| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Armv8 Juno fix for v6.1
Just a single fix to add the missing critical points in the thermal
zones that has been mandatory in the binding but was enforced in the
code recently.
* tag 'juno-fix-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Add thermal critical trip points
Link: https://lore.kernel.org/r/20221102140156.2758137-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When thermnal zones are defined, trip points definitions are mandatory.
Define a couple of critical trip points for monitoring of existing
PMIC and SOC thermal zones.
This was lost between txt to yaml conversion and was re-enforced recently
via the commit 8c596324232d ("dt-bindings: thermal: Fix missing required property")
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Fixes: f7b636a8d83c ("arm64: dts: juno: add thermal zones for scpi sensors")
Link: https://lore.kernel.org/r/20221028140833.280091-8-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: 0420dde30a90 ("arm64: dts: ls208xa: add the external MDIO nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: bbe75af7b092 ("arm64: dts: ls1088a: add external MDIO device nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: 6e1b8fae892d ("arm64: dts: lx2160a: add emdio1 node")
Fixes: 5705b9dcda57 ("arm64: dts: lx2160a: add emdio2 node")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per imx93-pinfunc.h and pinctrl-imx93.c, correct gpio-ranges.
Fixes: ec8b5b5058ea ("arm64: dts: freescale: Add i.MX93 dtsi support")
Reported-by: David Wolfe <david.wolfe@nxp.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per binding doc, interrupt names should be tx and rx.
Fixes: 0dfb380d2492 ("arm64: dts: imx93: add s4 mu node")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per bindings/mmc/fsl-imx-esdhc.yaml, the clock order is ipg, ahb, per,
otherwise warning: "
mmc@5b020000: clock-names:1: 'ahb' was expected
mmc@5b020000: clock-names:2: 'per' was expected "
Fixes: 16c4ea7501b1 ("arm64: dts: imx8: switch to new lpcg clock binding")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
pgc_otg1 is actual the power domain of usb PHY, usb controller
is in hsio power domain, and pgc_otg1 is required to be powered
up to detect usb remote wakeup, so move the pgc_otg1 power domain
to the usb phy node.
Fixes: ea2b5af58ab2 ("arm64: dts: imx8mn: put USB controller into power-domains")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
pgc_otg1 is an independent power domain of hsio, it's for usb phy,
so remove hsio power domain from its node.
Fixes: 8b8ebec67360 ("arm64: dts: imx8mn: add GPC node")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
pgc_otg1/2 is actual the power domain of usb PHY, usb controller
is in hsio power domain, and pgc_otg1/2 is required to be powered
up to detect usb remote wakeup, so move the pgc_otg1/2 power domain
to the usb phy node.
Fixes: 01df28d80859 ("arm64: dts: imx8mm: put USB controllers into power-domains")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
pgc_otg1/2 are independent power domain of hsio, they for usb phy,
so remove hsio power domain dependency from its node.
Fixes: d39d4bb15310 ("arm64: dts: imx8mm: add GPC node")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GPIO signaling ctrl_sleep_moci is currently handled as a gpio hog.
But the gpio-hog node is made a child of the wrong gpio controller.
Move it to the node representing gpio4 so that it actually works.
Without this carrier board components jumpered to use the signal are
unconditionally switched off.
Fixes: a39ed23bdf6e ("arm64: dts: freescale: add initial support for verdin imx8m plus")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable CPLD_Dn pull down resistor instead of pull up to avoid
intefering with CPLD power off functionality.
Fixes: 510c527b4ff57 ("arm64: dts: imx8mm: Add i.MX8M Mini Toradex Verdin based Menlo board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull clk updates from Stephen Boyd:
"We have some late breaking reports that a patch series to rework clk
rate range support broke boot on some devices, so I've left that
branch out of this. Hopefully we can get to that next week, or punt on
it and let it bake another cycle. That means we don't really have any
changes to the core framework this time around besides a few typo
fixes. Instead this is all clk driver updates and fixes.
The usual suspects are here (again), with Qualcomm dominating the
diffstat. We look to have gained support for quite a few new Qualcomm
SoCs and Dmitry worked on updating many of the existing Qualcomm
drivers to use clk_parent_data. After that we have MediaTek drivers
getting some much needed updates, in particular to support GPU DVFS.
There are also quite a few Samsung clk driver patches, but that's
mostly because there was a maintainer change and so last release we
missed some of those patches.
Overall things look normal, but I'm slowly reviewing core framework
code nowadays and that shows given the rate range patches had to be
yanked last minute. Let's hope this situation changes soon.
New Drivers:
- Support for Renesas VersaClock7 clock generator family
- Add Spreadtrum UMS512 SoC clk support
- New clock drivers for MediaTek Helio X10 MT6795
- Display clks for Qualcomm SM6115, SM8450
- GPU clks for Qualcomm SC8280XP
- Qualcomm MSM8909 and SM6375 global and SMD RPM clk drivers
Deleted Drivers:
- Remove DaVinci DM644x and DM646x clk driver support
Updates:
- Convert Baikal-T1 CCU driver to platform driver
- Split reset support out of primary Baikal-T1 CCU driver
- Add some missing clks required for RPiVid Video Decoder on
RaspberryPi
- Mark PLLC critical on bcm2835
- More devm helpers for fixed rate registration
- Various PXA168 clk driver fixes
- Add resets for MediaTek MT8195 PCIe and USB
- Miscellaneous of_node_put() fixes
- Nuke dt-bindings/clk path (again) by moving headers to
dt-bindings/clock
- Convert gpio-clk-gate binding to YAML
- Various fixes to AMD/Xilinx Zynqmp clk driver
- Graduate AMD/Xilinx "clocking wizard" driver from staging
- Add missing DPI1_HDMI clock in MT8195 VDOSYS1
- Clock driver changes to support GPU DVFS on MT8183, MT8192, MT8195
- Fix GPU clock topology on MT8195
- Propogate rate changes from GPU clock gate up the tree
- Clock mux notifiers for GPU-related PLLs
- Conversion of more "simple" drivers to mtk_clk_simple_probe()
- Hook up mtk_clk_simple_remove() for "simple" MT8192 clock drivers
- Fixes to previous |struct clk| to |struct clk_hw| conversion on
MediaTek
- Shrink MT8192 clock driver by deduplicating clock parent lists
- Change order between 'sim_enet_root_clk' and 'enet_qos_root_clk'
clocks for i.MX8MP
- Drop unnecessary newline in i.MX8MM dt-bindings
- Add more MU1 and SAI clocks dt-bindings Ids
- Introduce slice busy bit check for i.MX93 composite clock
- Introduce white list bit check for i.MX93 composite clock
- Add new i.MX93 clock gate
- Add MU1 and MU2 clocks to i.MX93 clock provider
- Add SAI IPG clocks to i.MX93 clock provider
- add generic clocks for U(S)ART available on SAMA5D2 SoCs
- reset controller support for Polarfire clocks
- .round_rate and .set rate support for clk-mpfs
- code cleanup for clk-mpfs
- PLL support for PolarFire SoC's Clock Conditioning Circuitry
- Add watchdog, I2C, pin control/GPIO, and Ethernet clocks on R-Car
V4H
- Add SDHI, Timer (CMT/TMU), and SPI (MSIOF) clocks on R-Car S4-8
- Add I2C clocks and resets on RZ/V2M
- Document clock support for the RZ/Five SoC
- mux-variant clock using the table variant to select parents
- clock controller for the rv1126 soc
- conversion of rk3128 to yaml and relicensing of the yaml bindings
to gpl2+MIT (following dt-binding guildelines)
- Exynos7885: add FSYS, TREX and MFC clock controllers
- Exynos850: add IS and AUD (audio) clock controllers with bindings
- ExynosAutov9: add FSYS clock controllers with bindings
- ExynosAutov9: correct clock IDs in bindings of Peric 0 and 1 clock
controllers, due to duplicated entries. This is an acceptable ABI
break: recently developed/added platform so without legacies, acked
by known users/developers
- ExynosAutov9: add few missing Peric 0/1 gates
- ExynosAutov9: correct register offsets of few Peric 0/1 clocks
- Minor code improvements (use of_device_get_match_data() helper,
code style)
- Add Krzysztof Kozlowski as co-maintainer of Samsung SoC clocks, as
he already maintainers that architecture/platform
- Keep Qualcomm GDSCs enabled when PWRSTS_RET flag is there, solving
retention issues during suspend of USB on Qualcomm sc7180/sc7280
and SC8280XP
- Qualcomm SM6115 and QCM2260 are moved to reuse PLL configuration
- Qualcomm SDM660 SDCC1 moved to floor clk ops
- Support for the APCS PLLs for Qualcomm IPQ8064, IPQ8074 and IPQ6018
was added/fixed
- The Qualcomm MSM8996 CPU clocks are updated with support for ACD
- Support for Qualcomm SDM670 GCC and RPMh clks was added
- Transition to parent_data, parent_hws and use of ARRAY_SIZE() for
num_parents was done for many Qualcomm SoCs
- Support for per-reset defined delay on Qualcomm was introduced"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (283 commits)
clk: qcom: gcc-sm6375: Ensure unsigned long type
clk: qcom: gcc-sm6375: Remove unused variables
clk: qcom: kpss-xcc: convert to parent data API
clk: introduce (devm_)hw_register_mux_parent_data_table API
clk: allow building lan966x as a module
clk: clk-xgene: simplify if-if to if-else
clk: ast2600: BCLK comes from EPLL
clk: clocking-wizard: Depend on HAS_IOMEM
clk: clocking-wizard: Use dev_err_probe() helper
clk: nxp: fix typo in comment
clk: pxa: add a check for the return value of kzalloc()
clk: vc5: Add support for IDT/Renesas VersaClock 5P49V6975
dt-bindings: clock: vc5: Add 5P49V6975
clk: mvebu: armada-37xx-tbg: Remove the unneeded result variable
clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
clk: Renesas versaclock7 ccf device driver
dt-bindings: Renesas versaclock7 device tree bindings
clk: ti: Balance of_node_get() calls for of_find_node_by_name()
clk: imx: scu: fix memleak on platform_device_add() fails
clk: vc5: Use regmap_{set,clear}_bits() where appropriate
...
|
|
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices
supported and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before, and
some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different USB
drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: gadget: uvc: don't put item still in use
usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
usb: host: ehci-exynos: switch to using gpiod API
Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
dt-bindings: usb: Convert FOTG210 to dt schema
usb: mtu3: fix failed runtime suspend in host only mode
USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
usb: typec: Replace custom implementation of device_match_fwnode()
usb: typec: ucsi: Don't warn on probe deferral
usb: add quirks for Lenovo OneLink+ Dock
MAINTAINERS: switch dwc3 to Thinh
usb: idmouse: fix an uninit-value in idmouse_open
USB: PHY: JZ4770: Switch to use dev_err_probe() helper
usb: phy: generic: Switch to use dev_err_probe() helper
usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
usb: cdns3: remove dead code
usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
usb: musb: sunxi: Switch to use dev_err_probe() helper
...
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the changes fall into one of three categories: adding support
for additional devices on existing machines, cleaning up issues found
by the ongoing conversion to machine-readable bindings, and addressing
minor mistakes in the existing DT data.
Across SoC vendors, Qualcomm and Freescale stick out as getting the
most updates, which corresponds to their dominance in the mobile phone
and embedded industrial markets, respectively.
There are 636 non-merge changeset in this branch, which is a little
lower than most times, but more importantly we only add 36 machine
files, which is about half of what we had the past few releases.
Eight new SoCs are added, but all of them are variations of already
supported SoC families, and most of them come with one reference board
design from the SoC vendor:
- Mediatek MT8186 is a Chromebook/Tablet type SoC, similar to the
MT65xx series of phone SoCs, with two Cortex-A76 and six Cortex-A55
cores.
- TI AM62A is another member of the K3 family with Cortex-A53 cores,
this one is targetted at Video/Vision processing for industrial and
automotive applications.
- NXP i.MX8DXL is another chip for this market in the ever-growing
i.MX8 family, this one again with two Cortex-A35 cores.
- Renesas R-Car H3Ne-1.7G (R8A779MB) and R-Car V3H2 (R8A77980A) are
minor updates of R8A77951 and R8A77980, respectively.
- Qualcomm IPQ8064-v2.0, IPQ8062 and IPQ8065 are all variants of the
IPQ8064 chip, with minimally different features.
The AMD Pensando Elba and Apple M1 Ultra SoC support was getting close
this time, but in the end did not make the cut.
The new machines based on existing SoC support are fairly uneventful:
- Sony Xperia 1 IV is a fairly recent phone based on Qualcomm
Snapdragon 8 Gen 1.
- Three Samsung phones based on Snapdragon 410: Galaxy E5, E7 and
Grand Max. These are added for both 32-bit and 64-bit kernels, as
they originally shipped running 32-bit code.
- Two new servers using AST2600 BMCs: AMD DaytonaX and Ampere Mt.
Mitchell
- Three new machines based on Rockchips RK3399 and RK3566: Anberic
RG353P and RG503, Pine64 Pinephone Pro, Open AI Lab
- Multiple NXP i.MX6/i.MX8 based boards: Kontron SL/BL i.MX8MM OSM-S,
i.MX8MM Gateworks GW7904, MSC SM2S-IMX8PLUS SoM and carrier board
- Two development boards in the Microchip AT91 family: SAMA5D3-EDS
and lan966x-pcb8290.
- Minor variants of existing boards using Amlogic, Broadcom, Marvell,
Rockchips, Freescale Layerscape and Socionext Uniphier SoCs"
* tag 'arm-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (617 commits)
Revert "ARM: dts: BCM5301X: Add basic PCI controller properties"
ARM: dts: s5pv210: correct double "pins" in pinmux node
ARM: dts: exynos: fix polarity of VBUS GPIO of Origen
arm64: dts: exynos: fix polarity of "enable" line of NFC chip in TM2
arm64: dts: uniphier: Add L2 cache node
arm64: dts: uniphier: Remove compatible "snps,dw-pcie" from pcie node
arm64: dts: uniphier: Fix opp-table node name for LD20
arm64: dts: uniphier: Add USB-device support for PXs3 reference board
arm64: dts: uniphier: Add ahci controller nodes for PXs3
arm64: dts: uniphier: Use GIC interrupt definitions
arm64: dts: uniphier: Rename gpio-hog nodes
arm64: dts: uniphier: Rename usb-glue node for USB3 to usb-controller
arm64: dts: uniphier: Rename usb-phy node for USB2 to usb-controller
arm64: dts: uniphier: Rename pvtctl node to thermal-sensor
ARM: dts: uniphier: Remove compatible "snps,dw-pcie-ep" from pcie-ep node
ARM: dts: uniphier: Move interrupt-parent property to each child node in uniphier-support-card
ARM: dts: uniphier: Add ahci controller nodes for PXs2
ARM: dts: uniphier: Add ahci controller nodes for Pro4
ARM: dts: uniphier: Use GIC interrupt definitions
ARM: dts: uniphier: Rename gpio-hog node
...
|
|
Samsung DTS ARM and ARM64 changes for v6.1
Late cleanup and fixes for Samsung DTS:
1. Fix polarity of pins:
- enable GPIO of NFC chip in Exynos5433 TM2 boards,
- vbus GPIO of EHCI in Exynos4412 Origen board.
2. Correct name of pin configuration nodes - redundant "pins" in the
name (no functional impact).
* tag 'samsung-dt-dt64-6.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s5pv210: correct double "pins" in pinmux node
ARM: dts: exynos: fix polarity of VBUS GPIO of Origen
arm64: dts: exynos: fix polarity of "enable" line of NFC chip in TM2
Link: https://lore.kernel.org/r/20221003073916.12588-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Kalle Valo says:
====================
wireless-next patches for v6.1
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
- refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
- support CYW43439 SDIO chipset
- support BCM4378 on Apple platforms
- support CYW89459 PCIe chipset
rtw89
- more work to get rtw8852c supported
- P2P support
- support for enabling and disabling MSDU aggregation via nl80211
mt76
- tx status reporting improvements
ath11k
- cold boot calibration support on WCN6750
- Target Wake Time (TWT) debugfs support for STA interface
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- implement SRAM dump debugfs interface
- enable threaded NAPI on all hardware
- WoW support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
wcn36xx
- add SNR from a received frame as a source of system entropy
* tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (231 commits)
wifi: rtl8xxxu: Improve rtl8xxxu_queue_select
wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM
wifi: rtl8xxxu: gen2: Enable 40 MHz channel width
wifi: rtw89: 8852b: configure DLE mem
wifi: rtw89: check DLE FIFO size with reserved size
wifi: rtw89: mac: correct register of report IMR
wifi: rtw89: pci: set power cut closed for 8852be
wifi: rtw89: pci: add to do PCI auto calibration
wifi: rtw89: 8852b: implement chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add DMA busy checking bits to chip info
wifi: rtw89: mac: define DMA channel mask to avoid unsupported channels
wifi: rtw89: pci: mask out unsupported TX channels
iwlegacy: Replace zero-length arrays with DECLARE_FLEX_ARRAY() helper
ipw2x00: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
wifi: iwlwifi: Track scan_cmd allocation size explicitly
brcmfmac: Remove the call to "dtim_assoc" IOVAR
brcmfmac: increase dcmd maximum buffer size
brcmfmac: Support 89459 pcie
brcmfmac: increase default max WOWL patterns to 16
cw1200: fix incorrect check to determine if no element is found in list
...
====================
Link: https://lore.kernel.org/r/20220930150413.A7984C433D6@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to s3fwrn5 driver code the "enable" GPIO line is driven "high"
when chip is not in use (mode is S3FWRN5_MODE_COLD), and is driven "low"
when chip is in use.
s3fwrn5_phy_power_ctrl():
...
gpio_set_value(phy->gpio_en, 1);
...
if (mode != S3FWRN5_MODE_COLD) {
msleep(S3FWRN5_EN_WAIT_TIME);
gpio_set_value(phy->gpio_en, 0);
msleep(S3FWRN5_EN_WAIT_TIME);
}
Therefore the line described by "en-gpios" property should be annotated
as "active low".
The wakeup gpio appears to have correct polarity (active high).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20220929011557.4165216-1-dmitry.torokhov@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Update the name of property 'clk_csr' as 'snps,clk-csr' to align with
the property name in the binding file.
Signed-off-by: Jianguo Zhang <jianguo.zhang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Updates from Kunihiko Hayashi via email:
"Update devicetree sources for UniPhier armv8 SoCs to remove dtschema
warnings, add support existing features that haven't yet been
described, and replace constants with macros."
* uniphier/dt:
arm64: dts: uniphier: Add L2 cache node
arm64: dts: uniphier: Remove compatible "snps,dw-pcie" from pcie node
arm64: dts: uniphier: Fix opp-table node name for LD20
arm64: dts: uniphier: Add USB-device support for PXs3 reference board
arm64: dts: uniphier: Add ahci controller nodes for PXs3
arm64: dts: uniphier: Use GIC interrupt definitions
arm64: dts: uniphier: Rename gpio-hog nodes
arm64: dts: uniphier: Rename usb-glue node for USB3 to usb-controller
arm64: dts: uniphier: Rename usb-phy node for USB2 to usb-controller
arm64: dts: uniphier: Rename pvtctl node to thermal-sensor
ARM: dts: uniphier: Remove compatible "snps,dw-pcie-ep" from pcie-ep node
ARM: dts: uniphier: Move interrupt-parent property to each child node in uniphier-support-card
ARM: dts: uniphier: Add ahci controller nodes for PXs2
ARM: dts: uniphier: Add ahci controller nodes for Pro4
ARM: dts: uniphier: Use GIC interrupt definitions
ARM: dts: uniphier: Rename gpio-hog node
ARM: dts: uniphier: Rename usb-glue node for USB3 to usb-controller
ARM: dts: uniphier: Rename usb-phy node for USB2 to usb-controller
ARM: dts: uniphier: Rename pvtctl node to thermal-sensor
|
|
Add a L2 cache node referenced from CPU nodes as the missing cache hierarchy
information because the following warning was issued.
cacheinfo: Unable to detect cache hierarchy for CPU 0
Early cacheinfo failed, ret = -2
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-11-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The generic platform driver pcie-designware-plat.c doesn't work for
UniPhier PCIe host controller, because the controller has some
necessary initialization sequence for the controller-specific logic.
Currently the controller doesn't use "snps,dw-pcie" compatible,
so this is no longer needed. Remove the compatible string from the
pcie node.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-10-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
To fix dtbs_check warning:
uniphier-ld20-akebi96.dt.yaml: opp-table0: $nodename:0: 'opp-table0' does not match '^opp-table(-[a-z0-9]+)?$'
From schema: Documentation/devicetree/bindings/opp/opp-v2.yaml
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-9-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
PXs3 reference board can change each USB port 0 and 1 to device mode
with jumpers. Prepare devicetree sources for USB port 0 and 1.
This specifies dr_mode, pinctrl, and some quirks and removes nodes for
unused phys and vbus-supply properties.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-8-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add ahci core controller and glue layer nodes including reset-controller
and sata-phy.
This supports for PXs3 and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-7-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use human-readable definitions for GIC interrupt type and flag, instead of
hard-coding the numbers. No functional change.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-6-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
According to gpio-hog schema, should add the suffix "-hog" to the node
names including gpio-hog to fix the following warning.
uniphier-ld11-ref.dtb: gpio@55000000: 'xirq0' does not match any of the regexes: '^.+-hog(-[0-9+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/gpio/socionext,uniphier-gpio.yaml
This applies to the devicetre for LD11, LD20 and PXs3 SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-5-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This "usb-glue" stands for an external controller associated with USB core,
however, this is not common. So rename to "usb-controller".
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-4-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Actual phy nodes are each child node. The parent node should be
usb-controller node as a representation of the phy integration.
This applies to the devicetree for LD11 SoC.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-3-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The pvtctl node belongs to thermal-sensor, so the node name should be
renamed to thermal-sensor.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-2-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
RK3399-Nanopi-R4S-enterprise as variant board, Gru-Scarlet SKU variants,
DSI support for rk356x, display-gamma-control for rk3399, display
output for quartz64-b and rk3566-roc-pc, hdmi supplies for rk3399-roc-pc,
some pinctrl improvements for the px30-evb and a number of changes to
bring rk3399 rock4 and rock-pi4 structure closer to names used in schematics.
* tag 'v6.1-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: use pin constant for reset-gpios on px30-evb
arm64: dts: rockchip: add pinctrl for mipi-pdn pin on px30-evb
arm64: dts: rockchip: set max drive-strength for cif_clkout_m0 on px30-evb
arm64: dts: rockchip: add avdd-0v9-supply and avdd-1v8-supply on rk3399 rock 4c and pi4
arm64: dts: rockchip: sort nodes/properties on rk3399-rock-4
arm64: dts: rockchip: fix regulator name on rk3399-rock-4
arm64: dts: rockchip: sort nodes/properties on rk3399-rock-4c-plus
arm64: dts: rockchip: fix regulator structure on rk3399-rock-4c-plus
arm64: dts: rockchip: connect vcca_1v8 to APIO5_VDD on rk3399-rock-4c-plus
arm64: dts: rockchip: Add DSI and DSI-DPHY nodes to rk356x
arm64: dts: rockchip: Enable HDMI and GPU on quartz64-b
arm64: dts: rockchip: Add RK3399 NanoPi R4S Enterprise Edition
dt-bindings: Add doc for FriendlyARM NanoPi R4S Enterprise Edition
arm64: dts: rockchip: add i2s0 I2S/PDM/TDM 8ch controller to px30
arm64: dts: rockchip: Add HDMI supplies on rk3399-roc-pc
arm64: dts: rockchip: Support gru-scarlet sku{2,4} variants
dt-bindings: arm: rockchip: Add gru-scarlet sku{2,4} variants
arm64: dts: rockchip: enable gamma control on RK3399
arm64: dts: rockchip: Enable video output on rk3566-roc-pc
Link: https://lore.kernel.org/r/38114097.10thIPus4b@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull ARM SoC fixes from Arnd Bergmann:
"This should be the last set of bugfixes in the SoC tree:
- Two fixes for Arm integrator, dealing with a regression caused by
invalid DT properties combined with a change in dma address
translation, and missing device_type annotations on the PCI bus
- Fixes for drivers/reset/, addressing bugs in i.MX8MP, Sparx5 and
NPCM8XX platforms
- Bjorn Andersson's email address changes in the MAINTAINERS file
- Multiple minor fixes to Qualcomm dts files, and a change to the
remoteproc firmware filename that did not match the actual path in
the linux-firmware package
- Minor code fixes for the Allwinner/sunxi SRAM driver, and the
broadcom STB Bus Interface Unit driver
- A build fix for the sunplus sp7021 platform
- Two dts fixes for TI OMAP family SoCs, addressing an extraneous
usb4 device node and an incorrect DMA handle"
* tag 'soc-fixes-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: integrator: Fix DMA ranges
ARM: dts: integrator: Tag PCI host with device_type
ARM: sunplus: fix serial console kconfig and build problems
reset: npcm: fix iprst2 and iprst4 setting
arm64: dts: qcom: sm8350: fix UFS PHY serdes size
soc: bcm: brcmstb: biuctrl: Avoid double of_node_put()
arm64: dts: qcom: sc8280xp-x13s: Update firmware location
soc: sunxi: sram: Fix debugfs info for A64 SRAM C
soc: sunxi: sram: Fix probe function ordering issues
soc: sunxi: sram: Prevent the driver from being unbound
soc: sunxi: sram: Actually claim SRAM regions
ARM: dts: am5748: keep usb4_tm disabled
reset: microchip-sparx5: issue a reset on startup
reset: imx7: Fix the iMX8MP PCIe PHY PERST support
MAINTAINERS: Update Bjorn's email address
arm64: dts: qcom: sc7280: move USB wakeup-source property
arm64: dts: qcom: thinkpad-x13s: Fix firmware location
arm64: dts: qcom: sm8150: Fix fastrpc iommu values
ARM: dts: am33xx: Fix MMCHS0 dma properties
|
|
We need the USB fixes in here for other follow-on changes to be able to
be applied successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mvebu dt64 for 6.1 (part 1)
- Add UART1-3 for AC5/AC5X SoC
- Improve uDPU support (Aramda 3720 based board)
- Add new eDPU based on uDPU
* tag 'mvebu-dt64-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: 98dx25xx: use correct property for i2c gpios
arm64: dts: marvell: add support for Methode eDPU
dt-bindings: marvell: armada-37xx: add Methode eDPU compatible
arm64: dts: marvell: split Methode uDPU DTS
arm64: dts: marvell: rename temp sensor nodes
arm64: dts: marvell: uDPU: remove LED node pinctrl-names
arm64: dts: marvell: uDPU: align LED-s with bindings
arm64: dts: marvell: uDPU: add missing SoC compatible
arm64: dts: marvell: espressobin-ultra: add generic Espressobin compatible
dt-bindings: marvell: convert Armada 37xx compatibles to YAML
dt-bindings: vendor-prefixes: add Methode Electronics
arm64: dts: marvell: Add UART1-3 for AC5/AC5X
Link: https://lore.kernel.org/r/87h70yxfmy.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Qualcomm ARM64 DTS fixes for 6.0
This corrects invalid IOMMU streams for the SM8150 CDSP FastRPC, moves
the wakeup-source of SC7280 USB nodes to the correct place, fixes the
SM8350 UFS PHY serdes size to not overlap with the other subnodes and
updates the firmware location for the Lenovo ThinkPad X13s to match the
movement in linux-firmware.
It also updates MAINTAINERS and .mailmap to reflect the changes in my
email address.
* tag 'qcom-arm64-fixes-for-6.0' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sm8350: fix UFS PHY serdes size
arm64: dts: qcom: sc8280xp-x13s: Update firmware location
MAINTAINERS: Update Bjorn's email address
arm64: dts: qcom: sc7280: move USB wakeup-source property
arm64: dts: qcom: thinkpad-x13s: Fix firmware location
arm64: dts: qcom: sm8150: Fix fastrpc iommu values
Link: https://lore.kernel.org/r/20220921142939.1310163-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Qualcomm ARM64 DTS updates for 6.1
Support for Samsung Galaxy E5, E7 and Grand Max is added, with support
for both 32-bit and 64-bit variants. The Samsung Galaxy S4 Mini Value
Edition gains magnetometer support.
MSM8996-based Xiaomi devices gains descriptions of the LPG-based LEDs.
On SA8295P ADP problems arising from regulators being switched into
low-power mode is worked around by removing this ability, for now.
The onboard USB Hub on SC7180 Trogdor is finally described and a few ADC
related updates are introduced.
On SC7280 support for the CPU and LLC bwmon instances are introduced.
Soundwire, audio codecs and sound introduced for a variety of boards.
Using required-opps the USB controllers votes for a minimum corner on
VDD_CX.
The onboard USB Hub Herobrine is described. A new board, the Google
Evoker is added, as is another revision of Herobrine Villager.
On SC8280XP the USB controllers are marked as wakeup-sources, to keep
them powered during suspend. The CRD has HID devices marked as
wakeup-sources to enable resuming the system. In addition to these
changes the alternative touchpad is introduced on the Lenovo ThinkPad
X13s.
SDM845 gains RPMh stats support and the LLCC BWMON is added. For SM6350
interconnect providers and GPI DMA is introduced. A description of the
PM7280b PMIC is added to Fairphone FP4 on SM7225.
With the multi-MSI support added in the PCIe controller, SM8250 gets all
its MSI interrupts added.
UFS ICE and the second SDHCI controller is introduced on SM8450. Support
for the Sony Xperia 1 IV is introduced.
Throughout a variety of platforms the TCSR mutex syscon is replaced with
the MMIO-based binding. TCSR nodes gained proper compatibles and halt
syscon nodes are split out from the mutex ranges.
A range of fixes to align with DT bindings are introduced. Among these
are the changes to the follow the TLMM binding and suffix pinctrl states
with -state and subnodes thereof with -pins, another is a number of
changes transitioning to use -gpios and introduction of proper parent
clock references in various clock providers.
* tag 'qcom-arm64-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (136 commits)
arm64: dts: qcom: sc7280: Add required-opps for USB
arm64: dts: qcom: sm8450: fix UFS PHY serdes size
arm64: dts: qcom: ipq8074: fix PCIe PHY serdes size
arm64: dts: qcom: sa8295p-adp: add missing gpio-ranges in PMIC GPIOs
arm64: dts: qcom: sa8295p-adp: add fallback compatible to PMIC GPIOs
arm64: dts: qcom: msm8996-xiaomi: align PMIC GPIO pin configuration with DT schema
arm64: dts: qcom: msm8994-msft-lumia-octagon: align resin node name with bindings
arm64: dts: qcom: pmi8994: add missing MPP compatible fallback
dt-bindings: pci: QCOM Add missing sc7280 aggre0, aggre1 clocks
arm64: dts: qcom: sc7280: Add missing aggre0, aggre1 clocks
arm64: dts: qcom: sc7280-villager: Adjust LTE SKUs
dt-bindings: arm: qcom: Adjust LTE SKUs for sc7280-villager
arm64: dts: qcom: sc7280-herobrine: Add nodes for onboard USB hub
arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub
arm64: dts: qcom: align SDHCI reg-names with DT schema
arm64: dts: qcom: sm8250: provide additional MSI interrupts
arm64: dts: qcom: msm8996: add #clock-cells and XO clock to the HDMI PHY node
arm64: dts: qcom: Use WCD9335 DT bindings
arm64: dts: qcom: msm8994: switch TCSR mutex to MMIO
arm64: dts: qcom: ipq6018: switch TCSR mutex to MMIO
...
Link: https://lore.kernel.org/r/20220921234854.1343238-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
TI K3 device tree updates for v6.1
New Features:
AM62A:
* Basic support for AM62A SoC and SK Board
AM62:
* EPWM support
AM64:
* GPMC, LED, Crypto accelerator support
Fixes:
J7200 pinmux node update
Fixes for Crypto and RNG accelerators on AM65, J721e, J7200
Cleanups:
Reorder SoC compatible and pinmux macros alphabetically
* tag 'ti-k3-dt-for-v6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux: (22 commits)
arm64: dts: ti: k3-j7200: fix main pinmux range
arm64: dts: ti: Add support for AM62A7-SK
arm64: dts: ti: Introduce AM62A7 family of SoCs
dt-bindings: pinctrl: k3: Introduce pinmux definitions for AM62A
dt-bindings: arm: ti: Add bindings for AM62A7 SoC
dt-bindings: arm: ti: Rearrange IOPAD macros alphabetically
arm64: dts: ti: k3-am625-sk: Add epwm nodes
arm64: dts: ti: k3-am62-main: Add epwm nodes
arm64: dts: ti: k3-am642-sk: Add DT entry for onboard LEDs
arm64: dts: ti: k3-j7200-mcu-wakeup: Add SA2UL node
arm64: dts: ti: k3-am65-main: Do not exclusively claim SA2UL
arm64: dts: ti: k3-am65-main: Move SA2UL to unused PSI-L thread ID
arm64: dts: ti: k3-am65-main: Disable RNG node
arm64: dts: ti: k3-j7200-main: Add main domain watchdog entries
arm64: dts: ti: k3-am64-main: Add ELM (Error Location Module) node
arm64: dts: ti: k3-am64-main: Add GPMC memory controller node
arm64: dts: ti: k3-j721e-main: fix RNG node clock id
arm64: dts: ti: k3-am64-main: Enable crypto accelerator
arm64: dts: ti: k3-am64: Add SA2UL address space to Main CBASS ranges
arm64: dts: ti: k3-am64-main: Add main_cpts label
...
Link: https://lore.kernel.org/r/44729b46-27f9-94a0-17ed-8868649a4a0a@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Renesas ARM DT updates for v6.1 (take two)
- Merge Renesas ARM/ARM64 maintainers entries,
- CAN support for the RZ/N1 SoC and the RZN1D-DB development board,
- Watchdog, pin control, I2C (EEPROM), GPIO (LEDS/switches), and
Ethernet support for the R-Car V4H SoC and the White Hawk
development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v6.1-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (26 commits)
arm64: dts: renesas: Adjust whitespace around '{'
arm64: dts: renesas: rzg2ul-smarc: Include SoM DTSI into board DTS
arm64: dts: renesas: rzg2ul-smarc-som: Drop enabling wdt2
ARM: dts: renesas: Fix USB PHY device and child node names
arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values
arm64: dts: renesas: white-hawk-cpu: Add missing bootargs
arm64: dts: renesas: spider-cpu: Add missing bootargs
arm64: dts: renesas: spider: Move aliases and chosen
arm64: dts: renesas: white-hawk-cpu: Add Ethernet support
arm64: dts: renesas: white-hawk: Move aliases and chosen
arm64: dts: renesas: r8a779g0: Add RAVB nodes
arm64: dts: renesas: white-hawk-cpu: Add push switches
arm64: dts: renesas: white-hawk-cpu: Add GP LEDs
arm64: dts: renesas: r8a779g0: Add GPIO nodes
arm64: dts: renesas: white-hawk: Add Ethernet sub-board
arm64: dts: renesas: white-hawk: Add CSI/DSI sub-board
arm64: dts: renesas: white-hawk: Add I2C0 and EEPROMs
arm64: dts: renesas: r8a779g0: Add I2C nodes
arm64: dts: renesas: white-hawk-cpu: Add serial port pin control
arm64: dts: renesas: r8a779g0: Add pinctrl device node
...
Link: https://lore.kernel.org/r/cover.1663588776.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
mt6795:
- add add system timer node
mt7986a:
- add wifi support
mt8183:
- add MDP3 and keypad
mt8186:
- basic support for the Evaluation Board including, i2c, usb and uart.
mt8192:
- add nodes to support PWM, MIPI transciever, display with GCE and DSI.
mt8195:
- disable nodes not used on all boards
- Add support for CPU freq, clocks, power domain controller, spmi, scp.
- Enable audio decoder, DSP, IOMMU, mailbox.
- Add display nodes for vdosys0.
- On Cherry based chromebooks, enable the system companion processor,
Cross EC, Google Security Chip, secondary MMC controller, trackpad and
a few regulators.
* tag 'v6.0-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: (34 commits)
arm64: dts: mediatek: mt6795: Add CPUX system timer node
arm64: dts: mt7986: add built-in Wi-Fi device nodes
arm64: dts: mediatek: cherry: Enable MT6315 regulators on SPMI bus
arm64: dts: mediatek: cherry: Enable Elantech eKTH3000 i2c trackpad
arm64: dts: mediatek: cherry: Enable secondary SD/MMC controller
arm64: dts: mediatek: cherry: Add keyboard mapping for the top row
arm64: dts: mediatek: cherry: Add Google Security Chip (GSC) TPM
arm64: dts: mediatek: cherry: Wire up the ChromeOS Embedded Controller
arm64: dts: mediatek: cherry: Enable the System Companion Processor
arm64: dts: mediatek: Fix build warnings of mt8173 vcodec nodes
arm64: dts: mediatek: Add missing xHCI clocks for mt8192 and mt8195
arm64: dts: mt8192: Add dsi node
arm64: dts: mt8192: Add display nodes
arm64: dts: mediatek: Add mmsys #reset-cells property for mt8192
arm64: dts: mt8192: Add mipi_tx node
arm64: dts: mt8192: Add pwm node
arm64: dts: Add MediaTek MT8186 dts and evaluation board and Makefile
arm64: dts: mt8195: Add display node for vdosys0
arm64: dts: mt8195: Add gce node
arm64: dts: mt8195: Add iommu and smi nodes
...
Link: https://lore.kernel.org/r/3b915692-c8a9-c508-5a4a-0fdb49355e99@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
- Allwinner A100 DMA node
- Allwinner H6 GPU devfreq scaling
- sunxi sram bindings cleanup and D1 addition
* tag 'sunxi-dt-for-6.1-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
dt-bindings: sram: sunxi-sram: Add D1 compatible string
dt-bindings: sram: sunxi-sram: Clean up the compatible lists
arm64: dts: allwinner: beelink-gs1: Enable GPU OPP
arm64: dts: allwinner: h6: Add GPU OPP table
arm64: dts: allwinner: h6: Add cooling map for GPU
arm64: dts: allwinner: a100: Add I2C DMA requests
arm64: dts: allwinner: a100: Add device node for DMA controller
Link: https://lore.kernel.org/r/YyePKDnOeP8Tdt5n@kista.localdomain
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX arm64 device tree change for 6.1:
- New board support: i.MX8DXL EVK, Kontron SL/BL i.MX8MM OSM-S, i.MX8MM
Gateworks GW7904, MSC SM2S-IMX8PLUS SoM and carrier board, NXP
LS2081ARDB.
- Update i.MX8MQ device tree to use generic name 'dma-controller' for
SDMA.
- A number of i.MX8ULP device tree improvements and updates: correct
parent clock of LPI2C & LPSPI, increase the clock speed of LPSPI, add
PMU and mailbox device, drop undocumented CGC property, enable FEC, etc.
- Add interconnect property for various i.MX8MP blk-ctrl devices.
- Enable VPU PGC, blk-ctrl and PCIe support for i.MX8MP SoC.
- A set of changes from Peng Fan to add various devices for i.MX93 SoC,
including MU, blk-ctrl, PMU, LPI2C, LPSPI, SRC, etc.
- Two set of changes to update LS1043A and LS1046A device trees on
various aspects, including USB3, PCIe, DMA, mdio-mux, QSPI Flash, etc.
- Board imx8mq-librem5 update: add USB role switching, add RGB PWM
notification LEDs, add voice coil motor for focus control, fix MIPI_CSI
description.
- A series from Frieder Schrempf to improve imx8mm-kontron device trees
for VSELECT switch, DDRC operating point, SPI NOR partition layout etc.
- A set of display and PMIC related additions and improvements on
imx8mm-verdin board.
- A number of i.MX8M Plus DHCOM PDK2 device tree improvments from Marek
Vasut.
- A few imx8mp-venice device tree updates on USB, cpufreq and WiFi/BT.
- A series from Vladimir Oltean to enable multiple switch CPU ports
support.
- Other small and random board specific updates.
* tag 'imx-dt64-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (90 commits)
arm64: dts: ls1046a-qds: Modify the qspi flash frequency
arm64: dts: ls1046a-qds: add mmio based mdio-mux nodes for FPGA
arm64: dts: ls1046a: add gpios based i2c recovery information
arm64: dts: ls1046a: use a pseudo-bus to constrain usb and sata dma size
arm64: dts: ls1046a: make dma-coherent global to the SoC
arm64: dts: ls1046a: add missing dma ranges property
arm64: dts: ls1046a: Add big-endian property for PCIe nodes
arm64: dts: ls1046a: Add the PME interrupt and big-endian to PCIe EP nodes
arm64: dts: ls1046a: Enable usb3-lpm-capable for usb3 node
arm64: dts: ls1043a-rdb: add pcf85263 rtc node
arm64: dts: ls1043a-qds: add mmio based mdio-mux support
arm64: dts: ls1043a: use a pseudo-bus to constrain usb and sata dma size
arm64: dts: ls1043a: add gpio based i2c recovery information
arm64: dts: ls1043a: make dma-coherent global to the SoC
arm64: dts: ls1043a: add missing dma ranges property
arm64: dts: ls1043a: Add big-endian property for PCIe nodes
arm64: dts: ls1043a: Add SCFG phandle for PCIe nodes
arm64: dts: ls1043a: use pcie aer/pme interrupts
arm64: dts: ls1043a: Enable usb3-lpm-capable for usb3 node
arm64: dts: ls1043a: fix the wrong size of dcfg space
...
Link: https://lore.kernel.org/r/20220918092806.2152700-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use rk gpio naming convention into reset-gpios of ov5695 camera
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Link: https://lore.kernel.org/r/20220620161321.1898840-4-tommaso.merciai@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add right mux for mipi-pdn. Mux this pad as gpio2 14
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Link: https://lore.kernel.org/r/20220620161321.1898840-3-tommaso.merciai@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add max drive-strength for cif_clkout_m0. This fix the issue that
sometimes camera ov5695 is not probed correctly.
Tested on PX30_Mini_EVB_V11_20190507
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Link: https://lore.kernel.org/r/20220620161321.1898840-2-tommaso.merciai@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
this patch adds avdd-0v9-supply and avdd-1v8-supply to hdmi node for
Radxa ROCK 4 series.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220909195006.127957-6-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
sort nodes/properties alphabetically
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220909195006.127957-5-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
fix regulator name
ref:
https://dl.radxa.com/rockpi4/docs/hw/rockpi4/rockpi4_v13_sch_20181112.pdf
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220909195006.127957-4-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
Arnd Bergmann
Cristian Marussi
Ioana Ciornei
Peng Fan
Li Jun
Max Krummenacher
Marek Vasut
Linus Torvalds
Jakub Kicinski
Dmitry Torokhov
Jianguo Zhang
Kunihiko Hayashi
Greg Kroah-Hartman
Tommaso Merciai
FUKAUMI Naoki