| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add DT support for at91rm9200_wdt.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
this patchset add the timeout-sec property to the following drivers:
orion_wdt, pnx4008_wdt, s3c2410_wdt and at91sam9_wdt.
The at91sam9_wdt is tested on evk-pr3,
the other drivers are compile tested only.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add support for watchdog drivers to initialize/set the timeout field
of the watchdog_device structure. The timeout field is initialised
either with the module timeout parameter value (if valid) or with the
timeout-sec dt property (if valid). If both are invalid the initial
value is unchanged.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Pull ARM SoC mvebu platform changes from Olof Johansson:
"This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
- More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers
here, ethernet and PCI still remain.
- SMP support for mvebu is improved with support for the local
interrupt controller.
- The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the
patches in his tree that all of the patches in this branch are based
on, which caused merge conflicts between the new and old versions of
those patches.
To work around the merge conflicts, this branch rebases all patches on
top of the respective MMC patches that did get merged into 3.9. The
patches are all identical to the versions that were part of
linux-next, but have a new commit date."
* tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (90 commits)
arm: mvebu: enable the SD card slot on Armada 370 Reference Design board
ARM: kirkwood: topkick: init mvsdio via DT
ARM: kirkwood: nsa310: convert to pinctrl
ARM: Kirkwood: topkick: Enable i2c bus.
ARM: kirkwood: topkick: convert to pinctrl
ARM: dove: convert serial DT nodes to clocks property
arm: mvebu: Add SPI flash on Armada 370 DB board
arm: mvebu: Add SPI flash on Armada XP-DB board
arm: mvebu: Add SPI flash on Armada XP-GP board
arm: mvebu: Add support for SPI controller in Armada 370/XP
clocksource: update and move armada-370-xp-timer documentation to timer directory
arm: mvebu: update DT to support local timers
ARM: Dove: convert usb host controller to DT
arm: mvebu: Enable USB controllers on Armada 370/XP boards
arm: mvebu: Add support for USB host controllers in Armada 370/XP
arm: mvebu: add button for OpenBlocks AX3-4
ARM: Kirkwood: Convert NS2 to gpio-poweroff.
ARM: Kirkwood: Convert NSA310 I2C to device tree
ARM: Kirkwood: Convert NSA310 to use gpio-poweroff driver
ARM: Kirkwood: Convert NSA310 to DT based regulators.
...
|
|
Pull ARM SoC i.MX DT changes from Olof Johansson:
"This branch contains of devicetree changes for the Freescale i.MX
platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process
since every line of the file is touched.
On top of that are a handful of the regular changes; enabling more
boards as DT-based instead of legacy board files (mx25pdk), enabling
another driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other
platforms in the future."
* tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: dts: add dtsi for imx6q and imx6dl
ARM: dts: rename imx6q.dtsi to imx6qdl.dtsi
ARM: dts: i.MX6: Add regulator delay support
ARM: dts: Add device tree entry for onewire master on i.MX53
ARM: i.MX53: Add clocks for i.mx53 onewire master.
W1: Add device tree support to MXC onewire master.
ARM: imx: enable imx6q-cpufreq support
ARM: dts: Add apf51 basic support
ARM i.MX6: change mxs usbphy clock usage
ARM: dts: imx6q: Remove silicon version from SDMA firmware
ARM i.MX53: dts: add oftree for MBa53 baseboard
ARM i.MX53: add dts for the TQ tqma53 module
ARM: dts: imx53: pinctrl update
ARM i.MX51 babbage: Add keypad support
ARM: dts: imx: Add imx51 KPP entry
ARM: dts: imx25-karo-tx25: Put status entry in the end
ARM: mx25pdk: Add device tree support
ARM: dts: imx: use nodes label in board dts
ARM: dts: add missing imx dtb targets
ARM: boot: dts: Add an entry for imx27-pdk.dtb
...
|
|
Pull thermal management updates from Zhang Rui:
"Highlights:
- introduction of Dove thermal sensor driver.
- introduction of Kirkwood thermal sensor driver.
- introduction of intel_powerclamp thermal cooling device driver.
- add interrupt and DT support for rcar thermal driver.
- add thermal emulation support which allows platform thermal driver
to do software/hardware emulation for thermal issues."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
thermal: rcar: remove __devinitconst
thermal: return an error on failure to register thermal class
Thermal: rename thermal governor Kconfig option to avoid generic naming
thermal: exynos: Use the new thermal trend type for quick cooling action.
Thermal: exynos: Add support for temperature falling interrupt.
Thermal: Dove: Add Themal sensor support for Dove.
thermal: Add support for the thermal sensor on Kirkwood SoCs
thermal: rcar: add Device Tree support
thermal: rcar: remove machine_power_off() from rcar_thermal_notify()
thermal: rcar: add interrupt support
thermal: rcar: add read/write functions for common/priv data
thermal: rcar: multi channel support
thermal: rcar: use mutex lock instead of spin lock
thermal: rcar: enable CPCTL to use hardware TSC deciding
thermal: rcar: use parenthesis on macro
Thermal: fix a build warning when CONFIG_THERMAL_EMULATION cleared
Thermal: fix a wrong comment
thermal: sysfs: Add a new sysfs node emul_temp for thermal emulation
PM: intel_powerclamp: off by one in start_power_clamp()
thermal: exynos: Miscellaneous fixes to support falling threshold interrupt
...
|
|
Pull dma-buf framework updates from Sumit Semwal:
"Refcounting implemented for vmap in core dma-buf"
* tag 'tag-for-linus-3.9' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf:
CHROMIUM: dma-buf: restore args on failure of dma_buf_mmap
dma-buf: implement vmap refcounting in the interface logic
|
|
Pull block IO core bits from Jens Axboe:
"Below are the core block IO bits for 3.9. It was delayed a few days
since my workstation kept crashing every 2-8h after pulling it into
current -git, but turns out it is a bug in the new pstate code (divide
by zero, will report separately). In any case, it contains:
- The big cfq/blkcg update from Tejun and and Vivek.
- Additional block and writeback tracepoints from Tejun.
- Improvement of the should sort (based on queues) logic in the plug
flushing.
- _io() variants of the wait_for_completion() interface, using
io_schedule() instead of schedule() to contribute to io wait
properly.
- Various little fixes.
You'll get two trivial merge conflicts, which should be easy enough to
fix up"
Fix up the trivial conflicts due to hlist traversal cleanups (commit
b67bfe0d42ca: "hlist: drop the node parameter from iterators").
* 'for-3.9/core' of git://git.kernel.dk/linux-block: (39 commits)
block: remove redundant check to bd_openers()
block: use i_size_write() in bd_set_size()
cfq: fix lock imbalance with failed allocations
drivers/block/swim3.c: fix null pointer dereference
block: don't select PERCPU_RWSEM
block: account iowait time when waiting for completion of IO request
sched: add wait_for_completion_io[_timeout]
writeback: add more tracepoints
block: add block_{touch|dirty}_buffer tracepoint
buffer: make touch_buffer() an exported function
block: add @req to bio_{front|back}_merge tracepoints
block: add missing block_bio_complete() tracepoint
block: Remove should_sort judgement when flush blk_plug
block,elevator: use new hashtable implementation
cfq-iosched: add hierarchical cfq_group statistics
cfq-iosched: collect stats from dead cfqgs
cfq-iosched: separate out cfqg_stats_reset() from cfq_pd_reset_stats()
blkcg: make blkcg_print_blkgs() grab q locks instead of blkcg lock
block: RCU free request_queue
blkcg: implement blkg_[rw]stat_recursive_sum() and blkg_[rw]stat_merge()
...
|
|
Timer driver for Armada 370 and Armada XP have gained local timers
support. So it needs new resources information regarding the IRQs
and the registers.
Also move the documentation in the new and more accurate directory
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Merge third patch-bumb from Andrew Morton:
"This wraps me up for -rc1.
- Lots of misc stuff and things which were deferred/missed from
patchbombings 1 & 2.
- ocfs2 things
- lib/scatterlist
- hfsplus
- fatfs
- documentation
- signals
- procfs
- lockdep
- coredump
- seqfile core
- kexec
- Tejun's large IDR tree reworkings
- ipmi
- partitions
- nbd
- random() things
- kfifo
- tools/testing/selftests updates
- Sasha's large and pointless hlist cleanup"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (163 commits)
hlist: drop the node parameter from iterators
kcmp: make it depend on CHECKPOINT_RESTORE
selftests: add a simple doc
tools/testing/selftests/Makefile: rearrange targets
selftests/efivarfs: add create-read test
selftests/efivarfs: add empty file creation test
selftests: add tests for efivarfs
kfifo: fix kfifo_alloc() and kfifo_init()
kfifo: move kfifo.c from kernel/ to lib/
arch Kconfig: centralise CONFIG_ARCH_NO_VIRT_TO_BUS
w1: add support for DS2413 Dual Channel Addressable Switch
memstick: move the dereference below the NULL test
drivers/pps/clients/pps-gpio.c: use devm_kzalloc
Documentation/DMA-API-HOWTO.txt: fix typo
include/linux/eventfd.h: fix incorrect filename is a comment
mtd: mtd_stresstest: use prandom_bytes()
mtd: mtd_subpagetest: convert to use prandom library
mtd: mtd_speedtest: use prandom_bytes
mtd: mtd_pagetest: convert to use prandom library
mtd: mtd_oobtest: convert to use prandom library
...
|
|
Noted by Jesper
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Documentation/blockdev/nbd.txt contained some documentation which was
horribly outdated and probably still dates from the original patch that
added NBD support to the kernel.
This patch removes the useless and outdated bits. The tools on nbd.sf.net
are fully documented in manpages, which is where documentation for the
non-kernel bits should live.
Additionally, add a reference to the MAINTAINERS file for the nbd-general
mailinglist that is used for discussion of the userland tools and the
kernel module already.
Signed-off-by: Wouter Verhelst <w@uter.be>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add try... parameters to disable pci and platform (openfirmware) device
scanning for IPMI. Also add docs for all the try... parameters.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Warren Turkal <wt@ooyala.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull more x86 fixes from Peter Anvin:
"Additional x86 fixes. Three of these patches are pure documentation,
two are pretty trivial; the remaining one fixes boot problems on some
non-BIOS machines."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Make sure we can boot in the case the BDA contains pure garbage
x86, efi: Mark disable_runtime as __initdata
x86, doc: Fix incorrect comment about 64-bit code segment descriptors
doc, kernel-parameters: Document 'console=hvc<n>'
doc, xen: Mention 'earlyprintk=xen' in the documentation.
ACPI: Overriding ACPI tables via initrd only works with an initrd and on X86
|
|
Pull kconfig changes from Michal Marek:
"I forgot to send a pull request in time for the v3.8-rc1 merge window,
so the list is a bit longer this time:
- menuconfig enables extended colors in ncurses if the wide-character
version is used.
- CONFIG_ prefix can be specified in the environment to make life
easier for people using kconfig multiple times in a single tree (no
functional change in the kernel kconfig usage).
- kconfig aborts on OOM.
- inputboxes in menuconfig allow to move the cursor.
- menuconfig has Save/Load buttons now.
- xconfig build fix with new g++ and Qt3.
- nconfig color scheme fix and help text update.
- make oldconfig prints newlines when output is redirected.
- some other minor fixes."
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Fix missing '\n' for NEW symbols in yes "" | make oldconfig >conf.new
kconfig: nconf: rewrite labels of function keys line
kconfig: nconf: rewrite help texts
kconfig: fix a compiliation error when using make xconfig
nconf: function keys line, change background color for better readability
menuconfig: Get rid of the top-level entries for "Load an Alternate/Save an Alternate"
menuconfig: Add Save/Load buttons
kconfig:lxdialog: remove duplicate code
menuconfig:inputbox: support navigate input position
kconfig: document use of CONFIG_ environment variable
scripts/kconfig: ensure we use proper CONFIG_ prefix
merge_config.sh: Add option to specify output dir
Revert "kconfig-language: add to hints"
kconfig: Regenerate lexer
kconfig: Fix malloc handling in conf tools
kconfig: get CONFIG_ prefix from the environment
kconfig: add a function to get the CONFIG_ prefix
kconfig: remove CONFIG_ from string constants
menuconfig: fix extended colors ncurses support
|
|
Pull misc non-critical kbuild changes from Michal Marek:
- Fix for make TAGS
- Fix for make rpm
- Some new coccinelle semantic patches
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/coccinelle: find constant additions that could be bit ors
coccicheck: Allow to show the executed command line
coccicheck: Allow the user to give a V= (verbose) argument
scripts/coccinelle/misc/memcpy-assign.cocci: Replace memcpy with struct assignment
kbuild: clear KBUILD_SRC when calling 'make' in RPM spec
scripts/coccinelle/misc/semicolon.cocci: Add unneeded semicolon test
scripts/tags.sh: Fix regex syntax for etags
|
|
All drivers which implement this need to have some sort of refcount to
allow concurrent vmap usage. Hence implement this in the dma-buf core.
To protect against concurrent calls we need a lock, which potentially
causes new funny locking inversions. But this shouldn't be a problem
for exporters with statically allocated backing storage, and more
dynamic drivers have decent issues already anyway.
Inspired by some refactoring patches from Aaron Plattner, who
implemented the same idea, but only for drm/prime drivers.
v2: Check in dma_buf_release that no dangling vmaps are left.
Suggested by Aaron Plattner. We might want to do similar checks for
attachments, but that's for another patch. Also fix up ERR_PTR return
for vmap.
v3: Check whether the passed-in vmap address matches with the cached
one for vunmap. Eventually we might want to remove that parameter -
compared to the kmap functions there's no need for the vaddr for
unmapping. Suggested by Chris Wilson.
v4: Fix a brown-paper-bag bug spotted by Aaron Plattner.
Cc: Aaron Plattner <aplattner@nvidia.com>
Reviewed-by: Aaron Plattner <aplattner@nvidia.com>
Tested-by: Aaron Plattner <aplattner@nvidia.com>
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
|
|
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
|
|
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Intel ismt & Broadcom bcm2835
- a number of drivers got support for more variants and mostly got
cleaned up on the way (sis630, i801, at91, tegra, designware)
- i2c got rid of all *_set_drvdata(..., NULL) on remove/probe failure
- removed the i2c_smbus_process_call from the core since there are no
users
- mxs can now switch between PIO and DMA depending on the message
size and the bus speed can now be arbitrary
In addition, there is the usual bunch of fixes, cleanups, devm_*
conversions, etc"
Fixed conflict (and buggy devm_* conversion) in i2c-s3c2410.c
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (39 commits)
i2c: Remove unneeded xxx_set_drvdata(..., NULL) calls
i2c: pxa: remove incorrect __exit annotations
i2c: ocores: Fix pointer to integer cast warning
i2c: tegra: remove warning dump if timeout happen in transfer
i2c: fix i2c-ismt.c printk format warning
i2c: i801: Add Device IDs for Intel Wellsburg PCH
i2c: add bcm2835 driver
i2c: ismt: Add Seth and Myself as maintainers
i2c: sis630: checkpatch cleanup
i2c: sis630: display unsigned hex
i2c: sis630: use hex to constants for SMBus commands
i2c: sis630: fix behavior after collision
i2c: sis630: clear sticky bits
i2c: sis630: Add SIS964 support
i2c: isch: Add module parameter for backbone clock rate if divider is unset
i2c: at91: fix unsed variable warning when building with !CONFIG_OF
i2c: Adding support for Intel iSMT SMBus 2.0 host controller
i2c: sh_mobile: don't send a stop condition by default inside transfers
i2c: sh_mobile: eliminate an open-coded "goto" loop
i2c: sh_mobile: fix timeout error handling
...
|
|
Pull PWM changes from Thierry Reding:
"A new driver has been added to support the PWM mode of the timer
counter blocks found on Atmel AT91 SoCs. The VT8500 driver now
supports changing the PWM signal polarity and the TI drivers (EHRPWM
and ECAP) gained suspend and resume functionality.
User drivers can now query the core for whether access to a PWM device
will sleep (if the PWM chip is on a slow bus such as I2C or SPI).
The pwm-backlight driver now handles the backlight BL_CORE_FBBLANK
state in addition to the FB layer's blanking states.
To round things off, a few fixes and cleanups are also included"
* tag 'for-3.9-rc1' of git://gitorious.org/linux-pwm/linux-pwm:
pwm: twl: Use to_twl() instead of container_of()
pwm: tegra: assume CONFIG_OF
pwm_backlight: Validate dft_brightness in main probe function
pwm: Export pwm_{set,get}_chip_data()
pwm: Make Kconfig entries more consistent
pwm: Add can_sleep property to drivers
pwm: Add pwm_can_sleep() as exported API to users
pwm-backlight: handle BL_CORE_FBBLANK state
pwm: pwm-tiecap: Low power sleep support
pwm: pwm-tiehrpwm: Low power sleep support
pwm: pwm-tiehrpwm: Update the clock handling of pwm-tiehrpwm driver
pwm: vt8500: Add polarity support
pwm: vt8500: Register write busy test performed incorrectly
pwm: atmel: add Timer Counter Block PWM driver
|
|
Pull MMC update from Chris Ball:
"MMC highlights for 3.9:
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"
* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...
|
|
Pull LED subsystem update from Bryan Wu.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (61 commits)
leds: leds-sunfire: use dev_err()/pr_err() instead of printk()
leds: 88pm860x: Add missing of_node_put()
leds: tca6507: Use of_get_child_count()
leds: leds-pwm: make it depend on PWM and not HAVE_PWM
Documentation: leds: update LP55xx family devices
leds-lp55xx: fix problem on removing LED attributes
leds-lp5521/5523: add author and copyright description
leds-lp5521/5523: use new lp55xx common header
leds-lp55xx: clean up headers
leds-lp55xx: clean up definitions
leds-lp55xx: clean up unused data and functions
leds-lp55xx: clean up _remove()
leds-lp55xx: add new function for removing device attribtues
leds-lp55xx: code refactoring on selftest function
leds-lp55xx: use common device attribute driver function
leds-lp55xx: support device specific attributes
leds-lp5523: use generic firmware interface
leds-lp5521: use generic firmware interface
leds-lp55xx: support firmware interface
leds-lp55xx: add new lp55xx_register_sysfs() for the firmware interface
...
|
|
Pull slave-dmaengine updates from Vinod Koul:
"This is fairly big pull by my standards as I had missed last merge
window. So we have the support for device tree for slave-dmaengine,
large updates to dw_dmac driver from Andy for reusing on different
architectures. Along with this we have fixes on bunch of the drivers"
Fix up trivial conflicts, usually due to #include line movement next to
each other.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (111 commits)
Revert "ARM: SPEAr13xx: Pass DW DMAC platform data from DT"
ARM: dts: pl330: Add #dma-cells for generic dma binding support
DMA: PL330: Register the DMA controller with the generic DMA helpers
DMA: PL330: Add xlate function
DMA: PL330: Add new pl330 filter for DT case.
dma: tegra20-apb-dma: remove unnecessary assignment
edma: do not waste memory for dma_mask
dma: coh901318: set residue only if dma is in progress
dma: coh901318: avoid unbalanced locking
dmaengine.h: remove redundant else keyword
dma: of-dma: protect list write operation by spin_lock
dmaengine: ste_dma40: do not remove descriptors for cyclic transfers
dma: of-dma.c: fix memory leakage
dw_dmac: apply default dma_mask if needed
dmaengine: ioat - fix spare sparse complain
dmaengine: move drivers/of/dma.c -> drivers/dma/of-dma.c
ioatdma: fix race between updating ioat->head and IOAT_COMPLETION_PENDING
dw_dmac: add support for Lynxpoint DMA controllers
dw_dmac: return proper residue value
dw_dmac: fill individual length of descriptor
...
|
|
The following set of operations on a NFS client and server will cause
server# mkdir a
client# cd a
server# mv a a.bak
client# sleep 30 # (or whatever the dir attrcache timeout is)
client# stat .
stat: cannot stat `.': Stale NFS file handle
Obviously, we should not be getting an ESTALE error back there since the
inode still exists on the server. The problem is that the lookup code
will call d_revalidate on the dentry that "." refers to, because NFS has
FS_REVAL_DOT set.
nfs_lookup_revalidate will see that the parent directory has changed and
will try to reverify the dentry by redoing a LOOKUP. That of course
fails, so the lookup code returns ESTALE.
The problem here is that d_revalidate is really a bad fit for this case.
What we really want to know at this point is whether the inode is still
good or not, but we don't really care what name it goes by or whether
the dcache is still valid.
Add a new d_op->d_weak_revalidate operation and have complete_walk call
that instead of d_revalidate. The intent there is to allow for a
"weaker" d_revalidate that just checks to see whether the inode is still
good. This is also gives us an opportunity to kill off the FS_REVAL_DOT
special casing.
[AV: changed method name, added note in porting, fixed confusion re
having it possibly called from RCU mode (it won't be)]
Cc: NeilBrown <neilb@suse.de>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)"
* tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
PCI/ACPI: Don't cache _PRT, and don't associate them with bus numbers
PCI: Fix PCI Express Capability accessors for PCI_EXP_FLAGS
ACPI / PCI: Make pci_slot built-in only, not a module
PCI/PM: Clear state_saved during suspend
PCI: Use atomic_inc_return() rather than atomic_add_return()
PCI: Catch attempts to disable already-disabled devices
PCI: Disable Bus Master unconditionally in pci_device_shutdown()
PCI: acpiphp: Remove dead code for PCI host bridge hotplug
PCI: acpiphp: Create companion ACPI devices before creating PCI devices
PCI: Remove unused "rc" in virtfn_add_bus()
PCI: pciehp: Drop suspend/resume ENTRY messages
PCI/ASPM: Don't touch ASPM if forcibly disabled
PCI/ASPM: Deallocate upstream link state even if device is not PCIe
PCI: Document MPS parameters pci=pcie_bus_safe, pci=pcie_bus_perf, etc
PCI: Document hpiosize= and hpmemsize= resource reservation parameters
PCI: Use PCI Express Capability accessor
PCI: Introduce accessor to retrieve PCIe Capabilities Register
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
...
|
|
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d8d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
|
|
Pull user namespace and namespace infrastructure changes from Eric W Biederman:
"This set of changes starts with a few small enhnacements to the user
namespace. reboot support, allowing more arbitrary mappings, and
support for mounting devpts, ramfs, tmpfs, and mqueuefs as just the
user namespace root.
I do my best to document that if you care about limiting your
unprivileged users that when you have the user namespace support
enabled you will need to enable memory control groups.
There is a minor bug fix to prevent overflowing the stack if someone
creates way too many user namespaces.
The bulk of the changes are a continuation of the kuid/kgid push down
work through the filesystems. These changes make using uids and gids
typesafe which ensures that these filesystems are safe to use when
multiple user namespaces are in use. The filesystems converted for
3.9 are ceph, 9p, afs, ocfs2, gfs2, ncpfs, nfs, nfsd, and cifs. The
changes for these filesystems were a little more involved so I split
the changes into smaller hopefully obviously correct changes.
XFS is the only filesystem that remains. I was hoping I could get
that in this release so that user namespace support would be enabled
with an allyesconfig or an allmodconfig but it looks like the xfs
changes need another couple of days before it they are ready."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (93 commits)
cifs: Enable building with user namespaces enabled.
cifs: Convert struct cifs_ses to use a kuid_t and a kgid_t
cifs: Convert struct cifs_sb_info to use kuids and kgids
cifs: Modify struct smb_vol to use kuids and kgids
cifs: Convert struct cifsFileInfo to use a kuid
cifs: Convert struct cifs_fattr to use kuid and kgids
cifs: Convert struct tcon_link to use a kuid.
cifs: Modify struct cifs_unix_set_info_args to hold a kuid_t and a kgid_t
cifs: Convert from a kuid before printing current_fsuid
cifs: Use kuids and kgids SID to uid/gid mapping
cifs: Pass GLOBAL_ROOT_UID and GLOBAL_ROOT_GID to keyring_alloc
cifs: Use BUILD_BUG_ON to validate uids and gids are the same size
cifs: Override unmappable incoming uids and gids
nfsd: Enable building with user namespaces enabled.
nfsd: Properly compare and initialize kuids and kgids
nfsd: Store ex_anon_uid and ex_anon_gid as kuids and kgids
nfsd: Modify nfsd4_cb_sec to use kuids and kgids
nfsd: Handle kuids and kgids in the nfs4acl to posix_acl conversion
nfsd: Convert nfsxdr to use kuids and kgids
nfsd: Convert nfs3xdr to use kuids and kgids
...
|
|
Pull crypto update from Herbert Xu:
"Here is the crypto update for 3.9:
- Added accelerated implementation of crc32 using pclmulqdq.
- Added test vector for fcrypt.
- Added support for OMAP4/AM33XX cipher and hash.
- Fixed loose crypto_user input checks.
- Misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (43 commits)
crypto: user - ensure user supplied strings are nul-terminated
crypto: user - fix empty string test in report API
crypto: user - fix info leaks in report API
crypto: caam - Added property fsl,sec-era in SEC4.0 device tree binding.
crypto: use ERR_CAST
crypto: atmel-aes - adjust duplicate test
crypto: crc32-pclmul - Kill warning on x86-32
crypto: x86/twofish - assembler clean-ups: use ENTRY/ENDPROC, localize jump labels
crypto: x86/sha1 - assembler clean-ups: use ENTRY/ENDPROC
crypto: x86/serpent - use ENTRY/ENDPROC for assember functions and localize jump targets
crypto: x86/salsa20 - assembler cleanup, use ENTRY/ENDPROC for assember functions and rename ECRYPT_* to salsa20_*
crypto: x86/ghash - assembler clean-up: use ENDPROC at end of assember functions
crypto: x86/crc32c - assembler clean-up: use ENTRY/ENDPROC
crypto: cast6-avx: use ENTRY()/ENDPROC() for assembler functions
crypto: cast5-avx: use ENTRY()/ENDPROC() for assembler functions and localize jump targets
crypto: camellia-x86_64/aes-ni: use ENTRY()/ENDPROC() for assembler functions and localize jump targets
crypto: blowfish-x86_64: use ENTRY()/ENDPROC() for assembler functions and localize jump targets
crypto: aesni-intel - add ENDPROC statements for assembler functions
crypto: x86/aes - assembler clean-ups: use ENTRY/ENDPROC, localize jump targets
crypto: testmgr - add test vector for fcrypt
...
|
|
Both the PowerPC hypervisor and Xen hypervisor can utilize the
hvc driver.
Cc: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1361825650-14031-3-git-send-email-konrad.wilk@oracle.com
Cc: <stable@vger.kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
The earlyprintk for Xen PV guests utilizes a simple hypercall
(console_io) to provide output to Xen emergency console.
Note that the Xen hypervisor should be booted with 'loglevel=all'
to output said information.
Reported-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1361825650-14031-2-git-send-email-konrad.wilk@oracle.com
Cc: <stable@vger.kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
There is one kconfig fix in the rc-fixes branch that I forgot to submit
for 3.8, so let's add it to the kconfig branch for 3.9-rc1.
|
|
Pull MFS updates from Samuel Ortiz:
"This is the MFD pull request for the 3.9 merge window.
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data
consolidation, OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee
Jones. In particular, the debugfs and the sysct interfaces got
extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the
twl-core driver, with a much needed module id lookup code
improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the
palmas GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra
and Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and
ab9540 based devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to
Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a
better card detection code path and now also supports the RTS5227
chipset, thanks to Wei Wang and Roger Tseng."
* tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (109 commits)
mfd: lpc_ich: Use devres API to allocate private data
mfd: lpc_ich: Add Device IDs for Intel Wellsburg PCH
mfd: lpc_sch: Accomodate partial population of the MFD devices
mfd: da9052-i2c: Staticize da9052_i2c_fix()
mfd: syscon: Fix sparse warning
mfd: twl-core: Fix kernel panic on boot
mfd: rtsx: Fix issue that booting OS with SD card inserted
mfd: ab8500: Fix compile error
mfd: Add missing GENERIC_HARDIRQS dependecies
Documentation: Add docs for max8925 dt
mfd: max8925: Add dts
mfd: max8925: Support dt for backlight
mfd: max8925: Fix onkey driver irq base
mfd: max8925: Fix mfd device register failure
mfd: max8925: Add irqdomain for dt
mfd: vexpress: Allow vexpress-sysreg to self-initialise
mfd: rtsx: Support RTS5227
mfd: rtsx: Implement driving adjustment to device-dependent callbacks
mfd: vexpress: Add pseudo-GPIO based LEDs
mfd: ab8500: Rename ab8500 to abx500 for hwmon driver
...
|
|
Pull media updates from Mauro Carvalho Chehab:
- Some cleanups at V4L2 documentation
- new drivers: ts2020 frontend, ov9650 sensor, s5c73m3 sensor,
sh-mobile veu mem2mem driver, radio-ma901, davinci_vpfe staging
driver
- Lots of missing MAINTAINERS entries added
- several em28xx driver improvements, including its conversion to
videobuf2
- several fixups on drivers to make them to better comply with the API
- DVB core: add support for DVBv5 stats, allowing the implementation of
statistics for new standards like ISDB
- mb86a20s: add statistics to the driver
- lots of new board additions, cleanups, and driver improvements.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (596 commits)
[media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
[media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
[media] em28xx: add usb id for terratec h5 rev. 3
[media] media: rc: gpio-ir-recv: add support for device tree parsing
[media] mceusb: move check earlier to make smatch happy
[media] radio-si470x doc: add info about v4l2-ctl and sox+alsa
[media] staging: media: Remove unnecessary OOM messages
[media] sh_vou: Use vou_dev instead of vou_file wherever possible
[media] sh_vou: Use video_drvdata()
[media] drivers/media/platform/soc_camera/pxa_camera.c: use devm_ functions
[media] mt9t112: mt9t111 format set up differs from mt9t112
[media] sh-mobile-ceu-camera: fix SHARPNESS control default
Revert "[media] fc0011: Return early, if the frequency is already tuned"
[media] cx18/ivtv: fix regression: remove __init from a non-init function
[media] em28xx: fix analog streaming with USB bulk transfers
[media] stv0900: remove unnecessary null pointer check
[media] fc0011: Return early, if the frequency is already tuned
[media] fc0011: Add some sanity checks and cleanups
[media] fc0011: Fix xin value clamping
Revert "[media] [PATH,1/2] mxl5007 move reset to attach"
...
|
|
Pull KVM updates from Marcelo Tosatti:
"KVM updates for the 3.9 merge window, including x86 real mode
emulation fixes, stronger memory slot interface restrictions, mmu_lock
spinlock hold time reduction, improved handling of large page faults
on shadow, initial APICv HW acceleration support, s390 channel IO
based virtio, amongst others"
* tag 'kvm-3.9-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (143 commits)
Revert "KVM: MMU: lazily drop large spte"
x86: pvclock kvm: align allocation size to page size
KVM: nVMX: Remove redundant get_vmcs12 from nested_vmx_exit_handled_msr
x86 emulator: fix parity calculation for AAD instruction
KVM: PPC: BookE: Handle alignment interrupts
booke: Added DBCR4 SPR number
KVM: PPC: booke: Allow multiple exception types
KVM: PPC: booke: use vcpu reference from thread_struct
KVM: Remove user_alloc from struct kvm_memory_slot
KVM: VMX: disable apicv by default
KVM: s390: Fix handling of iscs.
KVM: MMU: cleanup __direct_map
KVM: MMU: remove pt_access in mmu_set_spte
KVM: MMU: cleanup mapping-level
KVM: MMU: lazily drop large spte
KVM: VMX: cleanup vmx_set_cr0().
KVM: VMX: add missing exit names to VMX_EXIT_REASONS array
KVM: VMX: disable SMEP feature when guest is in non-paging mode
KVM: Remove duplicate text in api.txt
Revert "KVM: MMU: split kvm_mmu_free_page"
...
|
|
Many MMC capability flags are platform-dependent and are traditionally set
in platform data. With DT often each such capability requires a special
binding. Add bindings for MMC_CAP_SD_HIGHSPEED, MMC_CAP_MMC_HIGHSPEED,
MMC_CAP_POWER_OFF_CARD and MMC_CAP_SDIO_IRQ capabilities. Also add code to
DT parser to look up "keep-power-in-suspend" and "enable-sdio-wakeup"
bindings and set MMC_PM_KEEP_POWER and MMC_PM_WAKE_SDIO_IRQ respectively,
if found.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Define device-tree bindings for the tmio-mmc driver to be able to specify
parameters, currently provided in platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Clarify ways to specify write-protect and card-detect MMC lines in FDT.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
None of mmc drivers implements bus-width as a required device tree
property. Instead, some drivers like atmel-mci, dw_mmc, sdhci-s3c
implement it as an optional one, and will force bus width to be 1
when the property is absent. Let's change the common binding to
reflect what the drivers are usually doing.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The file Documentation/devicetree/bindings/mmc/mmc.txt is common for all
MMC host drivers. Use a generic MMC host reference instead of an SDHCI
left-over.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The "disable-wp" property is used to specify that a given SD card slot
doesn't have a concept of write protect. This eliminates the need for
special case code for SD slots that should never be write protected
(like a micro SD slot or a dev board).
The dw_mmc driver is special in needing to specify "disable-wp"
because the lack of a "wp-gpios" property means to use the special
purpose write protect line. On some other mmc devices the lack of
"wp-gpios" means that write protect should be disabled.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Thierry writes:
"Remove a duplicate implementation of the CEA VIC lookup and move the CEA
and other mode tables to drm_edid.c to make it more difficult to create
duplicates of the tables.
Add some helpers to pack CEA-861/HDMI AVI, audio and SPD infoframes into
binary buffers that can easily be written into hardware registers. A new
helper function makes it easy construct an AVI infoframe from a DRM
display mode.
Convert the Tegra and Radeon drivers to use the new HDMI helpers."
* 'drm/hdmi-for-3.9' of git://anongit.freedesktop.org/tegra/linux:
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
|
|
Merge second patch-bomb from Andrew Morton:
- A little DM fix
- the MM queue
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (154 commits)
ksm: allocate roots when needed
mm: cleanup "swapcache" in do_swap_page
mm,ksm: swapoff might need to copy
mm,ksm: FOLL_MIGRATION do migration_entry_wait
ksm: shrink 32-bit rmap_item back to 32 bytes
ksm: treat unstable nid like in stable tree
ksm: add some comments
tmpfs: fix mempolicy object leaks
tmpfs: fix use-after-free of mempolicy object
mm/fadvise.c: drain all pagevecs if POSIX_FADV_DONTNEED fails to discard all pages
mm: export mmu notifier invalidates
mm: accelerate mm_populate() treatment of THP pages
mm: use long type for page counts in mm_populate() and get_user_pages()
mm: accurately document nr_free_*_pages functions with code comments
HWPOISON: change order of error_states[]'s elements
HWPOISON: fix misjudgement of page_action() for errors on mlocked pages
memcg: stop warning on memcg_propagate_kmem
net: change type of virtio_chan->p9_max_pages
vmscan: change type of vm_total_pages to unsigned long
fs/nfsd: change type of max_delegations, nfsd_drc_max_mem and nfsd_drc_mem_used
...
|
|
Added slightly more detail to the Documentation of merge_across_nodes, a
few comments in areas indicated by review, and renamed get_ksm_page()'s
argument from "locked" to "lock_it". No functional change.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Izik Eidus <izik.eidus@ravellosystems.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add sysfs documentation for Kernel Samepage Merging (KSM) including new
merge_across_nodes knob.
Signed-off-by: Petr Holasek <pholasek@redhat.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Izik Eidus <izik.eidus@ravellosystems.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Here's a KSM series, based on mmotm 2013-01-23-17-04: starting with
Petr's v7 "KSM: numa awareness sysfs knob"; then fixing the two issues
we had with that, fully enabling KSM page migration on the way.
(A different kind of KSM/NUMA issue which I've certainly not begun to
address here: when KSM pages are unmerged, there's usually no sense in
preferring to allocate the new pages local to the caller's node.)
This patch:
Introduces new sysfs boolean knob /sys/kernel/mm/ksm/merge_across_nodes
which control merging pages across different numa nodes. When it is set
to zero only pages from the same node are merged, otherwise pages from
all nodes can be merged together (default behavior).
Typical use-case could be a lot of KVM guests on NUMA machine and cpus
from more distant nodes would have significant increase of access
latency to the merged ksm page. Sysfs knob was choosen for higher
variability when some users still prefers higher amount of saved
physical memory regardless of access latency.
Every numa node has its own stable & unstable trees because of faster
searching and inserting. Changing of merge_across_nodes value is
possible only when there are not any ksm shared pages in system.
I've tested this patch on numa machines with 2, 4 and 8 nodes and
measured speed of memory access inside of KVM guests with memory pinned
to one of nodes with this benchmark:
http://pholasek.fedorapeople.org/alloc_pg.c
Population standard deviations of access times in percentage of average
were following:
merge_across_nodes=1
2 nodes 1.4%
4 nodes 1.6%
8 nodes 1.7%
merge_across_nodes=0
2 nodes 1%
4 nodes 0.32%
8 nodes 0.018%
RFC: https://lkml.org/lkml/2011/11/30/91
v1: https://lkml.org/lkml/2012/1/23/46
v2: https://lkml.org/lkml/2012/6/29/105
v3: https://lkml.org/lkml/2012/9/14/550
v4: https://lkml.org/lkml/2012/9/23/137
v5: https://lkml.org/lkml/2012/12/10/540
v6: https://lkml.org/lkml/2012/12/23/154
v7: https://lkml.org/lkml/2012/12/27/225
Hugh notes that this patch brings two problems, whose solution needs
further support in mm/ksm.c, which follows in subsequent patches:
1) switching merge_across_nodes after running KSM is liable to oops
on stale nodes still left over from the previous stable tree;
2) memory hotremove may migrate KSM pages, but there is no provision
here for !merge_across_nodes to migrate nodes to the proper tree.
Signed-off-by: Petr Holasek <pholasek@redhat.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Izik Eidus <izik.eidus@ravellosystems.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We now provide an option for users who don't want to specify physical
memory address in kernel commandline.
/*
* For movablemem_map=acpi:
*
* SRAT: |_____| |_____| |_________| |_________| ......
* node id: 0 1 1 2
* hotpluggable: n y y n
* movablemem_map: |_____| |_________|
*
* Using movablemem_map, we can prevent memblock from allocating memory
* on ZONE_MOVABLE at boot time.
*/
So user just specify movablemem_map=acpi, and the kernel will use
hotpluggable info in SRAT to determine which memory ranges should be set
as ZONE_MOVABLE.
If all the memory ranges in SRAT is hotpluggable, then no memory can be
used by kernel. But before parsing SRAT, memblock has already reserve
some memory ranges for other purposes, such as for kernel image, and so
on. We cannot prevent kernel from using these memory. So we need to
exclude these ranges even if these memory is hotpluggable.
Furthermore, there could be several memory ranges in the single node
which the kernel resides in. We may skip one range that have memory
reserved by memblock, but if the rest of memory is too small, then the
kernel will fail to boot. So, make the whole node which the kernel
resides in un-hotpluggable. Then the kernel has enough memory to use.
NOTE: Using this way will cause NUMA performance down because the
whole node will be set as ZONE_MOVABLE, and kernel cannot use memory
on it. If users don't want to lose NUMA performance, just don't use
it.
[akpm@linux-foundation.org: fix warning]
[akpm@linux-foundation.org: use strcmp()]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add functions to parse movablemem_map boot option. Since the option
could be specified more then once, all the maps will be stored in the
global variable movablemem_map.map array.
And also, we keep the array in monotonic increasing order by start_pfn.
And merge all overlapped ranges.
[akpm@linux-foundation.org: improve comment]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: remove unneeded parens]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Tested-by: Lin Feng <linfeng@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
Joachim Eastwood
Fabio Porcedda
Gabor Juhos
Linus Torvalds
Gregory CLEMENT
Andrew Morton
Wouter Verhelst
Corey Minyard
Warren Turkal
Shuah Khan
Daniel Vetter
Jeff Layton
Konrad Rzeszutek Wilk
Michal Marek
Guennadi Liakhovetski
Shawn Guo
Doug Anderson
Dave Airlie
Hugh Dickins
Petr Holasek
Tang Chen