| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The GW52xx has a transceiver with a STBY pin connected to an IMX6 GPIO.
Configure this as a regulator to drive it low when CAN is in use.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add USB OTG over-current pinmux to the GW51xx/GW52xx/GW54xx/GW553x
boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the unnecessary #address-cells/#size-cells to avoid warnings
from W=1 build like this:
arch/arm/boot/dts/imx6qdl-gw52xx.dtsi:33.12-78.4: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[fabio: Make the warning messages more succint]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
2 regulator descriptions carry identical naming.
This leads to following boot warning:
[ 0.173138] debugfs: Directory 'vdd1p8' with parent 'regulator' already present!
Fix this by renaming the one used for audio.
Fixes: 5051bff33102 ("ARM: dts: imx: ventana: add LTC3676 PMIC support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: stable@vger.kernel.org # v4.11
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee28 ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add Gateworks System Controller support to Gateworks Ventana boards:
- add dt bindings for GSC mfd driver and hwmon driver for ADC's and
fan controllers.
- add dt bindings for gpio-keys driver for push-button and interrupt events
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The imx-pwm driver supports 3 cells and this is the more flexible setting.
So use it by default and overwrite it back to two for the files that
reference the PWMs with just 2 cells to minimize changes.
This allows to drop explicit setting to 3 cells for the boards that already
depend on this. The boards that are now using 2 cells explicitly can be
converted to 3 individually.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add fxos8700 iio imu entries for Gateworks ventana SBCs.
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Boards based on imx6qdl have duplicate memory nodes:
- One coming from the board device tree file: memory@
- One coming from the imx6qdl.dtsi file.
Fix the duplication by removing the memory node from
the imx6qdl.dtsi file and by adding 'device_type = "memory";'
in the board Device Tree.
Converted using the following command:
perl -p0777i -e 's/memory\@10000000 \{\n/memory\@10000000 \{\n\t\tdevice_type = \"memory\";\n/m' `find ./arch/arm/boot/dts -name "imx6*"``
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull "i.MX device tree updates for 4.15" from Shawn Guo:
- New board support: i.MX51 ZII RDU1, i.MX53 GE Healthcare PPD, i.MX6
TX modules for MB7 from Ka-Ro Electronics, i.MX6 Wandboard revd1
variants, i.MX6 LWN DISPLAY5 board, Pistachio i.MX6Q board, i.MX6SX
Vining-2000 board.
- Use the 'vpcie-supply' property for PCIe device for boards
imx6qdl-sabresd, imx6q-novena and imx6q-cm-fx6.
- A series from Jagan Teki to update imx6qdl-icore board with audio,
touch and CAN support.
- Switch to nvmem for accessing OCOTP from tempmon for i.MX6SX and add
tempmon support for i.MX6UL.
- A bunch of patches from Lothar Waßmann updating Ka-Ro i.MX28, i.MX53
and i.MX6 TX modules.
- Fix DTC warnings in i.MX device trees, dropping leading zeros from
unit address, correcting display nodes notation and display port
names, fixing nodes with unit name and no reg property.
- Other random device updates for various board support.
* tag 'imx-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (63 commits)
ARM: dts: imx53-tx53: fix interrupt flags
ARM: dts: imx28-tx28: fix interrupt flags
ARM: dts: display5: Device tree description of LWN's DISPLAY5 board
ARM: dts: imx53-qsb-common: Fix 'led_gpio7_7@0' node with unit name and no reg property
ARM: dts: imx53-m53evk: Fix 'led_gpio@0' node with unit name and no reg property
ARM: dts: imx53: Fix 'usbphy@x' node with unit name and no reg property
ARM: dts: imx51-ts4800: Fix 'port@0' node with unit name and no reg property
ARM: dts: imx51-apf51dev: Fix 'backlight@bl1' node with unit name and no reg property
ARM: dts: imx: add ZII RDU1 board
ARM: dts: imx: add support for TX6 modules on MB7 baseboard
ARM: dts: imx: add support for TX6QP
ARM: dts: imx6-tx6: add a .dtsi file for the MB7 baseboard
ARM: dts: imx6-tx6: move display configuration to .dtsi file
ARM: dts: imx6-tx6: add support for I2C bus recovery
ARM: dts: imx6-tx6: convert to using simple-audio-card
ARM: dts: imx6-tx6: specify ethernet phy reset post-delay
ARM: dts: imx6-tx6: improve ethernet related pinctrl setup
ARM: dts: imx6-tx6: add trickle-charge config for DS1339
ARM: dts: imx6-tx6: remove obsolete ipu1 alias
ARM: dts: imx6-tx6: remove obsolete eeti,egalax_ts
...
[arnd: made sure we have no new leading zeroes in unit address during merge]
|
|
The container node in the iomuxc node is no longer necessary and causes
pinctl errors on the Ventana boards with analog video capture
since aa12693e4156adafdef80a8bd134123a6419621b:
pinctrl core: initialized pinctrl subsystem
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/adv7180grp
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/ipu2_csi1grp
imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
imx6q-pinctrl 20e0000.iomuxc: function 'iomuxc' not supported
imx6q-pinctrl 20e0000.iomuxc: invalid function iomuxc in map table
imx6q-pinctrl 20e0000.iomuxc: function 'iomuxc' not supported
imx6q-pinctrl 20e0000.iomuxc: invalid function iomuxc in map table
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The 'uart-has-rtscts' property should be used when the board exposes the
native RTS and CTS UART pins.
On the imx6qdl-gw5xxx boards such pins are not used, so remove the
'uart-has-rtscts' property to make the hardware description correct.
Documentation/devicetree/bindings/serial/serial.txt states that
'uart-has-rtscts' and 'rts-gpios' properties are mutually exclusive.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fixed code indent tabs in respective imx6qdl dtsi files and
also add space on imx6qdl-icore-rqs.dtsi on usdhc bus-width nodes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit b36581df7e78 ("spi: imx: Using existing properties for
chipselects") the device tree property 'fsl,spi-num-chipselects' is
unused and it is already marked as obsolete in device tree binding
documentation. Remove the property from the existing DTS files to
avoid its reoccurence on copying.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
All of the Gateworks Ventana boards based on the IMX6 SoC except for the
GW54xx use the LTC3676 PMIC. Add a device-tree node with interrupt support
for this PMIC. Additionally remove the simple-bus notation in the regulator
nodes and any fixed regulators that are provided by the PMIC.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fixed code indent tabs in respetcive imx6qdl dtsi files.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Several dts files set a bit in the SPEED field for pads
RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there
doesn't have an effect and the bit reads as zero.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
bc677ff42e81bbf78308a7b66cf7b63b0f5c26b0 adds a device-tree property
to specify that an external watchdog reset is used to reset other
portions of the board and not just the IMX6 SoC.
This adds the property to the proper watchdog as well as the pinmux for
the Gateworks Ventana boards that use this external watchdog reset to
reset the PMIC which will reset all the PMIC power rails and not just
a chip-level IMX6 reset. This helps to work around various system issues
that can cause a hang when coming out of reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Using "IMX6QDL_CLK_CKO" for the clock is easier to read instead of
the hardcoded clock number.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix some invalid pwm pinmux configurations.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This addes support for SPI available on an off-board connector available on
some models of the GW52xx.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Ventana boards have an off-board connector with signals that can be pinmuxed
as either GPIO or PWM. This patch adds pwm device-tree nodes in the disabled
state which the bootloader can decide to enable based on bootloader config.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently it is not possible to have HDMI and LVDS working simultaneously,
because both ports try to use PLL5.
Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
driven from independent sources.
With this change the LDB pixel clock goes to 68.57 MHz, which is still
within the valid range for the displays supported by the Ventana boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Gateworks Ventana boards seem to need "RGMII-ID" (internal delay)
PHY mode, instead of simple "RGMII", for their Marvell 88E1510
transceiver. Otherwise, the Ethernet MAC doesn't work with Marvell PHY
driver (TX doesn't seem to work correctly).
Tested on GW5400 rev. C.
This bug affects ARM Fedora 23.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
|
|
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
UHS-I support is available on Ventana boards with micro-SD sockets depending
on the board revision. To support this pinctl states for 100Mhz and 200MHz
must be added as well as pinmux of the VSELECT signal. In order to support
UHS-I the I/O rail of the 4-bit data bus must be switchable between 1.8V
and 3.3V.
By adding the no-1-8-v property, which disables UHS-I support, we allow the
bootloader to be in charge of selecting which boards have this capability
by removing that property if the board model/revision implement the support.
Additionally we will remove NANDF_CS1 here from the nand pinmux group as the
second chip-select is not used on any ventana boards and this is the pad
that is used for SD3_VELECT.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
imx6qdl-gw5x boards use sgtl5000 codec and the machine file (imx-sgtl5000)
already sets SSI in slave mode and codec in master mode, so there is no need
for having this property.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The GW52xx baseboard supports CANbus so we enable it, configure its pinmux
and CAN_STBY gpio.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Follow the conventions for pinctrl:
- grouping pinctrl in logical alphabatized groups
- remove any pinctrl not being used by a driver or needed by user
- move iomuxc to bottom of file for readability
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Follow the convention of configuring padconf for all pins and not leaving
any 0x80000000 to leave them un-configured.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Use the gpio contants defined in bindings for active high/low
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Remove aliases that are either not used by bootloader or are provided via
included dtsi files.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The general device-tree rule is to not include nodes that do not have a driver
or bindings in a dts/dtsi. Remove the place-holder nodes from the Gateworks
Ventana boards until a time that a driver with proper bindings exists.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The DAI mode is and should be configured by the sound card driver as
codec and ssi have to be in the right modes to communicate with each
other. It is possible to operate the ssi unit or the codec in master mode,
sometimes even on the same board in different configurations.
With the latest changes in the fsl-ssi driver, the 'fsl,mode' property
is only handled as a fallback property. If the sound card sets the DAI
mode correctly, this fallback configuration is dropped.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The 'model' property in the imx-audio-sgtl5000 binding specifies the
user-visible name of the audio device. This should be something common and
not baseboard specific.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Correct the invalid clock for the sgtl5000 audio codec on the GW52xx Ventana
baseboard.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The vendor prefix for Linear Technology should be lltc,
same as the NASDAQ symbol.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The GW52xx supports LVDS on channel 0. Remove the obsolete crtcs node and
add display timings for the HanStar HSD100PXN1 display.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
The GW54xx/GW53xx/GW52xx all support LVDS with a PWM controlled backlight.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Configure ddc and enable HDMI
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Since commit (655b43c staging: imx-drm-core: Use OF graph to find
components and connections between encoder and crtcs), 'crtcs' becomes a
dead property. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
|
|
The Gateworks Ventana product family consists of several baseboard designs
based on the Freescale i.MX6 family of processors. Each baseboard has a
different set of possible features.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
Tim Harvey
Koen Vandeputte
Krzysztof Kozlowski
Fabio Estevam
Uwe Kleine-König
Robert Jones
Thomas Gleixner
Marco Franchi
Marco Franchi
Arnd Bergmann
Rob Herring
Fabio Estevam
Jagan Teki
Vladimir Zapolskiy
Jagan Teki
Uwe Kleine-König
Krzysztof Hałasa
Linus Torvalds
Dong Aisheng
Fabio Estevam
Markus Pargmann
Philipp Zabel
Shawn Guo