| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The GPIO line name ETHCLK is not aligned with the other signals like
WIFI_CLK. Recently this has been fixed in the vendor tree, so upstream
this change.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The convention to name not connected GPIOs with NC has never been
adapted. Also newer Raspberry Pi boards like RPi 4 never did. So fix
this inconsistency by removing all of the NC names.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
A Wifi/BT chip is quite common for the Raspberry Pi boards. So move those
definitions into a separate dtsi in order to avoid copy & paste. This
change was inspired by a vendor tree patch from Phil Elwell.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-7-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
Fix the node names for the GPIO LEDs to conform to the standard node
name led-..
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622981777-5023-6-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
There might be headless setups of the Compute Module without HDMI,
so better enable HDMI at board level. Btw this allows moving HDMI
base definition into upcoming bcm2835-common.dtsi.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
Now with the varity of several RPi boards, the memory should be defined
at board level. This step gives us the chance to fix the memory size
of the RPi 1 B+, Zero (incl. W) and Compute Module 1.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Eric Anholt <eric@anholt.net>
|
|
The GPIO sysfs is deprecated and disabled in the defconfig files.
So in order to motivate the usage of the new GPIO character device API
add the missing GPIO line names for Raspberry Pi 2 and 3. In the lack
of full schematics i would leave all undocumented pins as unnamed.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
This make the GPIO label for HDMI hotplug more consistent to the other
boards.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
Compiling the bcm283x DTS with W=1 leads to the following warning:
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property,
but no unit name
Fix this by adding the unit address.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
|
|
The commit b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
introduced a wifi power sequence. Unfortunately the polarity of the reset
GPIOs were wrong and broke the wifi support on Raspberry Pi 3 B and
later in 3 B+. This wasn't discovered before since the power sequence
takes only effect in case the relevant MMC driver is compiled as a module.
Fixes: b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
Cc: stable@vger.kernel.org
Reported-by: Matthias Lueschner <lueschem@gmail.com>
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=911443
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
To allow VCHIQ to determine the correct cache line size, use the new
"brcm,bcm2836-vchiq" compatible string on BCM2836 and BCM2837.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
|
|
After commit a98d90e7d588 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO
expander via mailbox service") we are able to control the rest of the
GPIOs of the RPi 3. So add all the missing parts (ACT LED,
Wifi & BT control, HDMI detect) to the DT.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
All RPi 1 and 2 boards used the PWM (audio out) on pin 40 and 45.
So it was easy to define them in bcm2835-rpi.dtsi. Starting with RPi 3
this wont work anymore, because it uses pin 40 and 41. Furthermore the
Zero variants doesn't have audio out.
This patch fixes this pin conflict by moving the PWM node to the board-level.
Change summary:
RPi 3 B: PWM1 45 -> 41
Zero, Zero W: PWM disabled
all other: no functional change
Reported-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Add a description of the RPi3 GPIO expander that the VC4 firmware controls.
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Currently most of the Raspberry Pi DTS have a mixture of magic
numbers and the proper GPIO polarity defines. So use the latter
one consistently.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
This allows to automatically insert the bcm43438 to the bluetooth
subsystem instead of relying on userspace helpers (hciattach).
Overwrite chosen/stdout-path to use 8250 aux uart as console.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Contrary to other RPi devices, RPi3 uses uart0 to communicate with
the BCM43438 bluetooth controller. uart1 is then used for the console.
Today, the console configuration is inherited from the bcm283x dtsi
(bootargs) which is not the correct one for the RPi3. This leads to
routing issue and confuses the Bluetooth controller with unexpected
data.
This patch introduces chosen/stdout path to configure console to uart0
on bcm283x family and overwrite it to uart1 in the RPi3 dts.
Create serial0/1 aliases referring to uart0 and uart1 paths.
Remove unneeded earlyprintk.
Fixes: 4188ea2aeb6d ("ARM: bcm283x: Define UART pinmuxing on board level")
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
Until RPI 3 and Zero W the pl011 (uart0) was always on pin 14/15. So in
order to take care of them and other boards in the future,
we need to define UART pinmuxing on board level.
This work based on Eric Anholt's patch "ARM: bcm2385: Don't force pl011
onto pins 14/15." and Fabian Vogt's patch "ARM64: dts: bcm2837: assign
uart0 to BT and uart1 to pin headers".
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
BCM2837 is somewhat unusual in that we build its DT on both arm32 and
arm64. Most devices are being run in arm32 mode.
Having the body of the DT for 2837 separate from 2835/6 has been a
source of pain, as we often need to make changes that span both
directories simultaneously (for example, the thermal changes for 4.13,
or anything that changes the name of a node referenced by '&' from
board files). Other changes are made more complicated than they need
to be, such as the SDHOST enabling, because we have to split a single
logical change into a 283[56] half and a 2837 half.
To fix this, make the stub board include file live in arm64 instead of
arm32, and keep all of BCM283x's contents in arm32. From here on, our
changes to DT contents can be submitted through a single tree.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Raspbian and Fedora have decided to support the Pi3 in 32-bit mode for
now, so it's useful to be able to test that mode on an upstream
kernel. It's also been useful for me to use the same board for 32-bit
and 64-bit development.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Olof Johansson <olof@lixom.net>
|
Phil Elwell
Stefan Wahren
Stefan Wahren
Linus Torvalds
Phil Elwell
Baruch Siach
Greg Kroah-Hartman
Loic Poulain
Eric Anholt