diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb/mediatek,mtu3.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/mediatek,mtu3.txt | 34 |
1 files changed, 20 insertions, 14 deletions
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt index 49f54767cd21..d589a1ef96a1 100644 --- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt +++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt @@ -14,9 +14,9 @@ Required properties: - vusb33-supply : regulator of USB avdd3.3v - clocks : a list of phandle + clock-specifier pairs, one for each entry in clock-names - - clock-names : must contain "sys_ck" and "ref_ck" for clock of controller; - "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are - depends on "mediatek,enable-wakeup" + - clock-names : must contain "sys_ck" for clock of controller, + the following clocks are optional: + "ref_ck", "mcu_ck" and "dam_ck"; - phys : a list of phandle + phy specifier pairs - dr_mode : should be one of "host", "peripheral" or "otg", refer to usb/generic.txt @@ -30,9 +30,10 @@ Optional properties: when supports dual-role mode. - vbus-supply : reference to the VBUS regulator, needed when supports dual-role mode. - - pinctl-names : a pinctrl state named "default" must be defined, - "id_float" and "id_ground" are optinal which depends on - "mediatek,enable-manual-drd" + - pinctrl-names : a pinctrl state named "default" is optional, and need be + defined if auto drd switch is enabled, that means the property dr_mode + is set as "otg", and meanwhile the property "mediatek,enable-manual-drd" + is not set. - pinctrl-0 : pin control group See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -41,9 +42,16 @@ Optional properties: - enable-manual-drd : supports manual dual-role switch via debugfs; usually used when receptacle is TYPE-A and also wants to support dual-role mode. - - mediatek,enable-wakeup : supports ip sleep wakeup used by host mode - - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup - control register, it depends on "mediatek,enable-wakeup". + - wakeup-source: enable USB remote wakeup of host mode. + - mediatek,syscon-wakeup : phandle to syscon used to access the register + of the USB wakeup glue layer between SSUSB and SPM; it depends on + "wakeup-source", and has two arguments: + - the first one : register base address of the glue layer in syscon; + - the second one : hardware version of the glue layer + - 1 : used by mt8173 etc + - 2 : used by mt2712 etc + - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, + bit1 for u3port1, ... etc; Sub-nodes: The xhci should be added as subnode to mtu3 as shown in the following example @@ -63,15 +71,13 @@ ssusb: usb@11271000 { clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, <&pericfg CLK_PERI_USB0>, <&pericfg CLK_PERI_USB1>; - clock-names = "sys_ck", "ref_ck", - "wakeup_deb_p0", - "wakeup_deb_p1"; + clock-names = "sys_ck", "ref_ck"; vusb33-supply = <&mt6397_vusb_reg>; vbus-supply = <&usb_p0_vbus>; extcon = <&extcon_usb>; dr_mode = "otg"; - mediatek,enable-wakeup; - mediatek,syscon-wakeup = <&pericfg>; + wakeup-source; + mediatek,syscon-wakeup = <&pericfg 0x400 1>; #address-cells = <2>; #size-cells = <2>; ranges; |