diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl')
105 files changed, 5863 insertions, 1170 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml index 3f94f6944740..fb0f69ce9c16 100644 --- a/Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml @@ -184,6 +184,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml index cce63c3cc463..1e3c8de6cae1 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/pinctrl/allwinner,sun4i-a10-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Allwinner A10 Pin Controller Device Tree Bindings +title: Allwinner A10 Pin Controller maintainers: - Chen-Yu Tsai <wens@csie.org> @@ -46,6 +46,7 @@ properties: - allwinner,sun8i-v3s-pinctrl - allwinner,sun9i-a80-pinctrl - allwinner,sun9i-a80-r-pinctrl + - allwinner,sun20i-d1-pinctrl - allwinner,sun50i-a64-pinctrl - allwinner,sun50i-a64-r-pinctrl - allwinner,sun50i-a100-pinctrl @@ -80,9 +81,6 @@ properties: - const: hosc - const: losc - resets: - maxItems: 1 - gpio-controller: true interrupt-controller: true gpio-line-names: true @@ -127,26 +125,37 @@ patternProperties: additionalProperties: false - "^vcc-p[a-hlm]-supply$": + "^vcc-p[a-ilm]-supply$": description: Power supplies for pin banks. required: - "#gpio-cells" - - "#interrupt-cells" - compatible - reg - - interrupts - clocks - clock-names - gpio-controller - - interrupt-controller allOf: # FIXME: We should have the pin bank supplies here, but not a lot of # boards are defining it at the moment so it would generate a lot of # warnings. + - $ref: "pinctrl.yaml#" + - if: + not: + properties: + compatible: + enum: + - allwinner,sun50i-h616-r-pinctrl + + then: + required: + - "#interrupt-cells" + - interrupts + - interrupt-controller + - if: properties: compatible: @@ -174,6 +183,18 @@ allOf: properties: compatible: enum: + - allwinner,sun20i-d1-pinctrl + + then: + properties: + interrupts: + minItems: 6 + maxItems: 6 + + - if: + properties: + compatible: + enum: - allwinner,sun9i-a80-pinctrl then: diff --git a/Documentation/devicetree/bindings/pinctrl/apple,pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/apple,pinctrl.yaml index 572923d7023e..d3b11351ca45 100644 --- a/Documentation/devicetree/bindings/pinctrl/apple,pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/apple,pinctrl.yaml @@ -72,6 +72,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml index 100bb6dea3ec..f4f1ee6b116e 100644 --- a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml @@ -16,7 +16,7 @@ description: |+ - compatible: Should be one of the following: "aspeed,ast2400-scu", "syscon", "simple-mfd" - Refer to the the bindings described in + Refer to the bindings described in Documentation/devicetree/bindings/mfd/syscon.yaml properties: @@ -50,6 +50,9 @@ patternProperties: TXD3, TXD4, UART6, USB11D1, USB11H2, USB2D1, USB2H1, USBCKI, VGABIOS_ROM, VGAHS, VGAVS, VPI18, VPI24, VPI30, VPO12, VPO24, WDTRST1, WDTRST2] +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible @@ -60,6 +63,12 @@ examples: syscon: scu@1e6e2000 { compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; reg = <0x1e6e2000 0x1a8>; + #clock-cells = <1>; + #reset-cells = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1e6e2000 0x1000>; pinctrl: pinctrl { compatible = "aspeed,ast2400-pinctrl"; diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml index 904697bc9415..8168f0088471 100644 --- a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml @@ -17,7 +17,7 @@ description: |+ "aspeed,ast2500-scu", "syscon", "simple-mfd" "aspeed,g5-scu", "syscon", "simple-mfd" - Refer to the the bindings described in + Refer to the bindings described in Documentation/devicetree/bindings/mfd/syscon.yaml properties: @@ -29,6 +29,8 @@ properties: aspeed,external-nodes: minItems: 2 maxItems: 2 + items: + maxItems: 1 $ref: /schemas/types.yaml#/definitions/phandle-array description: | A cell of phandles to external controller nodes: @@ -62,6 +64,9 @@ patternProperties: USB11BHID, USB2AD, USB2AH, USB2BD, USB2BH, USBCKI, VGABIOSROM, VGAHS, VGAVS, VPI24, VPO, WDTRST1, WDTRST2] +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - aspeed,external-nodes @@ -70,58 +75,29 @@ additionalProperties: false examples: - | - apb { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - syscon: scu@1e6e2000 { - compatible = "aspeed,ast2500-scu", "syscon", "simple-mfd"; - reg = <0x1e6e2000 0x1a8>; - - pinctrl: pinctrl { - compatible = "aspeed,ast2500-pinctrl"; - aspeed,external-nodes = <&gfx>, <&lhc>; - - pinctrl_i2c3_default: i2c3_default { - function = "I2C3"; - groups = "I2C3"; - }; - - pinctrl_gpioh0_unbiased_default: gpioh0 { - pins = "A18"; - bias-disable; - }; - }; - }; - - gfx: display@1e6e6000 { - compatible = "aspeed,ast2500-gfx", "syscon"; - reg = <0x1e6e6000 0x1000>; - }; - }; - - lpc: lpc@1e789000 { - compatible = "aspeed,ast2500-lpc", "simple-mfd"; - reg = <0x1e789000 0x1000>; + #include <dt-bindings/clock/aspeed-clock.h> + scu@1e6e2000 { + compatible = "aspeed,ast2500-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + #clock-cells = <1>; + #reset-cells = <1>; #address-cells = <1>; #size-cells = <1>; - ranges = <0x0 0x1e789000 0x1000>; + ranges = <0x0 0x1e6e2000 0x1000>; - lpc_host: lpc-host@80 { - compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; - reg = <0x80 0x1e0>; - reg-io-width = <4>; + pinctrl: pinctrl { + compatible = "aspeed,ast2500-pinctrl"; + aspeed,external-nodes = <&gfx>, <&lhc>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x80 0x1e0>; + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; - lhc: lhc@20 { - compatible = "aspeed,ast2500-lhc"; - reg = <0x20 0x24>, <0x48 0x8>; + pinctrl_gpioh0_unbiased_default: gpioh0 { + pins = "A18"; + bias-disable; }; }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml index ad2866c99738..62424c42c981 100644 --- a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml @@ -16,7 +16,7 @@ description: |+ - compatible: Should be one of the following: "aspeed,ast2600-scu", "syscon", "simple-mfd" - Refer to the the bindings described in + Refer to the bindings described in Documentation/devicetree/bindings/mfd/syscon.yaml properties: @@ -33,7 +33,7 @@ patternProperties: $ref: "/schemas/types.yaml#/definitions/string" enum: [ ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15, ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, EMMC, ESPI, ESPIALT, - FSI1, FSI2, FWSPIABR, FWSPID, FWSPIWP, GPIT0, GPIT1, GPIT2, GPIT3, + FSI1, FSI2, FWQSPI, FWSPIABR, FWSPID, FWSPIWP, GPIT0, GPIT1, GPIT2, GPIT3, GPIT4, GPIT5, GPIT6, GPIT7, GPIU0, GPIU1, GPIU2, GPIU3, GPIU4, GPIU5, GPIU6, GPIU7, I2C1, I2C10, I2C11, I2C12, I2C13, I2C14, I2C15, I2C16, I2C2, I2C3, I2C4, I2C5, I2C6, I2C7, I2C8, I2C9, I3C3, I3C4, I3C5, @@ -58,7 +58,7 @@ patternProperties: $ref: "/schemas/types.yaml#/definitions/string" enum: [ ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15, ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, EMMCG1, EMMCG4, - EMMCG8, ESPI, ESPIALT, FSI1, FSI2, FWSPIABR, FWSPID, FWQSPID, FWSPIWP, + EMMCG8, ESPI, ESPIALT, FSI1, FSI2, FWQSPI, FWSPIABR, FWSPID, FWSPIWP, GPIT0, GPIT1, GPIT2, GPIT3, GPIT4, GPIT5, GPIT6, GPIT7, GPIU0, GPIU1, GPIU2, GPIU3, GPIU4, GPIU5, GPIU6, GPIU7, HVI3C3, HVI3C4, I2C1, I2C10, I2C11, I2C12, I2C13, I2C14, I2C15, I2C16, I2C2, I2C3, I2C4, I2C5, @@ -83,6 +83,9 @@ patternProperties: UART7, UART8, UART9, USBA, USBB, VB, VGAHS, VGAVS, WDTRST1, WDTRST2, WDTRST3, WDTRST4] +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible @@ -93,6 +96,12 @@ examples: syscon: scu@1e6e2000 { compatible = "aspeed,ast2600-scu", "syscon", "simple-mfd"; reg = <0x1e6e2000 0xf6c>; + #clock-cells = <1>; + #reset-cells = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1e6e2000 0x1000>; pinctrl: pinctrl { compatible = "aspeed,ast2600-pinctrl"; diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt index 4eaae32821ae..e047a198db38 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt @@ -85,7 +85,7 @@ Optional Properties (for I2C pins): - function: String. Specifies the pin mux selection. Values must be one of: "alt1", "alt2", "alt3", "alt4" - bias-pull-up: Integer. Pull up strength in Ohm. There are 3 - pull-up resisitors (1.2k, 1.8k, 2.7k) available + pull-up resistors (1.2k, 1.8k, 2.7k) available in parallel for I2C pins, so the valid values are: 568, 720, 831, 1080, 1200, 1800, 2700 Ohm. - bias-disable: No arguments. Disable pin bias. diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm4908-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm4908-pinctrl.yaml new file mode 100644 index 000000000000..8a9fb9b433ca --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm4908-pinctrl.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/brcm,bcm4908-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM4908 pin controller + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +description: + Binding for pin controller present on BCM4908 family SoCs. + +properties: + compatible: + const: brcm,bcm4908-pinctrl + + reg: + maxItems: 1 + +patternProperties: + '-pins$': + type: object + $ref: pinmux-node.yaml# + additionalProperties: false + + properties: + function: + enum: [ led_0, led_1, led_2, led_3, led_4, led_5, led_6, led_7, led_8, + led_9, led_10, led_11, led_12, led_13, led_14, led_15, led_16, + led_17, led_18, led_19, led_20, led_21, led_22, led_23, led_24, + led_25, led_26, led_27, led_28, led_29, led_30, led_31, + hs_uart, i2c, i2s, nand_ctrl, nand_data, emmc_ctrl, usb0_pwr, + usb1_pwr ] + + groups: + minItems: 1 + maxItems: 2 + items: + enum: [ led_0_grp_a, led_1_grp_a, led_2_grp_a, led_3_grp_a, + led_4_grp_a, led_5_grp_a, led_6_grp_a, led_7_grp_a, + led_8_grp_a, led_9_grp_a, led_10_grp_a, led_10_grp_b, + led_11_grp_a, led_11_grp_b, led_12_grp_a, led_12_grp_b, + led_13_grp_a, led_13_grp_b, led_14_grp_a, led_15_grp_a, + led_16_grp_a, led_17_grp_a, led_18_grp_a, led_19_grp_a, + led_20_grp_a, led_21_grp_a, led_22_grp_a, led_23_grp_a, + led_24_grp_a, led_25_grp_a, led_26_grp_a, led_27_grp_a, + led_28_grp_a, led_29_grp_a, led_30_grp_a, led_31_grp_a, + led_31_grp_b, hs_uart_grp, i2c_grp_a, i2c_grp_b, i2s_grp, + nand_ctrl_grp, nand_data_grp, emmc_ctrl_grp, usb0_pwr_grp, + usb1_pwr_grp ] + +allOf: + - $ref: pinctrl.yaml# + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + pinctrl@ff800560 { + compatible = "brcm,bcm4908-pinctrl"; + reg = <0xff800560 0x10>; + + led_0-a-pins { + function = "led_0"; + groups = "led_0_grp_a"; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6318-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6318-pinctrl.yaml index 08995a4f854b..ab019a1998e8 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6318-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6318-pinctrl.yaml @@ -37,6 +37,9 @@ patternProperties: enum: [ gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7, gpio8, gpio9, gpio10, gpio11, gpio12, gpio13, gpio40 ] +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm63268-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm63268-pinctrl.yaml index 58ffed44b3c4..8c9d4668c8c4 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm63268-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm63268-pinctrl.yaml @@ -41,6 +41,9 @@ patternProperties: vdsl_phy_override_1_grp, vdsl_phy_override_2_grp, vdsl_phy_override_3_grp, dsl_gpio8, dsl_gpio9 ] +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6328-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6328-pinctrl.yaml index 0fd24f40afb1..a8e22ec02215 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6328-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6328-pinctrl.yaml @@ -36,6 +36,9 @@ patternProperties: gpio20, gpio25, gpio26, gpio27, gpio28, hsspi_cs1, usb_port1 ] +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6358-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6358-pinctrl.yaml index 0c3ce256aa78..35867355a47a 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6358-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6358-pinctrl.yaml @@ -34,6 +34,9 @@ patternProperties: enum: [ ebi_cs_grp, uart1_grp, serial_led_grp, legacy_led_grp, led_grp, spi_cs_grp, utopia_grp, pwm_syn_clk, sys_irq_grp ] +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6362-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6362-pinctrl.yaml index 6f68fee373bd..b584d4b27223 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6362-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6362-pinctrl.yaml @@ -41,6 +41,9 @@ patternProperties: gpio15, gpio16, gpio17, gpio18, gpio19, gpio20, gpio21, gpio22, gpio23, gpio24, gpio25, gpio26, gpio27, nand_grp ] +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6368-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6368-pinctrl.yaml index f4168b9f4460..229323d9237d 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6368-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6368-pinctrl.yaml @@ -42,6 +42,9 @@ patternProperties: gpio24, gpio25, gpio26, gpio27, gpio28, gpio29, gpio30, gpio31, uart1_grp ] +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,ns-pinmux.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,ns-pinmux.yaml index fc39e3e9f71c..8d1e5b1cdd5f 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,ns-pinmux.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,ns-pinmux.yaml @@ -53,6 +53,7 @@ patternProperties: additionalProperties: false allOf: + - $ref: "pinctrl.yaml#" - if: properties: compatible: @@ -77,7 +78,7 @@ additionalProperties: false examples: - | - pin-controller@1800c1c0 { + pinctrl@1800c1c0 { compatible = "brcm,bcm4708-pinmux"; reg = <0x1800c1c0 0x24>; reg-names = "cru_gpio_control"; diff --git a/Documentation/devicetree/bindings/pinctrl/canaan,k210-fpioa.yaml b/Documentation/devicetree/bindings/pinctrl/canaan,k210-fpioa.yaml index 46fbc73ab26b..a78cb2796001 100644 --- a/Documentation/devicetree/bindings/pinctrl/canaan,k210-fpioa.yaml +++ b/Documentation/devicetree/bindings/pinctrl/canaan,k210-fpioa.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/pinctrl/canaan,k210-fpioa.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Canaan Kendryte K210 FPIOA Device Tree Bindings +title: Canaan Kendryte K210 FPIOA maintainers: - Damien Le Moal <damien.lemoal@wdc.com> @@ -39,6 +39,10 @@ properties: canaan,k210-sysctl-power: $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle of the K210 system controller node + - description: offset of its power domain control register description: | phandle of the K210 system controller node and offset of its power domain control register. @@ -116,6 +120,7 @@ patternProperties: input-schmitt-disable: true input-polarity-invert: + type: boolean description: Enable or disable pin input polarity inversion. @@ -128,6 +133,7 @@ patternProperties: output-low: true output-polarity-invert: + type: boolean description: Enable or disable pin output polarity inversion. @@ -137,6 +143,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg @@ -151,9 +160,9 @@ examples: #include <dt-bindings/clock/k210-clk.h> #include <dt-bindings/reset/k210-rst.h> - fpioa: pinmux@502B0000 { + fpioa: pinmux@502b0000 { compatible = "canaan,k210-fpioa"; - reg = <0x502B0000 0x100>; + reg = <0x502b0000 0x100>; clocks = <&sysclk K210_CLK_FPIOA>, <&sysclk K210_CLK_APB0>; clock-names = "ref", "pclk"; diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml b/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml index a07dd197176a..5cd512b7d5ba 100644 --- a/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml +++ b/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml @@ -51,15 +51,6 @@ properties: appropriate of the LOCHNAGARx_PIN_NUM_GPIOS define, see [3]. maxItems: 1 - pinctrl-0: - description: - A phandle to the default pinctrl state. - - pinctrl-names: - description: - A pinctrl state named "default" must be defined. - const: default - pin-settings: type: object patternProperties: @@ -181,6 +172,9 @@ properties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - gpio-controller diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml index 4cb174bf31ff..6bd42e43cdab 100644 --- a/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml +++ b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml @@ -30,16 +30,6 @@ description: | Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt properties: - pinctrl-0: - description: - A phandle to the node containing the subnodes containing default - configurations. - - pinctrl-names: - description: - A pinctrl state named "default" must be defined. - const: default - pin-settings: description: One subnode is required to contain the default settings. It @@ -58,13 +48,12 @@ properties: Name of one pin group to configure. enum: [ aif1, aif2, aif3, aif4, mif1, mif2, mif3, pdmspk1, pdmspk2, dmic4, dmic5, dmic6, gpio1, gpio2, gpio3, - gpio4, gpio5, gpio6, gpio7, gpio7, gpio8, gpio9, + gpio4, gpio5, gpio6, gpio7, gpio8, gpio9, gpio10, gpio11, gpio12, gpio13, gpio14, gpio15, - gpio16, gpio17, gpio17, gpio18, gpio19, gpio20, - gpio21, gpio22, gpio23, gpio24, gpio25, gpio26, - gpio27, gpio27, gpio28, gpio29, gpio30, gpio31, - gpio32, gpio33, gpio34, gpio35, gpio36, gpio37, - gpio37, gpio38, gpio39 ] + gpio16, gpio17, gpio18, gpio19, gpio20, gpio21, + gpio22, gpio23, gpio24, gpio25, gpio26, gpio27, + gpio28, gpio29, gpio30, gpio31, gpio32, gpio33, + gpio34, gpio35, gpio36, gpio37, gpio38, gpio39 ] function: description: diff --git a/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml b/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml new file mode 100644 index 000000000000..915cbbcc3555 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/cypress,cy8c95x0.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cypress CY8C95X0 I2C GPIO expander + +maintainers: + - Patrick Rudolph <patrick.rudolph@9elements.com> + +description: | + This supports the 20/40/60 pin Cypress CYC95x0 GPIO I2C expanders. + Pin function configuration is performed on a per-pin basis. + +properties: + compatible: + enum: + - cypress,cy8c9520 + - cypress,cy8c9540 + - cypress,cy8c9560 + + reg: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + description: + The first cell is the GPIO number and the second cell specifies GPIO + flags, as defined in <dt-bindings/gpio/gpio.h>. + const: 2 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + gpio-line-names: true + + gpio-ranges: + maxItems: 1 + + gpio-reserved-ranges: + maxItems: 1 + + vdd-supply: + description: + Optional power supply. + +patternProperties: + '-pins$': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: pincfg-node.yaml# + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + pattern: '^gp([0-7][0-7])$' + minItems: 1 + maxItems: 60 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + enum: [ gpio, pwm ] + + bias-pull-down: true + + bias-pull-up: true + + bias-disable: true + + output-high: true + + output-low: true + + drive-push-pull: true + + drive-open-drain: true + + drive-open-source: true + + required: + - pins + - function + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + +additionalProperties: false + +allOf: + - $ref: "pinctrl.yaml#" + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl@20 { + compatible = "cypress,cy8c9520"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + vdd-supply = <&p3v3>; + gpio-reserved-ranges = <5 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt deleted file mode 100644 index bfab5ca49fd1..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt +++ /dev/null @@ -1,87 +0,0 @@ -* Freescale i.MX7 Dual IOMUX Controller - -iMX7D supports two iomuxc controllers, fsl,imx7d-iomuxc controller is similar -as previous iMX SoC generation and fsl,imx7d-iomuxc-lpsr which provides low -power state retention capabilities on gpios that are part of iomuxc-lpsr -(GPIO1_IO7..GPIO1_IO0). While iomuxc-lpsr provides its own set of registers for -mux and pad control settings, it shares the input select register from main -iomuxc controller for daisy chain settings, the fsl,input-sel property extends -fsl,imx-pinctrl driver to support iomuxc-lpsr controller. - -iomuxc_lpsr: iomuxc-lpsr@302c0000 { - compatible = "fsl,imx7d-iomuxc-lpsr"; - reg = <0x302c0000 0x10000>; - fsl,input-sel = <&iomuxc>; -}; - -iomuxc: iomuxc@30330000 { - compatible = "fsl,imx7d-iomuxc"; - reg = <0x30330000 0x10000>; -}; - -Peripherals using pads from iomuxc-lpsr support low state retention power -state, under LPSR mode GPIO's state of pads are retain. - -Please refer to fsl,imx-pinctrl.txt in this directory for common binding part -and usage. - -Required properties: -- compatible: "fsl,imx7d-iomuxc" for main IOMUXC controller, or - "fsl,imx7d-iomuxc-lpsr" for Low Power State Retention IOMUXC controller. -- fsl,pins: each entry consists of 6 integers and represents the mux and config - setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val - input_val> are specified using a PIN_FUNC_ID macro, which can be found in - imx7d-pinfunc.h under device tree source folder. The last integer CONFIG is - the pad setting value like pull-up on this pin. Please refer to i.MX7 Dual - Reference Manual for detailed CONFIG settings. -- fsl,input-sel: required property for iomuxc-lpsr controller, this property is - a phandle for main iomuxc controller which shares the input select register for - daisy chain settings. - -CONFIG bits definition: -PAD_CTL_PUS_100K_DOWN (0 << 5) -PAD_CTL_PUS_5K_UP (1 << 5) -PAD_CTL_PUS_47K_UP (2 << 5) -PAD_CTL_PUS_100K_UP (3 << 5) -PAD_CTL_PUE (1 << 4) -PAD_CTL_HYS (1 << 3) -PAD_CTL_SRE_SLOW (1 << 2) -PAD_CTL_SRE_FAST (0 << 2) -PAD_CTL_DSE_X1 (0 << 0) -PAD_CTL_DSE_X4 (1 << 0) -PAD_CTL_DSE_X2 (2 << 0) -PAD_CTL_DSE_X6 (3 << 0) - -Examples: -While iomuxc-lpsr is intended to be used by dedicated peripherals to take -advantages of LPSR power mode, is also possible that an IP to use pads from -any of the iomux controllers. For example the I2C1 IP can use SCL pad from -iomuxc-lpsr controller and SDA pad from iomuxc controller as: - -i2c1: i2c@30a20000 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1_1>, <&pinctrl_i2c1_2>; -}; - -iomuxc-lpsr@302c0000 { - compatible = "fsl,imx7d-iomuxc-lpsr"; - reg = <0x302c0000 0x10000>; - fsl,input-sel = <&iomuxc>; - - pinctrl_i2c1_1: i2c1grp-1 { - fsl,pins = < - MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f - >; - }; -}; - -iomuxc@30330000 { - compatible = "fsl,imx7d-iomuxc"; - reg = <0x30330000 0x10000>; - - pinctrl_i2c1_2: i2c1grp-2 { - fsl,pins = < - MX7D_PAD_I2C1_SDA__I2C1_SDA 0x4000007f - >; - }; -}; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.yaml new file mode 100644 index 000000000000..621038662188 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/fsl,imx7d-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale IMX7D IOMUX Controller + +maintainers: + - Dong Aisheng <aisheng.dong@nxp.com> + +description: + Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory + for common binding part and usage. + +properties: + compatible: + oneOf: + - enum: + - fsl,imx7d-iomuxc + - fsl,imx7d-iomuxc-lpsr + + reg: + maxItems: 1 + + fsl,input-sel: + description: + phandle for main iomuxc controller which shares the input select + register for daisy chain settings. + $ref: /schemas/types.yaml#/definitions/phandle + +# Client device subnode's properties +patternProperties: + 'grp$': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + + properties: + fsl,pins: + description: + each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg + mux_val input_val> are specified using a PIN_FUNC_ID macro, which can + be found in <arch/arm/boot/dts/imx7d-pinfunc.h>. The last integer + CONFIG is the pad setting value like pull-up on this pin. Please + refer to i.MX7D Reference Manual for detailed CONFIG settings. + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + items: + - description: | + "mux_reg" indicates the offset of mux register. + - description: | + "conf_reg" indicates the offset of pad configuration register. + - description: | + "input_reg" indicates the offset of select input register. + - description: | + "mux_val" indicates the mux value to be applied. + - description: | + "input_val" indicates the select input value to be applied. + - description: | + "pad_setting" indicates the pad configuration value to be applied. + + required: + - fsl,pins + + additionalProperties: false + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + - reg + +if: + properties: + compatible: + contains: + enum: + - fsl,imx7d-iomuxc-lpsr + +then: + required: + - fsl,input-sel + +additionalProperties: false + +examples: + - | + iomuxc: pinctrl@30330000 { + compatible = "fsl,imx7d-iomuxc"; + reg = <0x30330000 0x10000>; + + pinctrl_uart5: uart5grp { + fsl,pins = + <0x0160 0x03D0 0x0714 0x1 0x0 0x7e>, + <0x0164 0x03D4 0x0000 0x1 0x0 0x76>; + }; + }; + - | + iomuxc_lpsr: pinctrl@302c0000 { + compatible = "fsl,imx7d-iomuxc-lpsr"; + reg = <0x302c0000 0x10000>; + fsl,input-sel = <&iomuxc>; + + pinctrl_gpio_lpsr: gpio1-grp { + fsl,pins = + <0x0008 0x0038 0x0000 0x0 0x0 0x59>, + <0x000C 0x003C 0x0000 0x0 0x0 0x59>; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml index 6d7d162e6171..6717f163390b 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.yaml @@ -58,6 +58,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mn-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mn-pinctrl.yaml index 7131cfd1fc45..b1cdbb56d4e4 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mn-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mn-pinctrl.yaml @@ -58,6 +58,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mp-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mp-pinctrl.yaml index d474bc1f393b..4eed3a4e153a 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mp-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mp-pinctrl.yaml @@ -58,6 +58,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mq-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mq-pinctrl.yaml index 0af2b6c95c17..d4a8ea5551a5 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mq-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mq-pinctrl.yaml @@ -58,6 +58,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8ulp-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx8ulp-pinctrl.yaml index 86622c4f374b..693398d88223 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx8ulp-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8ulp-pinctrl.yaml @@ -56,6 +56,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx93-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx93-pinctrl.yaml new file mode 100644 index 000000000000..66baa6082a4f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx93-pinctrl.yaml @@ -0,0 +1,85 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/fsl,imx93-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale IMX93 IOMUX Controller + +maintainers: + - Peng Fan <peng.fan@nxp.com> + +description: + Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory + for common binding part and usage. + +allOf: + - $ref: "pinctrl.yaml#" + +properties: + compatible: + const: fsl,imx93-iomuxc + + reg: + maxItems: 1 + +# Client device subnode's properties +patternProperties: + 'grp$': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + + properties: + fsl,pins: + description: + each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg + mux_val input_val> are specified using a PIN_FUNC_ID macro, which can + be found in <arch/arm64/boot/dts/freescale/imx8mp-pinfunc.h>. The last + integer CONFIG is the pad setting value like pull-up on this pin. Please + refer to i.MX8M Plus Reference Manual for detailed CONFIG settings. + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + items: + - description: | + "mux_reg" indicates the offset of mux register. + - description: | + "conf_reg" indicates the offset of pad configuration register. + - description: | + "input_reg" indicates the offset of select input register. + - description: | + "mux_val" indicates the mux value to be applied. + - description: | + "input_val" indicates the select input value to be applied. + - description: | + "pad_setting" indicates the pad configuration value to be applied. + + + required: + - fsl,pins + + additionalProperties: false + +required: + - compatible + - reg + +additionalProperties: false + +examples: + # Pinmux controller node + - | + iomuxc: pinctrl@443c0000 { + compatible = "fsl,imx93-iomuxc"; + reg = <0x30330000 0x10000>; + + pinctrl_uart3: uart3grp { + fsl,pins = + <0x48 0x1f8 0x41c 0x1 0x0 0x49>, + <0x4c 0x1fc 0x418 0x1 0x0 0x49>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imxrt1050.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imxrt1050.yaml new file mode 100644 index 000000000000..1278f7293560 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imxrt1050.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/fsl,imxrt1050.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale IMXRT1050 IOMUX Controller + +maintainers: + - Giulio Benetti <giulio.benetti@benettiengineering.com> + - Jesse Taube <Mr.Bossman075@gmail.com> + +description: + Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory + for common binding part and usage. + +properties: + compatible: + const: fsl,imxrt1050-iomuxc + + reg: + maxItems: 1 + +# Client device subnode's properties +patternProperties: + 'grp$': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + + properties: + fsl,pins: + description: + each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg + mux_val input_val> are specified using a PIN_FUNC_ID macro, which can + be found in <include/dt-bindings/pinctrl/pins-imxrt1050.h>. The last + integer CONFIG is the pad setting value like pull-up on this pin. Please + refer to i.MXRT1050 Reference Manual for detailed CONFIG settings. + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + items: + - description: | + "mux_reg" indicates the offset of mux register. + - description: | + "conf_reg" indicates the offset of pad configuration register. + - description: | + "input_reg" indicates the offset of select input register. + - description: | + "mux_val" indicates the mux value to be applied. + - description: | + "input_val" indicates the select input value to be applied. + - description: | + "pad_setting" indicates the pad configuration value to be applied. + + required: + - fsl,pins + + additionalProperties: false + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + iomuxc: iomuxc@401f8000 { + compatible = "fsl,imxrt1050-iomuxc"; + reg = <0x401f8000 0x4000>; + + pinctrl_lpuart1: lpuart1grp { + fsl,pins = + <0x0EC 0x2DC 0x000 0x2 0x0 0xf1>, + <0x0F0 0x2E0 0x000 0x2 0x0 0xf1>; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imxrt1170.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imxrt1170.yaml new file mode 100644 index 000000000000..2e880b3e537c --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imxrt1170.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/fsl,imxrt1170.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MXRT1170 IOMUX Controller + +maintainers: + - Giulio Benetti <giulio.benetti@benettiengineering.com> + - Jesse Taube <Mr.Bossman075@gmail.com> + +description: + Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory + for common binding part and usage. + +properties: + compatible: + const: fsl,imxrt1170-iomuxc + + reg: + maxItems: 1 + +# Client device subnode's properties +patternProperties: + 'grp$': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + + properties: + fsl,pins: + description: + each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg + mux_val input_val> are specified using a PIN_FUNC_ID macro, which can + be found in <arch/arm/boot/dts/imxrt1170-pinfunc.h>. The last + integer CONFIG is the pad setting value like pull-up on this pin. Please + refer to i.MXRT1170 Reference Manual for detailed CONFIG settings. + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + items: + - description: | + "mux_reg" indicates the offset of mux register. + - description: | + "conf_reg" indicates the offset of pad configuration register. + - description: | + "input_reg" indicates the offset of select input register. + - description: | + "mux_val" indicates the mux value to be applied. + - description: | + "input_val" indicates the select input value to be applied. + - description: | + "pad_setting" indicates the pad configuration value to be applied. + required: + - fsl,pins + + additionalProperties: false + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + iomuxc: iomuxc@400e8000 { + compatible = "fsl,imxrt1170-iomuxc"; + reg = <0x400e8000 0x4000>; + pinctrl_lpuart1: lpuart1grp { + fsl,pins = + <0x16C 0x3B0 0x620 0x0 0x0 0xf1>, + <0x170 0x3B4 0x61C 0x0 0x0 0xf1>; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,scu-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,scu-pinctrl.yaml new file mode 100644 index 000000000000..45ea565ce238 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,scu-pinctrl.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/fsl,scu-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: i.MX SCU Client Device Node - Pinctrl bindings based on SCU Message Protocol + +maintainers: + - Dong Aisheng <aisheng.dong@nxp.com> + +description: i.MX SCU Client Device Node + Client nodes are maintained as children of the relevant IMX-SCU device node. + This binding uses the i.MX common pinctrl binding. + (Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt) + +allOf: + - $ref: pinctrl.yaml# + +properties: + compatible: + enum: + - fsl,imx8qm-iomuxc + - fsl,imx8qxp-iomuxc + - fsl,imx8dxl-iomuxc + +patternProperties: + 'grp$': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + + properties: + fsl,pins: + description: + each entry consists of 3 integers and represents the pin ID, the mux value + and pad setting for the pin. The first 2 integers - pin_id and mux_val - are + specified using a PIN_FUNC_ID macro, which can be found in + <include/dt-bindings/pinctrl/pads-imx8qxp.h>. The last integer is + the pad setting value like pull-up on this pin. Please refer to the + appropriate i.MX8 Reference Manual for detailed pad CONFIG settings. + $ref: /schemas/types.yaml#/definitions/uint32-matrix + items: + items: + - description: | + "pin_id" indicates the pin ID + - description: | + "mux_val" indicates the mux value to be applied. + - description: | + "pad_setting" indicates the pad configuration value to be applied. + + required: + - fsl,pins + + additionalProperties: false + +required: + - compatible + +additionalProperties: false + +examples: + - | + pinctrl { + compatible = "fsl,imx8qxp-iomuxc"; + + pinctrl_lpuart0: lpuart0grp { + fsl,pins = < + 111 0 0x06000020 + 112 0 0x06000020 + >; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.yaml index a12d0ceb7637..c2c370448b81 100644 --- a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.yaml @@ -28,9 +28,6 @@ maintainers: - Paul Cercueil <paul@crapouillou.net> properties: - nodename: - pattern: "^pinctrl@[0-9a-f]+$" - compatible: oneOf: - enum: @@ -121,6 +118,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg @@ -169,7 +169,7 @@ additionalProperties: examples: - | - pin-controller@10010000 { + pinctrl@10010000 { compatible = "ingenic,jz4770-pinctrl"; reg = <0x10010000 0x600>; diff --git a/Documentation/devicetree/bindings/pinctrl/intel,lgm-io.yaml b/Documentation/devicetree/bindings/pinctrl/intel,lgm-io.yaml index 2c0acb405e6c..b42548350188 100644 --- a/Documentation/devicetree/bindings/pinctrl/intel,lgm-io.yaml +++ b/Documentation/devicetree/bindings/pinctrl/intel,lgm-io.yaml @@ -47,6 +47,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/intel,pinctrl-keembay.yaml b/Documentation/devicetree/bindings/pinctrl/intel,pinctrl-keembay.yaml index 5e99d79499b4..005d95a9e4d6 100644 --- a/Documentation/devicetree/bindings/pinctrl/intel,pinctrl-keembay.yaml +++ b/Documentation/devicetree/bindings/pinctrl/intel,pinctrl-keembay.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/pinctrl/intel,pinctrl-keembay.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Intel Keem Bay pin controller Device Tree Bindings +title: Intel Keem Bay pin controller maintainers: - Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com> @@ -44,6 +44,7 @@ properties: patternProperties: '^gpio@[0-9a-f]*$': type: object + additionalProperties: false description: Child nodes can be specified to contain pin configuration information, diff --git a/Documentation/devicetree/bindings/pinctrl/intel,pinctrl-thunderbay.yaml b/Documentation/devicetree/bindings/pinctrl/intel,pinctrl-thunderbay.yaml new file mode 100644 index 000000000000..f001add16814 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/intel,pinctrl-thunderbay.yaml @@ -0,0 +1,120 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/intel,pinctrl-thunderbay.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Intel Thunder Bay pin controller + +maintainers: + - Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com> + +description: | + Intel Thunder Bay SoC integrates a pin controller which enables control + of pin directions, input/output values and configuration + for a total of 67 pins. + +properties: + compatible: + const: intel,thunderbay-pinctrl + + reg: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + gpio-ranges: + maxItems: 1 + + interrupts: + description: + Specifies the interrupt lines to be used by the controller. + maxItems: 2 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + +patternProperties: + '^gpio@[0-9a-f]*$': + type: object + additionalProperties: false + + description: + Child nodes can be specified to contain pin configuration information, + which can then be utilized by pinctrl client devices. + The following properties are supported. + + properties: + pins: + description: | + The name(s) of the pins to be configured in the child node. + Supported pin names are "GPIO0" up to "GPIO66". + + bias-disable: true + + bias-pull-down: true + + bias-pull-up: true + + drive-strength: + description: Drive strength for the pad. + enum: [0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15] + + bias-bus-hold: + type: boolean + + input-schmitt-enable: + type: boolean + + slew-rate: + description: GPIO slew rate control. + 0 - Slow + 1 - Fast + enum: [0, 1] + +additionalProperties: false + +required: + - compatible + - reg + - gpio-controller + - '#gpio-cells' + - gpio-ranges + - interrupts + - interrupt-controller + - '#interrupt-cells' + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + // Example 1 + pinctrl0: gpio@0 { + compatible = "intel,thunderbay-pinctrl"; + reg = <0x600b0000 0x88>; + gpio-controller; + #gpio-cells = <0x2>; + gpio-ranges = <&pinctrl0 0 0 67>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + // Example 2 + pinctrl1: gpio@1 { + compatible = "intel,thunderbay-pinctrl"; + reg = <0x600c0000 0x88>; + gpio-controller; + #gpio-cells = <0x2>; + gpio-ranges = <&pinctrl1 0 0 53>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml new file mode 100644 index 000000000000..491f67e7cc4f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/marvell,ac5-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell AC5 pin controller + +maintainers: + - Chris Packham <chris.packham@alliedtelesis.co.nz> + +description: + Bindings for Marvell's AC5 memory-mapped pin controller. + +properties: + compatible: + items: + - const: marvell,ac5-pinctrl + + reg: + maxItems: 1 + +patternProperties: + '-pins$': + type: object + $ref: pinmux-node.yaml# + additionalProperties: false + + properties: + marvell,function: + $ref: "/schemas/types.yaml#/definitions/string" + description: + Indicates the function to select. + enum: [ dev_init_done, ge, gpio, i2c0, i2c1, int_out, led, nand, pcie, ptp, sdio, + spi0, spi1, synce, tsen_int, uart0, uart1, uart2, uart3, uartsd, wd_int, xg ] + + marvell,pins: + $ref: /schemas/types.yaml#/definitions/string-array + description: + Array of MPP pins to be used for the given function. + minItems: 1 + items: + enum: [ mpp0, mpp1, mpp2, mpp3, mpp4, mpp5, mpp6, mpp7, mpp8, mpp9, + mpp10, mpp11, mpp12, mpp13, mpp14, mpp15, mpp16, mpp17, mpp18, mpp19, + mpp20, mpp21, mpp22, mpp23, mpp24, mpp25, mpp26, mpp27, mpp28, mpp29, + mpp30, mpp31, mpp32, mpp33, mpp34, mpp35, mpp36, mpp37, mpp38, mpp39, + mpp40, mpp41, mpp42, mpp43, mpp44, mpp45 ] + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + pinctrl@80020100 { + compatible = "marvell,ac5-pinctrl"; + reg = <0x80020100 0x20>; + + i2c0_pins: i2c0-pins { + marvell,pins = "mpp26", "mpp27"; + marvell,function = "i2c0"; + }; + + i2c0_gpio: i2c0-gpio-pins { + marvell,pins = "mpp26", "mpp27"; + marvell,function = "gpio"; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt65xx-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt65xx-pinctrl.yaml index f8e6e138dc13..33b5f79e741a 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt65xx-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt65xx-pinctrl.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt65xx-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT65xx Pin Controller Device Tree Bindings +title: Mediatek MT65xx Pin Controller maintainers: - Sean Wang <sean.wang@kernel.org> @@ -44,6 +44,8 @@ properties: mediatek,pctl-regmap: $ref: /schemas/types.yaml#/definitions/phandle-array + items: + maxItems: 1 minItems: 1 maxItems: 2 description: | @@ -64,6 +66,9 @@ required: - gpio-controller - "#gpio-cells" +allOf: + - $ref: "pinctrl.yaml#" + patternProperties: '-[0-9]+$': type: object diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml index 152c151c27ad..8c79fcef7c52 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt6779-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT6779 Pin Controller Device Tree Bindings +title: Mediatek MT6779 Pin Controller maintainers: - Andy Teng <andy.teng@mediatek.com> @@ -59,6 +59,9 @@ properties: "#interrupt-cells": const: 2 +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg @@ -73,6 +76,8 @@ required: patternProperties: '-[0-9]*$': type: object + additionalProperties: false + patternProperties: '-pins*$': type: object diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6797-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6797-pinctrl.yaml index 76a6df75ed9c..637a8386e23e 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6797-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6797-pinctrl.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt6797-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT6797 Pin Controller Device Tree Bindings +title: Mediatek MT6797 Pin Controller maintainers: - Sean Wang <sean.wang@kernel.org> @@ -45,6 +45,9 @@ properties: "#interrupt-cells": const: 2 +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7622-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7622-pinctrl.yaml index 0feecd376c69..c9ea0cad489b 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7622-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7622-pinctrl.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt7622-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT7622 Pin Controller Device Tree Bindings +title: Mediatek MT7622 Pin Controller maintainers: - Sean Wang <sean.wang@kernel.org> @@ -42,6 +42,9 @@ properties: "#interrupt-cells": const: 2 +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml index 7602b11e8bce..89b8f3dd67a1 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt7986-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT7986 Pin Controller Device Tree Bindings +title: Mediatek MT7986 Pin Controller maintainers: - Sean Wang <sean.wang@kernel.org> @@ -56,6 +56,9 @@ properties: "#interrupt-cells": const: 2 +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg @@ -114,6 +117,10 @@ patternProperties: "i2s" "audio" 62, 63, 64, 65 "switch_int" "eth" 66 "mdc_mdio" "eth" 67 + "wf_2g" "wifi" 74, 75, 76, 77, 78, 79, 80, 81, 82, 83 + "wf_5g" "wifi" 91, 92, 93, 94, 95, 96, 97, 98, 99, 100 + "wf_dbdc" "wifi" 74, 75, 76, 77, 78, 79, 80, 81, 82, 83, + 84, 85 $ref: "/schemas/pinctrl/pinmux-node.yaml" properties: @@ -231,7 +238,9 @@ patternProperties: then: properties: groups: - enum: [wf_2g, wf_5g, wf_dbdc] + items: + enum: [wf_2g, wf_5g, wf_dbdc] + maxItems: 3 '.*conf.*': type: object additionalProperties: false @@ -245,25 +254,27 @@ patternProperties: An array of strings. Each string contains the name of a pin. There is no PIN 41 to PIN 65 above on mt7686b, you can only use those pins on mt7986a. - enum: [SYS_WATCHDOG, WF2G_LED, WF5G_LED, I2C_SCL, I2C_SDA, GPIO_0, - GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5, GPIO_6, GPIO_7, - GPIO_8, GPIO_9, GPIO_10, GPIO_11, GPIO_12, GPIO_13, GPIO_14, - GPIO_15, PWM0, PWM1, SPI0_CLK, SPI0_MOSI, SPI0_MISO, SPI0_CS, - SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI, SPI1_MISO, SPI1_CS, - SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP, - UART0_RXD, UART0_TXD, PCIE_PERESET_N, UART1_RXD, UART1_TXD, - UART1_CTS, UART1_RTS, UART2_RXD, UART2_TXD, UART2_CTS, - UART2_RTS, EMMC_DATA_0, EMMC_DATA_1, EMMC_DATA_2, - EMMC_DATA_3, EMMC_DATA_4, EMMC_DATA_5, EMMC_DATA_6, - EMMC_DATA_7, EMMC_CMD, EMMC_CK, EMMC_DSL, EMMC_RSTB, PCM_DTX, - PCM_DRX, PCM_CLK, PCM_FS, MT7531_INT, SMI_MDC, SMI_MDIO, - WF0_DIG_RESETB, WF0_CBA_RESETB, WF0_XO_REQ, WF0_TOP_CLK, - WF0_TOP_DATA, WF0_HB1, WF0_HB2, WF0_HB3, WF0_HB4, WF0_HB0, - WF0_HB0_B, WF0_HB5, WF0_HB6, WF0_HB7, WF0_HB8, WF0_HB9, - WF0_HB10, WF1_DIG_RESETB, WF1_CBA_RESETB, WF1_XO_REQ, - WF1_TOP_CLK, WF1_TOP_DATA, WF1_HB1, WF1_HB2, WF1_HB3, - WF1_HB4, WF1_HB0, WF1_HB0_B, WF1_HB5, WF1_HB6, WF1_HB7, - WF1_HB8] + items: + enum: [SYS_WATCHDOG, WF2G_LED, WF5G_LED, I2C_SCL, I2C_SDA, GPIO_0, + GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5, GPIO_6, GPIO_7, + GPIO_8, GPIO_9, GPIO_10, GPIO_11, GPIO_12, GPIO_13, GPIO_14, + GPIO_15, PWM0, PWM1, SPI0_CLK, SPI0_MOSI, SPI0_MISO, SPI0_CS, + SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI, SPI1_MISO, SPI1_CS, + SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP, + UART0_RXD, UART0_TXD, PCIE_PERESET_N, UART1_RXD, UART1_TXD, + UART1_CTS, UART1_RTS, UART2_RXD, UART2_TXD, UART2_CTS, + UART2_RTS, EMMC_DATA_0, EMMC_DATA_1, EMMC_DATA_2, + EMMC_DATA_3, EMMC_DATA_4, EMMC_DATA_5, EMMC_DATA_6, + EMMC_DATA_7, EMMC_CMD, EMMC_CK, EMMC_DSL, EMMC_RSTB, PCM_DTX, + PCM_DRX, PCM_CLK, PCM_FS, MT7531_INT, SMI_MDC, SMI_MDIO, + WF0_DIG_RESETB, WF0_CBA_RESETB, WF0_XO_REQ, WF0_TOP_CLK, + WF0_TOP_DATA, WF0_HB1, WF0_HB2, WF0_HB3, WF0_HB4, WF0_HB0, + WF0_HB0_B, WF0_HB5, WF0_HB6, WF0_HB7, WF0_HB8, WF0_HB9, + WF0_HB10, WF1_DIG_RESETB, WF1_CBA_RESETB, WF1_XO_REQ, + WF1_TOP_CLK, WF1_TOP_DATA, WF1_HB1, WF1_HB2, WF1_HB3, + WF1_HB4, WF1_HB0, WF1_HB0_B, WF1_HB5, WF1_HB6, WF1_HB7, + WF1_HB8] + maxItems: 101 bias-disable: true diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8183-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8183-pinctrl.yaml index cc1509e9b981..0d2484056a0f 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8183-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8183-pinctrl.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt8183-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT8183 Pin Controller Device Tree Bindings +title: Mediatek MT8183 Pin Controller maintainers: - Sean Wang <sean.wang@kernel.org> @@ -56,6 +56,9 @@ properties: "#interrupt-cells": const: 2 +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8188-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8188-pinctrl.yaml new file mode 100644 index 000000000000..7e750f1e643d --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8188-pinctrl.yaml @@ -0,0 +1,226 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8188-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek MT8188 Pin Controller + +maintainers: + - Hui Liu <hui.liu@mediatek.com> + +description: | + The MediaTek's MT8188 Pin controller is used to control SoC pins. + +properties: + compatible: + const: mediatek,mt8188-pinctrl + + gpio-controller: true + + '#gpio-cells': + description: | + Number of cells in GPIO specifier, should be two. The first cell + is the pin number, the second cell is used to specify optional + parameters which are defined in <dt-bindings/gpio/gpio.h>. + const: 2 + + gpio-ranges: + maxItems: 1 + + gpio-line-names: true + + reg: + items: + - description: gpio registers base address + - description: rm group io configuration registers base address + - description: lt group io configuration registers base address + - description: lm group io configuration registers base address + - description: rt group io configuration registers base address + - description: eint registers base address + + reg-names: + items: + - const: iocfg0 + - const: iocfg_rm + - const: iocfg_lt + - const: iocfg_lm + - const: iocfg_rt + - const: eint + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + interrupts: + description: The interrupt outputs to sysirq. + maxItems: 1 + + mediatek,rsel-resistance-in-si-unit: + type: boolean + description: | + We provide two methods to select the resistance for I2C when pull up or pull down. + The first is by RSEL definition value, another one is by resistance value(ohm). + This flag is used to identify if the method is resistance(si unit) value. + +# PIN CONFIGURATION NODES +patternProperties: + '-pins$': + type: object + additionalProperties: false + + patternProperties: + '^pins': + type: object + $ref: "/schemas/pinctrl/pincfg-node.yaml" + additionalProperties: false + description: | + A pinctrl node should contain at least one subnode representing the + pinctrl groups available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to muxer + configuration, pullups, drive strength, input enable/disable and + input schmitt. + + properties: + pinmux: + description: | + Integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are + defined as macros in dt-bindings/pinctrl/mediatek,<soc>-pinfunc.h + directly. + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + + drive-strength-microamp: + enum: [125, 250, 500, 1000] + + bias-pull-down: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt8188 pull down PUPD/R0/R1 type define value. + - enum: [200, 201, 202, 203, 204, 205, 206, 207] + description: mt8188 pull down RSEL type define value. + - enum: [75000, 5000] + description: mt8188 pull down RSEL type si unit value(ohm). + description: | + For pull down type is normal, it doesn't need add RSEL & R1R0 define + and resistance value. + For pull down type is PUPD/R0/R1 type, it can add R1R0 define to + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11" + define in mt8188. + For pull down type is RSEL, it can add RSEL define & resistance value(ohm) + to set different resistance by identifying property "mediatek,rsel-resistance-in-si-unit". + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100" + & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" + define in mt8188. It can also support resistance value(ohm) "75000" & "5000" in mt8188. + + bias-pull-up: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt8188 pull up PUPD/R0/R1 type define value. + - enum: [200, 201, 202, 203, 204, 205, 206, 207] + description: mt8188 pull up RSEL type define value. + - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000] + description: mt8188 pull up RSEL type si unit value(ohm). + description: | + For pull up type is normal, it don't need add RSEL & R1R0 define + and resistance value. + For pull up type is PUPD/R0/R1 type, it can add R1R0 define to + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11" + define in mt8188. + For pull up type is RSEL, it can add RSEL define & resistance value(ohm) + to set different resistance by identifying property "mediatek,rsel-resistance-in-si-unit". + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100" + & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" + define in mt8188. It can also support resistance value(ohm) + "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & "75000" in mt8188. + + bias-disable: true + + output-high: true + + output-low: true + + input-enable: true + + input-disable: true + + input-schmitt-enable: true + + input-schmitt-disable: true + + required: + - pinmux + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/pinctrl/mediatek,mt8188-pinfunc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pio: pinctrl@10005000 { + compatible = "mediatek,mt8188-pinctrl"; + reg = <0x10005000 0x1000>, + <0x11c00000 0x1000>, + <0x11e10000 0x1000>, + <0x11e20000 0x1000>, + <0x11ea0000 0x1000>, + <0x1000b000 0x1000>; + reg-names = "iocfg0", "iocfg_rm", + "iocfg_lt", "iocfg_lm", "iocfg_rt", + "eint"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pio 0 0 176>; + interrupt-controller; + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH 0>; + #interrupt-cells = <2>; + + pio-pins { + pins { + pinmux = <PINMUX_GPIO0__FUNC_B_GPIO0>; + output-low; + }; + }; + + spi0-pins { + pins-spi { + pinmux = <PINMUX_GPIO75__FUNC_O_SPIM1_CSB>, + <PINMUX_GPIO76__FUNC_O_SPIM1_CLK>, + <PINMUX_GPIO77__FUNC_B0_SPIM1_MOSI>; + drive-strength = <6>; + }; + pins-spi-mi { + pinmux = <PINMUX_GPIO78__FUNC_B0_SPIM1_MISO>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + }; + + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO55__FUNC_B1_SCL0>, + <PINMUX_GPIO56__FUNC_B1_SDA0>; + bias-disable; + drive-strength-microamp = <1000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,pinctrl-mt6795.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,pinctrl-mt6795.yaml new file mode 100644 index 000000000000..73ae6e11410b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,pinctrl-mt6795.yaml @@ -0,0 +1,224 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/mediatek,pinctrl-mt6795.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT6795 Pin Controller + +maintainers: + - AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> + - Sean Wang <sean.wang@kernel.org> + +description: | + The Mediatek's Pin controller is used to control SoC pins. + +properties: + compatible: + const: mediatek,mt6795-pinctrl + + gpio-controller: true + + '#gpio-cells': + description: | + Number of cells in GPIO specifier. Since the generic GPIO binding is used, + the amount of cells must be specified as 2. See the below + mentioned gpio binding representation for description of particular cells. + const: 2 + + gpio-ranges: + description: GPIO valid number range. + maxItems: 1 + + reg: + description: + Physical address base for gpio base and eint registers. + minItems: 2 + + reg-names: + items: + - const: base + - const: eint + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + interrupts: + description: The interrupt outputs to sysirq. + maxItems: 1 + +# PIN CONFIGURATION NODES +patternProperties: + '-pins$': + type: object + additionalProperties: false + patternProperties: + '^pins': + type: object + additionalProperties: false + description: | + A pinctrl node should contain at least one subnodes representing the + pinctrl groups available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to muxer + configuration, pullups, drive strength, input enable/disable and + input schmitt. + An example of using macro: + pincontroller { + /* GPIO0 set as multifunction GPIO0 */ + gpio-pins { + pins { + pinmux = <PINMUX_GPIO0__FUNC_GPIO0>; + } + }; + /* GPIO45 set as multifunction SDA0 */ + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO45__FUNC_SDA0>; + } + }; + }; + $ref: "pinmux-node.yaml" + + properties: + pinmux: + description: | + Integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are + defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h + directly. + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + + bias-pull-down: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt6795 pull down PUPD/R0/R1 type define value. + description: | + For normal pull down type, it is not necessary to specify R1R0 + values; When pull down type is PUPD/R0/R1, adding R1R0 defines + will set different resistance values. + + bias-pull-up: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt6795 pull up PUPD/R0/R1 type define value. + description: | + For normal pull up type, it is not necessary to specify R1R0 + values; When pull up type is PUPD/R0/R1, adding R1R0 defines + will set different resistance values. + + bias-disable: true + + output-high: true + + output-low: true + + input-enable: true + + input-disable: true + + input-schmitt-enable: true + + input-schmitt-disable: true + + mediatek,pull-up-adv: + description: | + Pull up setings for 2 pull resistors, R0 and R1. User can + configure those special pins. Valid arguments are described as below: + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + + mediatek,pull-down-adv: + description: | + Pull down settings for 2 pull resistors, R0 and R1. User can + configure those special pins. Valid arguments are described as below: + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + + required: + - pinmux + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/pinctrl/mt6795-pinfunc.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + pio: pinctrl@10005000 { + compatible = "mediatek,mt6795-pinctrl"; + reg = <0 0x10005000 0 0x1000>, <0 0x1000b000 0 0x1000>; + reg-names = "base", "eint"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pio 0 0 196>; + interrupt-controller; + interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <2>; + + i2c0-pins { + pins-sda-scl { + pinmux = <PINMUX_GPIO45__FUNC_SDA0>, + <PINMUX_GPIO46__FUNC_SCL0>; + }; + }; + + mmc0-pins { + pins-cmd-dat { + pinmux = <PINMUX_GPIO154__FUNC_MSDC0_DAT0>, + <PINMUX_GPIO155__FUNC_MSDC0_DAT1>, + <PINMUX_GPIO156__FUNC_MSDC0_DAT2>, + <PINMUX_GPIO157__FUNC_MSDC0_DAT3>, + <PINMUX_GPIO158__FUNC_MSDC0_DAT4>, + <PINMUX_GPIO159__FUNC_MSDC0_DAT5>, + <PINMUX_GPIO160__FUNC_MSDC0_DAT6>, + <PINMUX_GPIO161__FUNC_MSDC0_DAT7>, + <PINMUX_GPIO162__FUNC_MSDC0_CMD>; + input-enable; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + + pins-clk { + pinmux = <PINMUX_GPIO163__FUNC_MSDC0_CLK>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-rst { + pinmux = <PINMUX_GPIO165__FUNC_MSDC0_RSTB>; + bias-pull-up = <MTK_PUPD_SET_R1R0_10>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index 0aff1f28495c..8146193bd8ac 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -16,6 +16,7 @@ Required properties for the root node: "amlogic,meson-g12a-periphs-pinctrl" "amlogic,meson-g12a-aobus-pinctrl" "amlogic,meson-a1-periphs-pinctrl" + "amlogic,meson-s4-periphs-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml index cb554084bdf1..0df4e114fdd6 100644 --- a/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml +++ b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml @@ -145,7 +145,7 @@ examples: clocks = <&sys_clk>; pinctrl-0 = <&sgpio2_pins>; pinctrl-names = "default"; - reg = <0x1101059c 0x100>; + reg = <0x1101059c 0x118>; microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>; bus-frequency = <25000000>; sgpio_in2: gpio@0 { diff --git a/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt deleted file mode 100644 index db99bd95d423..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt +++ /dev/null @@ -1,41 +0,0 @@ -Microsemi Ocelot pin controller Device Tree Bindings ----------------------------------------------------- - -Required properties: - - compatible : Should be "mscc,ocelot-pinctrl", - "mscc,jaguar2-pinctrl", "microchip,sparx5-pinctrl", - "mscc,luton-pinctrl" or "mscc,serval-pinctrl" - - reg : Address and length of the register set for the device - - gpio-controller : Indicates this device is a GPIO controller - - #gpio-cells : Must be 2. - The first cell is the pin number and the - second cell specifies GPIO flags, as defined in - <dt-bindings/gpio/gpio.h>. - - gpio-ranges : Range of pins managed by the GPIO controller. - - -The ocelot-pinctrl driver uses the generic pin multiplexing and generic pin -configuration documented in pinctrl-bindings.txt. - -The following generic properties are supported: - - function - - pins - -Example: - gpio: pinctrl@71070034 { - compatible = "mscc,ocelot-pinctrl"; - reg = <0x71070034 0x28>; - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&gpio 0 0 22>; - - uart_pins: uart-pins { - pins = "GPIO_6", "GPIO_7"; - function = "uart"; - }; - - uart2_pins: uart2-pins { - pins = "GPIO_12", "GPIO_13"; - function = "uart2"; - }; - }; diff --git a/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.yaml new file mode 100644 index 000000000000..98d547c34ef3 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.yaml @@ -0,0 +1,116 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/mscc,ocelot-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microsemi Ocelot pin controller + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + - Lars Povlsen <lars.povlsen@microchip.com> + +properties: + compatible: + enum: + - microchip,lan966x-pinctrl + - microchip,sparx5-pinctrl + - mscc,jaguar2-pinctrl + - mscc,luton-pinctrl + - mscc,ocelot-pinctrl + - mscc,serval-pinctrl + - mscc,servalt-pinctrl + + reg: + items: + - description: Base address + - description: Extended pin configuration registers + minItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + gpio-ranges: true + + interrupts: + maxItems: 1 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + resets: + maxItems: 1 + + reset-names: + description: Optional shared switch reset. + items: + - const: switch + +patternProperties: + '-pins$': + type: object + allOf: + - $ref: "pinmux-node.yaml" + - $ref: "pincfg-node.yaml" + + properties: + function: true + pins: true + output-high: true + output-low: true + drive-strength: true + + required: + - function + - pins + + additionalProperties: false + +required: + - compatible + - reg + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +allOf: + - $ref: "pinctrl.yaml#" + - if: + properties: + compatible: + contains: + enum: + - microchip,lan966x-pinctrl + - microchip,sparx5-pinctrl + then: + properties: + reg: + minItems: 2 + +additionalProperties: false + +examples: + - | + gpio: pinctrl@71070034 { + compatible = "mscc,ocelot-pinctrl"; + reg = <0x71070034 0x28>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&gpio 0 0 22>; + + uart_pins: uart-pins { + pins = "GPIO_6", "GPIO_7"; + function = "uart"; + }; + + uart2_pins: uart2-pins { + pins = "GPIO_12", "GPIO_13"; + function = "uart2"; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml new file mode 100644 index 000000000000..7b7f840ffc4c --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml @@ -0,0 +1,161 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/nuvoton,wpcm450-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Nuvoton WPCM450 pin control and GPIO + +maintainers: + - Jonathan Neuschäfer <j.neuschaefer@gmx.net> + +properties: + compatible: + const: nuvoton,wpcm450-pinctrl + + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +patternProperties: + # There are three kinds of subnodes: + # 1. a GPIO controller node for each GPIO bank + # 2. a pinmux node configures pin muxing for a group of pins (e.g. rmii2) + # 3. a pinconf node configures properties of a single pin + + "^gpio@[0-7]$": + type: object + additionalProperties: false + + description: + Eight GPIO banks (gpio@0 to gpio@7), that each contain between 14 and 18 + GPIOs. Some GPIOs support interrupts. + + properties: + reg: + minimum: 0 + maximum: 7 + + gpio-controller: true + + "#gpio-cells": + const: 2 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + interrupts: + maxItems: 3 + description: + The interrupts associated with this GPIO bank + + required: + - reg + - gpio-controller + - '#gpio-cells' + + "^mux-": + $ref: pinmux-node.yaml# + + properties: + groups: + description: + One or more groups of pins to mux to a certain function + items: + enum: [ smb3, smb4, smb5, scs1, scs2, scs3, smb0, smb1, smb2, bsp, + hsp1, hsp2, r1err, r1md, rmii2, r2err, r2md, kbcc, dvo, + clko, smi, uinc, gspi, mben, xcs2, xcs1, sdio, sspi, fi0, + fi1, fi2, fi3, fi4, fi5, fi6, fi7, fi8, fi9, fi10, fi11, + fi12, fi13, fi14, fi15, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, + pwm6, pwm7, hg0, hg1, hg2, hg3, hg4, hg5, hg6, hg7 ] + function: + description: + The function that a group of pins is muxed to + enum: [ smb3, smb4, smb5, scs1, scs2, scs3, smb0, smb1, smb2, bsp, + hsp1, hsp2, r1err, r1md, rmii2, r2err, r2md, kbcc, dvo0, + dvo1, dvo2, dvo3, dvo4, dvo5, dvo6, dvo7, clko, smi, uinc, + gspi, mben, xcs2, xcs1, sdio, sspi, fi0, fi1, fi2, fi3, fi4, + fi5, fi6, fi7, fi8, fi9, fi10, fi11, fi12, fi13, fi14, fi15, + pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, pwm6, pwm7, hg0, hg1, + hg2, hg3, hg4, hg5, hg6, hg7, gpio ] + + dependencies: + groups: [ function ] + function: [ groups ] + + additionalProperties: false + + "^cfg-": + $ref: pincfg-node.yaml# + + properties: + pins: + description: + A list of pins to configure in certain ways, such as enabling + debouncing + items: + pattern: "^gpio1?[0-9]{1,2}$" + + input-debounce: true + + additionalProperties: false + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + pinctrl: pinctrl@b8003000 { + compatible = "nuvoton,wpcm450-pinctrl"; + reg = <0xb8003000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + gpio0: gpio@0 { + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>, + <3 IRQ_TYPE_LEVEL_HIGH>, + <4 IRQ_TYPE_LEVEL_HIGH>; + }; + + mux-rmii2 { + groups = "rmii2"; + function = "rmii2"; + }; + + pinmux_uid: mux-uid { + groups = "gspi", "sspi"; + function = "gpio"; + }; + + pinctrl_uid: cfg-uid { + pins = "gpio14"; + input-debounce = <1>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uid>, <&pinmux_uid>; + + button-uid { + label = "UID"; + linux,code = <102>; + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt deleted file mode 100644 index e0e886b73527..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt +++ /dev/null @@ -1,59 +0,0 @@ -Device tree binding for NVIDIA Tegra DPAUX pad controller -======================================================== - -The Tegra Display Port Auxiliary (DPAUX) pad controller manages two pins -which can be assigned to either the DPAUX channel or to an I2C -controller. - -This document defines the device-specific binding for the DPAUX pad -controller. Refer to pinctrl-bindings.txt in this directory for generic -information about pin controller device tree bindings. Please refer to -the binding document ../display/tegra/nvidia,tegra20-host1x.txt for more -details on the DPAUX binding. - -Pin muxing: ------------ - -Child nodes contain the pinmux configurations following the conventions -from the pinctrl-bindings.txt document. - -Since only three configurations are possible, only three child nodes are -needed to describe the pin mux'ing options for the DPAUX pads. -Furthermore, given that the pad functions are only applicable to a -single set of pads, the child nodes only need to describe the pad group -the functions are being applied to rather than the individual pads. - -Required properties: -- groups: Must be "dpaux-io" -- function: Must be either "aux", "i2c" or "off". - -Example: --------- - - dpaux@545c0000 { - ... - - state_dpaux_aux: pinmux-aux { - groups = "dpaux-io"; - function = "aux"; - }; - - state_dpaux_i2c: pinmux-i2c { - groups = "dpaux-io"; - function = "i2c"; - }; - - state_dpaux_off: pinmux-off { - groups = "dpaux-io"; - function = "off"; - }; - }; - - ... - - i2c@7000d100 { - ... - pinctrl-0 = <&state_dpaux_i2c>; - pinctrl-1 = <&state_dpaux_off>; - pinctrl-names = "default", "idle"; - }; diff --git a/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml index 71ed0a9def84..f5a121311f61 100644 --- a/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml +++ b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml @@ -52,11 +52,19 @@ properties: hardware supporting it the pull strength in Ohm. drive-push-pull: - type: boolean + oneOf: + - type: boolean + - $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + deprecated: true description: drive actively high and low drive-open-drain: - type: boolean + oneOf: + - type: boolean + - $ref: /schemas/types.yaml#/definitions/uint32 + const: 1 # No known cases of 0 + deprecated: true description: drive with open drain drive-open-source: @@ -114,6 +122,9 @@ properties: description: enable output on a pin without actively driving it (such as enabling an output buffer) + output-impedance-ohms: + description: set the output impedance of a pin to at most X ohms + output-low: type: boolean description: set the pin to output mode with low level diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index 9dae60acf950..6904072d3944 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -97,47 +97,8 @@ For example: }; == Pin controller devices == -Required properties: See the pin controller driver specific documentation -Optional properties: -#pinctrl-cells: Number of pin control cells in addition to the index within the - pin controller device instance - -pinctrl-use-default: Boolean. Indicates that the OS can use the boot default - pin configuration. This allows using an OS that does not have a - driver for the pin controller. This property can be set either - globally for the pin controller or in child nodes for individual - pin group control. - -Pin controller devices should contain the pin configuration nodes that client -devices reference. - -For example: - - pincontroller { - ... /* Standard DT properties for the device itself elided */ - - state_0_node_a { - ... - }; - state_1_node_a { - ... - }; - state_1_node_b { - ... - }; - } - -The contents of each of those pin configuration child nodes is defined -entirely by the binding for the individual pin controller device. There -exists no common standard for this content. The pinctrl framework only -provides generic helper bindings that the pin controller driver can use. - -The pin configuration nodes need not be direct children of the pin controller -device; they may be grandchildren, for example. Whether this is legal, and -whether there is any interaction between the child and intermediate parent -nodes, is again defined entirely by the binding for the individual pin -controller device. +See pinctrl.yaml == Generic pin multiplexing node content == diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8186.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8186.yaml new file mode 100644 index 000000000000..26573a793b57 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8186.yaml @@ -0,0 +1,276 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/pinctrl-mt8186.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT8186 Pin Controller + +maintainers: + - Sean Wang <sean.wang@mediatek.com> + +description: | + The Mediatek's Pin controller is used to control SoC pins. + +properties: + compatible: + const: mediatek,mt8186-pinctrl + + gpio-controller: true + + '#gpio-cells': + description: | + Number of cells in GPIO specifier. Since the generic GPIO binding is used, + the amount of cells must be specified as 2. See the below + mentioned gpio binding representation for description of particular cells. + const: 2 + + gpio-ranges: + maxItems: 1 + + gpio-line-names: true + + reg: + description: | + Physical address base for gpio base registers. There are 8 different GPIO + physical address base in mt8186. + maxItems: 8 + + reg-names: + description: | + Gpio base register names. + items: + - const: iocfg0 + - const: iocfg_lt + - const: iocfg_lm + - const: iocfg_lb + - const: iocfg_bl + - const: iocfg_rb + - const: iocfg_rt + - const: eint + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + interrupts: + description: The interrupt outputs to sysirq + maxItems: 1 + + mediatek,rsel-resistance-in-si-unit: + type: boolean + description: | + Identifying i2c pins pull up/down type which is RSEL. It can support + RSEL define or si unit value(ohm) to set different resistance. + +# PIN CONFIGURATION NODES +patternProperties: + '-pins$': + type: object + additionalProperties: false + patternProperties: + '^pins': + type: object + additionalProperties: false + description: | + A pinctrl node should contain at least one subnodes representing the + pinctrl groups available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to muxer + configuration, pullups, drive strength, input enable/disable and + input schmitt. + An example of using macro: + pincontroller { + /* GPIO0 set as multifunction GPIO0 */ + gpio-pins { + pins { + pinmux = <PINMUX_GPIO0__FUNC_GPIO0>; + } + }; + /* GPIO128 set as multifunction SDA0 */ + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO128__FUNC_SDA0>; + } + }; + }; + $ref: "pinmux-node.yaml" + + properties: + pinmux: + description: | + Integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are + defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h + directly. + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + + drive-strength-microamp: + enum: [125, 250, 500, 1000] + + bias-pull-down: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt8186 pull down PUPD/R0/R1 type define value. + - enum: [200, 201, 202, 203] + description: mt8186 pull down RSEL type define value. + - enum: [75000, 5000] + description: mt8186 pull down RSEL type si unit value(ohm). + description: | + For pull down type is normal, it don't need add RSEL & R1R0 define + and resistance value. + For pull down type is PUPD/R0/R1 type, it can add R1R0 define to + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & + "MTK_PUPD_SET_R1R0_11" define in mt8186. + For pull down type is RSEL, it can add RSEL define & resistance + value(ohm) to set different resistance by identifying property + "mediatek,rsel-resistance-in-si-unit". + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" + define in mt8186. It can also support resistance value(ohm) + "75000" & "5000" in mt8186. + An example of using RSEL define: + pincontroller { + i2c0_pin { + pins { + pinmux = <PINMUX_GPIO128__FUNC_SDA0>; + bias-pull-down = <MTK_PULL_SET_RSEL_001>; + } + }; + }; + An example of using si unit resistance value(ohm): + &pio { + mediatek,rsel-resistance-in-si-unit; + } + pincontroller { + i2c0_pin { + pins { + pinmux = <PINMUX_GPIO128__FUNC_SDA0>; + bias-pull-down = <75000>; + } + }; + }; + + bias-pull-up: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt8186 pull up PUPD/R0/R1 type define value. + - enum: [200, 201, 202, 203] + description: mt8186 pull up RSEL type define value. + - enum: [1000, 5000, 10000, 75000] + description: mt8186 pull up RSEL type si unit value(ohm). + description: | + For pull up type is normal, it don't need add RSEL & R1R0 define + and resistance value. + For pull up type is PUPD/R0/R1 type, it can add R1R0 define to + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & + "MTK_PUPD_SET_R1R0_11" define in mt8186. + For pull up type is RSEL, it can add RSEL define & resistance + value(ohm) to set different resistance by identifying property + "mediatek,rsel-resistance-in-si-unit". + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" + define in mt8186. It can also support resistance value(ohm) + "1000" & "5000" & "10000" & "75000" in mt8186. + An example of using si unit resistance value(ohm): + &pio { + mediatek,rsel-resistance-in-si-unit; + } + pincontroller { + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO128__FUNC_SDA0>; + bias-pull-up = <1000>; + } + }; + }; + + bias-disable: true + + output-high: true + + output-low: true + + input-enable: true + + input-disable: true + + input-schmitt-enable: true + + input-schmitt-disable: true + + required: + - pinmux + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/pinctrl/mt8186-pinfunc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pio: pinctrl@10005000 { + compatible = "mediatek,mt8186-pinctrl"; + reg = <0x10005000 0x1000>, + <0x10002000 0x0200>, + <0x10002200 0x0200>, + <0x10002400 0x0200>, + <0x10002600 0x0200>, + <0x10002A00 0x0200>, + <0x10002c00 0x0200>, + <0x1000b000 0x1000>; + reg-names = "iocfg0", "iocfg_lt", "iocfg_lm", + "iocfg_lb", "iocfg_bl", "iocfg_rb", + "iocfg_rt", "eint"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pio 0 0 185>; + interrupt-controller; + interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH 0>; + #interrupt-cells = <2>; + + pio-pins { + pins { + pinmux = <PINMUX_GPIO0__FUNC_GPIO0>; + output-low; + }; + }; + + spi0-pins { + pins-spi { + pinmux = <PINMUX_GPIO0__FUNC_SPI0_CLK_B>, + <PINMUX_GPIO1__FUNC_SPI0_CSB_B>, + <PINMUX_GPIO2__FUNC_SPI0_MO_B>; + bias-disable; + }; + pins-spi-mi { + pinmux = <PINMUX_GPIO3__FUNC_SPI0_MI_B>; + bias-pull-down; + }; + }; + + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO127__FUNC_SCL0>, + <PINMUX_GPIO128__FUNC_SDA0>; + bias-pull-up = <MTK_PULL_SET_RSEL_001>; + drive-strength-microamp = <1000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8192.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8192.yaml index c4c071211611..e0e943e5b874 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8192.yaml +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8192.yaml @@ -29,6 +29,8 @@ properties: description: gpio valid number range. maxItems: 1 + gpio-line-names: true + reg: description: | Physical address base for gpio base registers. There are 11 GPIO @@ -51,62 +53,79 @@ properties: #PIN CONFIGURATION NODES patternProperties: - '^pins': + '-pins$': type: object - description: | - A pinctrl node should contain at least one subnodes representing the - pinctrl groups available on the machine. Each subnode will list the - pins it needs, and how they should be configured, with regard to muxer - configuration, pullups, drive strength, input enable/disable and - input schmitt. - An example of using macro: - pincontroller { - /* GPIO0 set as multifunction GPIO0 */ - state_0_node_a { - pinmux = <PINMUX_GPIO0__FUNC_GPIO0>; - }; - /* GPIO1 set as multifunction PWM */ - state_0_node_b { - pinmux = <PINMUX_GPIO1__FUNC_PWM_1>; - }; - }; - $ref: "pinmux-node.yaml" - - properties: - pinmux: + additionalProperties: false + patternProperties: + '^pins': + type: object description: | - Integer array, represents gpio pin number and mux setting. - Supported pin number and mux varies for different SoCs, and are defined - as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly. + A pinctrl node should contain at least one subnodes representing the + pinctrl groups available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to muxer + configuration, pullups, drive strength, input enable/disable and + input schmitt. + $ref: "pinmux-node.yaml" - drive-strength: - description: | - It can support some arguments, such as MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See - dt-bindings/pinctrl/mt65xx.h. It can only support 2/4/6/8/10/12/14/16mA in mt8192. - enum: [2, 4, 6, 8, 10, 12, 14, 16] + properties: + pinmux: + description: | + Integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are defined + as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly. - bias-pull-down: true + drive-strength: + description: | + It can support some arguments, such as MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See + dt-bindings/pinctrl/mt65xx.h. It can only support 2/4/6/8/10/12/14/16mA in mt8192. + enum: [2, 4, 6, 8, 10, 12, 14, 16] - bias-pull-up: true + drive-strength-microamp: + enum: [125, 250, 500, 1000] - bias-disable: true + bias-pull-down: + oneOf: + - type: boolean + description: normal pull down. + - enum: [100, 101, 102, 103] + description: PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0_ + defines in dt-bindings/pinctrl/mt65xx.h. + - enum: [200, 201, 202, 203] + description: RSEL pull down type. See MTK_PULL_SET_RSEL_ + defines in dt-bindings/pinctrl/mt65xx.h. - output-high: true + bias-pull-up: + oneOf: + - type: boolean + description: normal pull up. + - enum: [100, 101, 102, 103] + description: PUPD/R1/R0 pull up type. See MTK_PUPD_SET_R1R0_ + defines in dt-bindings/pinctrl/mt65xx.h. + - enum: [200, 201, 202, 203] + description: RSEL pull up type. See MTK_PULL_SET_RSEL_ + defines in dt-bindings/pinctrl/mt65xx.h. - output-low: true + bias-disable: true - input-enable: true + output-high: true - input-disable: true + output-low: true - input-schmitt-enable: true + input-enable: true - input-schmitt-disable: true + input-disable: true - required: - - pinmux + input-schmitt-enable: true - additionalProperties: false + input-schmitt-disable: true + + required: + - pinmux + + additionalProperties: false + +allOf: + - $ref: "pinctrl.yaml#" required: - compatible @@ -148,8 +167,17 @@ examples: interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH 0>; #interrupt-cells = <2>; - pins { - pinmux = <PINMUX_GPIO0__FUNC_GPIO0>; - output-low; + spi1-default-pins { + pins-cs-mosi-clk { + pinmux = <PINMUX_GPIO157__FUNC_SPI1_A_CSB>, + <PINMUX_GPIO159__FUNC_SPI1_A_MO>, + <PINMUX_GPIO156__FUNC_SPI1_A_CLK>; + bias-disable; + }; + + pins-miso { + pinmux = <PINMUX_GPIO158__FUNC_SPI1_A_MI>; + bias-pull-down; + }; }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml index 5e2bb2bf3a55..66fe17e9e4d3 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml @@ -29,6 +29,8 @@ properties: description: gpio valid number range. maxItems: 1 + gpio-line-names: true + reg: description: | Physical address base for gpio base registers. There are 8 GPIO @@ -49,143 +51,173 @@ properties: description: The interrupt outputs to sysirq. maxItems: 1 - mediatek,rsel_resistance_in_si_unit: + mediatek,rsel-resistance-in-si-unit: type: boolean description: | Identifying i2c pins pull up/down type which is RSEL. It can support RSEL define or si unit value(ohm) to set different resistance. -#PIN CONFIGURATION NODES +# PIN CONFIGURATION NODES patternProperties: '-pins$': type: object - description: | - A pinctrl node should contain at least one subnodes representing the - pinctrl groups available on the machine. Each subnode will list the - pins it needs, and how they should be configured, with regard to muxer - configuration, pullups, drive strength, input enable/disable and - input schmitt. - An example of using macro: - pincontroller { - /* GPIO0 set as multifunction GPIO0 */ - gpio_pin { - pinmux = <PINMUX_GPIO0__FUNC_GPIO0>; - }; - /* GPIO8 set as multifunction SDA0 */ - i2c0_pin { - pinmux = <PINMUX_GPIO8__FUNC_SDA0>; - }; - }; - $ref: "pinmux-node.yaml" - - properties: - pinmux: - description: | - Integer array, represents gpio pin number and mux setting. - Supported pin number and mux varies for different SoCs, and are defined - as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly. - - drive-strength: - enum: [2, 4, 6, 8, 10, 12, 14, 16] - - bias-pull-down: - description: | - For pull down type is normal, it don't need add RSEL & R1R0 define - and resistance value. - For pull down type is PUPD/R0/R1 type, it can add R1R0 define to - set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & - "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11" - define in mt8195. - For pull down type is RSEL, it can add RSEL define & resistance value(ohm) - to set different resistance by identifying property "mediatek,rsel_resistance_in_si_unit". - It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" - & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100" - & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" - define in mt8195. It can also support resistance value(ohm) "75000" & "5000" in mt8195. - oneOf: - - enum: [100, 101, 102, 103] - - description: mt8195 pull down PUPD/R0/R1 type define value. - - enum: [200, 201, 202, 203, 204, 205, 206, 207] - - description: mt8195 pull down RSEL type define value. - - enum: [75000, 5000] - - description: mt8195 pull down RSEL type si unit value(ohm). - - An example of using RSEL define: - pincontroller { - i2c0_pin { - pinmux = <PINMUX_GPIO8__FUNC_SDA0>; - bias-pull-down = <MTK_PULL_SET_RSEL_001>; - }; - }; - An example of using si unit resistance value(ohm): - &pio { - mediatek,rsel_resistance_in_si_unit; - } - pincontroller { - i2c0_pin { - pinmux = <PINMUX_GPIO8__FUNC_SDA0>; - bias-pull-down = <75000>; - }; - }; - - bias-pull-up: + additionalProperties: false + patternProperties: + '^pins': + type: object + additionalProperties: false description: | - For pull up type is normal, it don't need add RSEL & R1R0 define - and resistance value. - For pull up type is PUPD/R0/R1 type, it can add R1R0 define to - set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & - "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11" - define in mt8195. - For pull up type is RSEL, it can add RSEL define & resistance value(ohm) - to set different resistance by identifying property "mediatek,rsel_resistance_in_si_unit". - It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" - & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100" - & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" - define in mt8195. It can also support resistance value(ohm) - "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & "75000" in mt8195. - oneOf: - - enum: [100, 101, 102, 103] - - description: mt8195 pull up PUPD/R0/R1 type define value. - - enum: [200, 201, 202, 203, 204, 205, 206, 207] - - description: mt8195 pull up RSEL type define value. - - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000] - - description: mt8195 pull up RSEL type si unit value(ohm). - An example of using RSEL define: + A pinctrl node should contain at least one subnodes representing the + pinctrl groups available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to muxer + configuration, pullups, drive strength, input enable/disable and + input schmitt. + An example of using macro: pincontroller { - i2c0_pin { - pinmux = <PINMUX_GPIO8__FUNC_SDA0>; - bias-pull-up = <MTK_PULL_SET_RSEL_001>; + /* GPIO0 set as multifunction GPIO0 */ + gpio-pins { + pins { + pinmux = <PINMUX_GPIO0__FUNC_GPIO0>; + } }; - }; - An example of using si unit resistance value(ohm): - &pio { - mediatek,rsel_resistance_in_si_unit; - } - pincontroller { - i2c0_pin { - pinmux = <PINMUX_GPIO8__FUNC_SDA0>; - bias-pull-up = <1000>; + /* GPIO8 set as multifunction SDA0 */ + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO8__FUNC_SDA0>; + } }; }; - - bias-disable: true - - output-high: true - - output-low: true - - input-enable: true - - input-disable: true - - input-schmitt-enable: true - - input-schmitt-disable: true - - required: - - pinmux - - additionalProperties: false + $ref: "pinmux-node.yaml" + + properties: + pinmux: + description: | + Integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are + defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h + directly. + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + + drive-strength-microamp: + enum: [125, 250, 500, 1000] + + bias-pull-down: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt8195 pull down PUPD/R0/R1 type define value. + - enum: [200, 201, 202, 203, 204, 205, 206, 207] + description: mt8195 pull down RSEL type define value. + - enum: [75000, 5000] + description: mt8195 pull down RSEL type si unit value(ohm). + description: | + For pull down type is normal, it don't need add RSEL & R1R0 define + and resistance value. + For pull down type is PUPD/R0/R1 type, it can add R1R0 define to + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & + "MTK_PUPD_SET_R1R0_11" define in mt8195. + For pull down type is RSEL, it can add RSEL define & resistance + value(ohm) to set different resistance by identifying property + "mediatek,rsel-resistance-in-si-unit". + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" + & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" + & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" + define in mt8195. It can also support resistance value(ohm) + "75000" & "5000" in mt8195. + + An example of using RSEL define: + pincontroller { + i2c0_pin { + pins { + pinmux = <PINMUX_GPIO8__FUNC_SDA0>; + bias-pull-down = <MTK_PULL_SET_RSEL_001>; + } + }; + }; + An example of using si unit resistance value(ohm): + &pio { + mediatek,rsel-resistance-in-si-unit; + } + pincontroller { + i2c0_pin { + pins { + pinmux = <PINMUX_GPIO8__FUNC_SDA0>; + bias-pull-down = <75000>; + } + }; + }; + + bias-pull-up: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt8195 pull up PUPD/R0/R1 type define value. + - enum: [200, 201, 202, 203, 204, 205, 206, 207] + description: mt8195 pull up RSEL type define value. + - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000] + description: mt8195 pull up RSEL type si unit value(ohm). + description: | + For pull up type is normal, it don't need add RSEL & R1R0 define + and resistance value. + For pull up type is PUPD/R0/R1 type, it can add R1R0 define to + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & + "MTK_PUPD_SET_R1R0_11" define in mt8195. + For pull up type is RSEL, it can add RSEL define & resistance + value(ohm) to set different resistance by identifying property + "mediatek,rsel-resistance-in-si-unit". + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" + & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" + & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" + define in mt8195. It can also support resistance value(ohm) + "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & + "75000" in mt8195. + An example of using RSEL define: + pincontroller { + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO8__FUNC_SDA0>; + bias-pull-up = <MTK_PULL_SET_RSEL_001>; + } + }; + }; + An example of using si unit resistance value(ohm): + &pio { + mediatek,rsel-resistance-in-si-unit; + } + pincontroller { + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO8__FUNC_SDA0>; + bias-pull-up = <1000>; + } + }; + }; + + bias-disable: true + + output-high: true + + output-low: true + + input-enable: true + + input-disable: true + + input-schmitt-enable: true + + input-schmitt-disable: true + + required: + - pinmux + +allOf: + - $ref: "pinctrl.yaml#" required: - compatible @@ -201,30 +233,55 @@ additionalProperties: false examples: - | - #include <dt-bindings/pinctrl/mt8195-pinfunc.h> - #include <dt-bindings/interrupt-controller/arm-gic.h> - pio: pinctrl@10005000 { - compatible = "mediatek,mt8195-pinctrl"; - reg = <0x10005000 0x1000>, - <0x11d10000 0x1000>, - <0x11d30000 0x1000>, - <0x11d40000 0x1000>, - <0x11e20000 0x1000>, - <0x11eb0000 0x1000>, - <0x11f40000 0x1000>, - <0x1000b000 0x1000>; - reg-names = "iocfg0", "iocfg_bm", "iocfg_bl", - "iocfg_br", "iocfg_lm", "iocfg_rb", - "iocfg_tl", "eint"; - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pio 0 0 144>; - interrupt-controller; - interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH 0>; - #interrupt-cells = <2>; - - pio-pins { - pinmux = <PINMUX_GPIO0__FUNC_GPIO0>; - output-low; - }; - }; + #include <dt-bindings/pinctrl/mt8195-pinfunc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + # + pio: pinctrl@10005000 { + compatible = "mediatek,mt8195-pinctrl"; + reg = <0x10005000 0x1000>, + <0x11d10000 0x1000>, + <0x11d30000 0x1000>, + <0x11d40000 0x1000>, + <0x11e20000 0x1000>, + <0x11eb0000 0x1000>, + <0x11f40000 0x1000>, + <0x1000b000 0x1000>; + reg-names = "iocfg0", "iocfg_bm", "iocfg_bl", + "iocfg_br", "iocfg_lm", "iocfg_rb", + "iocfg_tl", "eint"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pio 0 0 144>; + interrupt-controller; + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH 0>; + #interrupt-cells = <2>; + + pio-pins { + pins { + pinmux = <PINMUX_GPIO0__FUNC_GPIO0>; + output-low; + }; + }; + + spi0-pins { + pins-spi { + pinmux = <PINMUX_GPIO132__FUNC_SPIM0_CSB>, + <PINMUX_GPIO134__FUNC_SPIM0_MO>, + <PINMUX_GPIO133__FUNC_SPIM0_CLK>; + bias-disable; + }; + pins-spi-mi { + pinmux = <PINMUX_GPIO135__FUNC_SPIM0_MI>; + bias-pull-down; + }; + }; + + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO8__FUNC_SDA0>, + <PINMUX_GPIO9__FUNC_SCL0>; + bias-disable; + drive-strength-microamp = <1000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-rk805.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-rk805.txt index cbcbd31e3ce8..939cb5b6ffea 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-rk805.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-rk805.txt @@ -27,7 +27,7 @@ Required properties: - pins: List of pins. Valid values of pins properties are: gpio0, gpio1. First 2 properties must be added in the RK805 PMIC node, documented in -Documentation/devicetree/bindings/mfd/rk808.txt +Documentation/devicetree/bindings/mfd/rockchip,rk808.yaml Optional properties: ------------------- diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl.yaml new file mode 100644 index 000000000000..d471563119a9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Pin controller device + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + - Rafał Miłecki <rafal@milecki.pl> + +description: | + Pin controller devices should contain the pin configuration nodes that client + devices reference. + + The contents of each of those pin configuration child nodes is defined + entirely by the binding for the individual pin controller device. There + exists no common standard for this content. The pinctrl framework only + provides generic helper bindings that the pin controller driver can use. + + The pin configuration nodes need not be direct children of the pin controller + device; they may be grandchildren, for example. Whether this is legal, and + whether there is any interaction between the child and intermediate parent + nodes, is again defined entirely by the binding for the individual pin + controller device. + +properties: + $nodename: + pattern: "^(pinctrl|pinmux)(@[0-9a-f]+)?$" + + "#pinctrl-cells": + description: > + Number of pin control cells in addition to the index within the pin + controller device instance. + + pinctrl-use-default: + type: boolean + description: > + Indicates that the OS can use the boot default pin configuration. This + allows using an OS that does not have a driver for the pin controller. + This property can be set either globally for the pin controller or in + child nodes for individual pin group control. + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml index c64c93206817..931e5c190ead 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml @@ -118,6 +118,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg @@ -141,7 +144,7 @@ examples: #interrupt-cells = <2>; gpio-controller; #gpio-cells = <2>; - gpio-ranges = <&tlmm 0 80>; + gpio-ranges = <&tlmm 0 0 80>; serial3-pinmux { pins = "gpio44", "gpio45"; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml index 3b02dc6626ed..f7bd4be1739e 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml @@ -14,6 +14,7 @@ description: | MDM9607 platform. allOf: + - $ref: "pinctrl.yaml#" - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# properties: diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml index 040d2ada3669..ab4a2b4cfda2 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml @@ -97,6 +97,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml new file mode 100644 index 000000000000..e03530091478 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml @@ -0,0 +1,152 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,msm8909-tlmm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. MSM8909 TLMM block + +maintainers: + - Stephan Gerhold <stephan@gerhold.net> + +description: | + This binding describes the Top Level Mode Multiplexer (TLMM) block found + in the MSM8909 platform. + +allOf: + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# + +properties: + compatible: + const: qcom,msm8909-tlmm + + reg: + maxItems: 1 + + interrupts: true + interrupt-controller: true + '#interrupt-cells': true + gpio-controller: true + gpio-reserved-ranges: true + '#gpio-cells': true + gpio-ranges: true + wakeup-parent: true + +required: + - compatible + - reg + +additionalProperties: false + +patternProperties: + '-state$': + oneOf: + - $ref: "#/$defs/qcom-msm8909-tlmm-state" + - patternProperties: + ".*": + $ref: "#/$defs/qcom-msm8909-tlmm-state" + +$defs: + qcom-msm8909-tlmm-state: + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-9][0-9]|10[0-9]|11[0-7])$" + - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, + sdc2_data, qdsd_clk, qdsd_cmd, qdsd_data0, qdsd_data1, + qdsd_data2, qdsd_data3 ] + minItems: 1 + maxItems: 16 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + enum: [ adsp_ext, atest_bbrx0, atest_bbrx1, atest_char, atest_char0, + atest_char1, atest_char2, atest_char3, atest_combodac, + atest_gpsadc0, atest_gpsadc1, atest_wlan0, atest_wlan1, + bimc_dte0, bimc_dte1, blsp_i2c1, blsp_i2c2, blsp_i2c3, + blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_spi1, blsp_spi1_cs1, + blsp_spi1_cs2, blsp_spi1_cs3, blsp_spi2, blsp_spi2_cs1, + blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3, blsp_spi3_cs1, + blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4, blsp_spi5, blsp_spi6, + blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2, cam_mclk, + cci_async, cci_timer0, cci_timer1, cci_timer2, cdc_pdm0, + dbg_out, dmic0_clk, dmic0_data, ebi0_wrcdc, ebi2_a, ebi2_lcd, + ext_lpass, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gcc_plltest, gpio, + gsm0_tx, ldo_en, ldo_update, m_voc, mdp_vsync, modem_tsync, + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, + pri_mi2s_data0_a, pri_mi2s_data0_b, pri_mi2s_data1_a, + pri_mi2s_data1_b, pri_mi2s_mclk_a, pri_mi2s_mclk_b, + pri_mi2s_sck_a, pri_mi2s_sck_b, pri_mi2s_ws_a, pri_mi2s_ws_b, + prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b, + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a, + pwr_nav_enabled_b, qdss_cti_trig_in_a0, qdss_cti_trig_in_a1, + qdss_cti_trig_in_b0, qdss_cti_trig_in_b1, qdss_cti_trig_out_a0, + qdss_cti_trig_out_a1, qdss_cti_trig_out_b0, + qdss_cti_trig_out_b1, qdss_traceclk_a, qdss_tracectl_a, + qdss_tracedata_a, qdss_tracedata_b, sd_write, sec_mi2s, + smb_int, ssbi0, ssbi1, uim1_clk, uim1_data, uim1_present, + uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset, + uim3_clk, uim3_data, uim3_present, uim3_reset, uim_batt, + wcss_bt, wcss_fm, wcss_wlan ] + + bias-disable: true + bias-pull-down: true + bias-pull-up: true + drive-strength: true + input-enable: true + output-high: true + output-low: true + + required: + - pins + - function + + additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pinctrl@1000000 { + compatible = "qcom,msm8909-tlmm"; + reg = <0x1000000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 117>; + interrupt-controller; + #interrupt-cells = <2>; + + gpio-wo-subnode-state { + pins = "gpio1"; + function = "gpio"; + }; + + uart-w-subnodes-state { + rx { + pins = "gpio4"; + function = "blsp_uart1"; + bias-pull-up; + }; + + tx { + pins = "gpio5"; + function = "blsp_uart1"; + bias-disable; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml index abe9f4c9b1e3..d4da558cde54 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml @@ -34,6 +34,8 @@ properties: gpio-controller: true + gpio-reserved-ranges: true + '#gpio-cells': description: Specifying the pin number and flags, as defined in include/dt-bindings/gpio/gpio.h @@ -133,6 +135,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml index 8952b4cc1262..29dd503f9522 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml @@ -17,22 +17,29 @@ properties: compatible: items: - enum: + - qcom,pm2250-gpio - qcom,pm660-gpio - qcom,pm660l-gpio + - qcom,pm6125-gpio - qcom,pm6150-gpio - qcom,pm6150l-gpio - qcom,pm6350-gpio + - qcom,pm7250b-gpio - qcom,pm7325-gpio - qcom,pm8005-gpio - qcom,pm8008-gpio - qcom,pm8018-gpio + - qcom,pm8019-gpio - qcom,pm8038-gpio - qcom,pm8058-gpio - qcom,pm8150-gpio - qcom,pm8150b-gpio + - qcom,pm8150l-gpio + - qcom,pm8226-gpio - qcom,pm8350-gpio - qcom,pm8350b-gpio - qcom,pm8350c-gpio + - qcom,pm8450-gpio - qcom,pm8916-gpio - qcom,pm8917-gpio - qcom,pm8921-gpio @@ -45,10 +52,13 @@ properties: - qcom,pmi8994-gpio - qcom,pmi8998-gpio - qcom,pmk8350-gpio + - qcom,pmm8155au-gpio + - qcom,pmp8074-gpio - qcom,pmr735a-gpio - qcom,pmr735b-gpio - qcom,pms405-gpio - qcom,pmx55-gpio + - qcom,pmx65-gpio - enum: - qcom,spmi-gpio @@ -67,6 +77,16 @@ properties: gpio-ranges: maxItems: 1 + gpio-line-names: + minItems: 2 + maxItems: 44 + + gpio-reserved-ranges: + minItems: 1 + # maxItems as half of total number of GPIOs, as there has to be at + # least one usable GPIO between each reserved range. + maxItems: 22 + '#gpio-cells': const: 2 description: @@ -83,13 +103,281 @@ required: - gpio-ranges - interrupt-controller +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8008-gpio + - qcom,pmi8950-gpio + then: + properties: + gpio-line-names: + minItems: 2 + maxItems: 2 + gpio-reserved-ranges: + maxItems: 1 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8005-gpio + - qcom,pm8450-gpio + - qcom,pm8916-gpio + - qcom,pmk8350-gpio + - qcom,pmr735a-gpio + - qcom,pmr735b-gpio + then: + properties: + gpio-line-names: + minItems: 4 + maxItems: 4 + gpio-reserved-ranges: + minItems: 1 + maxItems: 2 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8018-gpio + - qcom,pm8019-gpio + then: + properties: + gpio-line-names: + minItems: 6 + maxItems: 6 + gpio-reserved-ranges: + minItems: 1 + maxItems: 3 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8226-gpio + - qcom,pm8350b-gpio + - qcom,pm8950-gpio + then: + properties: + gpio-line-names: + minItems: 8 + maxItems: 8 + gpio-reserved-ranges: + minItems: 1 + maxItems: 4 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm6350-gpio + - qcom,pm8350c-gpio + then: + properties: + gpio-line-names: + minItems: 9 + maxItems: 9 + gpio-reserved-ranges: + minItems: 1 + maxItems: 5 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm2250-gpio + - qcom,pm6150-gpio + - qcom,pm7325-gpio + - qcom,pm8150-gpio + - qcom,pm8350-gpio + - qcom,pmc8180-gpio + - qcom,pmi8994-gpio + - qcom,pmm8155au-gpio + then: + properties: + gpio-line-names: + minItems: 10 + maxItems: 10 + gpio-reserved-ranges: + minItems: 1 + maxItems: 5 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pmx55-gpio + then: + properties: + gpio-line-names: + minItems: 11 + maxItems: 11 + gpio-reserved-ranges: + minItems: 1 + maxItems: 6 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm660l-gpio + - qcom,pm6150l-gpio + - qcom,pm7250b-gpio + - qcom,pm8038-gpio + - qcom,pm8150b-gpio + - qcom,pm8150l-gpio + - qcom,pmc8180c-gpio + - qcom,pmp8074-gpio + - qcom,pms405-gpio + then: + properties: + gpio-line-names: + minItems: 12 + maxItems: 12 + gpio-reserved-ranges: + minItems: 1 + maxItems: 6 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm660-gpio + then: + properties: + gpio-line-names: + minItems: 13 + maxItems: 13 + gpio-reserved-ranges: + minItems: 1 + maxItems: 7 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pmi8998-gpio + then: + properties: + gpio-line-names: + minItems: 14 + maxItems: 14 + gpio-reserved-ranges: + minItems: 1 + maxItems: 7 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pmx65-gpio + then: + properties: + gpio-line-names: + minItems: 16 + maxItems: 16 + gpio-reserved-ranges: + minItems: 1 + maxItems: 8 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8994-gpio + - qcom,pma8084-gpio + then: + properties: + gpio-line-names: + minItems: 22 + maxItems: 22 + gpio-reserved-ranges: + minItems: 1 + maxItems: 11 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8998-gpio + then: + properties: + gpio-line-names: + minItems: 26 + maxItems: 26 + gpio-reserved-ranges: + minItems: 1 + maxItems: 13 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8941-gpio + then: + properties: + gpio-line-names: + minItems: 36 + maxItems: 36 + gpio-reserved-ranges: + minItems: 1 + maxItems: 18 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8917-gpio + then: + properties: + gpio-line-names: + minItems: 38 + maxItems: 38 + gpio-reserved-ranges: + minItems: 1 + maxItems: 19 + + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8058-gpio + - qcom,pm8921-gpio + then: + properties: + gpio-line-names: + minItems: 44 + maxItems: 44 + gpio-reserved-ranges: + minItems: 1 + maxItems: 22 + patternProperties: '-state$': oneOf: - $ref: "#/$defs/qcom-pmic-gpio-state" - patternProperties: - ".*": + "(pinconf|-pins)$": $ref: "#/$defs/qcom-pmic-gpio-state" + additionalProperties: false $defs: qcom-pmic-gpio-state: @@ -102,9 +390,11 @@ $defs: description: List of gpio pins affected by the properties specified in this subnode. Valid pins are + - gpio1-gpio9 for pm6125 - gpio1-gpio10 for pm6150 - gpio1-gpio12 for pm6150l - gpio1-gpio9 for pm6350 + - gpio1-gpio12 for pm7250b - gpio1-gpio10 for pm7325 - gpio1-gpio4 for pm8005 - gpio1-gpio2 for pm8008 @@ -120,6 +410,7 @@ $defs: - gpio1-gpio10 for pm8350 - gpio1-gpio8 for pm8350b - gpio1-gpio9 for pm8350c + - gpio1-gpio4 for pm8450 - gpio1-gpio38 for pm8917 - gpio1-gpio44 for pm8921 - gpio1-gpio36 for pm8941 @@ -130,12 +421,15 @@ $defs: - gpio1-gpio2 for pmi8950 - gpio1-gpio10 for pmi8994 - gpio1-gpio4 for pmk8350 + - gpio1-gpio10 for pmm8155au + - gpio1-gpio12 for pmp8074 (holes on gpio1 and gpio12) - gpio1-gpio4 for pmr735a - gpio1-gpio4 for pmr735b - gpio1-gpio12 for pms405 (holes on gpio1, gpio9 and gpio10) - gpio1-gpio11 for pmx55 (holes on gpio3, gpio7, gpio10 and gpio11) + - gpio1-gpio16 for pmx65 items: pattern: "^gpio([0-9]+)$" @@ -170,6 +464,7 @@ $defs: bias-high-impedance: true input-enable: true + input-disable: true output-high: true output-low: true output-enable: true @@ -228,7 +523,7 @@ examples: #gpio-cells = <2>; pm8921_gpio_keys: gpio-keys-state { - volume-keys { + volume-keys-pins { pins = "gpio20", "gpio21"; function = "normal"; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml index 35c846f59979..df79274d0ec3 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml @@ -21,6 +21,7 @@ properties: - qcom,pm8019-mpp - qcom,pm8038-mpp - qcom,pm8058-mpp + - qcom,pm8226-mpp - qcom,pm8821-mpp - qcom,pm8841-mpp - qcom,pm8916-mpp diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml index 13f338619d77..3f4f1c0360b5 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml @@ -42,8 +42,7 @@ properties: gpio-ranges: maxItems: 1 - wakeup-parent: - maxItems: 1 + wakeup-parent: true #PIN CONFIGURATION NODES patternProperties: @@ -118,6 +117,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-lpass-lpi-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-lpass-lpi-pinctrl.yaml new file mode 100644 index 000000000000..624e14f00790 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-lpass-lpi-pinctrl.yaml @@ -0,0 +1,119 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,sc7280-lpass-lpi-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. Low Power Audio SubSystem (LPASS) + Low Power Island (LPI) TLMM block + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + +description: | + This binding describes the Top Level Mode Multiplexer block found in the + LPASS LPI IP on most Qualcomm SoCs + +properties: + compatible: + const: qcom,sc7280-lpass-lpi-pinctrl + + qcom,adsp-bypass-mode: + description: + Tells ADSP is in bypass mode. + type: boolean + + reg: + minItems: 2 + maxItems: 2 + + gpio-controller: true + + '#gpio-cells': + description: Specifying the pin number and flags, as defined in + include/dt-bindings/gpio/gpio.h + const: 2 + + gpio-ranges: + maxItems: 1 + +#PIN CONFIGURATION NODES +patternProperties: + '-pins$': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: "/schemas/pinctrl/pincfg-node.yaml" + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-9][0-9])$" + minItems: 1 + maxItems: 15 + + function: + enum: [ gpio, swr_tx_clk, qua_mi2s_sclk, swr_tx_data, qua_mi2s_ws, + qua_mi2s_data, swr_rx_clk, swr_rx_data, dmic1_clk, i2s1_clk, + dmic1_data, i2s1_ws, dmic2_clk, dmic2_data, i2s1_data, + i2s2_clk, wsa_swr_clk, i2s2_ws, wsa_swr_data, dmic3_clk, + dmic3_data, i2s2_data ] + description: + Specify the alternative function to be configured for the specified + pins. + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + default: 2 + description: + Selects the drive strength for the specified pins, in mA. + + slew-rate: + enum: [0, 1, 2, 3] + default: 0 + description: | + 0: No adjustments + 1: Higher Slew rate (faster edges) + 2: Lower Slew rate (slower edges) + 3: Reserved (No adjustments) + + bias-pull-down: true + + bias-pull-up: true + + bias-disable: true + + output-high: true + + output-low: true + + required: + - pins + - function + + additionalProperties: false + +required: + - compatible + - reg + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + lpass_tlmm: pinctrl@33c0000 { + compatible = "qcom,sc7280-lpass-lpi-pinctrl"; + reg = <0x33c0000 0x20000>, + <0x3550000 0x10000>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&lpass_tlmm 0 0 15>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml index 7d6a2ab10eec..ad3496784678 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml @@ -7,7 +7,7 @@ $schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm Technologies, Inc. SC7280 TLMM block maintainers: - - Rajendra Nayak <rnayak@codeaurora.org> + - Bjorn Andersson <andersson@kernel.org> description: | This binding describes the Top Level Mode Multiplexer block found in the @@ -42,8 +42,10 @@ properties: gpio-ranges: maxItems: 1 - wakeup-parent: - maxItems: 1 + gpio-line-names: + maxItems: 174 + + wakeup-parent: true #PIN CONFIGURATION NODES patternProperties: @@ -52,7 +54,6 @@ patternProperties: description: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. - $ref: "/schemas/pinctrl/pincfg-node.yaml" properties: pins: @@ -61,7 +62,7 @@ patternProperties: subnode. items: oneOf: - - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-4])$" + - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9]|18[0-2])$" - enum: [ sdc1_rclk, sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset ] minItems: 1 @@ -119,10 +120,22 @@ patternProperties: required: - pins - - function + + allOf: + - $ref: /schemas/pinctrl/pincfg-node.yaml + - if: + properties: + pins: + pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9]|18[0-2])$" + then: + required: + - function additionalProperties: false +allOf: + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# + required: - compatible - reg @@ -137,22 +150,22 @@ additionalProperties: false examples: - | - #include <dt-bindings/interrupt-controller/arm-gic.h> - tlmm: pinctrl@f000000 { - compatible = "qcom,sc7280-pinctrl"; - reg = <0xf000000 0x1000000>; - interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - gpio-ranges = <&tlmm 0 0 175>; - wakeup-parent = <&pdc>; - - qup_uart5_default: qup-uart5-pins { - pins = "gpio46", "gpio47"; - function = "qup13"; - drive-strength = <2>; - bias-disable; - }; + #include <dt-bindings/interrupt-controller/arm-gic.h> + tlmm: pinctrl@f000000 { + compatible = "qcom,sc7280-pinctrl"; + reg = <0xf000000 0x1000000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 175>; + wakeup-parent = <&pdc>; + + qup_uart5_default: qup-uart5-pins { + pins = "gpio46", "gpio47"; + function = "qup13"; + drive-strength = <2>; + bias-disable; }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc8180x-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc8180x-pinctrl.yaml index a82dab898395..b98eeba2c530 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sc8180x-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc8180x-pinctrl.yaml @@ -14,6 +14,7 @@ description: | SC8180X platform. allOf: + - $ref: "pinctrl.yaml#" - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# properties: @@ -50,8 +51,9 @@ patternProperties: oneOf: - $ref: "#/$defs/qcom-sc8180x-tlmm-state" - patternProperties: - ".*": + "-pins$": $ref: "#/$defs/qcom-sc8180x-tlmm-state" + additionalProperties: false '$defs': qcom-sc8180x-tlmm-state: @@ -59,7 +61,6 @@ patternProperties: description: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" properties: pins: @@ -110,43 +111,52 @@ patternProperties: required: - pins - - function + + allOf: + - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + - if: + properties: + pins: + pattern: "^gpio([0-9]|[1-9][0-9]|1[0-8][0-9])$" + then: + required: + - function additionalProperties: false examples: - | - #include <dt-bindings/interrupt-controller/arm-gic.h> - pinctrl@3100000 { - compatible = "qcom,sc8180x-tlmm"; - reg = <0x03100000 0x300000>, - <0x03500000 0x700000>, - <0x03d00000 0x300000>; - reg-names = "west", "east", "south"; - interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - gpio-ranges = <&tlmm 0 0 190>; - - gpio-wo-subnode-state { - pins = "gpio1"; - function = "gpio"; - }; - - uart-w-subnodes-state { - rx { - pins = "gpio4"; - function = "qup6"; - bias-pull-up; - }; - - tx { - pins = "gpio5"; - function = "qup6"; - bias-disable; - }; - }; + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl@3100000 { + compatible = "qcom,sc8180x-tlmm"; + reg = <0x03100000 0x300000>, + <0x03500000 0x700000>, + <0x03d00000 0x300000>; + reg-names = "west", "east", "south"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 190>; + + gpio-wo-subnode-state { + pins = "gpio1"; + function = "gpio"; + }; + + uart-w-subnodes-state { + rx-pins { + pins = "gpio4"; + function = "qup6"; + bias-pull-up; + }; + + tx-pins { + pins = "gpio5"; + function = "qup6"; + bias-disable; + }; }; + }; ... diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-lpass-lpi-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-lpass-lpi-pinctrl.yaml new file mode 100644 index 000000000000..1f468303bb08 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-lpass-lpi-pinctrl.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,sc8280xp-lpass-lpi-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. Low Power Audio SubSystem (LPASS) + Low Power Island (LPI) TLMM block + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + +description: | + This binding describes the Top Level Mode Multiplexer block found in the + LPASS LPI IP on most Qualcomm SoCs + +properties: + compatible: + const: qcom,sc8280xp-lpass-lpi-pinctrl + + reg: + items: + - description: LPASS LPI TLMM Control and Status registers + - description: LPASS LPI pins SLEW registers + + clocks: + items: + - description: LPASS Core voting clock + - description: LPASS Audio voting clock + + clock-names: + items: + - const: core + - const: audio + + gpio-controller: true + + '#gpio-cells': + description: Specifying the pin number and flags, as defined in + include/dt-bindings/gpio/gpio.h + const: 2 + + gpio-ranges: + maxItems: 1 + +#PIN CONFIGURATION NODES +patternProperties: + '-pins$': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: /schemas/pinctrl/pincfg-node.yaml + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + pattern: "^gpio([0-1]|1[0-8]])$" + + function: + enum: [ swr_tx_clk, swr_tx_data, swr_rx_clk, swr_rx_data, + dmic1_clk, dmic1_data, dmic2_clk, dmic2_data, dmic4_clk, + dmic4_data, i2s2_clk, i2s2_ws, dmic3_clk, dmic3_data, + qua_mi2s_sclk, qua_mi2s_ws, qua_mi2s_data, i2s1_clk, i2s1_ws, + i2s1_data, wsa_swr_clk, wsa_swr_data, wsa2_swr_clk, + wsa2_swr_data, i2s2_data, i2s3_clk, i2s3_ws, i2s3_data, + ext_mclk1_c, ext_mclk1_b, ext_mclk1_a ] + description: + Specify the alternative function to be configured for the specified + pins. + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + default: 2 + description: + Selects the drive strength for the specified pins, in mA. + + slew-rate: + enum: [0, 1, 2, 3] + default: 0 + description: | + 0: No adjustments + 1: Higher Slew rate (faster edges) + 2: Lower Slew rate (slower edges) + 3: Reserved (No adjustments) + + bias-pull-down: true + + bias-pull-up: true + + bias-disable: true + + output-high: true + + output-low: true + + required: + - pins + - function + + additionalProperties: false + +allOf: + - $ref: pinctrl.yaml# + +required: + - compatible + - reg + - clocks + - clock-names + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/sound/qcom,q6afe.h> + pinctrl@33c0000 { + compatible = "qcom,sc8280xp-lpass-lpi-pinctrl"; + reg = <0x33c0000 0x20000>, + <0x3550000 0x10000>; + clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + clock-names = "core", "audio"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&lpi_tlmm 0 0 18>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml new file mode 100644 index 000000000000..b9ab130cd558 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml @@ -0,0 +1,160 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,sc8280xp-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. SC8280XP TLMM block + +maintainers: + - Bjorn Andersson <bjorn.andersson@linaro.org> + +description: | + This binding describes the Top Level Mode Multiplexer block found in the + SC8280XP platform. + +allOf: + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# + +properties: + compatible: + const: qcom,sc8280xp-tlmm + + reg: + maxItems: 1 + + interrupts: true + interrupt-controller: true + '#interrupt-cells': true + gpio-controller: true + gpio-reserved-ranges: true + '#gpio-cells': true + gpio-ranges: true + wakeup-parent: true + +required: + - compatible + - reg + +additionalProperties: false + +patternProperties: + '-state$': + oneOf: + - $ref: "#/$defs/qcom-sc8280xp-tlmm-state" + - patternProperties: + "-pins$": + $ref: "#/$defs/qcom-sc8280xp-tlmm-state" + additionalProperties: false + +'$defs': + qcom-sc8280xp-tlmm-state: + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-1][0-9]|22[0-7])$" + - enum: [ sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset, ufs1_reset ] + minItems: 1 + maxItems: 16 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + + enum: [ atest_char, atest_usb, audio_ref, cam_mclk, cci_async, cci_i2c, + cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, + cci_timer5, cci_timer6, cci_timer7, cci_timer8, cci_timer9, + cmu_rng, cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist, + ddr_pxi0, ddr_pxi1, ddr_pxi2, ddr_pxi3, ddr_pxi4, ddr_pxi5, + ddr_pxi6, ddr_pxi7, dp2_hot, dp3_hot, edp0_lcd, edp1_lcd, + edp2_lcd, edp3_lcd, edp_hot, emac0_dll, emac0_mcg0, emac0_mcg1, + emac0_mcg2, emac0_mcg3, emac0_phy, emac0_ptp, emac1_dll0, + emac1_dll1, emac1_mcg0, emac1_mcg1, emac1_mcg2, emac1_mcg3, + emac1_phy, emac1_ptp, gcc_gp1, gcc_gp2, gcc_gp3, gcc_gp4, + gcc_gp5, gpio, hs1_mi2s, hs2_mi2s, hs3_mi2s, ibi_i3c, + jitter_bist, lpass_slimbus, mdp0_vsync0, mdp0_vsync1, + mdp0_vsync2, mdp0_vsync3, mdp0_vsync4, mdp0_vsync5, + mdp0_vsync6, mdp0_vsync7, mdp0_vsync8, mdp1_vsync0, + mdp1_vsync1, mdp1_vsync2, mdp1_vsync3, mdp1_vsync4, + mdp1_vsync5, mdp1_vsync6, mdp1_vsync7, mdp1_vsync8, mdp_vsync, + mi2s0_data0, mi2s0_data1, mi2s0_sck, mi2s0_ws, mi2s1_data0, + mi2s1_data1, mi2s1_sck, mi2s1_ws, mi2s2_data0, mi2s2_data1, + mi2s2_sck, mi2s2_ws, mi2s_mclk1, mi2s_mclk2, pcie2a_clkreq, + pcie2b_clkreq, pcie3a_clkreq, pcie3b_clkreq, pcie4_clkreq, + phase_flag, pll_bist, pll_clk, prng_rosc0, prng_rosc1, + prng_rosc2, prng_rosc3, qdss_cti, qdss_gpio, qspi, qspi_clk, + qspi_cs, qup0, qup1, qup2, qup3, qup4, qup5, qup6, qup7, qup8, + qup9, qup10, qup11, qup12, qup13, qup14, qup15, qup16, qup17, + qup18, qup19, qup20, qup21, qup22, qup23, rgmii_0, rgmii_1, + sd_write, sdc40, sdc42, sdc43, sdc4_clk, sdc4_cmd, tb_trig, + tgu, tsense_pwm1, tsense_pwm2, tsense_pwm3, tsense_pwm4, + usb0_dp, usb0_phy, usb0_sbrx, usb0_sbtx, usb0_usb4, usb1_dp, + usb1_phy, usb1_sbrx, usb1_sbtx, usb1_usb4, usb2phy_ac, + vsense_trigger ] + + bias-disable: true + bias-pull-down: true + bias-pull-up: true + drive-strength: true + input-enable: true + output-high: true + output-low: true + + required: + - pins + + allOf: + - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + - if: + properties: + pins: + pattern: "^gpio([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-1][0-9]|22[0-7])$" + then: + required: + - function + + additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl@f100000 { + compatible = "qcom,sc8280xp-tlmm"; + reg = <0x0f100000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 230>; + + gpio-wo-subnode-state { + pins = "gpio1"; + function = "gpio"; + }; + + uart-w-subnodes-state { + rx-pins { + pins = "gpio4"; + function = "qup14"; + bias-pull-up; + }; + + tx-pins { + pins = "gpio5"; + function = "qup14"; + bias-disable; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml index 112dd59ce7ed..a38090b14aab 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml @@ -118,6 +118,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml new file mode 100644 index 000000000000..cdfcf29dffee --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml @@ -0,0 +1,191 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,sdx65-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. SDX65 TLMM block + +maintainers: + - Vamsi krishna Lanka <quic_vamslank@quicinc.com> + +description: + This binding describes the Top Level Mode Multiplexer block found in the + SDX65 platform. + +properties: + compatible: + const: qcom,sdx65-tlmm + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + description: Specifies the PIN numbers and Flags, as defined in + include/dt-bindings/interrupt-controller/irq.h + const: 2 + + gpio-controller: true + + '#gpio-cells': + description: Specifying the pin number and flags, as defined in + include/dt-bindings/gpio/gpio.h + const: 2 + + gpio-ranges: + maxItems: 1 + + gpio-reserved-ranges: + maxItems: 1 + +#PIN CONFIGURATION NODES +patternProperties: + '-state$': + oneOf: + - $ref: "#/$defs/qcom-sdx65-tlmm-state" + - patternProperties: + ".*": + $ref: "#/$defs/qcom-sdx65-tlmm-state" +'$defs': + qcom-sdx65-tlmm-state: + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-9][0-9]|10[0-7])$" + - enum: [ ufs_reset, sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, sdc1_rclk ] + minItems: 1 + maxItems: 150 + + function: + description: + Specify the alternative function to be configured for the specified + pins. Functions are only valid for gpio pins. + enum: [ blsp_uart1, blsp_spi1, blsp_i2c1, blsp_uim1, atest_tsens, + bimc_dte1, dac_calib0, blsp_spi8, blsp_uart8, blsp_uim8, + qdss_cti_trig_out_b, bimc_dte0, dac_calib1, qdss_cti_trig_in_b, + dac_calib2, atest_tsens2, atest_usb1, blsp_spi10, blsp_uart10, + blsp_uim10, atest_bbrx1, atest_usb13, atest_bbrx0, atest_usb12, + mdp_vsync, edp_lcd, blsp_i2c10, atest_gpsadc1, atest_usb11, + atest_gpsadc0, edp_hot, atest_usb10, m_voc, dac_gpio, atest_char, + cam_mclk, pll_bypassnl, qdss_stm7, blsp_i2c8, qdss_tracedata_b, + pll_reset, qdss_stm6, qdss_stm5, qdss_stm4, atest_usb2, cci_i2c, + qdss_stm3, dac_calib3, atest_usb23, atest_char3, dac_calib4, + qdss_stm2, atest_usb22, atest_char2, qdss_stm1, dac_calib5, + atest_usb21, atest_char1, dbg_out, qdss_stm0, dac_calib6, + atest_usb20, atest_char0, dac_calib10, qdss_stm10, + qdss_cti_trig_in_a, cci_timer4, blsp_spi6, blsp_uart6, blsp_uim6, + blsp2_spi, qdss_stm9, qdss_cti_trig_out_a, dac_calib11, + qdss_stm8, cci_timer0, qdss_stm13, dac_calib7, cci_timer1, + qdss_stm12, dac_calib8, cci_timer2, blsp1_spi, qdss_stm11, + dac_calib9, cci_timer3, cci_async, dac_calib12, blsp_i2c6, + qdss_tracectl_a, dac_calib13, qdss_traceclk_a, dac_calib14, + dac_calib15, hdmi_rcv, dac_calib16, hdmi_cec, pwr_modem, + dac_calib17, hdmi_ddc, pwr_nav, dac_calib18, pwr_crypto, + dac_calib19, hdmi_hot, dac_calib20, dac_calib21, pci_e0, + dac_calib22, dac_calib23, dac_calib24, tsif1_sync, dac_calib25, + sd_write, tsif1_error, blsp_spi2, blsp_uart2, blsp_uim2, + qdss_cti, blsp_i2c2, blsp_spi3, blsp_uart3, blsp_uim3, blsp_i2c3, + uim3, blsp_spi9, blsp_uart9, blsp_uim9, blsp10_spi, blsp_i2c9, + blsp_spi7, blsp_uart7, blsp_uim7, qdss_tracedata_a, blsp_i2c7, + qua_mi2s, gcc_gp1_clk_a, ssc_irq, uim4, blsp_spi11, blsp_uart11, + blsp_uim11, gcc_gp2_clk_a, gcc_gp3_clk_a, blsp_i2c11, cri_trng0, + cri_trng1, cri_trng, qdss_stm18, pri_mi2s, qdss_stm17, blsp_spi4, + blsp_uart4, blsp_uim4, qdss_stm16, qdss_stm15, blsp_i2c4, + qdss_stm14, dac_calib26, spkr_i2s, audio_ref, lpass_slimbus, + isense_dbg, tsense_pwm1, tsense_pwm2, btfm_slimbus, ter_mi2s, + qdss_stm22, qdss_stm21, qdss_stm20, qdss_stm19, gcc_gp1_clk_b, + sec_mi2s, blsp_spi5, blsp_uart5, blsp_uim5, gcc_gp2_clk_b, + gcc_gp3_clk_b, blsp_i2c5, blsp_spi12, blsp_uart12, blsp_uim12, + qdss_stm25, qdss_stm31, blsp_i2c12, qdss_stm30, qdss_stm29, + tsif1_clk, qdss_stm28, tsif1_en, tsif1_data, sdc4_cmd, qdss_stm27, + qdss_traceclk_b, tsif2_error, sdc43, vfr_1, qdss_stm26, tsif2_clk, + sdc4_clk, qdss_stm24, tsif2_en, sdc42, qdss_stm23, qdss_tracectl_b, + sd_card, tsif2_data, sdc41, tsif2_sync, sdc40, mdp_vsync_p_b, + ldo_en, mdp_vsync_s_b, ldo_update, blsp11_uart_tx_b, blsp11_uart_rx_b, + blsp11_i2c_sda_b, prng_rosc, blsp11_i2c_scl_b, uim2, uim1, uim_batt, + pci_e2, pa_indicator, adsp_ext, ddr_bist, qdss_tracedata_11, + qdss_tracedata_12, modem_tsync, nav_dr, nav_pps, pci_e1, gsm_tx, + qspi_cs, ssbi2, ssbi1, mss_lte, qspi_clk, qspi0, qspi1, qspi2, qspi3, + gpio ] + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + default: 2 + description: + Selects the drive strength for the specified pins, in mA. + + bias-pull-down: true + + bias-pull-up: true + + bias-disable: true + + output-high: true + + output-low: true + + required: + - pins + - function + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + tlmm: pinctrl@f100000 { + compatible = "qcom,sdx65-tlmm"; + reg = <0x03000000 0xdc2000>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 109>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>; + + gpio-wo-subnode-state { + pins = "gpio1"; + function = "gpio"; + }; + + uart-w-subnodes-state { + rx { + pins = "gpio4"; + function = "blsp_uart1"; + bias-pull-up; + }; + + tx { + pins = "gpio5"; + function = "blsp_uart1"; + bias-disable; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm6115-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm6115-pinctrl.yaml index 8fc06f6a3ef4..e39fbb36d8c1 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm6115-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm6115-pinctrl.yaml @@ -49,8 +49,9 @@ properties: gpio-ranges: maxItems: 1 - wakeup-parent: - maxItems: 1 + gpio-reserved-ranges: true + + wakeup-parent: true #PIN CONFIGURATION NODES patternProperties: @@ -58,8 +59,9 @@ patternProperties: oneOf: - $ref: "#/$defs/qcom-sm6115-tlmm-state" - patternProperties: - ".*": + "-pins$": $ref: "#/$defs/qcom-sm6115-tlmm-state" + additionalProperties: false '$defs': qcom-sm6115-tlmm-state: @@ -67,7 +69,6 @@ patternProperties: description: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" properties: pins: @@ -119,8 +120,21 @@ patternProperties: required: - pins + allOf: + - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + - if: + properties: + pins: + pattern: "^gpio([0-9]|[1-9][0-9]|10[0-9]|11[0-2])$" + then: + required: + - function + additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg @@ -136,44 +150,44 @@ additionalProperties: false examples: - | - #include <dt-bindings/interrupt-controller/arm-gic.h> - tlmm: pinctrl@500000 { - compatible = "qcom,sm6115-tlmm"; - reg = <0x500000 0x400000>, - <0x900000 0x400000>, - <0xd00000 0x400000>; - reg-names = "west", "south", "east"; - interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - gpio-ranges = <&tlmm 0 0 114>; - - sdc2_on_state: sdc2-on-state { - clk { - pins = "sdc2_clk"; - bias-disable; - drive-strength = <16>; - }; - - cmd { - pins = "sdc2_cmd"; - bias-pull-up; - drive-strength = <10>; - }; - - data { - pins = "sdc2_data"; - bias-pull-up; - drive-strength = <10>; - }; - - sd-cd { - pins = "gpio88"; - function = "gpio"; - bias-pull-up; - drive-strength = <2>; - }; - }; + #include <dt-bindings/interrupt-controller/arm-gic.h> + tlmm: pinctrl@500000 { + compatible = "qcom,sm6115-tlmm"; + reg = <0x500000 0x400000>, + <0x900000 0x400000>, + <0xd00000 0x400000>; + reg-names = "west", "south", "east"; + interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 114>; + + sdc2_on_state: sdc2-on-state { + clk-pins { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd-pins { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + data-pins { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + + sd-cd-pins { + pins = "gpio88"; + function = "gpio"; + bias-pull-up; + drive-strength = <2>; + }; }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm6125-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm6125-pinctrl.yaml index 5f7adaa81f83..5cb8b272cb7d 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm6125-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm6125-pinctrl.yaml @@ -13,6 +13,7 @@ description: | in the SM6125 platform. allOf: + - $ref: "pinctrl.yaml#" - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# properties: @@ -50,8 +51,9 @@ patternProperties: oneOf: - $ref: "#/$defs/qcom-sm6125-tlmm-state" - patternProperties: - ".*": + "-pins$": $ref: "#/$defs/qcom-sm6125-tlmm-state" + additionalProperties: false $defs: qcom-sm6125-tlmm-state: @@ -59,7 +61,6 @@ $defs: description: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" properties: pins: @@ -110,23 +111,52 @@ $defs: required: - pins - - function + + allOf: + - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + - if: + properties: + pins: + pattern: "^gpio[0-9]|[1-9][0-9]|1[0-2][0-9]|13[0-2]$" + then: + required: + - function additionalProperties: false examples: - | - #include <dt-bindings/interrupt-controller/arm-gic.h> - pinctrl@500000 { - compatible = "qcom,sm6125-tlmm"; - reg = <0x00500000 0x400000>, - <0x00900000 0x400000>, - <0x00d00000 0x400000>; - reg-names = "west", "south", "east"; - interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - gpio-ranges = <&tlmm 0 0 134>; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl@500000 { + compatible = "qcom,sm6125-tlmm"; + reg = <0x00500000 0x400000>, + <0x00900000 0x400000>, + <0x00d00000 0x400000>; + reg-names = "west", "south", "east"; + interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + gpio-ranges = <&tlmm 0 0 134>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + + sdc2-off-state { + clk-pins { + pins = "sdc2_clk"; + drive-strength = <2>; + bias-disable; + }; + + cmd-pins { + pins = "sdc2_cmd"; + drive-strength = <2>; + bias-pull-up; + }; + + data-pins { + pins = "sdc2_data"; + drive-strength = <2>; + bias-pull-up; + }; }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm6350-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm6350-pinctrl.yaml index 554992a681f3..856b9c567ecb 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm6350-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm6350-pinctrl.yaml @@ -14,6 +14,7 @@ description: | in the SM6350 platform. allOf: + - $ref: "pinctrl.yaml#" - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# properties: @@ -43,8 +44,9 @@ patternProperties: oneOf: - $ref: "#/$defs/qcom-sm6350-tlmm-state" - patternProperties: - ".*": + "-pins$": $ref: "#/$defs/qcom-sm6350-tlmm-state" + additionalProperties: false $defs: qcom-sm6350-tlmm-state: @@ -52,7 +54,6 @@ $defs: description: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" properties: pins: @@ -109,40 +110,49 @@ $defs: required: - pins - - function + + allOf: + - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + - if: + properties: + pins: + pattern: "^gpio([0-9]|[1-9][0-9]|1[0-4][0-9]|15[0-7])$" + then: + required: + - function additionalProperties: false examples: - | - #include <dt-bindings/interrupt-controller/arm-gic.h> - pinctrl@f100000 { - compatible = "qcom,sm6350-tlmm"; - reg = <0x0f100000 0x300000>; - interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - gpio-ranges = <&tlmm 0 0 157>; - - gpio-wo-subnode-state { - pins = "gpio1"; - function = "gpio"; - }; - - uart-w-subnodes-state { - rx { - pins = "gpio25"; - function = "qup13_f2"; - bias-disable; - }; - - tx { - pins = "gpio26"; - function = "qup13_f2"; - bias-disable; - }; - }; + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl@f100000 { + compatible = "qcom,sm6350-tlmm"; + reg = <0x0f100000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 157>; + + gpio-wo-subnode-state { + pins = "gpio1"; + function = "gpio"; + }; + + uart-w-subnodes-state { + rx-pins { + pins = "gpio25"; + function = "qup13_f2"; + bias-disable; + }; + + tx-pins { + pins = "gpio26"; + function = "qup13_f2"; + bias-disable; + }; }; + }; ... diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm6375-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm6375-tlmm.yaml new file mode 100644 index 000000000000..025faf87d147 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm6375-tlmm.yaml @@ -0,0 +1,167 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,sm6375-tlmm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. SM6375 TLMM block + +maintainers: + - Konrad Dybcio <konrad.dybcio@somainline.org> + +description: | + This binding describes the Top Level Mode Multiplexer (TLMM) block found + in the SM6375 platform. + +allOf: + - $ref: "pinctrl.yaml#" + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# + +properties: + compatible: + const: qcom,sm6375-tlmm + + reg: + maxItems: 1 + + interrupts: true + interrupt-controller: true + '#interrupt-cells': true + gpio-controller: true + gpio-reserved-ranges: true + '#gpio-cells': true + gpio-ranges: true + wakeup-parent: true + +required: + - compatible + - reg + +additionalProperties: false + +patternProperties: + '-state$': + oneOf: + - $ref: "#/$defs/qcom-sm6375-tlmm-state" + - patternProperties: + "-pins$": + $ref: "#/$defs/qcom-sm6375-tlmm-state" + additionalProperties: false + +$defs: + qcom-sm6375-tlmm-state: + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-4][0-9]|15[0-6])$" + - enum: [ ufs_reset, sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, + sdc2_cmd, sdc2_data ] + minItems: 1 + maxItems: 36 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + + enum: [ adsp_ext, agera_pll, atest_char, atest_char0, atest_char1, + atest_char2, atest_char3, atest_tsens, atest_tsens2, + atest_usb1, atest_usb10, atest_usb11, atest_usb12, + atest_usb13, atest_usb2, atest_usb20, atest_usb21, + atest_usb22, atest_usb23, audio_ref, btfm_slimbus, cam_mclk, + cci_async, cci_i2c, cci_timer0, cci_timer1, cci_timer2, + cci_timer3, cci_timer4, cri_trng, dbg_out, ddr_bist, + ddr_pxi0, ddr_pxi1, ddr_pxi2, ddr_pxi3, dp_hot, edp_lcd, + gcc_gp1, gcc_gp2, gcc_gp3, gp_pdm0, gp_pdm1, gp_pdm2, gpio, + gps_tx, ibi_i3c, jitter_bist, ldo_en, ldo_update, lpass_ext, + m_voc, mclk, mdp_vsync, mdp_vsync0, mdp_vsync1, mdp_vsync2, + mdp_vsync3, mi2s_0, mi2s_1, mi2s_2, mss_lte, nav_gpio, + nav_pps, pa_indicator, phase_flag0, phase_flag1, phase_flag10, + phase_flag11, phase_flag12, phase_flag13, phase_flag14, + phase_flag15, phase_flag16, phase_flag17, phase_flag18, + phase_flag19, phase_flag2, phase_flag20, phase_flag21, + phase_flag22, phase_flag23, phase_flag24, phase_flag25, + phase_flag26, phase_flag27, phase_flag28, phase_flag29, + phase_flag3, phase_flag30, phase_flag31, phase_flag4, + phase_flag5, phase_flag6, phase_flag7, phase_flag8, + phase_flag9, pll_bist, pll_bypassnl, pll_clk, pll_reset, + prng_rosc0, prng_rosc1, prng_rosc2, prng_rosc3, qdss_cti, + qdss_gpio, qdss_gpio0, qdss_gpio1, qdss_gpio10, qdss_gpio11, + qdss_gpio12, qdss_gpio13, qdss_gpio14, qdss_gpio15, + qdss_gpio2, qdss_gpio3, qdss_gpio4, qdss_gpio5, qdss_gpio6, + qdss_gpio7, qdss_gpio8, qdss_gpio9, qlink0_enable, + qlink0_request, qlink0_wmss, qlink1_enable, qlink1_request, + qlink1_wmss, qup00, qup01, qup02, qup10, qup11_f1, qup11_f2, + qup12, qup13_f1, qup13_f2, qup14, sd_write, sdc1_tb, sdc2_tb, + sp_cmu, tgu_ch0, tgu_ch1, tgu_ch2, tgu_ch3, tsense_pwm1, + tsense_pwm2, uim1_clk, uim1_data, uim1_present, uim1_reset, + uim2_clk, uim2_data, uim2_present, uim2_reset, usb2phy_ac, + usb_phy, vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1, + wlan2_adc0, wlan2_adc1 ] + + + bias-disable: true + bias-pull-down: true + bias-pull-up: true + drive-strength: true + input-enable: true + output-high: true + output-low: true + + required: + - pins + + allOf: + - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + - if: + properties: + pins: + pattern: "^gpio([0-9]|[1-9][0-9]|1[0-4][0-9]|15[0-6])$" + then: + required: + - function + + additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl@500000 { + compatible = "qcom,sm6375-tlmm"; + reg = <0x00500000 0x800000>; + interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 157>; + + gpio-wo-subnode-state { + pins = "gpio1"; + function = "gpio"; + }; + + uart-w-subnodes-state { + rx-pins { + pins = "gpio18"; + function = "qup13_f2"; + bias-pull-up; + }; + + tx-pins { + pins = "gpio19"; + function = "qup13_f2"; + bias-disable; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,lpass-lpi-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-lpass-lpi-pinctrl.yaml index e47ebf934daf..06efb1382876 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,lpass-lpi-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-lpass-lpi-pinctrl.yaml @@ -1,7 +1,7 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: http://devicetree.org/schemas/pinctrl/qcom,lpass-lpi-pinctrl.yaml# +$id: http://devicetree.org/schemas/pinctrl/qcom,sm8250-lpass-lpi-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm Technologies, Inc. Low Power Audio SubSystem (LPASS) @@ -103,6 +103,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml index 8508c57522fd..c44d02d28bc9 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml @@ -49,8 +49,7 @@ properties: gpio-ranges: maxItems: 1 - wakeup-parent: - maxItems: 1 + wakeup-parent: true #PIN CONFIGURATION NODES patternProperties: @@ -111,10 +110,22 @@ patternProperties: required: - pins - - function + + allOf: + - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + - if: + properties: + pins: + pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$" + then: + required: + - function additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg @@ -130,18 +141,18 @@ additionalProperties: false examples: - | - #include <dt-bindings/interrupt-controller/arm-gic.h> - pinctrl@1f00000 { - compatible = "qcom,sm8250-pinctrl"; - reg = <0x0f100000 0x300000>, - <0x0f500000 0x300000>, - <0x0f900000 0x300000>; - reg-names = "west", "south", "north"; - interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - gpio-ranges = <&tlmm 0 0 180>; - wakeup-parent = <&pdc>; - }; + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl@1f00000 { + compatible = "qcom,sm8250-pinctrl"; + reg = <0x0f100000 0x300000>, + <0x0f500000 0x300000>, + <0x0f900000 0x300000>; + reg-names = "west", "south", "north"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 180>; + wakeup-parent = <&pdc>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8350-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8350-pinctrl.yaml index 4f2667ea2805..6ae5571f60da 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8350-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8350-pinctrl.yaml @@ -14,6 +14,7 @@ description: | in the SM8350 platform. allOf: + - $ref: "pinctrl.yaml#" - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# properties: @@ -43,8 +44,9 @@ patternProperties: oneOf: - $ref: "#/$defs/qcom-sm8350-tlmm-state" - patternProperties: - ".*": + "-pins$": $ref: "#/$defs/qcom-sm8350-tlmm-state" + additionalProperties: false $defs: qcom-sm8350-tlmm-state: @@ -52,7 +54,6 @@ $defs: description: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" properties: pins: @@ -106,40 +107,49 @@ $defs: required: - pins - - function + + allOf: + - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + - if: + properties: + pins: + pattern: "^gpio([0-9]|[1-9][0-9]|1[0-9][0-9]|20[0-3])$" + then: + required: + - function additionalProperties: false examples: - | - #include <dt-bindings/interrupt-controller/arm-gic.h> - pinctrl@f100000 { - compatible = "qcom,sm8350-tlmm"; - reg = <0x0f100000 0x300000>; - interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - gpio-ranges = <&tlmm 0 0 203>; - - gpio-wo-subnode-state { - pins = "gpio1"; - function = "gpio"; - }; - - uart-w-subnodes-state { - rx { - pins = "gpio18"; - function = "qup3"; - bias-pull-up; - }; - - tx { - pins = "gpio19"; - function = "qup3"; - bias-disable; - }; - }; + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl@f100000 { + compatible = "qcom,sm8350-tlmm"; + reg = <0x0f100000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 203>; + + gpio-wo-subnode-state { + pins = "gpio1"; + function = "gpio"; + }; + + uart-w-subnodes-state { + rx-pins { + pins = "gpio18"; + function = "qup3"; + bias-pull-up; + }; + + tx-pins { + pins = "gpio19"; + function = "qup3"; + bias-disable; + }; }; + }; ... diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-lpass-lpi-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-lpass-lpi-pinctrl.yaml new file mode 100644 index 000000000000..3694795ec793 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-lpass-lpi-pinctrl.yaml @@ -0,0 +1,135 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,sm8450-lpass-lpi-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. Low Power Audio SubSystem (LPASS) + Low Power Island (LPI) TLMM block + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + +description: | + This binding describes the Top Level Mode Multiplexer block found in the + LPASS LPI IP on most Qualcomm SoCs + +properties: + compatible: + const: qcom,sm8450-lpass-lpi-pinctrl + + reg: + items: + - description: LPASS LPI TLMM Control and Status registers + - description: LPASS LPI pins SLEW registers + + clocks: + items: + - description: LPASS Core voting clock + - description: LPASS Audio voting clock + + clock-names: + items: + - const: core + - const: audio + + gpio-controller: true + + '#gpio-cells': + description: Specifying the pin number and flags, as defined in + include/dt-bindings/gpio/gpio.h + const: 2 + + gpio-ranges: + maxItems: 1 + +#PIN CONFIGURATION NODES +patternProperties: + '-pins$': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: /schemas/pinctrl/pincfg-node.yaml + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + pattern: "^gpio([0-9]|[1-2][0-9]])$" + + function: + enum: [ swr_tx_clk, swr_tx_data, swr_rx_clk, swr_rx_data, + dmic1_clk, dmic1_data, dmic2_clk, dmic2_data, dmic4_clk, + dmic4_data, i2s2_clk, i2s2_ws, dmic3_clk, dmic3_data, + qua_mi2s_sclk, qua_mi2s_ws, qua_mi2s_data, i2s1_clk, i2s1_ws, + i2s1_data, wsa_swr_clk, wsa_swr_data, wsa2_swr_clk, + wsa2_swr_data, i2s2_data, i2s4_ws, i2s4_clk, i2s4_data, + slimbus_clk, i2s3_clk, i2s3_ws, i2s3_data, slimbus_data, + ext_mclk1_c, ext_mclk1_b, ext_mclk1_a, ext_mclk1_d, + ext_mclk1_e ] + description: + Specify the alternative function to be configured for the specified + pins. + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + default: 2 + description: + Selects the drive strength for the specified pins, in mA. + + slew-rate: + enum: [0, 1, 2, 3] + default: 0 + description: | + 0: No adjustments + 1: Higher Slew rate (faster edges) + 2: Lower Slew rate (slower edges) + 3: Reserved (No adjustments) + + bias-pull-down: true + + bias-pull-up: true + + bias-disable: true + + output-high: true + + output-low: true + + required: + - pins + - function + + additionalProperties: false + +allOf: + - $ref: pinctrl.yaml# + +required: + - compatible + - reg + - clocks + - clock-names + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/sound/qcom,q6afe.h> + pinctrl@3440000 { + compatible = "qcom,sm8450-lpass-lpi-pinctrl"; + reg = <0x3440000 0x20000>, + <0x34d0000 0x10000>; + clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + clock-names = "core", "audio"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&lpi_tlmm 0 0 23>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-pinctrl.yaml new file mode 100644 index 000000000000..9cd97a467648 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-pinctrl.yaml @@ -0,0 +1,159 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,sm8450-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. SM8450 TLMM block + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +description: | + This binding describes the Top Level Mode Multiplexer (TLMM) block found + in the SM8450 platform. + +allOf: + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# + +properties: + compatible: + const: qcom,sm8450-tlmm + + reg: + maxItems: 1 + + interrupts: true + interrupt-controller: true + '#interrupt-cells': true + gpio-controller: true + + gpio-reserved-ranges: + minItems: 1 + maxItems: 105 + + gpio-line-names: + maxItems: 209 + + '#gpio-cells': true + gpio-ranges: true + wakeup-parent: true + +required: + - compatible + - reg + +additionalProperties: false + +patternProperties: + '-state$': + oneOf: + - $ref: "#/$defs/qcom-sm8450-tlmm-state" + - patternProperties: + "-pins$": + $ref: "#/$defs/qcom-sm8450-tlmm-state" + additionalProperties: false + +$defs: + qcom-sm8450-tlmm-state: + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-9][0-9]|20[0-9])$" + - enum: [ ufs_reset, sdc2_clk, sdc2_cmd, sdc2_data ] + minItems: 1 + maxItems: 36 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + enum: [ aon_cam, atest_char, atest_usb, audio_ref, cam_mclk, cci_async, + cci_i2c, cci_timer, cmu_rng, coex_uart1, coex_uart2, cri_trng, + cri_trng0, cri_trng1, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1, + ddr_pxi2, ddr_pxi3, dp_hot, gcc_gp1, gcc_gp2, gcc_gp3, + gpio, ibi_i3c, jitter_bist, mdp_vsync, mdp_vsync0, mdp_vsync1, + mdp_vsync2, mdp_vsync3, mi2s0_data0, mi2s0_data1, mi2s0_sck, + mi2s0_ws, mi2s2_data0, mi2s2_data1, mi2s2_sck, mi2s2_ws, + mss_grfc0, mss_grfc1, mss_grfc10, mss_grfc11, mss_grfc12, + mss_grfc2, mss_grfc3, mss_grfc4, mss_grfc5, mss_grfc6, + mss_grfc7, mss_grfc8, mss_grfc9, nav, pcie0_clkreqn, + pcie1_clkreqn, phase_flag, pll_bist, pll_clk, pri_mi2s, + prng_rosc, qdss_cti, qdss_gpio, qlink0_enable, qlink0_request, + qlink0_wmss, qlink1_enable, qlink1_request, qlink1_wmss, + qlink2_enable, qlink2_request, qlink2_wmss, qspi0, qspi1, + qspi2, qspi3, qspi_clk, qspi_cs, qup0, qup1, qup10, qup11, + qup12, qup13, qup14, qup15, qup16, qup17, qup18, qup19, qup2, + qup20, qup21, qup3, qup4, qup5, qup6, qup7, qup8, qup9, qup_l4, + qup_l5, qup_l6, sd_write, sdc40, sdc41, sdc42, sdc43, sdc4_clk, + sdc4_cmd, sec_mi2s, tb_trig, tgu_ch0, tgu_ch1, tgu_ch2, + tgu_ch3, tmess_prng0, tmess_prng1, tmess_prng2, tmess_prng3, + tsense_pwm1, tsense_pwm2, uim0_clk, uim0_data, uim0_present, + uim0_reset, uim1_clk, uim1_data, uim1_present, uim1_reset, + usb2phy_ac, usb_phy, vfr_0, vfr_1, vsense_trigger ] + + bias-disable: true + bias-pull-down: true + bias-pull-up: true + drive-strength: true + input-enable: true + output-high: true + output-low: true + + required: + - pins + + allOf: + - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" + - if: + properties: + pins: + pattern: "^gpio([0-9]|[1-9][0-9]|1[0-9][0-9]|20[0-9])$" + then: + required: + - function + + additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl@f100000 { + compatible = "qcom,sm8450-tlmm"; + reg = <0x0f100000 0x300000>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 211>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + + gpio-wo-state { + pins = "gpio1"; + function = "gpio"; + }; + + uart-w-state { + rx-pins { + pins = "gpio26"; + function = "qup7"; + bias-pull-up; + }; + + tx-pins { + pins = "gpio27"; + function = "qup7"; + bias-disable; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml index 3b37cf102d41..c88c8dcb69d9 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml @@ -42,7 +42,6 @@ properties: description: Specifying the interrupt-controller used to wake up the system when the TLMM block has been powered down. - maxItems: 1 gpio-reserved-ranges: description: @@ -51,6 +50,9 @@ properties: should not be accessed by the OS. Please see the ../gpio/gpio.txt for more information. +allOf: + - $ref: "pinctrl.yaml#" + required: - interrupts - interrupt-controller @@ -70,7 +72,6 @@ $defs: properties: drive-strength: enum: [2, 4, 6, 8, 10, 12, 14, 16] - default: 2 description: Selects the drive strength for the specified pins, in mA. diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,mt7620-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,mt7620-pinctrl.yaml new file mode 100644 index 000000000000..6f17f3991640 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ralink,mt7620-pinctrl.yaml @@ -0,0 +1,97 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/ralink,mt7620-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ralink MT7620 Pin Controller + +maintainers: + - Arınç ÜNAL <arinc.unal@arinc9.com> + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +description: + Ralink MT7620 pin controller for MT7620, MT7628 and MT7688 SoCs. + The pin controller can only set the muxing of pin groups. Muxing individual + pins is not supported. There is no pinconf support. + +properties: + compatible: + const: ralink,mt7620-pinctrl + +patternProperties: + '-pins$': + type: object + patternProperties: + '^(.*-)?pinmux$': + type: object + description: node for pinctrl. + $ref: pinmux-node.yaml# + + properties: + groups: + description: The pin group to select. + enum: [ + # common + i2c, spi, wdt, + + # For MT7620 SoC + ephy, mdio, nd_sd, pa, pcie, rgmii1, rgmii2, spi refclk, + uartf, uartlite, wled, + + # For MT7628 and MT7688 SoCs + gpio, i2s, p0led_an, p0led_kn, p1led_an, p1led_kn, p2led_an, + p2led_kn, p3led_an, p3led_kn, p4led_an, p4led_kn, perst, pwm0, + pwm1, refclk, sdmode, spi cs1, spis, uart0, uart1, uart2, + wled_an, wled_kn, + ] + + function: + description: The mux function to select. + enum: [ + # common + gpio, i2c, refclk, spi, + + # For MT7620 SoC + ephy, gpio i2s, gpio uartf, i2s uartf, mdio, nand, pa, + pcie refclk, pcie rst, pcm gpio, pcm i2s, pcm uartf, + rgmii1, rgmii2, sd, spi refclk, uartf, uartlite, wdt refclk, + wdt rst, wled, + + # For MT7628 and MT7688 SoCs + antenna, debug, i2s, jtag, p0led_an, p0led_kn, + p1led_an, p1led_kn, p2led_an, p2led_kn, p3led_an, p3led_kn, + p4led_an, p4led_kn, pcie, pcm, perst, pwm, pwm0, pwm1, pwm_uart2, + rsvd, sdxc, sdxc d5 d4, sdxc d6, sdxc d7, spi cs1, + spis, sw_r, uart0, uart1, uart2, utif, wdt, wled_an, wled_kn, -, + ] + + required: + - groups + - function + + additionalProperties: false + + additionalProperties: false + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + +additionalProperties: false + +examples: + # Pinmux controller node + - | + pinctrl { + compatible = "ralink,mt7620-pinctrl"; + + i2c_pins: i2c0-pins { + pinmux { + groups = "i2c"; + function = "i2c"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,mt7621-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,mt7621-pinctrl.yaml new file mode 100644 index 000000000000..61e5c847e8c8 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ralink,mt7621-pinctrl.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/ralink,mt7621-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ralink MT7621 Pin Controller + +maintainers: + - Arınç ÜNAL <arinc.unal@arinc9.com> + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +description: + Ralink MT7621 pin controller for MT7621 SoC. + The pin controller can only set the muxing of pin groups. Muxing individual + pins is not supported. There is no pinconf support. + +properties: + compatible: + const: ralink,mt7621-pinctrl + +patternProperties: + '-pins$': + type: object + patternProperties: + '^(.*-)?pinmux$': + type: object + description: node for pinctrl. + $ref: pinmux-node.yaml# + + properties: + groups: + description: The pin group to select. + enum: [i2c, jtag, mdio, pcie, rgmii1, rgmii2, sdhci, spi, uart1, + uart2, uart3, wdt] + + function: + description: The mux function to select. + enum: [gpio, i2c, i2s, jtag, mdio, nand1, nand2, pcie refclk, + pcie rst, pcm, rgmii1, rgmii2, sdhci, spdif2, spdif3, spi, + uart1, uart2, uart3, wdt refclk, wdt rst] + + required: + - groups + - function + + additionalProperties: false + + additionalProperties: false + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + +additionalProperties: false + +examples: + # Pinmux controller node + - | + pinctrl { + compatible = "ralink,mt7621-pinctrl"; + + i2c_pins: i2c0-pins { + pinmux { + groups = "i2c"; + function = "i2c"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinmux.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinctrl.yaml index b32f2676cab5..56e5becabcfd 100644 --- a/Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinmux.yaml +++ b/Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinctrl.yaml @@ -1,21 +1,23 @@ # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause %YAML 1.2 --- -$id: http://devicetree.org/schemas/pinctrl/ralink,rt2880-pinmux.yaml# +$id: http://devicetree.org/schemas/pinctrl/ralink,rt2880-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Ralink rt2880 pinmux controller +title: Ralink RT2880 Pin Controller maintainers: + - Arınç ÜNAL <arinc.unal@arinc9.com> - Sergio Paracuellos <sergio.paracuellos@gmail.com> description: - The rt2880 pinmux can only set the muxing of pin groups. muxing indiviual pins - is not supported. There is no pinconf support. + Ralink RT2880 pin controller for RT2880 SoC. + The pin controller can only set the muxing of pin groups. Muxing individual + pins is not supported. There is no pinconf support. properties: compatible: - const: ralink,rt2880-pinmux + const: ralink,rt2880-pinctrl patternProperties: '-pins$': @@ -28,13 +30,12 @@ patternProperties: properties: groups: - description: Name of the pin group to use for the functions. - enum: [i2c, spi, uart1, uart2, uart3, rgmii1, rgmii2, mdio, - pcie, sdhci] + description: The pin group to select. + enum: [i2c, spi, uartlite, jtag, mdio, sdram, pci] + function: - description: The mux function to select - enum: [gpio, i2c, spi, uart1, uart2, uart3, rgmii1, rgmii2, - mdio, nand1, nand2, sdhci] + description: The mux function to select. + enum: [gpio, i2c, spi, uartlite, jtag, mdio, sdram, pci] required: - groups @@ -44,6 +45,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible @@ -53,7 +57,7 @@ examples: # Pinmux controller node - | pinctrl { - compatible = "ralink,rt2880-pinmux"; + compatible = "ralink,rt2880-pinctrl"; i2c_pins: i2c0-pins { pinmux { diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,rt305x-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,rt305x-pinctrl.yaml new file mode 100644 index 000000000000..f602a5d6e13a --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ralink,rt305x-pinctrl.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/ralink,rt305x-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ralink RT305X Pin Controller + +maintainers: + - Arınç ÜNAL <arinc.unal@arinc9.com> + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +description: + Ralink RT305X pin controller for RT3050, RT3052, RT3350, RT3352 and RT5350 + SoCs. + The pin controller can only set the muxing of pin groups. Muxing individual + pins is not supported. There is no pinconf support. + +properties: + compatible: + const: ralink,rt305x-pinctrl + +patternProperties: + '-pins$': + type: object + patternProperties: + '^(.*-)?pinmux$': + type: object + description: node for pinctrl. + $ref: pinmux-node.yaml# + + properties: + groups: + description: The pin group to select. + enum: [ + # common + i2c, jtag, led, mdio, rgmii, spi, spi_cs1, uartf, uartlite, + + # For RT3050, RT3052 and RT3350 SoCs + sdram, + + # For RT3352 SoC + lna, pa + ] + + function: + description: The mux function to select. + enum: [ + # common + gpio, gpio i2s, gpio uartf, i2c, i2s uartf, jtag, led, mdio, + pcm gpio, pcm i2s, pcm uartf, rgmii, spi, spi_cs1, uartf, + uartlite, wdg_cs1, + + # For RT3050, RT3052 and RT3350 SoCs + sdram, + + # For RT3352 SoC + lna, pa + ] + + required: + - groups + - function + + additionalProperties: false + + additionalProperties: false + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + +additionalProperties: false + +examples: + # Pinmux controller node + - | + pinctrl { + compatible = "ralink,rt305x-pinctrl"; + + i2c_pins: i2c0-pins { + pinmux { + groups = "i2c"; + function = "i2c"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,rt3883-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,rt3883-pinctrl.yaml new file mode 100644 index 000000000000..feb6e66dcb61 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ralink,rt3883-pinctrl.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/ralink,rt3883-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ralink RT3883 Pin Controller + +maintainers: + - Arınç ÜNAL <arinc.unal@arinc9.com> + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +description: + Ralink RT3883 pin controller for RT3883 SoC. + The pin controller can only set the muxing of pin groups. Muxing individual + pins is not supported. There is no pinconf support. + +properties: + compatible: + const: ralink,rt3883-pinctrl + +patternProperties: + '-pins$': + type: object + patternProperties: + '^(.*-)?pinmux$': + type: object + description: node for pinctrl. + $ref: pinmux-node.yaml# + + properties: + groups: + description: The pin group to select. + enum: [ge1, ge2, i2c, jtag, lna a, lna g, mdio, pci, spi, uartf, + uartlite] + + function: + description: The mux function to select. + enum: [ge1, ge2, gpio, gpio i2s, gpio uartf, i2c, i2s uartf, jtag, + lna a, lna g, mdio, pci-dev, pci-fnc, pci-host1, pci-host2, + pcm gpio, pcm i2s, pcm uartf, spi, uartf, uartlite] + + required: + - groups + - function + + additionalProperties: false + + additionalProperties: false + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + +additionalProperties: false + +examples: + # Pinmux controller node + - | + pinctrl { + compatible = "ralink,rt3883-pinctrl"; + + i2c_pins: i2c0-pins { + pinmux { + groups = "i2c"; + function = "i2c"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml index ac4e068aa03f..4fc758fea7e6 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml @@ -44,6 +44,8 @@ properties: - renesas,pfc-r8a77990 # R-Car E3 - renesas,pfc-r8a77995 # R-Car D3 - renesas,pfc-r8a779a0 # R-Car V3U + - renesas,pfc-r8a779f0 # R-Car S4-8 + - renesas,pfc-r8a779g0 # R-Car V4H - renesas,pfc-sh73a0 # SH-Mobile AG5 reg: @@ -70,6 +72,9 @@ properties: power-domains: maxItems: 1 +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml index 7f80578dc229..9083040c996a 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml @@ -31,6 +31,9 @@ properties: reg: maxItems: 1 +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg @@ -38,6 +41,7 @@ required: patternProperties: "^gpio-[0-9]*$": type: object + additionalProperties: false description: Each port of the r7s72100 pin controller hardware is itself a GPIO diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml index ce1f7343788f..d761fddc2206 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml @@ -72,6 +72,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml index ef68dabcf4dc..f081acb7ba04 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml @@ -4,15 +4,15 @@ $id: http://devicetree.org/schemas/pinctrl/renesas,rzg2l-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Renesas RZ/G2L combined Pin and GPIO controller +title: Renesas RZ/{G2L,V2L} combined Pin and GPIO controller maintainers: - Geert Uytterhoeven <geert+renesas@glider.be> - Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> description: - The Renesas SoCs of the RZ/G2L series feature a combined Pin and GPIO - controller. + The Renesas SoCs of the RZ/{G2L,V2L} alike series feature a combined Pin and + GPIO controller. Pin multiplexing and GPIO configuration is performed on a per-pin basis. Each port features up to 8 pins, each of them configurable for GPIO function (port mode) or in alternate function mode. @@ -20,8 +20,16 @@ description: properties: compatible: - enum: - - renesas,r9a07g044-pinctrl # RZ/G2{L,LC} + oneOf: + - items: + - enum: + - renesas,r9a07g043-pinctrl # RZ/G2UL{Type-1,Type-2} and RZ/Five + - renesas,r9a07g044-pinctrl # RZ/G2{L,LC} + + - items: + - enum: + - renesas,r9a07g054-pinctrl # RZ/V2L + - const: renesas,r9a07g044-pinctrl # RZ/G2{L,LC} fallback for RZ/V2L reg: maxItems: 1 @@ -39,6 +47,17 @@ properties: gpio-ranges: maxItems: 1 + interrupt-controller: true + + '#interrupt-cells': + const: 2 + description: + The first cell contains the global GPIO port index, constructed using the + RZG2L_GPIO() helper macro in <dt-bindings/pinctrl/rzg2l-pinctrl.h> and the + second cell is used to specify the flag. + E.g. "interrupts = <RZG2L_GPIO(43, 0) IRQ_TYPE_EDGE_FALLING>;" if P43_0 is + being used as an interrupt. + clocks: maxItems: 1 @@ -73,7 +92,10 @@ additionalProperties: pins: true drive-strength: enum: [ 2, 4, 8, 12 ] + output-impedance-ohms: + enum: [ 33, 50, 66, 100 ] power-source: + description: I/O voltage in millivolt. enum: [ 1800, 2500, 3300 ] slew-rate: true gpio-hog: true @@ -90,12 +112,17 @@ additionalProperties: additionalProperties: $ref: "#/additionalProperties/anyOf/0" +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg - gpio-controller - '#gpio-cells' - gpio-ranges + - interrupt-controller + - '#interrupt-cells' - clocks - power-domains - resets @@ -112,6 +139,8 @@ examples: gpio-controller; #gpio-cells = <2>; gpio-ranges = <&pinctrl 0 0 392>; + interrupt-controller; + #interrupt-cells = <2>; clocks = <&cpg CPG_MOD R9A07G044_GPIO_HCLK>; resets = <&cpg R9A07G044_GPIO_RSTN>, <&cpg R9A07G044_GPIO_PORT_RESETN>, diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.yaml index 4a43af0d6e02..70b1788ab594 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.yaml @@ -31,6 +31,9 @@ properties: description: The bus clock, sometimes described as pclk, for register accesses. +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzv2m-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rzv2m-pinctrl.yaml new file mode 100644 index 000000000000..eac6245db7dc --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzv2m-pinctrl.yaml @@ -0,0 +1,170 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/renesas,rzv2m-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas RZ/V2M combined Pin and GPIO controller + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + - Phil Edworthy <phil.edworthy@renesas.com> + +description: + The Renesas RZ/V2M SoC features a combined Pin and GPIO controller. + Pin multiplexing and GPIO configuration is performed on a per-pin basis. + Each port features up to 16 pins, each of them configurable for GPIO function + (port mode) or in alternate function mode. + Up to 8 different alternate function modes exist for each single pin. + +properties: + compatible: + const: renesas,r9a09g011-pinctrl # RZ/V2M + + reg: + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + description: + The first cell contains the global GPIO port index, constructed using the + RZV2M_GPIO() helper macro in <dt-bindings/pinctrl/rzv2m-pinctrl.h> and the + second cell represents consumer flag as mentioned in ../gpio/gpio.txt + E.g. "RZV2M_GPIO(8, 1)" for P8_1. + + gpio-ranges: + maxItems: 1 + + interrupts: + description: INEXINT[0..38] corresponding to individual pin inputs. + maxItems: 39 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + +additionalProperties: + anyOf: + - type: object + allOf: + - $ref: pincfg-node.yaml# + - $ref: pinmux-node.yaml# + + description: + Pin controller client devices use pin configuration subnodes (children + and grandchildren) for desired pin configuration. + Client device subnodes use below standard properties. + + properties: + phandle: true + pinmux: + description: + Values are constructed from GPIO port number, pin number, and + alternate function configuration number using the RZV2M_PORT_PINMUX() + helper macro in <dt-bindings/pinctrl/rzv2m-pinctrl.h>. + pins: true + bias-disable: true + bias-pull-down: true + bias-pull-up: true + drive-strength-microamp: + # Superset of supported values + enum: [ 1600, 1800, 2000, 3200, 3800, 4000, 6400, 7800, 8000, + 9000, 9600, 11000, 12000, 13000, 18000 ] + slew-rate: + description: 0 is slow slew rate, 1 is fast slew rate + enum: [ 0, 1 ] + gpio-hog: true + gpios: true + output-high: true + output-low: true + line-name: true + + - type: object + properties: + phandle: true + + additionalProperties: + $ref: "#/additionalProperties/anyOf/0" + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + - reg + - gpio-controller + - '#gpio-cells' + - gpio-ranges + - interrupts + - clocks + - power-domains + - resets + +examples: + - | + #include <dt-bindings/pinctrl/rzv2m-pinctrl.h> + #include <dt-bindings/clock/r9a09g011-cpg.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pinctrl: pinctrl@b6250000 { + compatible = "renesas,r9a09g011-pinctrl"; + reg = <0xb6250000 0x800>; + + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl 0 0 352>; + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD R9A09G011_PFC_PCLK>; + resets = <&cpg R9A09G011_PFC_PRESETN>; + power-domains = <&cpg>; + + i2c2_pins: i2c2 { + pinmux = <RZV2M_PORT_PINMUX(3, 8, 2)>, /* SDA */ + <RZV2M_PORT_PINMUX(3, 9, 2)>; /* SCL */ + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.yaml index 07c0a98ef9c6..b486f41df65f 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.yaml @@ -33,6 +33,7 @@ properties: enum: - rockchip,px30-pinctrl - rockchip,rk2928-pinctrl + - rockchip,rk3036-pinctrl - rockchip,rk3066a-pinctrl - rockchip,rk3066b-pinctrl - rockchip,rk3128-pinctrl @@ -44,7 +45,9 @@ properties: - rockchip,rk3368-pinctrl - rockchip,rk3399-pinctrl - rockchip,rk3568-pinctrl + - rockchip,rk3588-pinctrl - rockchip,rv1108-pinctrl + - rockchip,rv1126-pinctrl rockchip,grf: $ref: "/schemas/types.yaml#/definitions/phandle" @@ -67,6 +70,9 @@ properties: ranges: true +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - rockchip,grf @@ -126,7 +132,7 @@ additionalProperties: description: Pin bank index. - minimum: 0 - maximum: 6 + maximum: 10 description: Mux 0 means GPIO and mux 1 to N means the specific device function. diff --git a/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl-gpio-bank.yaml b/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl-gpio-bank.yaml new file mode 100644 index 000000000000..8cf3c47ab86b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl-gpio-bank.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/samsung,pinctrl-gpio-bank.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S3C/S5P/Exynos SoC pin controller - gpio bank + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + - Tomasz Figa <tomasz.figa@gmail.com> + +description: | + This is a part of device tree bindings for Samsung S3C/S5P/Exynos SoC pin + controller. + + GPIO bank description for Samsung S3C/S5P/Exynos SoC pin controller. + + See also Documentation/devicetree/bindings/pinctrl/samsung,pinctrl.yaml for + additional information and example. + +properties: + '#gpio-cells': + const: 2 + + gpio-controller: true + + '#interrupt-cells': + description: + For GPIO banks supporting external GPIO interrupts or external wake-up + interrupts. + const: 2 + + interrupt-controller: + description: + For GPIO banks supporting external GPIO interrupts or external wake-up + interrupts. + + interrupts: + description: + For GPIO banks supporting direct external wake-up interrupts (without + multiplexing). Number of interrupts must match number of wake-up capable + pins of this bank. + minItems: 1 + maxItems: 8 + +required: + - '#gpio-cells' + - gpio-controller + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl-pins-cfg.yaml b/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl-pins-cfg.yaml new file mode 100644 index 000000000000..f796f27bf0e6 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl-pins-cfg.yaml @@ -0,0 +1,80 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/samsung,pinctrl-pins-cfg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S3C/S5P/Exynos SoC pin controller - pins configuration + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + - Tomasz Figa <tomasz.figa@gmail.com> + +description: | + This is a part of device tree bindings for Samsung S3C/S5P/Exynos SoC pin + controller. + + Pins configuration for Samsung S3C/S5P/Exynos SoC pin controller. + + The values used for config properties should be derived from the hardware + manual and these values are programmed as-is into the pin pull up/down and + driver strength register of the pin-controller. + + See also Documentation/devicetree/bindings/pinctrl/samsung,pinctrl.yaml for + additional information and example. + +properties: + samsung,pins: + description: | + List of pins to configure. For initial and sleep states, the maximum + number is one pin. In other cases there is no upper limit. + + The pins should use lowercase names matching hardware manual, e.g. for + GPA0 bank: gpa0-0, gpa0-1, gpa0-2. + $ref: /schemas/types.yaml#/definitions/string-array + + samsung,pin-function: + description: | + The pin function selection that should be applied on the pins listed in the + child node is specified using the "samsung,pin-function" property. The value + of this property that should be applied to each of the pins listed in the + "samsung,pins" property should be picked from the hardware manual of the SoC + for the specified pin group. This property is optional in the child node if + no specific function selection is desired for the pins listed in the child + node. The value of this property is used as-is to program the pin-controller + function selector register of the pin-bank. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + + samsung,pin-drv: + description: Drive strength configuration. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + + samsung,pin-pud: + description: Pull up/down configuration. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + + samsung,pin-val: + description: Initial value of pin output buffer. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + + samsung,pin-con-pdn: + description: Function in power down mode. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + + samsung,pin-pud-pdn: + description: Pull up/down configuration in power down mode. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + +required: + - samsung,pins + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl-wakeup-interrupt.yaml b/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl-wakeup-interrupt.yaml new file mode 100644 index 000000000000..1de91a51234d --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl-wakeup-interrupt.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/samsung,pinctrl-wakeup-interrupt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S3C/S5P/Exynos SoC pin controller - wake-up interrupt controller + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + - Tomasz Figa <tomasz.figa@gmail.com> + +description: | + This is a part of device tree bindings for Samsung S3C/S5P/Exynos SoC pin + controller. + + External wake-up interrupts for Samsung S3C/S5P/Exynos SoC pin controller. + For S3C24xx, S3C64xx, S5PV210 and Exynos4210 compatible wake-up interrupt + controllers, only one pin-controller device node can include external wake-up + interrupts child node (in other words, only one External wake-up interrupts + pin-controller is supported). + For newer controllers, multiple pin-controller device node can include + external wake-up interrupts child node. + + See also Documentation/devicetree/bindings/pinctrl/samsung,pinctrl.yaml for + additional information and example. + +properties: + compatible: + enum: + - samsung,s3c2410-wakeup-eint + - samsung,s3c2412-wakeup-eint + - samsung,s3c64xx-wakeup-eint + - samsung,s5pv210-wakeup-eint + - samsung,exynos4210-wakeup-eint + - samsung,exynos7-wakeup-eint + - samsung,exynos850-wakeup-eint + - samsung,exynosautov9-wakeup-eint + + interrupts: + description: + Interrupt used by multiplexed external wake-up interrupts. + minItems: 1 + maxItems: 6 + +required: + - compatible + +allOf: + - if: + properties: + compatible: + contains: + enum: + - samsung,s3c2410-wakeup-eint + - samsung,s3c2412-wakeup-eint + then: + properties: + interrupts: + minItems: 6 + maxItems: 6 + required: + - interrupts + + - if: + properties: + compatible: + contains: + const: samsung,s3c64xx-wakeup-eint + then: + properties: + interrupts: + minItems: 4 + maxItems: 4 + required: + - interrupts + + - if: + properties: + compatible: + contains: + enum: + - samsung,s5pv210-wakeup-eint + - samsung,exynos4210-wakeup-eint + - samsung,exynos7-wakeup-eint + then: + properties: + interrupts: + minItems: 1 + maxItems: 1 + required: + - interrupts + + - if: + properties: + compatible: + contains: + enum: + - samsung,exynos850-wakeup-eint + - samsung,exynosautov9-wakeup-eint + then: + properties: + interrupts: false + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl.yaml new file mode 100644 index 000000000000..eb2b2692607d --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl.yaml @@ -0,0 +1,387 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/samsung,pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S3C/S5P/Exynos SoC pin controller + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + - Tomasz Figa <tomasz.figa@gmail.com> + +description: | + This is a part of device tree bindings for Samsung S3C/S5P/Exynos SoC pin + controller. + + All the pin controller nodes should be represented in the aliases node using + the following format 'pinctrl{n}' where n is a unique number for the alias. + + The controller supports three types of interrupts:: + - External GPIO interrupts (see interrupts property in pin controller node); + + - External wake-up interrupts - multiplexed (capable of waking up the system + see interrupts property in external wake-up interrupt controller node - + samsung,pinctrl-wakeup-interrupt.yaml); + + - External wake-up interrupts - direct (capable of waking up the system, see + interrupts property in every bank of pin controller with external wake-up + interrupt controller - samsung,pinctrl-gpio-bank.yaml). + +properties: + $nodename: + pattern: "^pinctrl(@.*)?" + + compatible: + enum: + - samsung,s3c2412-pinctrl + - samsung,s3c2416-pinctrl + - samsung,s3c2440-pinctrl + - samsung,s3c2450-pinctrl + - samsung,s3c64xx-pinctrl + - samsung,s5pv210-pinctrl + - samsung,exynos3250-pinctrl + - samsung,exynos4210-pinctrl + - samsung,exynos4x12-pinctrl + - samsung,exynos5250-pinctrl + - samsung,exynos5260-pinctrl + - samsung,exynos5410-pinctrl + - samsung,exynos5420-pinctrl + - samsung,exynos5433-pinctrl + - samsung,exynos7-pinctrl + - samsung,exynos7885-pinctrl + - samsung,exynos850-pinctrl + - samsung,exynosautov9-pinctrl + - tesla,fsd-pinctrl + + interrupts: + description: + Required for GPIO banks supporting external GPIO interrupts. + maxItems: 1 + + power-domains: + maxItems: 1 + + reg: + description: + Second base address of the pin controller if the specific registers of + the pin controller are separated into the different base address. + Only certain banks of certain pin controller might need it. + minItems: 1 + maxItems: 2 + + wakeup-interrupt-controller: + $ref: samsung,pinctrl-wakeup-interrupt.yaml + +patternProperties: + "^[a-z]+[0-9]*-gpio-bank$": + description: + Pin banks of the controller are represented by child nodes of the + controller node. Bank name is taken from name of the node. + $ref: samsung,pinctrl-gpio-bank.yaml + + "^[a-z0-9-]+-pins$": + oneOf: + - $ref: samsung,pinctrl-pins-cfg.yaml + required: + - samsung,pins + - type: object + patternProperties: + "^[a-z0-9-]+-pins$": + $ref: samsung,pinctrl-pins-cfg.yaml + + additionalProperties: false + + "^(initial|sleep)-state$": + type: object + additionalProperties: false + + patternProperties: + "^(pin-[a-z0-9-]+|[a-z0-9-]+-pin)$": + $ref: samsung,pinctrl-pins-cfg.yaml + + properties: + samsung,pins: + description: See samsung,pinctrl-pins-cfg.yaml + $ref: /schemas/types.yaml#/definitions/string-array + maxItems: 1 + + required: + - samsung,pins + + unevaluatedProperties: false + +required: + - compatible + - reg + +allOf: + - $ref: "pinctrl.yaml#" + - if: + properties: + compatible: + contains: + const: samsung,exynos5433-pinctrl + then: + properties: + reg: + minItems: 1 + maxItems: 2 + else: + properties: + reg: + minItems: 1 + maxItems: 1 + +additionalProperties: false + +examples: + - | + pinctrl@7f008000 { + compatible = "samsung,s3c64xx-pinctrl"; + reg = <0x7f008000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <21>; + + wakeup-interrupt-controller { + compatible = "samsung,s3c64xx-wakeup-eint"; + interrupts-extended = <&vic0 0>, + <&vic0 1>, + <&vic1 0>, + <&vic1 1>; + }; + + /* Pin bank with external GPIO or muxed external wake-up interrupts */ + gpa-gpio-bank { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + // ... + + uart0-data-pins { + samsung,pins = "gpa-0", "gpa-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + }; + + // ... + }; + + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pinctrl@11400000 { + compatible = "samsung,exynos4210-pinctrl"; + reg = <0x11400000 0x1000>; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&sleep0>; + + /* Pin bank with external GPIO or muxed external wake-up interrupts */ + gpa0-gpio-bank { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + // ... + + uart0-data-pins { + samsung,pins = "gpa0-0", "gpa0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + // ... + + sleep0: sleep-state { + gpa0-0-pin { + samsung,pins = "gpa0-0"; + samsung,pin-con-pdn = <2>; + samsung,pin-pud-pdn = <0>; + }; + + gpa0-1-pin { + samsung,pins = "gpa0-1"; + samsung,pin-con-pdn = <0>; + samsung,pin-pud-pdn = <0>; + }; + + // ... + }; + }; + + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pinctrl@11000000 { + compatible = "samsung,exynos4210-pinctrl"; + reg = <0x11000000 0x1000>; + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; + + wakeup-interrupt-controller { + compatible = "samsung,exynos4210-wakeup-eint"; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + }; + + /* Pin bank with external GPIO or muxed external wake-up interrupts */ + gpj0-gpio-bank { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + /* Pin bank without external interrupts */ + gpy0-gpio-bank { + gpio-controller; + #gpio-cells = <2>; + }; + + /* Pin bank with external direct wake-up interrupts */ + gpx0-gpio-bank { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <2>; + }; + + // ... + + sd0-clk-pins { + samsung,pins = "gpk0-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <3>; + }; + + sd4-bus-width8-pins { + part-1-pins { + samsung,pins = "gpk0-3", "gpk0-4", + "gpk0-5", "gpk0-6"; + samsung,pin-function = <3>; + samsung,pin-pud = <3>; + samsung,pin-drv = <3>; + }; + + part-2-pins { + samsung,pins = "gpk1-3", "gpk1-4", + "gpk1-5", "gpk1-6"; + samsung,pin-function = <4>; + samsung,pin-pud = <3>; + samsung,pin-drv = <3>; + }; + }; + + // ... + + otg-gp-pins { + samsung,pins = "gpx3-3"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + samsung,pin-val = <0>; + }; + }; + + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pinctrl@10580000 { + compatible = "samsung,exynos5433-pinctrl"; + reg = <0x10580000 0x1a20>, <0x11090000 0x100>; + + pinctrl-names = "default"; + pinctrl-0 = <&initial_alive>; + + wakeup-interrupt-controller { + compatible = "samsung,exynos7-wakeup-eint"; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + }; + + /* Pin bank with external direct wake-up interrupts */ + gpa0-gpio-bank { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <2>; + }; + + // ... + + te-irq-pins { + samsung,pins = "gpf1-3"; + samsung,pin-function = <0xf>; + }; + + // .. + + initial_alive: initial-state { + gpa0-0-pin { + samsung,pins = "gpa0-0"; + samsung,pin-function = <0>; + samsung,pin-pud = <1>; + samsung,pin-drv = <0>; + }; + + // ... + }; + }; + + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pinctrl@114b0000 { + compatible = "samsung,exynos5433-pinctrl"; + reg = <0x114b0000 0x1000>; + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&pd_aud>; + + /* Pin bank with external GPIO or muxed external wake-up interrupts */ + gpz0-gpio-bank { + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + // ... + + i2s0-bus-pins { + samsung,pins = "gpz0-0", "gpz0-1", "gpz0-2", "gpz0-3", + "gpz0-4", "gpz0-5", "gpz0-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + // ... + }; diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt deleted file mode 100644 index b8b475967ff9..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ /dev/null @@ -1,382 +0,0 @@ -Samsung GPIO and Pin Mux/Config controller - -Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware -controller. It controls the input/output settings on the available pads/pins -and also provides ability to multiplex and configure the output of various -on-chip controllers onto these pads. - -Required Properties: -- compatible: should be one of the following. - - "samsung,s3c2412-pinctrl": for S3C2412-compatible pin-controller, - - "samsung,s3c2416-pinctrl": for S3C2416-compatible pin-controller, - - "samsung,s3c2440-pinctrl": for S3C2440-compatible pin-controller, - - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller, - - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller, - - "samsung,s5pv210-pinctrl": for S5PV210-compatible pin-controller, - - "samsung,exynos3250-pinctrl": for Exynos3250 compatible pin-controller. - - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller. - - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller. - - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller. - - "samsung,exynos5260-pinctrl": for Exynos5260 compatible pin-controller. - - "samsung,exynos5410-pinctrl": for Exynos5410 compatible pin-controller. - - "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller. - - "samsung,exynos5433-pinctrl": for Exynos5433 compatible pin-controller. - - "samsung,exynos7-pinctrl": for Exynos7 compatible pin-controller. - - "samsung,exynos850-pinctrl": for Exynos850 compatible pin-controller. - - "samsung,exynosautov9-pinctrl": for ExynosAutov9 compatible pin-controller. - -- reg: Base address of the pin controller hardware module and length of - the address space it occupies. - - - reg: Second base address of the pin controller if the specific registers - of the pin controller are separated into the different base address. - - Eg: GPF[1-5] of Exynos5433 are separated into the two base address. - - First base address is for GPAx and GPF[1-5] external interrupt - registers. - - Second base address is for GPF[1-5] pinctrl registers. - - pinctrl_0: pinctrl@10580000 { - compatible = "samsung,exynos5433-pinctrl"; - reg = <0x10580000 0x1a20>, <0x11090000 0x100>; - - wakeup-interrupt-controller { - compatible = "samsung,exynos7-wakeup-eint"; - interrupts = <0 16 0>; - }; - }; - -- Pin banks as child nodes: Pin banks of the controller are represented by child - nodes of the controller node. Bank name is taken from name of the node. Each - bank node must contain following properties: - - - gpio-controller: identifies the node as a gpio controller and pin bank. - - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO - binding is used, the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. - - Eg: <&gpx2 6 0> - <[phandle of the gpio controller node] - [pin number within the gpio controller] - [flags]> - - Values for gpio specifier: - - Pin number: is a value between 0 to 7. - - Flags: 0 - Active High - 1 - Active Low - -- Pin mux/config groups as child nodes: The pin mux (selecting pin function - mode) and pin config (pull up/down, driver strength) settings are represented - as child nodes of the pin-controller node. There should be at least one - child node and there is no limit on the count of these child nodes. It is - also possible for a child node to consist of several further child nodes - to allow grouping multiple pinctrl groups into one. The format of second - level child nodes is exactly the same as for first level ones and is - described below. - - The child node should contain a list of pin(s) on which a particular pin - function selection or pin configuration (or both) have to applied. This - list of pins is specified using the property name "samsung,pins". There - should be at least one pin specified for this property and there is no upper - limit on the count of pins that can be specified. The pins are specified - using pin names which are derived from the hardware manual of the SoC. As - an example, the pins in GPA0 bank of the pin controller can be represented - as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case. - The format of the pin names should be (as per the hardware manual) - "[pin bank name]-[pin number within the bank]". - - The pin function selection that should be applied on the pins listed in the - child node is specified using the "samsung,pin-function" property. The value - of this property that should be applied to each of the pins listed in the - "samsung,pins" property should be picked from the hardware manual of the SoC - for the specified pin group. This property is optional in the child node if - no specific function selection is desired for the pins listed in the child - node. The value of this property is used as-is to program the pin-controller - function selector register of the pin-bank. - - The child node can also optionally specify one or more of the pin - configuration that should be applied on all the pins listed in the - "samsung,pins" property of the child node. The following pin configuration - properties are supported. - - - samsung,pin-val: Initial value of pin output buffer. - - samsung,pin-pud: Pull up/down configuration. - - samsung,pin-drv: Drive strength configuration. - - samsung,pin-pud-pdn: Pull up/down configuration in power down mode. - - samsung,pin-drv-pdn: Drive strength configuration in power down mode. - - The values specified by these config properties should be derived from the - hardware manual and these values are programmed as-is into the pin - pull up/down and driver strength register of the pin-controller. - - Note: A child should include at least a pin function selection property or - pin configuration property (one or more) or both. - - The client nodes that require a particular pin function selection and/or - pin configuration should use the bindings listed in the "pinctrl-bindings.txt" - file. - -External GPIO and Wakeup Interrupts: - -The controller supports two types of external interrupts over gpio. The first -is the external gpio interrupt and second is the external wakeup interrupts. -The difference between the two is that the external wakeup interrupts can be -used as system wakeup events. - -A. External GPIO Interrupts: For supporting external gpio interrupts, the - following properties should be specified in the pin-controller device node. - - - interrupts: interrupt specifier for the controller. The format and value of - the interrupt specifier depends on the interrupt parent for the controller. - - In addition, following properties must be present in node of every bank - of pins supporting GPIO interrupts: - - - interrupt-controller: identifies the controller node as interrupt-parent. - - #interrupt-cells: the value of this property should be 2. - - First Cell: represents the external gpio interrupt number local to the - external gpio interrupt space of the controller. - - Second Cell: flags to identify the type of the interrupt - - 1 = rising edge triggered - - 2 = falling edge triggered - - 3 = rising and falling edge triggered - - 4 = high level triggered - - 8 = low level triggered - -B. External Wakeup Interrupts: For supporting external wakeup interrupts, a - child node representing the external wakeup interrupt controller should be - included in the pin-controller device node. - - Only one pin-controller device node can include external wakeup interrupts - child node (in other words, only one External Wakeup Interrupts - pin-controller is supported). - - This child node should include following properties: - - - compatible: identifies the type of the external wakeup interrupt controller - The possible values are: - - samsung,s3c2410-wakeup-eint: represents wakeup interrupt controller - found on Samsung S3C24xx SoCs except S3C2412 and S3C2413, - - samsung,s3c2412-wakeup-eint: represents wakeup interrupt controller - found on Samsung S3C2412 and S3C2413 SoCs, - - samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller - found on Samsung S3C64xx SoCs, - - samsung,s5pv210-wakeup-eint: represents wakeup interrupt controller - found on Samsung S5Pv210 SoCs, - - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller - found on Samsung Exynos4210 and S5PC110/S5PV210 SoCs. - - samsung,exynos7-wakeup-eint: represents wakeup interrupt controller - found on Samsung Exynos7 SoC. - - interrupts: interrupt used by multiplexed wakeup interrupts. - - In addition, following properties must be present in node of every bank - of pins supporting wake-up interrupts: - - - interrupt-controller: identifies the node as interrupt-parent. - - #interrupt-cells: the value of this property should be 2 - - First Cell: represents the external wakeup interrupt number local to - the external wakeup interrupt space of the controller. - - Second Cell: flags to identify the type of the interrupt - - 1 = rising edge triggered - - 2 = falling edge triggered - - 3 = rising and falling edge triggered - - 4 = high level triggered - - 8 = low level triggered - - Node of every bank of pins supporting direct wake-up interrupts (without - multiplexing) must contain following properties: - - - interrupts: interrupts of the interrupt parent which are used for external - wakeup interrupts from pins of the bank, must contain interrupts for all - pins of the bank. - -Aliases: - -All the pin controller nodes should be represented in the aliases node using -the following format 'pinctrl{n}' where n is a unique number for the alias. - -Aliases for controllers compatible with "samsung,exynos7-pinctrl": -- pinctrl0: pin controller of ALIVE block, -- pinctrl1: pin controller of BUS0 block, -- pinctrl2: pin controller of NFC block, -- pinctrl3: pin controller of TOUCH block, -- pinctrl4: pin controller of FF block, -- pinctrl5: pin controller of ESE block, -- pinctrl6: pin controller of FSYS0 block, -- pinctrl7: pin controller of FSYS1 block, -- pinctrl8: pin controller of BUS1 block, -- pinctrl9: pin controller of AUDIO block, - -Example: A pin-controller node with pin banks: - - pinctrl_0: pinctrl@11400000 { - compatible = "samsung,exynos4210-pinctrl"; - reg = <0x11400000 0x1000>; - interrupts = <0 47 0>; - - /* ... */ - - /* Pin bank without external interrupts */ - gpy0: gpy0 { - gpio-controller; - #gpio-cells = <2>; - }; - - /* ... */ - - /* Pin bank with external GPIO or muxed wake-up interrupts */ - gpj0: gpj0 { - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - /* ... */ - - /* Pin bank with external direct wake-up interrupts */ - gpx0: gpx0 { - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - interrupt-parent = <&gic>; - interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>, - <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>; - #interrupt-cells = <2>; - }; - - /* ... */ - }; - -Example 1: A pin-controller node with pin groups. - - #include <dt-bindings/pinctrl/samsung.h> - - pinctrl_0: pinctrl@11400000 { - compatible = "samsung,exynos4210-pinctrl"; - reg = <0x11400000 0x1000>; - interrupts = <0 47 0>; - - /* ... */ - - uart0_data: uart0-data { - samsung,pins = "gpa0-0", "gpa0-1"; - samsung,pin-function = <EXYNOS_PIN_FUNC_2>; - samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; - samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; - }; - - uart0_fctl: uart0-fctl { - samsung,pins = "gpa0-2", "gpa0-3"; - samsung,pin-function = <EXYNOS_PIN_FUNC_2>; - samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; - samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; - }; - - uart1_data: uart1-data { - samsung,pins = "gpa0-4", "gpa0-5"; - samsung,pin-function = <EXYNOS_PIN_FUNC_2>; - samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; - samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; - }; - - uart1_fctl: uart1-fctl { - samsung,pins = "gpa0-6", "gpa0-7"; - samsung,pin-function = <EXYNOS_PIN_FUNC_2>; - samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; - samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; - }; - - i2c2_bus: i2c2-bus { - samsung,pins = "gpa0-6", "gpa0-7"; - samsung,pin-function = <EXYNOS_PIN_FUNC_3>; - samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; - samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; - }; - - sd4_bus8: sd4-bus-width8 { - part-1 { - samsung,pins = "gpk0-3", "gpk0-4", - "gpk0-5", "gpk0-6"; - samsung,pin-function = <EXYNOS_PIN_FUNC_3>; - samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; - samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>; - }; - part-2 { - samsung,pins = "gpk1-3", "gpk1-4", - "gpk1-5", "gpk1-6"; - samsung,pin-function = <EXYNOS_PIN_FUNC_4>; - samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; - samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>; - }; - }; - }; - -Example 2: A pin-controller node with external wakeup interrupt controller node. - - pinctrl_1: pinctrl@11000000 { - compatible = "samsung,exynos4210-pinctrl"; - reg = <0x11000000 0x1000>; - interrupts = <0 46 0> - - /* ... */ - - wakeup-interrupt-controller { - compatible = "samsung,exynos4210-wakeup-eint"; - interrupt-parent = <&gic>; - interrupts = <0 32 0>; - }; - }; - -Example 3: A uart client node that supports 'default' and 'flow-control' states. - - uart@13800000 { - compatible = "samsung,exynos4210-uart"; - reg = <0x13800000 0x100>; - interrupts = <0 52 0>; - pinctrl-names = "default", "flow-control; - pinctrl-0 = <&uart0_data>; - pinctrl-1 = <&uart0_data>, <&uart0_fctl>; - }; - -Example 4: Set up the default pin state for uart controller. - - static int s3c24xx_serial_probe(struct platform_device *pdev) { - struct pinctrl *pinctrl; - - /* ... */ - - pinctrl = devm_pinctrl_get_select_default(&pdev->dev); - } - -Example 5: A display port client node that supports 'default' pinctrl state - and gpio binding. - - display-port-controller { - /* ... */ - - samsung,hpd-gpio = <&gpx2 6 0>; - pinctrl-names = "default"; - pinctrl-0 = <&dp_hpd>; - }; - -Example 6: Request the gpio for display port controller - - static int exynos_dp_probe(struct platform_device *pdev) - { - int hpd_gpio, ret; - struct device *dev = &pdev->dev; - struct device_node *dp_node = dev->of_node; - - /* ... */ - - hpd_gpio = of_get_named_gpio(dp_node, "samsung,hpd-gpio", 0); - - /* ... */ - - ret = devm_gpio_request_one(&pdev->dev, hpd_gpio, GPIOF_IN, - "hpd_gpio"); - /* ... */ - } diff --git a/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.yaml index a804d9bc1602..14a8c0215cc6 100644 --- a/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.yaml @@ -10,9 +10,6 @@ maintainers: - Masahiro Yamada <yamada.masahiro@socionext.com> properties: - $nodename: - pattern: "pinctrl" - compatible: enum: - socionext,uniphier-ld4-pinctrl @@ -26,11 +23,48 @@ properties: - socionext,uniphier-pxs3-pinctrl - socionext,uniphier-nx1-pinctrl +additionalProperties: + type: object + + allOf: + - $ref: pincfg-node.yaml# + - $ref: pinmux-node.yaml# + + properties: + phandle: true + function: true + groups: true + pins: true + bias-pull-up: true + bias-pull-down: true + bias-pull-pin-default: true + drive-strength: true + + additionalProperties: + type: object + + allOf: + - $ref: pincfg-node.yaml# + - $ref: pinmux-node.yaml# + + properties: + phandle: true + function: true + groups: true + pins: true + bias-pull-up: true + bias-pull-down: true + bias-pull-pin-default: true + drive-strength: true + + unevaluatedProperties: false + +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible -additionalProperties: false - examples: - | // The UniPhier pinctrl should be a subnode of a "syscon" compatible node. diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml index ac88e01ec430..9d59208d83c1 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml @@ -41,11 +41,13 @@ properties: maxItems: 1 st,syscfg: - description: Should be phandle/offset/mask - - Phandle to the syscon node which includes IRQ mux selection. - - The offset of the IRQ mux selection register. - - The field mask of IRQ mux, needed if different of 0xf. + description: Phandle+args to the syscon node which includes IRQ mux selection. $ref: "/schemas/types.yaml#/definitions/phandle-array" + items: + - items: + - description: syscon node which includes IRQ mux selection + - description: The offset of the IRQ mux selection register + - description: The field mask of IRQ mux, needed if different of 0xf st,package: description: @@ -57,18 +59,22 @@ properties: patternProperties: '^gpio@[0-9a-f]*$': type: object + additionalProperties: false properties: gpio-controller: true '#gpio-cells': const: 2 + interrupt-controller: true + '#interrupt-cells': + const: 2 reg: maxItems: 1 clocks: maxItems: 1 - reset: - minItems: 1 + resets: maxItems: 1 + gpio-line-names: true gpio-ranges: minItems: 1 maxItems: 16 @@ -104,6 +110,12 @@ patternProperties: minimum: 0 maximum: 11 + patternProperties: + "^(.+-hog(-[0-9]+)?)$": + type: object + required: + - gpio-hog + required: - gpio-controller - '#gpio-cells' @@ -113,9 +125,12 @@ patternProperties: '-[0-9]*$': type: object + additionalProperties: false + patternProperties: '^pins': type: object + additionalProperties: false description: | A pinctrl node should contain at least one subnode representing the pinctrl group available on the machine. Each subnode will list the @@ -183,6 +198,9 @@ patternProperties: required: - pinmux +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - '#address-cells' diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml index 92963604422f..69c0dd9998ea 100644 --- a/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/pinctrl/starfive,jh7100-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: StarFive JH7100 Pin Controller Device Tree Bindings +title: StarFive JH7100 Pin Controller description: | Bindings for the JH7100 RISC-V SoC from StarFive Ltd. @@ -165,7 +165,7 @@ examples: - | #include <dt-bindings/clock/starfive-jh7100.h> #include <dt-bindings/reset/starfive-jh7100.h> - #include <dt-bindings/pinctrl/pinctrl-starfive.h> + #include <dt-bindings/pinctrl/pinctrl-starfive-jh7100.h> soc { #address-cells = <2>; diff --git a/Documentation/devicetree/bindings/pinctrl/sunplus,sp7021-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/sunplus,sp7021-pinctrl.yaml new file mode 100644 index 000000000000..347061eece9e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/sunplus,sp7021-pinctrl.yaml @@ -0,0 +1,377 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) Sunplus Co., Ltd. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/sunplus,sp7021-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sunplus SP7021 Pin Controller + +maintainers: + - Dvorkin Dmitry <dvorkin@tibbo.com> + - Wells Lu <wellslutw@gmail.com> + +description: | + The Sunplus SP7021 pin controller is used to control SoC pins. Please + refer to pinctrl-bindings.txt in this directory for details of the common + pinctrl bindings used by client devices. + + SP7021 has 99 digital GPIO pins which are numbered from GPIO 0 to 98. All + are multiplexed with some special function pins. SP7021 has 3 types of + special function pins: + + (1) function-group pins: + Ex 1 (SPI-NOR flash): + If control-field SPI_FLASH_SEL is set to 1, GPIO 83, 84, 86 and 87 + will be pins of SPI-NOR flash. If it is set to 2, GPIO 76, 78, 79 + and 81 will be pins of SPI-NOR flash. + + Ex 2 (UART_0): + If control-bit UA0_SEL is set to 1, GPIO 88 and 89 will be TX and + RX pins of UART_0 (UART channel 0). + + Ex 3 (eMMC): + If control-bit EMMC_SEL is set to 1, GPIO 72, 73, 74, 75, 76, 77, + 78, 79, 80, 81 will be pins of an eMMC device. + + Properties "function" and "groups" are used to select function-group + pins. + + (2) fully pin-mux (like phone exchange mux) pins: + GPIO 8 to 71 are 'fully pin-mux' pins. Any pins of peripherals of + SP7021 (ex: UART_1, UART_2, UART_3, UART_4, I2C_0, I2C_1, and etc.) + can be routed to any pins of fully pin-mux pins. + + Ex 1 (UART channel 1): + If control-field UA1_TX_SEL is set to 3, TX pin of UART_1 will be + routed to GPIO 10 (3 - 1 + 8 = 10). + If control-field UA1_RX_SEL is set to 4, RX pin of UART_1 will be + routed to GPIO 11 (4 - 1 + 8 = 11). + If control-field UA1_RTS_SEL is set to 5, RTS pin of UART_1 will + be routed to GPIO 12 (5 - 1 + 8 = 12). + If control-field UA1_CTS_SEL is set to 6, CTS pin of UART_1 will + be routed to GPIO 13 (6 - 1 + 8 = 13). + + Ex 2 (I2C channel 0): + If control-field I2C0_CLK_SEL is set to 20, CLK pin of I2C_0 will + be routed to GPIO 27 (20 - 1 + 8 = 27). + If control-field I2C0_DATA_SEL is set to 21, DATA pin of I2C_0 + will be routed to GPIO 28 (21 - 1 + 9 = 28). + + Totally, SP7021 has 120 peripheral pins. The peripheral pins can be + routed to any of 64 'fully pin-mux' pins. + + (3) I/O processor pins + SP7021 has a built-in I/O processor. + Any GPIO pins (GPIO 0 to 98) can be set to pins of I/O processor. + + Vendor property "sunplus,pins" is used to select "fully pin-mux" pins, + "I/O processor pins" and "digital GPIO" pins. + + The device node of pin controller of Sunplus SP7021 has following + properties. + +properties: + compatible: + const: sunplus,sp7021-pctl + + gpio-controller: true + + '#gpio-cells': + const: 2 + + reg: + items: + - description: the MOON2 registers + - description: the GPIOXT registers + - description: the FIRST registers + - description: the MOON1 registers + + reg-names: + items: + - const: moon2 + - const: gpioxt + - const: first + - const: moon1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + +patternProperties: + '-pins$': + type: object + description: | + A pinctrl node should contain at least one subnodes representing the + pins or function-pins group available on the machine. Each subnode + will list the pins it needs, and how they should be configured. + + Pinctrl node's client devices use subnodes for desired pin + configuration. Client device subnodes use below standard properties. + $ref: pinmux-node.yaml# + + properties: + sunplus,pins: + description: | + Define 'sunplus,pins' which are used by pinctrl node's client + device. + + It consists of one or more integers which represents the config + setting for corresponding pin. Each integer defines a individual + pin in which: + + Bit 32~24: defines GPIO number. Its range is 0 ~ 98. + Bit 23~16: defines types: (1) fully pin-mux pins + (2) IO processor pins + (3) digital GPIO pins + Bit 15~8: defines pins of peripherals (which are defined in + 'include/dt-binging/pinctrl/sppctl.h'). + Bit 7~0: defines types or initial-state of digital GPIO pins. + + Please use macro SPPCTL_IOPAD to define the integers for pins. + + $ref: /schemas/types.yaml#/definitions/uint32-array + + function: + description: | + Define pin-function which is used by pinctrl node's client device. + The name should be one of string in the following enumeration. + $ref: "/schemas/types.yaml#/definitions/string" + enum: [ SPI_FLASH, SPI_FLASH_4BIT, SPI_NAND, CARD0_EMMC, SD_CARD, + UA0, FPGA_IFX, HDMI_TX, LCDIF, USB0_OTG, USB1_OTG ] + + groups: + description: | + Define pin-group in a specified pin-function. + The name should be one of string in the following enumeration. + $ref: "/schemas/types.yaml#/definitions/string" + enum: [ SPI_FLASH1, SPI_FLASH2, SPI_FLASH_4BIT1, SPI_FLASH_4BIT2, + SPI_NAND, CARD0_EMMC, SD_CARD, UA0, FPGA_IFX, HDMI_TX1, + HDMI_TX2, HDMI_TX3, LCDIF, USB0_OTG, USB1_OTG ] + + sunplus,zerofunc: + description: | + This is a vendor specific property. It is used to disable pins + which are not used by pinctrl node's client device. + Some pins may be enabled by boot-loader. We can use this + property to disable them. + $ref: /schemas/types.yaml#/definitions/uint32-array + + additionalProperties: false + + allOf: + - if: + properties: + function: + enum: + - SPI_FLASH + then: + properties: + groups: + enum: + - SPI_FLASH1 + - SPI_FLASH2 + - if: + properties: + function: + enum: + - SPI_FLASH_4BIT + then: + properties: + groups: + enum: + - SPI_FLASH_4BIT1 + - SPI_FLASH_4BIT2 + - if: + properties: + function: + enum: + - SPI_NAND + then: + properties: + groups: + enum: + - SPI_NAND + - if: + properties: + function: + enum: + - CARD0_EMMC + then: + properties: + groups: + enum: + - CARD0_EMMC + - if: + properties: + function: + enum: + - SD_CARD + then: + properties: + groups: + enum: + - SD_CARD + - if: + properties: + function: + enum: + - UA0 + then: + properties: + groups: + enum: + - UA0 + - if: + properties: + function: + enum: + - FPGA_IFX + then: + properties: + groups: + enum: + - FPGA_IFX + - if: + properties: + function: + enum: + - HDMI_TX + then: + properties: + groups: + enum: + - HDMI_TX1 + - HDMI_TX2 + - HDMI_TX3 + - if: + properties: + function: + enum: + - LCDIF + then: + properties: + groups: + enum: + - LCDIF + - if: + properties: + function: + enum: + - USB0_OTG + then: + properties: + groups: + enum: + - USB0_OTG + - if: + properties: + function: + enum: + - USB1_OTG + then: + properties: + groups: + enum: + - USB1_OTG + +required: + - compatible + - reg + - reg-names + - "#gpio-cells" + - gpio-controller + - clocks + - resets + +additionalProperties: false + +allOf: + - $ref: "pinctrl.yaml#" + +examples: + - | + #include <dt-bindings/pinctrl/sppctl-sp7021.h> + + pinctrl@9c000100 { + compatible = "sunplus,sp7021-pctl"; + reg = <0x9c000100 0x100>, <0x9c000300 0x100>, + <0x9c0032e4 0x1c>, <0x9c000080 0x20>; + reg-names = "moon2", "gpioxt", "first", "moon1"; + gpio-controller; + #gpio-cells = <2>; + clocks = <&clkc 0x83>; + resets = <&rstc 0x73>; + + uart0-pins { + function = "UA0"; + groups = "UA0"; + }; + + spinand0-pins { + function = "SPI_NAND"; + groups = "SPI_NAND"; + }; + + uart1-pins { + sunplus,pins = < + SPPCTL_IOPAD(11, SPPCTL_PCTL_G_PMUX, MUXF_UA1_TX, 0) + SPPCTL_IOPAD(10, SPPCTL_PCTL_G_PMUX, MUXF_UA1_RX, 0) + >; + }; + + uart2-pins { + sunplus,pins = < + SPPCTL_IOPAD(20, SPPCTL_PCTL_G_PMUX, MUXF_UA1_TX, 0) + SPPCTL_IOPAD(21, SPPCTL_PCTL_G_PMUX, MUXF_UA1_RX, 0) + SPPCTL_IOPAD(22, SPPCTL_PCTL_G_PMUX, MUXF_UA1_RTS, 0) + SPPCTL_IOPAD(23, SPPCTL_PCTL_G_PMUX, MUXF_UA1_CTS, 0) + >; + }; + + emmc-pins { + function = "CARD0_EMMC"; + groups = "CARD0_EMMC"; + }; + + sdcard-pins { + function = "SD_CARD"; + groups = "SD_CARD"; + sunplus,pins = < SPPCTL_IOPAD(91, SPPCTL_PCTL_G_GPIO, 0, 0) >; + }; + + hdmi_A_tx1-pins { + function = "HDMI_TX"; + groups = "HDMI_TX1"; + }; + hdmi_A_tx2-pins { + function = "HDMI_TX"; + groups = "HDMI_TX2"; + }; + hdmi_A_tx3-pins { + function = "HDMI_TX"; + groups = "HDMI_TX3"; + }; + + ethernet-pins { + sunplus,pins = < + SPPCTL_IOPAD(49,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_CLK_OUT,0) + SPPCTL_IOPAD(44,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_MAC_SMI_MDC,0) + SPPCTL_IOPAD(43,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_MAC_SMI_MDIO,0) + SPPCTL_IOPAD(52,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXEN,0) + SPPCTL_IOPAD(50,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXD0,0) + SPPCTL_IOPAD(51,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXD1,0) + SPPCTL_IOPAD(46,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_CRSDV,0) + SPPCTL_IOPAD(47,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXD0,0) + SPPCTL_IOPAD(48,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXD1,0) + >; + sunplus,zerofunc = < + MUXF_L2SW_LED_FLASH0 + MUXF_L2SW_LED_ON0 + MUXF_L2SW_P0_MAC_RMII_RXER + >; + }; + }; +... diff --git a/Documentation/devicetree/bindings/pinctrl/toshiba,visconti-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/toshiba,visconti-pinctrl.yaml index 9f1dab0c2430..98b4663f9766 100644 --- a/Documentation/devicetree/bindings/pinctrl/toshiba,visconti-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/toshiba,visconti-pinctrl.yaml @@ -20,6 +20,9 @@ properties: reg: maxItems: 1 +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg @@ -33,6 +36,7 @@ patternProperties: pins it needs, and how they should be configured, with regard to muxer configuration, pullups, drive strength. $ref: "pinmux-node.yaml" + additionalProperties: false properties: function: @@ -80,7 +84,7 @@ examples: #address-cells = <2>; #size-cells = <2>; - pmux: pmux@24190000 { + pmux: pinmux@24190000 { compatible = "toshiba,tmpv7708-pinctrl"; reg = <0 0x24190000 0 0x10000>; diff --git a/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.yaml index ac97dbf6998e..cfd0cc549a7b 100644 --- a/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.yaml @@ -167,6 +167,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: "pinctrl.yaml#" + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.yaml index 8ef0d07d35fe..2722dc7bb03d 100644 --- a/Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/xlnx,zynqmp-pinctrl.yaml @@ -290,6 +290,9 @@ patternProperties: additionalProperties: false +allOf: + - $ref: pinctrl.yaml# + required: - compatible |