diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/xilinx_axienet.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/net/xilinx_axienet.txt | 37 |
1 files changed, 30 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt index 7360617cdedb..1aa4c6006cd0 100644 --- a/Documentation/devicetree/bindings/net/xilinx_axienet.txt +++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt @@ -26,7 +26,8 @@ Required properties: specified, the TX/RX DMA interrupts should be on that node instead, and only the Ethernet core interrupt is optionally specified here. -- phy-handle : Should point to the external phy device. +- phy-handle : Should point to the external phy device if exists. Pointing + this to the PCS/PMA PHY is deprecated and should be avoided. See ethernet.txt file in the same directory. - xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware @@ -38,11 +39,27 @@ Optional properties: 1 to enable partial TX checksum offload, 2 to enable full TX checksum offload - xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload -- clocks : AXI bus clock for the device. Refer to common clock bindings. - Used to calculate MDIO clock divisor. If not specified, it is - auto-detected from the CPU clock (but only on platforms where - this is possible). New device trees should specify this - the - auto detection is only for backward compatibility. +- xlnx,switch-x-sgmii : Boolean to indicate the Ethernet core is configured to + support both 1000BaseX and SGMII modes. If set, the phy-mode + should be set to match the mode selected on core reset (i.e. + by the basex_or_sgmii core input line). +- clock-names: Tuple listing input clock names. Possible clocks: + s_axi_lite_clk: Clock for AXI register slave interface + axis_clk: AXI4-Stream clock for TXD RXD TXC and RXS interfaces + ref_clk: Ethernet reference clock, used by signal delay + primitives and transceivers + mgt_clk: MGT reference clock (used by optional internal + PCS/PMA PHY) + + Note that if s_axi_lite_clk is not specified by name, the + first clock of any name is used for this. If that is also not + specified, the clock rate is auto-detected from the CPU clock + (but only on platforms where this is possible). New device + trees should specify all applicable clocks by name - the + fallbacks to an unnamed clock or to CPU clock are only for + backward compatibility. +- clocks: Phandles to input clocks matching clock-names. Refer to common + clock bindings. - axistream-connected: Reference to another node which contains the resources for the AXI DMA controller used by this device. If this is specified, the DMA-related resources from that @@ -52,13 +69,19 @@ Optional properties: required through the core's MDIO interface (i.e. always, unless the PHY is accessed through a different bus). + - pcs-handle: Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X + modes, where "pcs-handle" should be used to point + to the PCS/PMA PHY, and "phy-handle" should point to an + external PHY if exists. + Example: axi_ethernet_eth: ethernet@40c00000 { compatible = "xlnx,axi-ethernet-1.00.a"; device_type = "network"; interrupt-parent = <µblaze_0_axi_intc>; interrupts = <2 0 1>; - clocks = <&axi_clk>; + clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk"; + clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>; phy-mode = "mii"; reg = <0x40c00000 0x40000 0x50c00000 0x40000>; xlnx,rxcsum = <0x2>; |