + description: GPIO line for the MDC clock line. + maxItems: 1 + + mdio-gpios: + description: GPIO line for the MDIO data line. + maxItems: 1 + + reset-gpios: + description: GPIO to be used to reset the whole device + maxItems: 1 + + realtek,disable-leds: + type: boolean + description: | + if the LED drivers are not used in the hardware design, + this will disable them so they are not turned on + and wasting power. + + interrupt-controller: + type: object + description: | + This defines an interrupt controller with an IRQ line (typically + a GPIO) that will demultiplex and handle the interrupt from the single + interrupt line coming out of one of the Realtek switch chips. It most + importantly provides link up/down interrupts to the PHY blocks inside + the ASIC. + + properties: + + interrupt-controller: true + + interrupts: + maxItems: 1 + description: + A single IRQ line from the switch, either active LOW or HIGH + + '#address-cells': + const: 0 + + '#interrupt-cells': + const: 1 + + required: + - interrupt-controller + - '#address-cells' + - '#interrupt-cells' + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + properties: + compatible: + const: realtek,smi-mdio + +if: + required: + - reg + +then: + $ref: /schemas/spi/spi-peripheral-props.yaml# + not: + required: + - mdc-gpios + - mdio-gpios + - mdio + + properties: + mdc-gpios: false + mdio-gpios: false + mdio: false + +else: + required: + - mdc-gpios + - mdio-gpios + - mdio + - reset-gpios + +required: + - compatible + + # - mdc-gpios + # - mdio-gpios + # - reset-gpios + # - mdio + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + platform { + switch { + compatible = "realtek,rtl8366rb"; + /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ + mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + + switch_intc1: interrupt-controller { + /* GPIO 15 provides the interrupt */ + interrupt-parent = <&gpio0>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&phy0>; + }; + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy1>; + }; + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy2>; + }; + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy3>; + }; + port@4 { + reg = <4>; + label = "wan"; + phy-handle = <&phy4>; + }; + port@5 { + reg = <5>; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc1>; + interrupts = <0>; + }; + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc1>; + interrupts = <1>; + }; + phy2: ethernet-phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc1>; + interrupts = <2>; + }; + phy3: ethernet-phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc1>; + interrupts = <3>; + }; + phy4: ethernet-phy@4 { + reg = <4>; + interrupt-parent = <&switch_intc1>; + interrupts = <12>; + }; + }; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + platform { + switch { + compatible = "realtek,rtl8365mb"; + mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + + switch_intc2: interrupt-controller { + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "swp0"; + phy-handle = <ðphy0>; + }; + port@1 { + reg = <1>; + label = "swp1"; + phy-handle = <ðphy1>; + }; + port@2 { + reg = <2>; + label = "swp2"; + phy-handle = <ðphy2>; + }; + port@3 { + reg = <3>; + label = "swp3"; + phy-handle = <ðphy3>; + }; + port@6 { + reg = <6>; + ethernet = <&fec1>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <2000>; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc2>; + interrupts = <0>; + }; + ethphy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc2>; + interrupts = <1>; + }; + ethphy2: ethernet-phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc2>; + interrupts = <2>; + }; + ethphy3: ethernet-phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc2>; + interrupts = <3>; + }; + }; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@29 { + compatible = "realtek,rtl8365mb"; + reg = <29>; + + reset-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>; + + switch_intc3: interrupt-controller { + interrupt-parent = <&gpio0>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan4"; + }; + + port@1 { + reg = <1>; + label = "lan3"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan1"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@7 { + reg = <7>; + ethernet = <ðernet>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml b/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml new file mode 100644 index 000000000000..7ca9c19a157c --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/renesas,rzn1-a5psw.yaml @@ -0,0 +1,158 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/renesas,rzn1-a5psw.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas RZ/N1 Advanced 5 ports ethernet switch + +maintainers: + - Clément Léger <clement.leger@bootlin.com> + +description: | + The advanced 5 ports switch is present on the Renesas RZ/N1 SoC family and + handles 4 ports + 1 CPU management port. + +allOf: + - $ref: dsa.yaml# + +properties: + compatible: + items: + - enum: + - renesas,r9a06g032-a5psw + - const: renesas,rzn1-a5psw + + reg: + maxItems: 1 + + interrupts: + items: + - description: Device Level Ring (DLR) interrupt + - description: Switch interrupt + - description: Parallel Redundancy Protocol (PRP) interrupt + - description: Integrated HUB module interrupt + - description: Receive Pattern Match interrupt + + interrupt-names: + items: + - const: dlr + - const: switch + - const: prp + - const: hub + - const: ptrn + + power-domains: + maxItems: 1 + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + clocks: + items: + - description: AHB clock used for the switch register interface + - description: Switch system clock + + clock-names: + items: + - const: hclk + - const: clk + + ethernet-ports: + type: object + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + patternProperties: + "^(ethernet-)?port@[0-4]$": + type: object + description: Ethernet switch ports + + properties: + pcs-handle: + description: + phandle pointing to a PCS sub-node compatible with + renesas,rzn1-miic.yaml# + $ref: /schemas/types.yaml#/definitions/phandle + +unevaluatedProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - power-domains + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/r9a06g032-sysctrl.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + switch@44050000 { + compatible = "renesas,r9a06g032-a5psw", "renesas,rzn1-a5psw"; + reg = <0x44050000 0x10000>; + clocks = <&sysctrl R9A06G032_HCLK_SWITCH>, <&sysctrl R9A06G032_CLK_SWITCH>; + clock-names = "hclk", "clk"; + power-domains = <&sysctrl>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "dlr", "switch", "prp", "hub", "ptrn"; + + dsa,member = <0 0>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&switch0phy3>; + pcs-handle = <&mii_conv4>; + }; + + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&switch0phy1>; + pcs-handle = <&mii_conv3>; + }; + + port@4 { + reg = <4>; + ethernet = <&gmac2>; + phy-mode = "internal"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&gpio0a 2 GPIO_ACTIVE_HIGH>; + reset-delay-us = <15>; + clock-frequency = <2500000>; + + switch0phy1: ethernet-phy@1{ + reg = <1>; + }; + + switch0phy3: ethernet-phy@3{ + reg = <3>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt index bbf4a13f6d75..258bef483673 100644 --- a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt +++ b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt @@ -75,7 +75,6 @@ switch@0 { }; vsc: port@6 { reg = <6>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "rgmii"; fixed-link { @@ -117,7 +116,6 @@ switch@2,0 { }; vsc: port@6 { reg = <6>; - label = "cpu"; ethernet = <&enet0>; phy-mode = "rgmii"; fixed-link { |