| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We currently are getting the following warning after a system suspend:
Powerdomain (vpe_pwrdm) didn't enter target state 0
Looks like this is because the STANDBYMODE bit for SMART_IDLE should
not be used. The TRM "Table 12-348. VPE_SYSCONFIG" says that the value
for SMART_IDLE is "0x2: Same behavior as bit-field value of 0x1". But
if the SMART_IDLE value is used, PM_VPE_PWRSTST LASTPOWERSTATEENTERED
bits always show value of 3.
Let's fix the issue by dropping SMART_IDLE for vpe. And let's also add
the missing the powerdomain for vpe.
Fixes: 1a2095160594 ("ARM: dts: dra7: Add ti-sysc node for VPE")
Cc: Benoit Parrot <bparrot@ti.com>
Reported-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The existing fix for errata i940 causes a conflict for IPU2 which is
using timer 3 and 4. From arch/arm/boot/dts/dra7-ipu-dsp-common.dtsi:
&ipu2 {
mboxes = <&mailbox6 &mbox_ipu2_ipc3x>;
ti,timers = <&timer3>;
ti,watchdog-timers = <&timer4>, <&timer9>;
};
The conflict was noticed when booting mainline on the BeagleBoard X15
which has a TI AM5728 SoC:
remoteproc remoteproc1: 55020000.ipu is available
remoteproc remoteproc1: powering up 55020000.ipu
remoteproc remoteproc1: Booting fw image dra7-ipu2-fw.xem4
omap-rproc 55020000.ipu: could not get timer platform device
omap-rproc 55020000.ipu: omap_rproc_enable_timers failed: -19
remoteproc remoteproc1: can't start rproc 55020000.ipu: -19
This change modifies the errata fix to instead use timer 15 and 16 which
resolves the timer conflict.
It does not appear to introduce any latency regression. Results from
cyclictest with original errata fix using dmtimer 3 and 4:
# cyclictest --mlockall --smp --priority=80 --interval=200 --distance=0
policy: fifo: loadavg: 0.02 0.03 0.05
T: 0 ( 1449) P:80 I:200 C: 800368 Min: 0 Act: 32 Avg: 22 Max: 128
T: 1 ( 1450) P:80 I:200 C: 800301 Min: 0 Act: 12 Avg: 23 Max: 70
The results after the change to dmtimer 15 and 16:
# cyclictest --mlockall --smp --priority=80 --interval=200 --distance=0
policy: fifo: loadavg: 0.36 0.19 0.07
T: 0 ( 1711) P:80 I:200 C: 759599 Min: 0 Act: 6 Avg: 22 Max: 108
T: 1 ( 1712) P:80 I:200 C: 759539 Min: 0 Act: 19 Avg: 23 Max: 79
Fixes: 25de4ce5ed02 ("clocksource/drivers/timer-ti-dm: Handle dra7 timer wrap errata i940")
Link: https://lore.kernel.org/linux-omap/YfWsG0p6to3IJuvE@x1/
Suggested-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Link: https://lore.kernel.org/r/20220204053503.1409162-1-dfustini@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Pull ARM devicetree updates from Olof Johansson:
"Like always, the DT branch is sizable. There are numerous additions
and fixes to existing platforms, but also a handful of new ones
introduced. Less than some other releases, but there's been
significant work on cleanups, refactorings and device enabling on
existing platforms.
A non-exhaustive list of new material:
- Refactoring of BCM2711 dtsi structure to add support for the
Raspberry Pi 400
- Rockchip: RK3568 SoC and EVB, video codecs for
rk3036/3066/3188/322x
- Qualcomm: SA8155p Automotive platform (SM8150 derivative),
SM8150/8250 enhancements and support for Sony Xperia 1/1II and
5/5II
- TI K3: PCI/USB3 support on AM64-sk boards, R5 remoteproc
definitions
- TI OMAP: Various cleanups
- Tegra: Audio support for Jetson Xavier NX, SMMU support on Tegra194
- Qualcomm: lots of additions for peripherals across several SoCs,
and new support for Microsoft Surface Duo (SM8150-based), Huawei
Ascend G7.
- i.MX: Numerous additions of features across SoCs and boards.
- Allwinner: More device bindings for V3s, Forlinx OKA40i-C and
NanoPi R1S H5 boards
- MediaTek: More device bindings for mt8167, new Chromebook system
variants for mt8183
- Renesas: RZ/G2L SoC and EVK added
- Amlogic: BananaPi BPI-M5 board added"
* tag 'arm-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (511 commits)
arm64: dts: rockchip: add basic dts for RK3568 EVB
arm64: dts: rockchip: add core dtsi for RK3568 SoC
arm64: dts: rockchip: add generic pinconfig settings used by most Rockchip socs
ARM: dts: rockchip: add vpu and vdec node for RK322x
ARM: dts: rockchip: add vpu nodes for RK3066 and RK3188
ARM: dts: rockchip: add vpu node for RK3036
arm64: dts: ipq8074: Add QUP6 I2C node
arm64: dts: rockchip: Re-add regulator-always-on for vcc_sdio for rk3399-roc-pc
arm64: dts: rockchip: Re-add regulator-boot-on, regulator-always-on for vdd_gpu on rk3399-roc-pc
arm64: dts: rockchip: add ir-receiver for rk3399-roc-pc
arm64: dts: rockchip: Add USB-C port details for rk3399 Firefly
arm64: dts: rockchip: Sort rk3399 firefly pinmux entries
arm64: dts: rockchip: add infrared receiver node to RK3399 Firefly
arm64: dts: rockchip: add SPDIF node for rk3399-firefly
arm64: dts: rockchip: Add Rotation Property for OGA Panel
arm64: dts: qcom: sc7180: bus votes for eMMC and SD card
arm64: dts: qcom: sm8250-edo: Add Samsung touchscreen
arm64: dts: qcom: sm8250-edo: Enable GPI DMA
arm64: dts: qcom: sm8250-edo: Enable ADSP/CDSP/SLPI
arm64: dts: qcom: sm8250-edo: Enable PCIe
...
|
|
dtbs_check produces the following warning for ecap node name:
ecap@100: $nodename:0: 'ecap@100' does not match '^pwm(@.*|-[0-9a-f])*$'
Fix this by replacing ecap with pwm in node name
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With [1] USB4 target-module node got defined in dra74x.dtsi file.
However, the earlier definition in [2] was not removed, and this
duplication of the target module is causing boot failure on dra74
variant boards - dra7-evm, dra76-evm.
USB4 is only present in DRA74x variants, so keeping the entry in
dra74x.dtsi and removing it from the top level interconnect hierarchy
dra7-l4.dtsi file. This change makes the USB4 target module no longer
visible to AM5718, DRA71x and DRA72x so removing references to it in
their respective dts files.
[1]: commit c7b72abca61ec ("ARM: OMAP2+: Drop legacy platform data for
dra7 dwc3")
[2]: commit 549fce068a311 ("ARM: dts: dra7: Add l4 interconnect
hierarchy and ti-sysc data")
Fixes: c7b72abca61ec ("ARM: OMAP2+: Drop legacy platform data for dra7 dwc3")
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ti,omap4-uart was kept around to work with legacy omap-serial driver.
Now that we have completed move to 8250-omap.c drop legacy compatible.
This will simplify writing YAML schema.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM SoC updates from Arnd Bergmann:
"Almost all SoC code changes this time are for the TI OMAP platform,
which continues its decade-long quest to move from describing a
complex SoC in code to device tree.
Aside from this, the Uniphier platform has a new maintainer and some
platforms have minor bugfixes and cleanups that were not urgent enough
for v5.12"
* tag 'arm-soc-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
MAINTAINERS: Update ARM/UniPhier SoCs maintainers and status
mailmap: Update email address for Nicolas Saenz
MAINTAINERS: Update BCM2711/BCM2335 maintainer's mail
ARM: exynos: correct kernel doc in platsmp
ARM: hisi: use the correct HiSilicon copyright
ARM: ux500: make ux500_cpu_die static
ARM: s3c: Use pwm_get() in favour of pwm_request() in RX1950
ARM: OMAP1: fix incorrect kernel-doc comment syntax in file
ARM: OMAP2+: fix incorrect kernel-doc comment syntax in file
ARM: OMAP2+: Use DEFINE_SPINLOCK() for spinlock
ARM: at91: pm: Move prototypes to mutually included header
ARM: OMAP2+: use true and false for bool variable
ARM: OMAP2+: add missing call to of_node_put()
ARM: OMAP2+: Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
ARM: imx: Kconfig: Fix typo in help
ARM: mach-imx: Fix a spelling in the file pm-imx5.c
bus: ti-sysc: Warn about old dtb for dra7 and omap4/5
ARM: OMAP2+: Stop building legacy code for dra7 and omap4/5
ARM: OMAP2+: Drop legacy platform data for omap5 hwmod
ARM: OMAP2+: Drop legacy platform data for omap5 l3
...
|
|
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm percpu timers instead.
Let's configure dmtimer3 and 4 as percpu timers by default, and warn about
the issue if the dtb is not configured properly.
Let's do this as a single patch so it can be backported to v5.8 and later
kernels easily. Note that this patch depends on earlier timer-ti-dm
systimer posted mode fixes, and a preparatory clockevent patch
"clocksource/drivers/timer-ti-dm: Prepare to handle dra7 timer wrap issue".
For more information, please see the errata for "AM572x Sitara Processors
Silicon Revisions 1.1, 2.0":
https://www.ti.com/lit/er/sprz429m/sprz429m.pdf
The concept is based on earlier reference patches done by Tero Kristo and
Keerthy.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210323074326.28302-3-tony@atomide.com
|
|
We can now probe devices with ti-sysc interconnect driver and dts data.
Let's drop the related platform data and custom ti,hwmods dts property.
As we're just dropping data, and the early platform data init is based on
the custom ti,hwmods property, we want to drop both the platform data and
ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe interconnects with device tree only configuration using
simple-pm-bus and genpd.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe interconnects with device tree only configuration using
simple-pm-bus and genpd.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe interconnects with device tree only configuration using
simple-pm-bus and genpd.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe interconnects with device tree only configuration using
simple-pm-bus and genpd.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe interconnects with device tree only configuration using
simple-pm-bus and genpd.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Note that the old sysc register offset is wrong, the real offset is at
0x1100 as listed in TRM for SATA_SYSCONFIG register. Looks like we've been
happily using sata on the bootloader configured sysconfig register and
nobody noticed. Also the old register range for SATAMAC_wrapper registers
is wrong at 7 while it should be 8. But that too seems harmless.
There is also an L3 parent interconnect range that we don't seem to be
using. That can be added as needed later on.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM Devicetree updates from Olof Johansson:
"As usual, most of the changes are to devicetrees.
Besides smaller fixes, some refactorings and cleanups, some of the new
platforms and chips (or significant features) supported are below:
Broadcom boards:
- Cisco Meraki MR32 (BCM53016-based)
- BCM2711 (RPi4) display pipeline support
Actions Semi boards:
- Caninos Loucos Labrador SBC (S500-based)
- RoseapplePi SBC (S500-based)
Allwinner SoCs/boards:
- A100 SoC with Perf1 board
- Mali, DMA, Cetrus and IR support for R40 SoC
Amlogic boards:
- Libretch S905x CC V2 board
- Hardkernel ODROID-N2+ board
Aspeed boards/platforms:
- Wistron Mowgli (AST2500-based, Power9 OpenPower server)
- Facebook Wedge400 (AST2500-based, ToR switch)
Hisilicon SoC:
- SD5203 SoC
Nvidia boards:
- Tegra234 VDK, for pre-silicon Orin SoC
NXP i.MX boards:
- Librem 5 phone
- i.MX8MM DDR4 EVK
- Variscite VAR-SOM-MX8MN SoM
- Symphony board
- Tolino Shine 2 HD
- TQMa6 SoM
- Y Soft IOTA Orion
Rockchip boards:
- NanoPi R2S board
- A95X-Z2 board
- more Rock-Pi4 variants
STM32 boards:
- Odyssey SOM board (STM32MP157CAC-based)
- DH DRC02 board
Toshiba SoCs/boards:
- Visconti SoC and TPMV7708 board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (638 commits)
ARM: dts: nspire: Fix SP804 users
arm64: dts: lg: Fix SP804 users
arm64: dts: lg: Fix SP805 clocks
ARM: mstar: Fix up the fallout from moving the dts/dtsi files
ARM: mstar: Add mstar prefix to all of the dtsi/dts files
ARM: mstar: Add interrupt to pm_uart
ARM: mstar: Add interrupt controller to base dtsi
ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
arm64: dts: ti: k3-j7200-common-proc-board: Add USB support
arm64: dts: ti: k3-j7200-common-proc-board: Configure the SERDES lane function
arm64: dts: ti: k3-j7200-main: Add USB controller
arm64: dts: ti: k3-j7200-main.dtsi: Add USB to SERDES lane MUX
arm64: dts: ti: k3-j7200-main: Add SERDES lane control mux
dt-bindings: ti-serdes-mux: Add defines for J7200 SoC
ARM: dts: hisilicon: add SD5203 dts
ARM: dts: hisilicon: fix the system controller compatible nodes
arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
arm64: dts: zynqmp: Remove undocumented u-boot properties
arm64: dts: zynqmp: Remove additional compatible string for i2c IPs
arm64: dts: zynqmp: Rename buses to be align with simple-bus yaml
...
|
|
All dra7/am57 boards converted to use new driver, so drop legacy
cpsw dt node.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and
following the already supported Cortex-A1`5 and Cortex-A57 based
Alpine chips. This one is added together with the official
Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile
phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total
of five end-user products are added based on these, all Android
phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals. It is added along with the HopeRun HiHope
RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based
on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels and
become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board for
the Tegra194, their latest 64-bit chip based on Carmel CPU cores
and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added: The
MYiR MYS-6ULX single-board computer, and four different models of
industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia
Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards. Beacon EmbeddedWorks adds another
SoM+Carrier development board for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is
based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)"
* tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits)
arm64: dts: meson: odroid-n2: add jack audio output support
arm64: dts: meson: odroid-n2: enable audio loopback
ARM: dts: berlin: Align L2 cache-controller nodename with dtschema
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
...
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes for omaps for v5.8
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
* tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
Link: https://lore.kernel.org/r/pull-1591889257-410830@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The commit 5390130f3b28 ("ARM: dts: dra7: add timer_sys_ck entries
for IPU/DSP timers") was added to allow the OMAP clocksource timer
driver to use the clock aliases when reconfiguring the parent clock
source for the timer functional clocks after the timer_sys_ck clock
aliases got cleaned up in commit a8202cd5174d ("clk: ti: dra7: drop
unnecessary clock aliases").
The above patch however has missed adding the entries for couple of
timers (14, 15 and 16), and also added erroneously in the parent
ti-sysc nodes for couple of clocks (timers 4, 5 and 6). Fix these
properly, so that any of these timers can be used with OMAP remoteproc
IPU and DSP devices. The always-on timers 1 and 12 are not expected
to use this clock source, so they are not modified.
Fixes: 5390130f3b28 ("ARM: dts: dra7: add timer_sys_ck entries for IPU/DSP timers")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"This is the set of device tree changes, mostly covering new hardware
support, with 577 patches touching a little over 500 files.
There are five new Arm SoCs supported in this release, all of them for
existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in both NAS
devices and Android Set-top-box designs, along with the
"Horseradish", "Lion Skin" and "Mjolnir" reference platforms; the
Mele X1000 and Xnano X5 set-top-boxes and the Banana Pi BPi-M4
single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC and
the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the Odroid-GO
Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2" and YADRO
OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform" reference
board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board computer
and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in
existing SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone"
* tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (564 commits)
ARM: dts: keystone: Rename "msmram" node to "sram"
arm: dts: mt2712: add uart APDMA to device tree
arm64: dts: mt8183: add mmc node
arm64: dts: mt2712: add ethernet device node
arm64: tegra: Make the RTC a wakeup source on Jetson Nano and TX1
ARM: dts: mmp3: Add the fifth SD HCI
ARM: dts: berlin*: Fix up the SDHCI node names
ARM: dts: mmp3: Fix USB & USB PHY node names
ARM: dts: mmp3: Fix L2 cache controller node name
ARM: dts: mmp*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa910: Fix the gpio interrupt cell number
ARM: dts: pxa3xx: Fix up encoding of the /gpio interrupts property
ARM: dts: pxa168: Fix the gpio interrupt cell number
ARM: dts: pxa168: Add missing address/size cells to i2c nodes
ARM: dts: dove: Fix interrupt controller node name
ARM: dts: kirkwood: Fix interrupt controller node name
arm64: dts: Add SC9863A emmc and sd card nodes
arm64: dts: Add SC9863A clock nodes
arm64: dts: mt6358: add PMIC MT6358 related nodes
...
|
|
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Note that similar to omap_init_time_of(), we now need to call
omap_clk_init() also from omap5_realtime_timer_init().
Cc: devicetree@vger.kernel.org
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With this, the clocksource driver can setup the timers properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
DMTimers 13 - 16 are PWM capable and also can be used for CPTS input
signals generation. Hence, mark them as "ti,timer-pwm".
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Late omap dts changes for v5.6 merge window
This series of changes mostly configures the cameras for dra7 and
am437x that have been pending for few months now because of waiting
for clock dependencies to clear. So these changes are based on earlier
dts changes with with Tero Kristo's for-5.6-ti-clk branch merged in.
Then there's a series of changes to configure powervr sgx target module
for am335x, am437x and dra7 that have been waiting to have the rstctrl
reset driver dependencies to clear.
Also included are few minor patches to configure 1-wire and coulomb
counter calibration interrupt for droid4.
* tag 'omap-for-v5.6/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: dts: Add omap3-echo
ARM: dts: Add dtsi files for AM3703, AM3715 and DM3725
ARM: dts: am335x-icev2: Add support for OSD9616P0899-10 at i2c0
...
Link: https://lore.kernel.org/r/pull-1579896427-50330@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add VPE node as a child of l4 interconnect in order for it to probe
using ti-sysc.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add CAM nodes as a child of l4 interconnect in order for it to probe
using ti-sysc.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Vinod Koul <vkoul@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Franklin S Cooper Jr <fcooper@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Suman Anna <s-anna@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Franklin S Cooper Jr <fcooper@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We need this to pass auxdata to all the sdma instances.
Cc: devicetree@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Vinod Koul <vkoul@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Device tree fixes for omap variants for for v5.5 merge window
This series of changes contains fixes for few SoC and board specific
issues that would be good to have merged for v5.5-rc1:
- Fix incorrect MMC card detection polarity for omap3-tao3530
- Fix wrong am57xx-beagle-x15 pinmux named states for eMMC
- Fix dra7 cpsw mdio clock that causes wrong speed
- Fix vcsi for droid4 so it won't get turned off after init
- Fix rev and sysconfig register offsets for omap4 sgx so it can idle
Then there are also two minor late changes to logicpd-torpedo-baseboard
to configure 1-wire HDQ for battery stats, and remove out of date
workaround comments no longer needed.
* tag 'omap-for-v5.5/dt-fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix sgx sysconfig register for omap4
ARM: dts: Fix vcsi regulator to be always-on for droid4 to prevent hangs
ARM: dts: dra7: fix cpsw mdio fck clock
ARM: dts: am57xx-beagle-x15: Update pinmux name to ddr_3_3v
ARM: dts: omap3-tao3530: Fix incorrect MMC card detection GPIO polarity
ARM: dts: logicpd-torpedo: Remove unnecessary notes/comments
ARM: dts: logicpd-torpedo-baseboard: Enable HDQ
Link: https://lore.kernel.org/r/pull-1574870758-237468@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull ARM Device-tree updates from Olof Johansson:
"As always, the bulk of updates. Some of the news this cycle:
New SoC descriptions:
- Broadcom BCM2711
- Amlogic Meson A1 and G12
- Freescale S32V234
- Marvell Armada AP807/AP807-quad and CP115
- Realtek RTD1293 and RTD1296
- Rockchip RK3308
New boards and platforms:
- Allwinner: NanoPi Duo2
- Amlogic: Ugoos am6
- Atmel at91: Overkiz Kizbox2/4
- Broadcom: RPi4, Luxul XWC-2000
- Marvell: New Espressobin flavor
- NXP: i.MX8MN LPDDR4 EVK, i.MX8QXP Colibri, S32V234 EVB, Netronix
E60K02 and Kobo Clara HD, Kontron N6311 and N6411, OPOS6UL and
OPOS6ULDev
- Renesas: Salvator-XS
- Rockchip: Beelink A1 (rk3308), rk3308 eval boards, rk3399-roc-pc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (653 commits)
ARM: dts: logicpd-torpedo: Disable USB Host
arm: dts: mt6323: add keys, power-controller, rtc and codec
arm64: dts: mt8183: add systimer0 device node
dt-bindings: mediatek: update bindings for MT8183 systimer
arm64: dts: rockchip: fix sdmmc detection on boot on rk3328-roc-cc
arm64: dts: rockchip: Split rk3399-roc-pc for with and without mezzanine board.
arm64: dts: rockchip: Add Beelink A1
dt-bindings: ARM: rockchip: Add Beelink A1
arm64: dts: rockchip: Add RK3328 audio pipelines
arm64: dts: ti: k3-j721e-common-proc-board: Add USB ports
arm64: dts: ti: k3-j721e-main: add USB controller nodes
ARM: dts: aspeed-g6: Add timer description
ARM: dts: aspeed: ast2600evb: Enable i2c buses
ARM: dts: at91: add a dts and dtsi file for kizbox2 based boards
dt-bindings: arm: at91: Document Kizbox2-2 board binding
arm64: dts: meson-gx: fix i2c compatible
arm64: dts: meson-gx: cec node should be disabled by default
arm64: dts: meson-g12b-odroid-n2: add missing amlogic, s922x compatible
arm64: dts: meson-gxm: fix gpu irq order
arm64: dts: meson-g12a: fix gpu irq order
...
|
|
Add DT nodes for new cpsw switch dev driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DRA7 CPSW MDIO functional clock (gmac_clkctrl DRA7_GMAC_GMAC_CLKCTRL 0)
is specified incorrectly, which is caused incorrect MDIO bus clock
configuration MDCLK. The correct CPSW MDIO functional clock is
gmac_main_clk (125MHz), which is the same as CPSW fck. Hence fix it.
Fixes: 1faa415c9c6e ("ARM: dts: Add fck for cpsw mdio for omap variants")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Drop legacy platform data for omaps for v5.5
This series of changes continues dropping legacy platform data for
omaps. With the proper device tree configuration in place in the dts
files for ti-sysc interconnect target module driver, we can drop the
related platform data and legacy ti,hwmods custom property.
Most of the patches in this series drop platform data and custom dts
property one device class and one SoC at time. This way we can easily
revert one patch at a time in case of unexpected issues if the fix is
not trivial.
For am335x musb, we need to first update the device tree to probe with
ti-sysc interconnect target module driver. And then the following
patches drop the legacy platform data.
Note that this series depends on earlier ti-sysc related driver changes
* tag 'omap-for-v5.5/ti-sysc-drop-pdata-v2-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (40 commits)
ARM: OMAP2+: Drop legacy platform data for am335x musb
ARM: dts: Drop pointless status changing for am3 musb
ARM: dts: Probe am335x musb with ti-sysc
ARM: OMAP2+: Drop legacy platform data for musb on omap4
ARM: OMAP2+: Drop legacy platform data for omap4 mcasp
ARM: OMAP2+: Drop legacy platform data for am3 and am4 mcasp
ARM: OMAP2+: Drop legacy platform data for dra7 rng
ARM: OMAP2+: Drop legacy platform data for am3 and am4 rng
ARM: OMAP2+: Drop legacy platform data for omap4 hdq1w
ARM: OMAP2+: Drop legacy platform data for dra7 hdq1w
ARM: OMAP2+: Drop legacy platform data for am4 hdq1w
ARM: OMAP2+: Drop legacy platform data for omap5 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap4 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap5 wdt
ARM: OMAP2+: Drop legacy platform data for dra7 wdt
ARM: OMAP2+: Drop legacy platform data for am3 and am4 wdt
ARM: dts: Drop custom hwmod property for omap5 mmc
ARM: dts: Drop custom hwmod property for am4 mmc
ARM: dts: Drop custom hwmod property for am3 mmc
ARM: dts: Drop custom hwmod property for omap5 i2c
...
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
Tony Lindgren
Drew Fustini
Linus Torvalds
Lokesh Vutla
Gowtham Tammana
Vignesh Raghavendra
Grygorii Strashko
Arnd Bergmann
Suman Anna
Tero Kristo
Olof Johansson
Benoit Parrot