| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since SoM revision 1.9 the PHY has been replaced with an ADIN1300,
add an entry for it next to the original.
As Russell King pointed out, additional phy nodes cause warnings like:
mdio_bus 2188000.ethernet-1: MDIO device at address 1 is missing
To avoid this the new node has its status set to disabled. U-Boot will
be modified to enable the appropriate phy node after probing.
The existing ar8035 nodes have to stay enabled by default to avoid
breaking existing systems when they update Linux only.
Co-developed-by: Alvaro Karsz <alvaro.karsz@solid-run.com>
Signed-off-by: Alvaro Karsz <alvaro.karsz@solid-run.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The AR803x PHY used on this modules seems to require the reset line to
be asserted for around 10ms in order to avoid rare cases where the PHY
gets stuck in an incoherent state that prevents it to function
correctly.
The previous value of 2ms was found to be problematic on some setups,
causing intermittent issues where the PHY would be unresponsive
every once in a while on some sytems, with a low occurrence (it typically
took around 30 consecutive reboots to encounter the issue).
Bumping the delay to the 10ms makes the issue dissapear, with more than
2500 consecutive reboots performed without the issue showing-up.
Fixes: 208d7baf8085 ("ARM: imx: initial SolidRun HummingBoard support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Hervé Codina <herve.codina@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Increase the SmartEEE Tw parameter for Atheros PHYs to stop gigabit
links from sporadically dropping. Jon Nettleton found that a value
of 23 was the minimum to give a stable link, but testing with the
Com Express 7 module shows 24 is the minimum - so 23 may still be on
the margins. Use 24 instead for consistency across SolidRun platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PHY address bit 2 is configured by the LED pin. Attaching a LED
to this pin is not sufficient to guarantee this configuration pin is
correctly read. This leads to some platforms having their PHY at
address 0 and others at address 4.
If there is no phy-handle specified, the FEC driver will scan the PHY
bus for a PHY and use that. Consequently, adding the DT configuration
of the PHY and the phy properties to the FEC driver broke some boards.
Fix this by removing the phy-handle property, and listing two PHY
entries for both possible PHY addresses, so that the DT configuration
for the PHY can be found by the PHY driver.
Fixes: 86b08bd5b994 ("ARM: dts: imx6-sr-som: add ethernet PHY configuration")
Reported-by: Christoph Mattheis <christoph.mattheis@arcor.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add ethernet PHY configuration ahead of removing the quirk that
configures the clocking mode for the PHY. The RGMII delay is
already set correctly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit 6d4cd041f0af ("net: phy: at803x: disable delay only for RGMII mode")
exposed an issue on imx DTS files using AR8031/AR8035 PHYs.
The end result is that the boards can no longer obtain an IP address
via UDHCP, for example.
Quoting Andrew Lunn:
"The problem here is, all the DTs were broken since day 0. However,
because the PHY driver was also broken, nobody noticed and it
worked. Now that the PHY driver has been fixed, all the bugs in the
DTs now become an issue"
To fix this problem, the phy-mode property needs to be "rgmii-id", which
has the following meaning as per
Documentation/devicetree/bindings/net/ethernet.txt:
"RGMII with internal RX and TX delays provided by the PHY, the MAC should
not add the RX or TX delays in this case)"
Tested on imx6-sabresd, imx6sx-sdb and imx7d-pico boards with
successfully restored networking.
Based on the initial submission from Steve Twiss for the
imx6qdl-sabresd.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Soeren Moch <smoch@web.de>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a 3.3V regulator for devices connected to the vcc_3v3 supply
signal on the microsom.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are two variants of the imx6qdl som: one with Broadcom Wi-Fi and
another with Texas Instruments Wi-Fi. The two Wi-Fi devices require
different DT bindings, so it's necessary to split out the Broadcom
specifics.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use real iomuxc values rather than preserving the boot loader value for
the SOMs ethernet.
Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Jon and myself feel that "imx6qdl-microsom" is too generic a name for
SolidRun's microsom - some other manufacturer could have their own
microsom. Change the name to the shorter "imx6qdl-sr-som".
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
Josua Mayer
Maxime Chevallier
Russell King
Fabio Estevam