| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In order to automate the verification of DT nodes convert fsl-fec.txt to
fsl,fec.yaml, and pass binding check with below command.
$ make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/fsl,fec.yaml
DTEX Documentation/devicetree/bindings/net/fsl,fec.example.dts
DTC Documentation/devicetree/bindings/net/fsl,fec.example.dt.yaml
CHECK Documentation/devicetree/bindings/net/fsl,fec.example.dt.yaml
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- rename the 'gpr' property string to 'fsl,stop-mode'.
- Update the property to define gpr register offset and
bit in DT, since different instance have different gpr bit.
v2:
* rename 'gpr' property string to 'fsl,stop-mode'.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MDIO busses typically operate at 2.5MHz. However many devices can
operate at faster speeds. This then allows more MDIO transactions per
second, useful for Ethernet switch statistics, or Ethernet PHY TDR
data. Allow the bus speed to be configured, using the standard
"clock-frequency" property, which i2c busses use to indicate the bus
speed. Before using this property, ensure all devices on the bus do
actually support the requested clock speed.
Suggested-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This property allows the gpr register bit to be defined
for wake on lan support.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fec's gpio phy reset properties have been deprecated.
Update the dt-bindings documentation to explicitly mark
them as such, and provide a short description of the
recommended alternative.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The GPIO polarity passed to phy-reset-gpio is ignored by the FEC
driver and it is assumed to be active low.
It can be active high only when the 'phy-reset-active-high' property
is present.
The current examples pass active high polarity and work fine, but
in order to improve the documentation make it explicit what the real
polarity is.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is better for code locality and should slightly
speed up normal interrupts.
This also allows PPS clock output to start working for
i.mx7. This is because i.mx7 was already using the limit
of 3 interrupts, and needed another.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHY require to wait for a bit after the reset GPIO has been
toggled. This adds support for the DT property `phy-reset-post-delay`
which gives the delay in milliseconds to wait after reset.
If the DT property is not given, no delay is observed. Post reset delay
greater than 1000ms are invalid.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The i.MX6 Q/DL has an erratum (ERR006687) that prevents the FEC from
waking the CPUs when they are in wait(unclocked) state. As the hardware
workaround isn't applicable to all boards, disable the deeper idle state
when the workaround isn't present and the FEC is in use.
This allows to safely run a kernel with CPUidle enabled on all i.MX6
boards.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net> (for network changes)
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
is actually "active high". Thanks for Troy Kisky for pointing
that out.
Since the patch is in linux-next, this patch is incremental and doesn't
replace the original patch.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need that for a custom hardware that needs the reverse reset
sequence.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support for Wake-on-LAN using Magic Packet. ENET IP supports sleep mode
in low power status, when system enter suspend status, Magic packet can
wake up system even if all SOC clocks are gate. The patch doing below things:
- flagging the device as a wakeup source for the system, as well as
its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- add standard ethtool WOL interface
- enable the ENET interrupt to wake us
Tested on i.MX6q/dl sabresd, sabreauto boards, i.MX6SX arm2 boards.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch update fec devicetree binding doc that add Optional
properties "fsl,num-tx-queues" and "fsl,num-rx-queues".
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for specifying the phy to be used with the fec in the
devicetree using the standard phy-handle property and also supports
fixed-link.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is an attempt to gather the Ethernet related bindings in one file,
like it's done in the MMC and some other subsystems. It should save some of
the trouble of documenting several properties over and over in each binding
document, instead only making reference to the main file.
I have used the Embedded Power Architecture(TM) Platform Requirements (ePAPR)
standard as a base for the properties description, also documenting some ad-hoc
properties that have been introduced over time despite having direct analogs in
ePAPR.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy-supply is an optional property of the fec driver, so add it to the binding
documentation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Conflicts:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
|
|
Different boards may require different phy reset duration. Add property
phy-reset-duration for device tree probe, so that the boards that need
a longer reset duration can specify it in their device tree.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy-reset-gpios is an optional property for fec device tree boot.
Change the binding document to match the driver code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix gpio number assignment, so that it can match the number stated in the comment.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
It has been pointed out by device tree maintainer for several times
that the generic names 'serial' and 'ethernet' should be used for
those devices per ePAPR. Renames imx uart and fec device tree nodes
to stop them being bad examples.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
It adds device tree probe support for fec driver.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
|
Joakim Zhang
Fugang Duan
Andrew Lunn
Martin Fuzzey
Sven Van Asbroeck
Fabio Estevam
Troy Kisky
Quentin Schulz
Lucas Stach
Bernhard Walle
Nimrod Andy
Frank Li
Uwe Kleine-König
Sergei Shtylyov
Fabio Estevam
David S. Miller
Shawn Guo